English dropdown-ico

Manual Regency E33-LP

32 pages 3.55 mb
Download

Go to site of 32

Summary
  • Regency E33-LP - page 1

    FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. 6988 V enture St., Delta, BC, Canada V4G 1H4 918-408 W ARNING: Improper installation, adjustment, alteration, service or main- tenance can cause injury , property damage, or loss of life. Refer to this manual. For assistance or additional informa- tion consult an authorized installer , service agency or t ...

  • Regency E33-LP - page 2

    2 E33 FPI Direct V ent Gas Insert FPI GAS FIREPLACE INSERT TO THE NEW OWNER Congratulations! Y ou are the owner of a state-of-the-art Gas Insert by FPI. The E33 Gas Insert has been designed to provide you with all the warmth and charm of a fi replace, at the fl ick of a switch. The E33-NG and E33-LP have been approved by Warnock Hersey for both s ...

  • Regency E33-LP - page 3

    3 E33 FPI Direct V ent Gas Insert T ABLE OF CONTENTS FPI GAS FIREPLACE INSERT OPERA TING INSTRUCTIONS First Fire ........................................................................ 18 Operating Instructions .......................................................... 18 Lighting Procedure ......................................................... ...

  • Regency E33-LP - page 4

    4 E33 FPI Direct V ent Gas Insert SAFETY LABEL This is a copy of the labels that accompany each E33 Gas Insert. We have printed a copy of the contents here for your review . The safety label is located on a plate inside the base of the unit visible when the bottom louver is opened. Ensure that the safety label is attached to the unit. NOTE: FPI uni ...

  • Regency E33-LP - page 5

    5 E33 FPI Direct V ent Gas Insert IMPORT ANT : SA VE THESE INSTRUCTIONS The FPI Gas Fireplace must be installed in accordance with these instructions. Carefully read all the instructions in this manual fi rst. Consult the building authority having jurisdic- tion to determine the need for a permit prior to starting the installation. NOTE: Failure t ...

  • Regency E33-LP - page 6

    6 E33 FPI Direct V ent Gas Insert 14) Install optional Excalibur Surround. See page 15. 15) Install optional remote control or wall ther- mostat, pages 17. 16) Final check (page 18): Before leaving this unit with the customer , the installer must ensure that the appliance is fi ring correctly . This includes: a) Clocking the appliance to ensure th ...

  • Regency E33-LP - page 7

    7 E33 FPI Direct V ent Gas Insert MINIMUM CLEARANCES T O COMBUSTIBLES From Unit Side W alls * A 8" (203 mm) Ceiling B 47" (1 194 mm) Min. Mantel Height C 15" (381 mm) Max. Mantel Depth D 3-1/2" (89 mm) Alcove Width E 76" (1930 mm) Alcove Depth F 36" (914 mm) Hearth Height G 1-1/4" (32 mm) Hearth Width H 45-1/2&quo ...

  • Regency E33-LP - page 8

    8 E33 FPI Direct V ent Gas Insert VENTING THE APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY FLUE SERVING A SEP ARA TE SOLID FUEL BURNING APPLIANCE. This appliance is designed to be attached to two 3" (76mm) co-linear aluminium fl ex running the full length of the chimney . The fl ue length must be a minimum length of 8 ' (2.44m) and a ma ...

  • Regency E33-LP - page 9

    9 E33 FPI Direct V ent Gas Insert OPTIONAL BRICK P ANEL Optional Brick Panel Set: Part # Description Qty T op (brick) panel 1 Back (brick) panel 1 Left (brick) panel 1 Right (brick)panel 1 340-043 T op bracket 1 340-094 Bottom clips 2 51 1-031 Brick clips 2 Diagram 1 GAS PIPE PRESSURE TESTING The appliance must be isolated from the gas supply pipin ...

  • Regency E33-LP - page 10

    10 E33 FPI Direct V ent Gas Insert T op Bracket 5) Place the top bracket onto the top edge of the top panel (refer to Diagram 2). Diagram 2 6) Slide the top panel and bracket assembly carefully onto the baffl e plate ensuring the panel is centered. Make sure the tabs of the top bracket fi t into the baffl e openings (refer to Diagram 3). 7) Inse ...

