English dropdown-ico

Manual Siemens CL-010

104 pages 3.38 mb
Download

Go to site of 104

Summary
  • Siemens CL-010 - page 1

    CL -010/CL -010- I ADSL2+ R outer User’s Manual R ev: 1.5 2007/03/30 No part of this publication may be re produced in any form by any means with out the prior written per mi ss ion. Other trademarks or brand names mentioned here in ar e trademarks or registered tradem arks of their respective companies. This manual currently suits for CL -010/CL ...

  • Siemens CL-010 - page 2

    Safety Notes For Installation  Use only the type of power source indicated on the marking labels.  Use only power adapter supplied with th e produ ct.  Do not overload wall outlet or extension co rds as th is may increase the risk of electric shock or fire. If t he power cord is frayed, replace it with a new one.  Proper ventilation is ...

  • Siemens CL-010 - page 3

    ADSL Router User Manual FCC FCC Class B Notice This device complies with Part 15 of the FCC Rules. Operation is subject to th e fo llowing two conditions: (1) this de vice may not cau se harmful inter ference, and (2) this device m ust accept any interference received, including i nterference that m ay cause undesired operation. Note: This equipmen ...

  • Siemens CL-010 - page 4

    Preface Thank you for choosing the Asymmetric Digital Subsc riber Line (ADSL 2+) Router . W ith the asymmetric technology , t his device runs over st andard co pper phone lines. In addition, ADSL2+ allows you to have both voi ce and data ser vi ces in use sim ultaneously a ll over one phon e line. CL-010/CL-0 10-I ADSL2+ Router is a DSL broadba nd ...

  • Siemens CL-010 - page 5

    ADSL Router User Manual ³ RFC2684 LLC Encapsulation and VC Multiplexing over AAL5 ³ RFC2364 Poin t -t o-P oi nt Pr ot ocol (PPP) over AAL5 ³ RFC2225 Classical IP and ARP over A TM ³ RFC2516 PP P over Et hernet: support Relay (T ra nsparent For warding and Client functi ons) ³ Support PPPo A or PP PoE Bridged m ode (the IP address got from ISP ...

  • Siemens CL-010 - page 6

    ³ Firmware upgrades through HTTP , TFTP , or FTP ³ The boot l oader contains ve ry simpl e web page to all ow the users to update the ru n-time firmware image. ³ Configuration file backup and restore ³ SNMPv1/v2 agent with MIB-II, ADSL Line MIB Unpacking Check the contents of the package against the pack contents checklist below . If any of the ...

  • Siemens CL-010 - page 7

    ADSL Router User Manual Subscription for ADSL Se rvice T o use the ADSL Router , you have to subscribe for ADSL service from your broadband serv ice provider . According to the service type you su bscribe, you will get va rious IP addresses: Dynamic IP: If you apply for dial-up connection , you will be given an Internet account with username and pa ...

  • Siemens CL-010 - page 8

    ...

  • Siemens CL-010 - page 9

    Chapter 1: Overview Chapter 1: Overview This chapter provides you t he description for the LED and con nector for front a nd rear view of the router . Before you use/install t hi s rout er , pl ease take a look at this information first. Physical Outlook Front Panel The following illustrations show the front panel of the ADSL Router: LED Indicators ...

  • Siemens CL-010 - page 10

    Rear Panel The following figures illustrate the rear panel of your ADSL Router . Connector Description 9V AC 9 VAC P ower connector P ower switch Ethernet Ethernet RJ-45 connector DSL RJ-11 connector 9 V A C ...

  • Siemens CL-010 - page 11

    Chapter 2:System Requir ement and Installation C h a p t e r 2 : System Requirement and Installation System Requirement T o access the ADSL R outer via Ethernet, the host com puter must meet the following re quirements:  W ith Ethe rnet network i nterface.  Must have TCP/IP inst alled.  Set client PC with obtain an IP address automatically ...

  • Siemens CL-010 - page 12

    Connecting the ADSL Router Follow the steps below to connect the related devices. n Connecting the ADSL line. Connect the DSL port of the device to your ADSL wall outlet with RJ-1 1 cable. o Please attach one end of the Ethernet cable with RJ-45 connector to the LAN port of y our ADSL R outer . p Connect the other end of the cable to the Ethernet p ...

  • Siemens CL-010 - page 13

    Chapter 3: Configuratio n For connecting throu gh a hub, please refer to the following diagram for a n example. 9 VA C Setting TCP/IP In order t o access the Internet t hrough the rout er , each host on your networ k must install/setup TCP/IP . Please follow th e steps below for select a network adapter . ...

