English dropdown-ico

Manual Toshiba B-8204-QM-R

22 pages 0.87 mb
Download

Go to site of 22

Summary
  • Toshiba B-8204-QM-R - page 1

    - 1 - Rotary Cutter Module B-8204-QM-R Installation Manual 1. APPLICABLE MODEL This optional kit is the rotary cutter module, which is intended for the following models: B-SX4T Series, B-SX5T Series NOTE: When using the Rotary Cutter to the B-SX4T Series, be sure to install the Ribbon Saving Module (B-9904-R/R2-QM). Failure to do this may cause a p ...

  • Toshiba B-8204-QM-R - page 2

    - 2 - 3) Remove the four B-4x5 screws from the side panel (L). 4) Open the top cover and remove the three P- 4x8 screws that secure the side panel (L). 5) Lift the side panel (L) and put it aside. 6) Disconnect the fan motor harness from CN19 on the Main PC board, and then separate the side panel (L). 7) Fix the cutter drive unit to the printer wit ...

  • Toshiba B-8204-QM-R - page 3

    - 3 - 8) Connect the 9-pin connector of the harness ass’y to CN7 and 2-pin connector to CN9 on the cutter driver unit, respectively. 9) Fit the bush to the harness ass’y in the orientation as shown below. 10) Insert the harness ass’y into the hole in the main frame. Fit the bush into the hole. CN7 (9 pins) CN9 (2 pins) Harness Ass’y Bush Ha ...

  • Toshiba B-8204-QM-R - page 4

    - 4 - 11) Fix the harness ass’y with the clamp. 12) Connect the 9-pin connector of the harness ass’y to CN15, and 2-pin connector to CN18 on the Main PC board, respectively. 13) Turn the head lever counterclockwise to Free position. 14) Open the ribbon shaft holder plate. 15) Raise the print head block until it stops. Main PC Board Clamp Ribbon ...

  • Toshiba B-8204-QM-R - page 5

    - 5 - 16) Connect the four harnesses of the cutter unit to CN8, CN10, CN11 and CN12 on the cutter drive unit. 17) Fit the two tabs of the cutter drive unit into the notches, and then fix the cutter unit with the three SM-4x8 screws. Cutter Unit Cutter Drive Unit Print Head Block Cutter Unit CN8 CN12 CN10 CN11 SM-4 x 8 Screw Notch Tab Notch Tab SM-4 ...

  • Toshiba B-8204-QM-R - page 6

    - 6 - 18) Attach the cutter cover to the cutter unit with the two screws so that the tab of the cutter cover turns on the cutter cover open switch. NOTES: 1. Be careful not to pinch the cutter harness by the cutter cover. 2. Make sure that the anti-static brush is protruding from the media outlet. 19) Close the print head block and ribbon shaft hol ...

  • Toshiba B-8204-QM-R - page 7

    - 7 - 3.2 Installing the Rotary Cutter Unit on the B-SX5T Series Since the strip module is st andard on the B-SX5T series, it is necessary to remove the rewinder guide plate, strip sensor, etc. before in stalling the cutter module. 1) Turn the power off and disconnect the power cord. 2) When the printer is used in the batch or strip mode: Remove th ...

  • Toshiba B-8204-QM-R - page 8

    - 8 - 5) Lift the side panel (L) and put it aside. 6) Disconnect the fan motor harness from CN19 on the Main PC board, and then separate the side panel (L). 7) Remove the SM-4x8 screw that secures the operation panel ass’y. 8) Half open the top cover, otherwise the operation panel ass’y cannot be removed from the printer. 9) Lift the operation ...

  • Toshiba B-8204-QM-R - page 9

    - 9 - 10) Disconnect the operation panel harness from the operation panel ass’y. 11) Turn the head lever clockwise to Free position. 12) Open the ribbon shaft holder plate. Operation Panel Ass’y Ribbon Shaft Holder Plate Operation Panel Harness Hook Head Leve r Free position Lock position (Label) Lock position (Tag) ...

  • Toshiba B-8204-QM-R - page 10

    - 10 - 13) Raise the print head block until it stops. 14) Remove the two SMW-4x8 screws that se cure the strip sensors (TR) and (LED). 15) Release the strip sensor (LED) har ness from the cable clamp, and disc onnect it from the shorter harness of the strip sensor harness (TR). Print Head Block Stoppe r SMW-4x8B Screw Strip Sensor (Tr) SMW-4x8B Scr ...

  • Toshiba B-8204-QM-R - page 11

    - 11 - 16) Remove the Expansion I/O board from the prin ter temporarily using the following procedure. (1) Disconnect the Expansion I/O cable from CN1 on the Expansion I/O board. (2) Remove the two B-3x6 screws to detach the Expansion I/O board from the printer. 17) Disconnect the shorter harness of t he strip sensor harness (TR) from CN20 on the M ...

  • Toshiba B-8204-QM-R - page 12

    - 12 - 20) Fix the cutter drive unit to the printer with the three SM-4x8 screws. 21) Connect the 9-pin connector of the harness ass’y to CN7 and 2-pin connector to CN9 on the cutter driver unit, respectively. 22) Fit the bush to the harness ass’y in the orientation as shown below. 23) Insert the harness ass’y into the hole in the main frame. ...

