English dropdown-ico

Manual Simplicity 1692243

20 pages 0.32 mb
Download

Go to site of 20

Summary
  • Simplicity 1692243 - page 1

    OPERATOR’S MANUAL 47” Two-Stage Commercial Snowthrower Mfg. No. 1692243 Hitch Mfg. No. 1692244 ...

  • Simplicity 1692243 - page 2

    HEX CAPSCREW CARRIAGE BOLT 0 @ @ @ PLAIN WASHER LOCKWASHER NUT HEX CAPSCREW IDENTlFlCATlON Shown below are actual size heads for standard screw sizes. Example: a l/4 screw has 7/16 head and thus requires a 7/16 wrench. To measure length, use the scale below. 00000 3lV Head 5/s” Head screw with screw with l/2” SD. 7ll6’S.D. 9/16” Head l/2” ...

  • Simplicity 1692243 - page 3

    TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE SEE SAE GRADE #2 0 InJLbs. In./Lbs. In.1Lb.s. FtJLbs. Nm. FtAbs. Nm. FtJLbs. Nm. 8-32 19 2.1 8-38 20 2.3 lo-24 27 3.1 lo-32 31 3.5 114-20 66 7.8 114-28 78 8.8 5118-18 11 15. 5118-24 12 18.3 318-18 20 27.2 318-24 23. 31.3 7/18-14 30. 40.8 7/16-20 35 47.8 l/2-13 50 88. l/2-20 55 74.8 9118-12 85 88.4 ...

  • Simplicity 1692243 - page 4

    SIMPLICITY MANUFACTURING, INC. FORM 1709320 500 N. Spring Street PRINTED IN U.S.A. Port Washington, Wi 53074 l/95 ...

  • Simplicity 1692243 - page 5

    TABLE OF CONTENTS SECTION Safety Rules PAGE Safe Operation Practices and Precautions ..................................................................................................... 3 Safe Operation of Snowthrower.. ................................................................................................................... .3 Safe Maint ...

  • Simplicity 1692243 - page 6

    SAFETY RULES Safe Operation Practices and Precautions Product knowledge and careful operation is the best way to prevent accidents. Read this section carefully before operating attachment system. All operators, no matter how much experience they may have, should read this and other related manuals before operating attachment system. It is the owner ...

  • Simplicity 1692243 - page 7

    8. Never attempt to make any adjustments while the engine is running (except when specifically recom- mended by manufacturer). 9. Let engine (motor) and machine adjust to outdoor temperatures before starting to clear snow. 10. Always wear safety glasses or eye shields during operation or while performing an adjustment or repair to protect eyes from ...

  • Simplicity 1692243 - page 8

    SAFETY DECALS The following safety labels are located on your tractor as shown. TO PREVENT SERIOUS INJURY, CAREFULLY READ AND FOLLOW THESE WARNING INSTRUCTIONS AT AU TIMES. THIS DECAL MUST BE POSITIONED SO AS TO BE EASILY READ FROM THE FRONT OF THE SNOWTHROWER ...

  • Simplicity 1692243 - page 9

    PARTS IDENTIFICATION TOOLS NECESSARY FOR INSTALLATION AND ASSEMBLY: One (1) l/2” Wrench Two (2) 7/l 6” Wrench One (1) 3/i&’ Allen Wrench Note: Right and left hand sides are determined by facing forward in the tractor seat. AUGER SHEAR BOLT LEVEL CHECK PLUG CUTTING EDGE AUGER SHEAR BOLT SUPPORT SPRING REDUCTION GEARBOX SKID SHOE PIN 5 ...

  • Simplicity 1692243 - page 10

    INSTALLATION Tractor Preparation 1. Increase the front tire pressure to 20 PSI for use with snowthrower. 2. On tractors with Kohler Magnum engines, loosen the air cleaner cover wing nut, pull intake hose out of plenum hole and rotate cover slightly. For winter operation only, this allows warmer air to be taken in through the air cleaner. This is no ...

  • Simplicity 1692243 - page 11

    Lift Rod 1. Lay lift rod (A, figure 3) next to the tractor so that rear clevis (B) with square weldment (C) is towards the rear. The weldment is positioned to prevent clevis pin (D) from being installed from the right hand side (interference would occur). 2. The lift rod must be inserted from the rear of the front axle, aligning rear clews (B) with ...