  • Siemens CL-010 - page 14

    For Windows 98 1. Click on the St a rt menu, poi nt to Settings and click on Control P anel . 2. Double-click the Network ic on 3. The Network window ap pears. On the Configuration tab, check out the list of installed network components. Option 1: If y ou have no TC P/IP protocol , click Add . Option 2: If y ou have TCP/IP protocol, go to St ep 6 Y ...

  • Siemens CL-010 - page 15

    Chapter 3: Configuratio n 5. On the left side of the windows, highlight Micr osoft and then select TCP/IP on the right side. Then click OK 6. When returni ng to Netw ork window , highlight TCP/I P protocol f or your NIC and click Pr operties . 7. On IP Addr ess tab: Enable Specify an IP address option. Enter the IP Addr ess : 192.168.1.x (x is betw ...

  • Siemens CL-010 - page 16

    8. When returni ng to Netw ork window , click OK 9. W ait for W indows copying files. 10. When p rom pted with System Setti ngs Change dialog box, click Ye s to restart your computer . ...

  • Siemens CL-010 - page 17

    Chapter 3: Configuratio n For Windows ME 1. Click on the Start menu, poi nt to Settings and click on Control Panel . 2. Double-click the Network ic on. 3. The Network window ap pears. On the Configuration tab, check out the list of installed network components. Option 1: If y ou have no TC P/IP protocol , click Add . Option 2: If y ou have TCP/ IP ...

  • Siemens CL-010 - page 18

    9. Wait for Windows copying files. 10. When prompted with the System Settings Chan ge dialog box, click Yes to restart your computer. For Windows NT 1. Click Start , point to Settings , and then click Control Pa nel . 2. Double-click the Network ic on. 3. The Network window ap pears. On the Protocols tab, check out the list of installed network com ...

  • Siemens CL-010 - page 19

    Chapter 3: Configuratio n 5. Click Yes to use DHCP. 6. Insert the Windows NT CD into your CD-ROM drive and type the location of the CD. Then click Continue . 7. Returning to the Network window, you will find the TCP/IP Protocol among the list. Select TCP/IP Protocol and click Properties . 8. Enable Specify an IP address option. Enter the IP Address ...

  • Siemens CL-010 - page 20

    9. When returni ng to Netw ork window, click Close . 10. When p rom pted with Netw ork Settings Chan ge dialog box, click Yes to restart your computer. ...

  • Siemens CL-010 - page 21

    Chapter 3: Configuratio n For Windows 2000 1. From the Start menu, point to Settings and then clic k Network an d Dial-up Connections. 2. Right-cl ick the Local Area Connection icon and t hen click Properties . 3. On the Gener al tab, check out the list of installed network com ponents. Option 1: If y ou have no TC P/IP Protocol , click Install . O ...

  • Siemens CL-010 - page 22

    4. Highli ght Protocol and then click Add . 5. Click Int ernet Protoc ol (TCP/IP) an d then click OK. 6. When returni ng to Local Area Connection Properties window, highlight I nte r net Prot ocol (TCP/IP) and then click Properties. 7. Under the General tab, enable Use t he following IP Address . Enter the IP address : 192.168.1.x (x is bet ween 2 ...

  • Siemens CL-010 - page 23

    Chapter 3: Configuratio n For Windows XP From the Start menu, point to Control Panel and then click Network and Internet Connections . Click Network Connection and then click Properties . Click Network Connection and then click Properties .3.On the General tab, check out the list of installed network component s. Option 1: If y ou have no TC P/IP P ...

  • Siemens CL-010 - page 24

    For Windows Vista 8. Open the Start menu, point to Control Panel and click it. 9. Click Network and Internet. 10. Select Networ k and Sharing Center . ...

  • Siemens CL-010 - page 25

    Chapter 3: Configuratio n 11. Click Manage Netw ork Connection on the left side. 12. Right click Local A rea Connection and select Properties . 13. On the Ne tworking tab, you will find Internet Protocol Version 6 and Vers ion 4. Contact your ISP to confirm which one will be used. (We take TCP/IPv4 for example here.) Select Internet Protoc ol Versi ...

  • Siemens CL-010 - page 26

    14. Unde r the General tab, enable Use the fo llo wing IP address . Enter the IP address : 192.168.1.x (x is between 2 and 254 ), Sub net Mask : 255.255.255 .0 and Default gateway : 192.168.1.1 . Then click Ok. Renewing IP Address on Client PC After the ADSL Router gets on lin e, there is a chance that your PC does not renew its IP address and thus ...

  • Siemens CL-010 - page 27

    Chapter 3: Configuratio n On the IP Address tab, select Obtain an IP address automatically . The n click OK . For Windows ME On the IP Address tab, select Obtain an IP address automatically . The n click OK . ...