  • Regency E33-LP - page 11

    11 E33 FPI Direct V ent Gas Insert INST ALLA TION 5) Re-install the grate (reverse step 3). 6) Line up the pin holes (located at the bottom of log 03-23 ) to the pins of the rear log sup- port and position them into place. (refer to Diagram 3) Diagram 3 03-23 Locating Pins 03-23 03-17 03-21 Diagram 5 7) Align the bottom grooves of log 03-21 onto th ...

  • Regency E33-LP - page 12

    12 E33 FPI Direct V ent Gas Insert INST ALLA TION Final Installation 03-19 E33 CONVERSION KIT FROM NG T O LPG THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! Conversion Kit Contains: Qty . Part # Description 1 910-018 SIT Conversion Kit-50% T urndown LPG 1 910-037 LPG (Pilot Orifi ce) 1 904-641 Burne ...

  • Regency E33-LP - page 13

    13 E33 FPI Direct V ent Gas Insert Diagram 4 INST ALLA TION 9) Attach the trim to the faceplate by using the plated screws (refer to Diagram 4). Rear V iew: Faceplate Assembly Diagram 1 F ACEPLA TE & TRIM INST ALLA TION 1) Lay the faceplate panels fl at, face down on something soft so they don't scratch. 2) T ake the top faceplate and ali ...

  • Regency E33-LP - page 14

    14 E33 FPI Direct V ent Gas Insert INST ALLA TION Diagram 5 11 ) Push the FPI logo plate into the two holes in the bottom left corner of the faceplate. The standard fl ush door comes with a black frame. T o install the frame, simply hook the top door fl ange onto the top of the unit and swing the door towards the unit, (Diagram 1 and 2). Be caref ...

  • Regency E33-LP - page 15

    15 E33 FPI Direct V ent Gas Insert 1) Align the left side Faceplate T rim Bracket with the Firebox Flange and secure using 2 screws as shown in diagram 1. Repeat for right side. Faceplate T rim Bracket Firebox Flange IMPORT ANT NOTE: When using the Surround, the unit must be set 1" further into the fi replace than the standard face- plate ins ...

  • Regency E33-LP - page 16

    16 E33 FPI Direct V ent Gas Insert INST ALLA TION 1) Remove the rivets from the surround by pulling off the hoseclamp (located at the backside of surround) with a screwdriver or plyer . Re-install the rivets by putting them through the holes on the sides of the sur- round. 3) Remove the handles by removing the nut and screw . Install the new handle ...

  • Regency E33-LP - page 17

    17 E33 FPI Direct V ent Gas Insert WIRING DIAGRAM INST ALLA TION This heater does not require a 120V A.C. supply for operation. However , a 120V A.C. power sup- ply is needed for the fan/blower operation. W ARNING: Electrical Grounding Instructions This appliance is equipped with a three pronged (grounding) plug for your protection against shock ha ...

  • Regency E33-LP - page 18

    18 E33 FPI Direct V ent Gas Insert OPERA TING INSTRUCTIONS 2) T urn gas control knob so indicator points to "OFF" position and allow 5 minutes for any gas in the combustion chamber to escape. 3) Turn gas control knob counterclockwise so indicator points to the "PILOT" position. Depress the gas control knob fully . Depress the ig ...

  • Regency E33-LP - page 19

    19 E33 FPI Direct V ent Gas Insert OPERA TING INSTRUCTIONS COPY OF LIGHTING INSTRUCTION PLA TE AUT OMA TIC CONVECTION F AN OPERA TION The fan operates automatically . T urn the knob on the side of the faceplate to adjust to the desired speed. The fan will turn on as the stove comes up to operating temperature. After the unit has been turned off and ...

  • Regency E33-LP - page 20

    20 E33 FPI Direct V ent Gas Insert MAINTENANCE GENERAL VENT MAINTENANCE Conduct an inspection of the venting system semi-annually . Recommended areas to inspect as follows: 1) Check the V enting System for corrosion in areas that are exposed to the elements. These will appear as rust spots or streaks, and in extreme cases, holes. These com- ponents ...

  • Regency E33-LP - page 21

    21 E33 FPI Direct V ent Gas Insert MAINTENANCE F AN MAINTENANCE If your fan requires maintenance or replace- ment, access to the fan is through the plate on the fl oor of the fi rebox. NOTE: the unit MUST NOT be operated without the fan access panel securely in place. Caution: Label all wires prior to discon- necting when servicing controls. Wiri ...