  • Simplicity 1692243 - page 12

    Mounting Hitch 1. Park tractor on a hard level surface. 2. Stop engine, lock parking brake, and remove key. 3. Place hitch on ground in front of tractor with pivot plate facing away from tractor. 4. Rotate the hitch attaching links rearward toward the tractor. 5. Install the back of hitch so that hitch pins (A, figure 5) are cradled in tractor hitc ...

  • Simplicity 1692243 - page 13

    Mounting Snowthrower Note: The auger blades are shipped in identical position for shipping purposes. Remove either left or right hand shear bolt (refer to figure 18 on page 14) then turn one auger 180” and reinstall shear bolt. 1. Park tractor on hard level surface. 2. Stop engine, lock parking brake and remove key. 3. Place snowthrower’s shot ...

  • Simplicity 1692243 - page 14

    14. Attach the bottom half of the spout rotator handcrank (A, figure IO) to the spiral spring shaft (B) and secure with large ring pin at location C. 15. Slide the upper half of spout rotator handcrank through the retaining bracket and into the lower half of handcrank. Secure the upper half just in front of retaining bracket with the small ring pin ...

  • Simplicity 1692243 - page 15

    A WARNING: Before operating snowthrower, make sure to position discharge chute away from people, pets, windows or other property which may be injured or damaged by snow or other thrown objects. Discharge Spout Adjustment The spout can be adjusted by loosening the knob on the left hand side and rotating spout up or down. Adjust the spout for desired ...

  • Simplicity 1692243 - page 16

    SNOWTHROWER REMOVAL Refer to figures 6-10 on pages 8-10 for removal proce- dures. 1. Park tractor on hard level surface. 2. Lower snowthrower attachment to ground. 3. Stop engine, lock parking brake, and remove key. 4. Pull coupler (A, figure 9) on snowthrower PTO shaft and disconnect from tractor’s PTO shaft. 5. Remove PTO support rod (C, figure ...

  • Simplicity 1692243 - page 17

    MAINTENANCE & STORAGE REQUIREMENTS I A WARNING Only perform maintenance inspections and proce- dures with tractor parked on hard, level surface; PTO disengaged; engine stopped; parking brake locked and key removed. Maintenance 1. Frequently check for loose or worn parts. 2. Check auger gearbox oil level every 25 hours: a. Park tractor on level ...

  • Simplicity 1692243 - page 18

    Inspecting Cutting Edge 1. Raise snowthrower to highest position. 2. Use safety block(s) to secure snowthrower: a. Place safety block under attachment. b. Lower attachment until it rests on block(s). 3. Inspect location where cutting edge (A, figure 16) meets snowthrower housing. Reversing Cutting Edge 1. Raise blower to highest position. 2. Use sa ...

  • Simplicity 1692243 - page 19

    TROUBLESHOOTING A WARNING: Only perform maintenanceinspectionsandprocedureswithtractorparkedon hard,level surface; PTO disengaged, engine stopped; parking brake locked and key removed. PROBLEM Pivot plate will not stay locked in one position. Blower does not operate at all. Auger does not rotate. Discharge fan does not rotate. Snowthrower vibrates ...

  • Simplicity 1692243 - page 20

    DRIFT CUTTER KIT, MFG. NO. 1685189 Drift cutters can be installed on left and right hand side to assist in knocking down deep snowbanks into the auger housing. It may be necessary to drill holes for installation. Follow instructions supplied with kit. Figurel8. Drift Cutters SPECIFICATIONS Cutting width: 47” Cutting height: 20” Auger diameter: ...

Manufacturer Simplicity Category Snow Blower

Documents that we receive from a manufacturer of a Simplicity 1692243 can be divided into several groups. They are, among others:
- Simplicity technical drawings
- 1692243 manuals
- Simplicity product data sheets
- information booklets
- or energy labels Simplicity 1692243
All of them are important, but the most important information from the point of view of use of the device are in the user manual Simplicity 1692243.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Simplicity 1692243, service manual, brief instructions and user manuals Simplicity 1692243. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Simplicity 1692243.

Similar manuals

A complete manual for the device Simplicity 1692243, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Simplicity 1692243 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Simplicity 1692243.

A complete Simplicity manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Simplicity 1692243 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Simplicity 1692243, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Simplicity 1692243, that we can find in the current document
3. Tips how to use the basic functions of the device Simplicity 1692243 - which should help us in our first steps of using Simplicity 1692243
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Simplicity 1692243
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Simplicity 1692243 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Simplicity 1692243?

Use the form below

If you did not solve your problem by using a manual Simplicity 1692243, ask a question using the form below. If a user had a similar problem with Simplicity 1692243 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)