  • Siemens CL-010 - page 28

    For Windows NT On the IP Address tab, click on the drop-down arrow of Adapter to select requir ed adap ter. En able Obtain an IP address from a DHCP server and then click OK .. When prompted with the message below, click Yes to continue. For Windows 2000 Enable Obtain an IP ad dress automatically and then click OK. ...

  • Siemens CL-010 - page 29

    Chapter 3: Configuratio n For Windows XP On the IP Address tab, select Obtain an IP address automatically . The n click OK . Windows Vista On the IP Address tab, select Obtain an IP address automatically . The n click OK . ...

  • Siemens CL-010 - page 30

    Renew IP Address on Client PC There is a chance that your PC does not renew its IP address after the ADSL Router is on line and the PC cannot access the Internet. Please fol low the procedures bel ow to renew PC’ s IP address . For Windows 98ME 1. Select Run from the Start menu. 2. Type winipcfg in the dialog box a nd the click OK . 3. When the f ...

  • Siemens CL-010 - page 31

    Chapter 3: Configuratio n 2. Select Run from the Start menu. 3. Type cmd in the dialog box a nd the click OK . 4. Type ipconfig at prompt. Then you will see the IP information from DHCP server. 5. If you wa nt to get a new IP address, type ipconfig /release to release the previous IP address and then type ipconfig /renew to get a new one. ...

  • Siemens CL-010 - page 32

    For Windows 2000 1. From the Star t menu, point to Programs , Accessories a nd then click Command Prompt . 2. Type ipconfig at prompt. Then you will see the IP information from DHCP server. 3. If you wa nt to get a new IP address, type ipconfig /release to release the previous IP address and then type ipconfig /renew to get a new one. For Windows X ...

  • Siemens CL-010 - page 33

    Chapter 3: Configuratio n For Windows Vista 1. Open the Start menu, and type cmd in the text box then click OK . 2. The comm and prompt window will appear. 3. Type ipconfig at the command win dow a n d pres s Enter to view the computer’s IP information from DHCP server. 4. If the com puter is hol ding a current IP address, type ipconfig /release ...

  • Siemens CL-010 - page 34

    Note: If you cannot release the IP address successfully and see the message “ The requested operation requires elevation ,” please go to the Start m enu and right click Command Prompt , then set Run as administrator . Press Continue when a dialog asking for perm issi on to co nt i nue prompt s. After then, repeat the above instruction to releas ...

  • Siemens CL-010 - page 35

    Chapter 3:Connecting and Ac cessing Internet C h a p t e r 3 : Connecting and Accessing Internet This chapter is to help you accessin g into Internet with a quick and conv enient way . If you need more detailed information for web configur ation, please get into the next chapter for the advanced configuration. Prior to configuring the ADSL Router , ...

  • Siemens CL-010 - page 36

    PPP over ATM (PPPoA) Mode RDAIUS Server AAA BRAS STM-1 DSLAM Loop Dynamic Public IP assigned by BRAS PPPoA+NAT+DHCP on Private LAN Hub ADSL Router Ethernet PC(S) 192.168.1.3 192.168.1.2 PPP over ATM Default Private IP 192.168.1.1 ISP (Internet S ervice Provider) *BRAS: Broadband Remote Access Server Description: In this depl oyment environm ent, th ...

  • Siemens CL-010 - page 37

    Chapter 3:Accessing Internet PPP over ATM (PPPoA) IP Extension Mode RDAIUS Server AAA BRAS STM-1 DSLAM Loop PPPoA+NAT+DHCP on Private LAN Hub ADSL Router Ethernet PC PPP over ATM Default Private IP 192.168.1.1 ISP (Internet S ervice Provider) *BRAS: Broadband Remote Access Server Dynamic Public IP assigned by BRAS Description: In this depl oyment e ...

  • Siemens CL-010 - page 38

    PPP over Ethernet (PPPoE) Mode RDAIUS Server AAA BRAS STM-1 DSLAM Loop Dynamic Public IP assigned by BRAS PPPoE+NAT+DHCP on Private LAN Hub ADSL Router Ethernet PC(S) 192.168.1.3 192.168.1.2 PPP over Ethernet Default Private IP 192.168.1.1 *BRAS: Broadband Remot e Acce ss Serv er ISP (Internet Service Provider) Description: In this depl oyment envi ...

  • Siemens CL-010 - page 39

    Chapter 3:Accessing Internet PPP over Ethernet (PPPoE) IP Extension Mode RDAIUS Server AAA BRAS STM-1 DSLAM Loop Dynamic Public IP assigned by BRAS P P P o E I P Extension Mode Hub ADSL Router Ethernet PC(S) PPP over Ethernet Default Private IP 192.168.1.1 *BRAS: Broadband Remot e Access Server ISP (Internet Service Provider) Description: In this d ...