  • Toshiba B-8204-QM-R - page 13

    - 13 - 24) Fix the harness ass’y with the clamp. 25) Connect the 9-pin connector of the harness ass’y to CN15, and 2-pin connector to CN18 on the Main PC board, respectively. 26) Connect the four harnesses of the cutter unit to CN8, CN10, CN11 and CN12 on the cutter drive unit. Main PC Board Clamp Cutter Unit Cutter Drive Unit CN18 (2 pins) CN1 ...

  • Toshiba B-8204-QM-R - page 14

    - 14 - 27) Fit the two tabs of the cutter drive unit into the notches, and then fix the cutter unit with the three SM-4x8 screws. 28) Attach the cutter cover to the cutter unit with the two screws so that the tab of the cutter cover turns on the cutter cover open switch. NOTES: 1. Be careful not to pinch the cutter harness by the cutter cover. 2. M ...

  • Toshiba B-8204-QM-R - page 15

    -15 - ロータリーカッターモジュール(B-8204-QM-R) 組込説明書 このたびは「ロータリーカッターモジュール B-8204-QM-R」をお買い上げいただき、誠にありがとうございます。 B-8204-QM-R は、B-SX5T-R シリーズ用のロータリー式カッターモジュールです。 B-8204-QM-R を組み込 ...

  • Toshiba B-8204-QM-R - page 16

    -16 - ■ 組込手順 1) プリンタの電源スイッチを OFF にし、電源プラグをコンセ ントから抜きます 。 2) 用紙発行口下側の黒い化粧ネジ２本を外し、目隠し 板を取り外します。 補足 目隠し板および化粧ネジは、 紛失しないよう大切に 保管してください。 3) 左サ? ...

  • Toshiba B-8204-QM-R - page 17

    -17 - 7) ヘッドレバーを Free の位置まで回します。 8) リボンシャフト固定板を静か に右側へ倒します。 9) 印字ヘッド機構部を持ち上げてロ ックします。 10) セムスネジ(SM-4x8)３本で、カッ ター制御部を印字ヘッド 機構部の下に取り付けます。 リボンシャフト固 ...

  • Toshiba B-8204-QM-R - page 18

    -18 - 11) カッターケーブルをカッター制御部の CN7 と CN9 へ接続します。 12) カッターケーブルにコードブッシュを取り 付けます。 13) カッターケーブルをメインフレーム下側の丸穴に通し、コード ブッシュをはめ込みます。 CN7 (9 ﾋﾟﾝ ) CN9 (2 ﾋﾟﾝ ) カッター ...

  • Toshiba B-8204-QM-R - page 19

    -19 - 14) コードクランプでカッターケーブルを止め、Main PC 板の CN15 と CN18 へカッターケーブル を接続します。 15) カッター機構部の４本のコネクタケ ーブルを、カッター制御部の CN8,CN10, CN11 および CN12 へ接続し ます。 Main PC 板 ケー ブ ル クランプ カッター ? ...

  • Toshiba B-8204-QM-R - page 20

    -20 - 16) カッター制御部の２つの突起部とカッ ター機構部の角穴を合わせ、セム スネジ(SM-4x8)３ 本でカッター 機構部を固定します。 補足 ケー ブル類をかまないよ うに、カッター機構部を固定し てください。 17) カッターカバーを取り付け、カバーに付いて ? ...

  • Toshiba B-8204-QM-R - page 21

    -21 - 18) 印字ヘッド機構部のロック を解除して静かに下ろ し、リボンシ ャフト固定板を閉め ます。 19) 冷却 ファンケーブルを接続し、左サイドカバーを取り付けます。 補足 ケーブル類をかまないよ うに、左サイドカバー を確実に取り付けてください 。 20) ? ...

  • Toshiba B-8204-QM-R - page 22

    FMMB0067606 Printed in Japan EO2-38009F Ⓒ東芝テック株式会社 2008 ...

Manufacturer Toshiba Category Brush Cutter

Documents that we receive from a manufacturer of a Toshiba B-8204-QM-R can be divided into several groups. They are, among others:
- Toshiba technical drawings
- B-8204-QM-R manuals
- Toshiba product data sheets
- information booklets
- or energy labels Toshiba B-8204-QM-R
All of them are important, but the most important information from the point of view of use of the device are in the user manual Toshiba B-8204-QM-R.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Toshiba B-8204-QM-R, service manual, brief instructions and user manuals Toshiba B-8204-QM-R. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Toshiba B-8204-QM-R.

Similar manuals

A complete manual for the device Toshiba B-8204-QM-R, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Toshiba B-8204-QM-R by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Toshiba B-8204-QM-R.

A complete Toshiba manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Toshiba B-8204-QM-R - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Toshiba B-8204-QM-R, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Toshiba B-8204-QM-R, that we can find in the current document
3. Tips how to use the basic functions of the device Toshiba B-8204-QM-R - which should help us in our first steps of using Toshiba B-8204-QM-R
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Toshiba B-8204-QM-R
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Toshiba B-8204-QM-R in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Toshiba B-8204-QM-R?

Use the form below

If you did not solve your problem by using a manual Toshiba B-8204-QM-R, ask a question using the form below. If a user had a similar problem with Toshiba B-8204-QM-R it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)