  • Regency E33-LP - page 22

    22 E33 FPI Direct V ent Gas Insert MAINTENANCE 11 ) Disconnect the inlet gas line. 12) Unplug the black and red wires at the valve. Undo the 2 TP wires at the valve. 13) Remove the 17 screws on the valve tray . 14) T ake out the valve tray from the unit. 15) Scrape of f the old gasket from the fl oor of the fi rebox and from the valve access plat ...

  • Regency E33-LP - page 23

    23 E33 FPI Direct V ent Gas Insert P ARTS LIST MAIN ASSEMBL Y Part # Description 1) 340-038 Fan Access Plate 2) 340-103 Gasket - Fan Access Plate 3) 320-517/P Fan Assembly 120 V 910-331/P Fan Motor 120 V 5) 910-750 Power Cord 910-752 Wire Harness (Faceplate) 910-692 Wire Fan to Power Cord 910-737 Wire V alve to Spill Switch 7) 910-142 Fan Auto On/O ...

  • Regency E33-LP - page 24

    24 E33 FPI Direct V ent Gas Insert P ARTS LIST BURNER & LOG ASSEMBL Y Part # Description 52) 340-104 Gasket - V alve Tray 340-574/P V alve Assembly - NG 340-576/P V alve Assembly - LP 56) 910-190 Piezo Ignitor and Nut 57) 910-378 V alve - S.I.T . - Natural Gas 910-380 V alve - S.I.T . - Propane 59) * V alve Tray 910-034 Pilot Assy-3 Flame Conv ...

  • Regency E33-LP - page 25

    25 E33 FPI Direct V ent Gas Insert 83 84 85 86 87 88 88 88 88 89 90 90 FULL SCREEN FRONT INST ALLA TION Part # Description P ARTS LIST 83) T op Frame 84) 340-910 Full Screen Door - Black 85) Full Screen Left Door 86) Full Screen Right Door 87) Bottom Frame 88) Screw #8 x 1/2 Self T apping 89) 910-199 Wire Clip Holder 90) 948-042 Hinge Spring ...

  • Regency E33-LP - page 26

    26 E33 FPI Direct V ent Gas Insert P ARTS LIST F ACEPLA TES, TRIMS AND HEARTHS Part # Description Part # Description 340-918 Fa ceplates and T rim (Complete) with Black Tr i m 340-919 Oversized Faceplate 74) 904-569 Fan Speed Control Knob 91) * Faceplate Side - Right 92) * Faceplate - T op 93) * Faceplate Side - Left Assy 340-532 T rim Set Packaged ...

  • Regency E33-LP - page 27

    27 E33 FPI Direct V ent Gas Insert NOTES ...

  • Regency E33-LP - page 28

    28 E33 FPI Direct V ent Gas Insert NOTES ...

  • Regency E33-LP - page 29

    29 E33 FPI Direct V ent Gas Insert NOTES ...

  • Regency E33-LP - page 30

    30 E33 FPI Direct V ent Gas Insert ...

  • Regency E33-LP - page 31

    31 E33 FPI Direct V ent Gas Insert W ARRANTY FPI Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T eam carefully inspects each unit thoroughly before it leaves our facility . FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime warranty to the origi ...

  • Regency E33-LP - page 32

    32 E33 FPI Direct V ent Gas Insert Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ________________________________________ ...

Manufacturer Regency Category Stove

Documents that we receive from a manufacturer of a Regency E33-LP can be divided into several groups. They are, among others:
- Regency technical drawings
- E33-LP manuals
- Regency product data sheets
- information booklets
- or energy labels Regency E33-LP
All of them are important, but the most important information from the point of view of use of the device are in the user manual Regency E33-LP.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Regency E33-LP, service manual, brief instructions and user manuals Regency E33-LP. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Regency E33-LP.

Similar manuals

A complete manual for the device Regency E33-LP, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Regency E33-LP by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Regency E33-LP.

A complete Regency manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Regency E33-LP - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Regency E33-LP, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Regency E33-LP, that we can find in the current document
3. Tips how to use the basic functions of the device Regency E33-LP - which should help us in our first steps of using Regency E33-LP
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Regency E33-LP
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Regency E33-LP in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Regency E33-LP?

Use the form below

If you did not solve your problem by using a manual Regency E33-LP, ask a question using the form below. If a user had a similar problem with Regency E33-LP it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)