  • Siemens CL-010 - page 40

    Numbered IP over ATM (IPoA) RDAIUS Server AAA BRAS STM-1 DSLAM Loop Public IP Pre-assigned b y I S P Hub ADSL Router PC(S) IP over ATM S/W Default Privat e IP 192.168.1 .1 *BRAS: Broadband Rem o te Acc es s Ser ve r ISP (Inter n et Servi ce Prov i der) 10.3.75.49 1 0.3.75.51 10.3.75.50 10.3.70.1 Description: If you apply for multiple IP addresses f ...

  • Siemens CL-010 - page 41

    Chapter 3:Accessing Internet 7. Check the network information. Make sure the setting s match th e settings provided by ISP . Click Finish . 8. Set TCP/IP for your computer . Specify an IP Addr ess, subnet mask and set default gateway . eg: IP Address: 10 .3.75.51 Subnet Mask: 255.255.255.248 Gateway: 10. 3 .7 5. 49 9. Now the router is well configu ...

  • Siemens CL-010 - page 42

    Numbered IP over ATM (IPoA)+NAT Description: In this depl oyment envi ronment, we m ake up a private IP network of 192. 168.1.1. N A T funct ion is enabled (on ADSL Router or use another NA T box connected to hub) to suppo rt multiple clients to access the Router and some public se rvers (WWW , FTP). If you apply for multiple IP addresses from your ...

  • Siemens CL-010 - page 43

    Chapter 3:Accessing Internet LAN. Primary IP Addr ess : 192.168.1.1 Subnet mask : 255.255.255.0 S tart IP Address: 192.168.1.2 End IP Address: 192.168.1.254 7. Check Configure the sec ond IP Address and Subne t Mask for L AN Interface and type i n the second IP address and subnet mask. Then click Ne xt . Secondary IP Addr ess : 10.3.75.49 Subnet ma ...

  • Siemens CL-010 - page 44

    Unnumbered IP over ATM (IPoA) RDAIUS Server AAA BRAS STM-1 DSLAM Loop Public IP Pre-assigned b y I S P Hub ADSL Router PC(S) IP over ATM S/W Default Private IP 192.168.1.1 *BRAS: Broad band Remote Access Server ISP (Internet Service Provider) 10.3.75.49 10.3.75.51 10.3.75.50 Description: If you apply for multiple IP addresses from your ISP , you ca ...

  • Siemens CL-010 - page 45

    Chapter 3:Accessing Internet 8. Set TCP/IP for your computer . Specify an IP Addr ess, subnet mask and set default gateway . eg: IP Address: 10 .3.75.51 Subnet Mask: 255.255.255.248 Gateway: 10. 3 .7 5. 49 9. Now the router is well configure d. Y ou can access into Internet. ...

  • Siemens CL-010 - page 46

    Unnumbered IP over ATM (IPoA)+NAT Description: If you apply for multiple IP addresses from your ISP , you can assign these public IP addresses to the ADSL Rout er and public serv er , e.g., W eb or FTP server . T ypically the first IP is netw ork address, the second is u sed as router IP address and the last one is subnet broa dcasting. Othe r rema ...

  • Siemens CL-010 - page 47

    Chapter 3:Accessing Internet S tart IP Address: 192.168.1.2 End IP Address: 192.168.1.254 7. Check Configure the sec ond IP Address and Subne t Mask for L AN Interface and type i n the second IP address and subnet mask. Then click Ne xt . Secondary IP Addr ess : 10.3.75.49 Subnet mask : 255.255.255.248 8. Check the network information. Make sure th ...

  • Siemens CL-010 - page 48

    Bridge Mode RDAIUS Server AAA BRAS STM-1 DSLAM Loop Bridge Mode Hub ADSL Router PPPoE Client S/W PC(S) PPP over Ethernet Default Private IP 192.168.1 .1 *BRAS: Broadband Rem o te Ac ce ss Se rv er ISP (Internet Service Provider) Description: In this example, the ADSL Router acts as a bri dge which bridging PC IP address from LAN to W AN. PC IP addr ...

  • Siemens CL-010 - page 49

    Chapter 5:Connection Mode Chapter 4: Web Configuration Some users m ight want t o set specific confi g uration for the router such as firewall, data transmission rate… and so on. This chapter will provide you advanced information of the web pages for the router for yo ur reference. Using Web-Based Manager Once your host PC is properly co nfigured ...

  • Siemens CL-010 - page 50

    Outline of Web Manager For configure the web page, please use admin as the userna me and the password. The main screen will be shown as below . Tit l e : It indicates the title of this management interface. Main Menu : Incl udes Quick S tart, S tatus, Advanced and Managem ent. Main Window : It is the current workspace of the web mana gement, contai ...

  • Siemens CL-010 - page 51

    Chapter 5:Connection Mode Quick Start The pages fo r the Quick S tart pr ovide user a qui ck way to s et for the ro uter . If you do not know more about the router, you can use the Quick S tart pages to adjust basic settings to make your router activating. Connect to Internet This is a quick way to connect to Internet by using PPPoE interface, clic ...

  • Siemens CL-010 - page 52

    After clicking on the Next butt on from the VPI/VCI web page , the following screen wi ll appear . Please choose the connection type and encapsul ation mode that you want to use and click Next for next pa ge. For example, PPP over Ethernet (PPPoE) in this screen is selected. Next, we are going to tell you different webpage fo r different protocol t ...

  • Siemens CL-010 - page 53

    Chapter 5:Connection Mode PPP over ATM/ PPP over Ethernet If the type y ou choose is PP P over A TM or PPP over Ethernet, please refer to the following information. According to the ISP’ s configuration on the server, you can choose PPPo E and PPPoA modes. If the ISP provides PPPoE service, the connection type selection will be decid ed as whethe ...

  • Siemens CL-010 - page 54

    PPP Usernam e: T ype in the user n ame that you got from your ISP . PPP P assword: T ype in the passwo rd that you got from your ISP . Always On: Check this button to make the con n ection is always active. Dial on Demand: Click this button to make a co nn ection while in demand. Enter the ti meout to cut off the network conn ectio n if there is no ...

  • Siemens CL-010 - page 55

    Chapter 5:Connection Mode PCs. S tart IP Addr ess: T ype in the start point IP address. End IP Addre ss: T ype in the end poi nt IP addr ess. Leased Time : T ype in the dur ation for the t ime. The default is 1day . DHCP Server Off: Check this item if DHCP service isn’t needed on th e LAN. Y ou can ch eck it at this time. If you find something is ...

  • Siemens CL-010 - page 56

    IP over ATM If the type you have to choose is IP over A TM, please refer to the following information. IPoA is an alternative of LAN emulation. It allows TC P/IP networ k to access A TM network and uses A T M quality o f service’ s features. Choose IPoA and click Next. None: If it is not necessary to set the W AN IP address, please click this but ...

  • Siemens CL-010 - page 57

    Chapter 5:Connection Mode In the Configure LAN side Sett i ngs web page, you have to fill in the data requested here. Primary IP Address: T ype in the firs t IP address t hat you got f rom your ISP for your LAN connection. Subnet Mask: T ype in the subn et mask that you got from your ISP for your LAN connection. Configur e the second IP Addr ess an ...

  • Siemens CL-010 - page 58

    Now , the system will reboot to activate the new settings that you have done in this section. Please wait for 2 minutes for restarting the router . ...

  • Siemens CL-010 - page 59

    Chapter 5:Connection Mode Bridging If the type you choose is Bridging , please refer to the followin g information. The bridgi ng mode can con figure your r outer to send packets received on any port such as A TM PVC or Ether net with a broa dcast MAC address to all other ports. Choose Bridging and click Next . None: If it is not necessary to set t ...

  • Siemens CL-010 - page 60

    Primary IP Address: T ype in the IP address that you got from your ISP for LAN inter face. Subnet Mask: T ype in the subn et mask that you got from your ISP for LAN interface. MTU: It means the maximum size of the packet that transmitted in the network. The packet of the data greater than th e nu mber set here will be divided into several packets f ...

  • Siemens CL-010 - page 61

    Chapter 5:Connection Mode Status Overview This page is displaying the current status for the DSL connection. It includes if the lists the LAN IP address, defaul t gateway , DNS servers IP address, firm ware version, t he period of acti vating the router , and so on. The system status will be changed according to the setting s that you configured in ...

  • Siemens CL-010 - page 62

    ADSL Line This page shows all information for ADSL. For knowing the quality of the ADSL connection, please click ADSL BER T est button to have adva nced inform ation. Click More Information to sho w more detailed information ab ou t ADSL Line Sta tu s . ADSL BER Test This test determines the quality of the ADSL connection. It is done by transferrin ...

  • Siemens CL-010 - page 63

    Chapter 5:Connection Mode When the test is over , the result will be shown on the follo wing dialog for your reference. Click Close to close this dialog. Internet Connection This page dis plays the c onnection information fo r your router , such as PVC name, category , proto col, invok ing NA T or not, IP a ddress, link stat us and so on. Traffic S ...

  • Siemens CL-010 - page 64

    This table shows the IP address rec ord for IP-to-Physical translation in your router . ...

  • Siemens CL-010 - page 65

    Chapter 5:Connection Mode Advanced Setup Local Network- IP Address This page is the sam e as you can see in the Confi gure LA N side Settings page w hile running the Quick Setup . It allows y ou to set IP Address an d Subnet Mask values for LAN interface. Primary IP Address: T ype in the firs t IP address t hat you got f rom your ISP for your LAN c ...

  • Siemens CL-010 - page 66

    DHCP Server On: Check this item if DHCP service is needed on the LAN. The router will assign IP address, gateway addr ess for each of your PCs. S tart IP Addr ess: T ype in the start point IP address. End IP Addre ss: T ype in the end poi nt IP addr ess. Leased Time : T ype in the dur ation for the t ime. The default is 1day . Relay On: Click this ...

  • Siemens CL-010 - page 67

    Chapter 5:Connection Mode The new one will be shown on the dialog right away . That is, the specified address will be reserved and not be assi g n e d by DHCP for other com puter . ...

  • Siemens CL-010 - page 68

    Local Network – UPnP The UPnP i s available only for W indows XP . If you are no t user of W indows XP , this page does not have any m eaning to you. This page allows you to enable the UPnP function throug h th e web page for your router . Internet-Connections Setting T o set W AN settings fo r each service, please open Ad v ance d– Inter net S ...

  • Siemens CL-010 - page 69

    Chapter 5:Connection Mode If you choose Non Realtime VBR, you have to type in the following data. The range for Peak Cell Rate is from 1 to 1690. The range for Sustaina ble Cell Rate is from 1 to 1689 and must be smaller than Peak Cell Rate. The range for Maxim um Burst Size is from 1 to 100. After click Next , you will see the web page listed as t ...

  • Siemens CL-010 - page 70

    Internet-DNS Server If Enable Automatic Assigned DNS checkbox is selected, this router will accept the first received DNS assignm ent from one o f the PPPoA, PP PoE or MER/DHCP enabled PVC(s) during the connection establishment. If the c h eckbox is not selected, it is necessa ry for you to e nter the primary and optional seco nd ary DNS server IP ...

  • Siemens CL-010 - page 71

    Chapter 5:Connection Mode Internet - ADSL Settings Enable ADSL Port: Check this box to enable this function . It simply invokes the lin e mode that you choose here fo r the router . Select the support of line m odes: There are several selections for your choosing. Select the one t hat you need. For Example, if y ou want to chan ge one or more physi ...

  • Siemens CL-010 - page 72

    Allow you to remove the selected static route settings. Adding a New One T o add a static route, please choose S tatic Route - Add . T ype the de stination netwo rk address, su bnet mask and gate way that you get from ISP and click Apply . Destination Network Address: The destination IP ad dres s of the network where data packets are to be s ent . ...

  • Siemens CL-010 - page 73

    Chapter 5:Connection Mode  For a router with a direct c onnection to the R outer’ s local Router , the Gateway IP Address is the address of the Router’ s local router .  For routers which must forward pac kets to another router befo re reachi ng the Router ’ s local router , the Gateway IP Address is the add ress of the intermediate rou ...

  • Siemens CL-010 - page 74

    different interface. Ot herwise, disable this function. Click Apply to invoke the settings set here. ...

  • Siemens CL-010 - page 75

    Chapter 5:Connection Mode Virtual Server-Port Forwarding The Router implements NA T to let your entire lo cal network appea r as a single machine t o the Internet. The typical situation is that you have local servers for different services and you want to make them publicly accessible. W ith NA T applied, it will translate the int ernal IP addresse ...

  • Siemens CL-010 - page 76

    IP Address seen by Intern et Users Please note that, in the above picture , both Internet users are connecting to the sam e IP address, but using dif ferent prot ocols. T o Internet users, all virtua l serv ers on your LAN have the same IP Address. This IP Address is allocated by your ISP . This address shou ld be static, rath er than dynamic, to m ...

  • Siemens CL-010 - page 77

    Chapter 5:Connection Mode From Inter net Host IP Addr ess: Select the initial place for port forwarding. If you choose SINGLE, a box will appear for you to fill in the IP address for the specific host. And, if you choose SUBNET , th e boxes of IP and Subnet will appe ar for you to fill in the IP address and subnet m ask for the specific host as the ...

  • Siemens CL-010 - page 78

    Or define by yourself by typing the words into the field of User defined. Click Apply to complete the setting. Virtual Server - DMZ Host Direct Mapping Z one (DMZ) uses a technology that m akes Router fo rwarding all i ncoming packet to internal specific serv er . T o close the function of DMZ Host, please click Discarde d. T o activate a DMZ host, ...

  • Siemens CL-010 - page 79

    Chapter 5:Connection Mode Virtual Server - Dynamic DNS The Dynamic DNS (Dynamic Domain Nas me System ) combines bot h functions of DNS and D HCP to map a dynamic IP into a fixed domain name. This page allows you to access into virtual servers with a dom ain name and pass word. Dynamic DNS ： Selects Enable to enable DDNS; select Disabled to disabl ...

  • Siemens CL-010 - page 80

    Firewall The firewall is a software that interrupts the data between the Intern et and your computer . It is the TCP/IP equivalent of a security gate at the entr ance to your company . All data must pass through it, and the firewall (functions as a security guard) will allo w on ly authorized data to be passed in to th e LAN. What the firewall can ...

  • Siemens CL-010 - page 81

    Chapter 5:Connection Mode Then, to add a new IP Filtering, click Add . This page pr ovides some set tings for you t o adjust for adding a new ou tbound IP Filtering. Allow T raffic: No stops the data transm ission, Ye s lets the data pass thr ough. Prot ocol: Here provide several default po licies for security levels for you to choose. If you don? ...

  • Siemens CL-010 - page 82

    A new IP filtering setting for Outbound traffic is created in the web page. T o edit the setting, please click th e pencil mark to get into the editing p age. T o delete the setting , click the trash mark to erase it. T o set another IP filtering, click Add again. For adding a new Inbound IP Filtering, click Inbound traffi c in the item of Select t ...

  • Siemens CL-010 - page 83

    Chapter 5:Connection Mode is the default setting. IP type of Service : The system provi des some types of service for you to choose. The meaning of each type is the same as the denotation. The default one is No change. IPQoS T o classify the upstream traf fic by assigni ng the transmission priority of the data for diffe re nt users, please use IP Q ...

  • Siemens CL-010 - page 84

    you want t o invoke the QoS traf fic rule. Destination Port: T ype in the destination port for the traf fic rule. The range is from 0 to 65535 . T raffic Priority: There are three options – L ow , Medium, and High that you can choose. It decides the order of each data transmi tted through t his device. IP Pr ecedence: The number you choose her e ...

  • Siemens CL-010 - page 85

    Chapter 5:Connection Mode Group Name: T ype in a name he re as a group name. It must be unique. The word length must not be over the length of the field. A vailable Interfaces: The available interfaces (such as Ethe rnet) will be displayed in the left side box. When you choose i t and click Add, it will be transferred into the right side box of Gro ...

  • Siemens CL-010 - page 86

    Chapter 5:Connection Mode Management Diagnostics T o check the link status for the network and your c o mputer , a diagnostic test can guide you to detect the network problem. The testing it ems are liste d and accomplis hed one by one. If the previous one is failed, than the items below that failed one will be failed too. Use this diagnostic test ...

  • Siemens CL-010 - page 87

    Chapter 5:Connection Mode Admin Account This page allows you to type in the pass word for accessing into y our DSL Router . For the Admin Account , the default setting for user passw ord is admin . I f you want to change the usernam e and the password, please retype the new password in t he Confirm fi eld for confirm ation. Then click Apply . Remot ...

  • Siemens CL-010 - page 88

    Interntet Time The router ’ s clock must synchronize with global Internet’ s time. The time you set in the screen will be adapted t o system log. Update: Click this button to refresh the curren t time. Set Time by: The default setting is Manual. If you select T ime Server , you don’t need to type in the time setting manually . The system will ...

  • Siemens CL-010 - page 89

    Chapter 5:Connection Mode There are 8 ty pes for log level and display level for your choose. The default is Debugging . The mode sele ction includes Local , Remot e and Both . The default one is Local. If you choose Remote or Both , all the events will be sent to the specified UDP port of the specified log server . Viewing Sy stem Log For viewing ...

  • Siemens CL-010 - page 90

    SNMP Setting The SNMP , the abbreviat ion of Simple Network Managem ent Protocol, is used to re fer to a collection of specification s for network management that include the protoco l itself, the d efinitio n of data structures and associated concepts. A m anagement stat ion perform s the monitoring function by retrieving the val ue of MIB objects ...

  • Siemens CL-010 - page 91

    Chapter 5:Connection Mode workstation by way of S NMP agent. Backup Config T o backup your co nfiguration for the rou ter to your com puter , you can use Backup Config web page to save the settings. And when you want to restore the settings in the future, simply open Backup Config web page and use Browse button to locate the file and click Restor e ...

  • Siemens CL-010 - page 92

    UPnP for XP Universal plu g and play (UP nP) is an archit ecture for perva sive peer to peer network connecti vity of intelligent applian ces an d PCs of all form factors. It is designed to bring easy-to-use, flexible, standards-base d connectivity t o ad-hoc or unm anaged networks whether in the h ome, in a sm all business, public spaces, or attac ...

  • Siemens CL-010 - page 93

    Chapter 5:Connection Mode 7. Now , the NA T traversal function will be provided. The ADSL router will create a new virtual se rver autom atically for mapping while the router detecting the computer ru nning som e Internet applications. ...

  • Siemens CL-010 - page 94

    Chapter 5:Troubleshooting Chapter 5: Troubleshooting If the suggeste d solutions in t his section do not resolve yo ur issue, conta ct your system administrator or Internet service prov ider . Problems with LAN PCs on the LA N cannot get IP addresses from the ADSL Router . The chances are that the interface use d as DHCP serv er is modified and the ...

  • Siemens CL-010 - page 95

    Chapter 6: Troubleshooting Request time out Then the DNS is not reachab le. Check your DNS setting on the ADSL Router . Problems with Upgrading The following lists the error messages that you may see during upgrading and the action to tak e .  Error : All t he ADSL LEDs light up a nd cannot light off as usual. Possible cause : When users execu t ...

  • Siemens CL-010 - page 96

    Chapter 6: Glossary Chapter 6: Glossary ARP ( Address Resolution Protocol ) ARP is a TCP/IP protocol for mapping an IP addr ess to a physical machine address that is recognized in the local net work, such as an Ethern et address. A host wishing to obtain a ph ysical address broadcasts an ARP request onto the TCP/IP network. The host on th e network ...

  • Siemens CL-010 - page 97

    Chapter 7: Glossary configured and mapped to a private workstatio n address when access es are made through the gateway to a publi c network. For example, the ADSL Router is assigned wi th the public IP address of 168.111.2.1. With NAT enabled, it creat es a Virt ual LAN. Each PC on th e Virtual LAN is assigned with a private IP address with defaul ...

  • Siemens CL-010 - page 98

    the cells belonging to the same connection can be distinguished. A unique and separate VPI/VCI identif ier is assign ed in advance to indicat e w hich type of cell is f ollowing, unassigned cells, physical layer OA M cells, metasignaling chann el or a generic broadcast signaling channel. Your ISP shou ld supply you with the values. ...

  • Siemens CL-010 - page 99

    Chapter 7: Glossary ...

  • Siemens CL-010 - page 100

    Appendix A: Specificatio n s Appendix A: Specifications Interface z One RJ-11 port for ADSL connection z F our RJ-45 ports for IEEE 802.3/8 02.3u 10/100 Base- T auto-sensing and auto-crosso ver Ethernet connection z One hidden reset button for re storing to factory default settings Reg u l a t or y Approvals and Compliance EMI: FCC part 15 Cl ass B ...

  • Siemens CL-010 - page 101

    Appendix A: Specificatio n s ...

  • Siemens CL-010 - page 102

    Appendix B: Server Setup for 802 .1x Client Appendix B: Server Setup for 802.1x Client Getting Client Certificate 1. Please connect the client to a network that doesn’t req uire port authentictaion. 2. Open up Microsof t Explorer in Windows XP, and go to http://<yourserv er>/certsrv. 3. Authenticate to the server using your account that you ...

  • Siemens CL-010 - page 103

    Appendix C: WEEE – B2C 5. Make sure that User certificate request : User Certificate is selected, and click Next . 6. Click Submit in this dialog. 7. Now, you'll see status messages on the screen, then your certificate will be returned to you. Click Install this certificate. 8. You'll receive a confirm ation message about accepting the ...

  • Siemens CL-010 - page 104

    Appendix C: WEEE – B2C All electrical and electronic products shoul d be di sposed of separately from the municipal waste stream via designated coll ection facilities appointed by the government or the local a uthorit ies. The correct disposal and separate collection of your old appliance will help prevent potential negative consequences for the ...

Manufacturer Siemens Category Network Router

Documents that we receive from a manufacturer of a Siemens CL-010 can be divided into several groups. They are, among others:
- Siemens technical drawings
- CL-010 manuals
- Siemens product data sheets
- information booklets
- or energy labels Siemens CL-010
All of them are important, but the most important information from the point of view of use of the device are in the user manual Siemens CL-010.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Siemens CL-010, service manual, brief instructions and user manuals Siemens CL-010. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Siemens CL-010.

Similar manuals

A complete manual for the device Siemens CL-010, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Siemens CL-010 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Siemens CL-010.

A complete Siemens manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Siemens CL-010 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Siemens CL-010, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Siemens CL-010, that we can find in the current document
3. Tips how to use the basic functions of the device Siemens CL-010 - which should help us in our first steps of using Siemens CL-010
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Siemens CL-010
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Siemens CL-010 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Siemens CL-010?

Use the form below

If you did not solve your problem by using a manual Siemens CL-010, ask a question using the form below. If a user had a similar problem with Siemens CL-010 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)