English dropdown-ico

Manual Varimixer MK IV

32 pages 1.43 mb
Download

Go to site of 32

Summary
  • Varimixer MK IV - page 1

    THE PROGRAMMABLE CONTROL SYSTEM MK-IV User’s Manual ...

  • Varimixer MK IV - page 2

    ...

  • Varimixer MK IV - page 3

    General descriptions MODES The system contains six different modes: 1. MANUAL MODE: The mode when the mixer is operated like a man - ual controlled mixer. Instead of executing a programmed recipe, the mixer is started and operated until it is manually shut off. 2. PROGRAMMING MODE: The mode where all programming and editing takes place. 3. PROGRAM ...

  • Varimixer MK IV - page 4

    The Keypad The Keypad is used for entering data to the system. ITEM FUNCTION EXPLANATION 1. Program No. Displays the program Number being executed. 2. Step Displays the step number being executed. 3. Speed Displays the set-speed. 4. Time Displays the elapsed time since start or displays the remaining time to shut down. 5. Text Area OVERLOAD: MIxer ...

  • Varimixer MK IV - page 5

    6. Enter Used for stepping through a program. 7. CLR 8. Speed up/down arrows. 9. Time up/down arrows. 10. Program 11. Pause 12. Numeric keys 13. Emergency Stop Clears a flashing display. Used for adjusting the the speed while the mixer is running. Used for adjusting the the time. Used to enter/exit program-programming mode. Pauses the mixer without ...

  • Varimixer MK IV - page 6

    How to run the mixer manually. SPEED Mode. Enter the speed desired. Push Enter the time desired. Push Push How to input a program. A flashing display indicates that it is expecting the operator to key in a value. A step is always a combination of speed and time. An example is 100 R.P.M. for 5:00 minutes or 0 R.P.M. for 15 seconds (which is a 15 sec ...

  • Varimixer MK IV - page 7

    To program a recipe. Push Push Enter the speed desired. “HOLD FOR 3 SECONDS” Repeat this process for as many as 9 steps per program, after the 9th step , the next program num - ber will display, ready to enter a new recipe.This will continue up to 25 programs. Push Push Enter the time desired. Example To edit a recipe or to correct mistakes, us ...

  • Varimixer MK IV - page 8

    To run a programmed recipe. Push Push Enter the Program number. Push After the ENTER key has been pushed, the data in step 1 will be displayed along with the program number. After the last program step has been executed, the mixer will slow to minimum speed and shut off. The mixer can be stopped at any time during a recipe by using the “PAUSE” ...

  • Varimixer MK IV - page 9

    To enter “FIXED MODE” Push Push “99” “HOLD FOR 3 SECONDS” Push Push “1 2 3 4” Push Push the program number. Push To exit “FIXED MODE” Push “HOLD FOR 3 SECONDS” Push “1 2 3 4” Push 7 ...

  • Varimixer MK IV - page 10

    Control Data for Program 26 Program 26 contains the control data required by the computer to operate. This data differs from model to model. To access Program 26. Push “HOLD FOR 3 SECONDS” Push Push “26” Push “1 2 3 4” Push Push until you reach Step 7. Enter the value on the following chart that matches the mixer model. Repeat for step ...

  • Varimixer MK IV - page 11

    A D In the electronics fail. It is possible to bypass the control system if the electronics fail. Please note, when the system is bypassed, the safety devices do not operate. Extreme care should be taken when operating the mixer. 1. Switch off the main power. 2. Open the top lid, flip the dip switch (B) on the back of the computer control from “A ...

  • Varimixer MK IV - page 12

    E:401 E:301 E:201 Error Codes A error in the mixer will trigger an ERROR code in the time display. See the chart below for an explanation of error codes and the procedure for correcting them. E:201 The servo motor block actuator (B) did not contact the minimum speed microswitch (A) after the stop button was pushed or the programmed recipe completed ...

  • Varimixer MK IV - page 13

    E:301 There is no signal from the speed pickup (hall effect sensor). To correct this error: 1) Check that the sensor (D) is centered directly above the track of the 3 magnets (F) on the pulley and the gap between the sensor and magnets is 1/16”. If not , bend and / or move the bracket (I) holding the sensor. 2) Inspect the three wires between the ...

  • Varimixer MK IV - page 14

    E:4:01 The values in program 26 steps 7, 8 and 9 are missing or incorrect. To correct this error: Push “HOLD FOR 3 SECONDS” Push Push “26” Push “1 2 3 4” Push Push until you reach Step 7. Enter the value on the following chart that matches the mixer model. Repeat for step 8 and 9. Step 7 Mixer Model W30 W40 W60 W80 W100 W150 Cinnabon 40 ...

  • Varimixer MK IV - page 15

    MAINTENANCE AND ADJUSTMENTS Computer Control 2 Fuses: 8 Amp 6.3 x 32 MM P.N. 20E-418.1 Power Supply 1 Fuse:1.5 Amp 6.3 x 32 MM P.N. 20E-418 Fuse data and component location Hall Effect Sensor P.N. 30E-500M Bowl Lift Servo Motor (If equipped) P.N. 100N-86.02 Speed Servo Motor P.N. 60E-517.02 Bowl Lift Microswitches (PN 61-522) Each 13 ...

  • Varimixer MK IV - page 16

    Models W30, W40, W40P, W60,W60P Bowl adjustments W30 = 6 3/8” W40 = 6 3/8” W60 = 7” 14 ...

  • Varimixer MK IV - page 17

    Bowl adjustments Models W80, W100, W150N W80 = 9 1/8” W100 = 11 5/8” W150 = 11 7/8” 15 ...

  • Varimixer MK IV - page 18

    Lubrication White Lithium Grease (IE Lubriplate ) Nye Fluorocarbon Gel 868VH Order from authorized service agent Part number: WHITE GREASE 16 ...

  • Varimixer MK IV - page 19

    Belt adjustments 17 NEVER move the base for motor ( R )(in the oblong holes) , this is a factory setting and is NOT used to tighten the belts.If the entire unit is to be exchanged, reference the below table. Models W30-W40(P) Distance (B) 11 1/2 inches Models W60-W150 Distance (B) 12 1/4 inches 1. Start by tightening the V-belts (C) . 1. A) Loosen ...

  • Varimixer MK IV - page 20

    Belt Exchange 18 1. Loosen Bolt (J) and remove washers (H). 2 2. Remove cotterpin (T) and dowel pin (E) from servo linkage. 2 . 3. Remove vari drive belt (A) from pulleys. 2 4. Remove Hall Effect sensor (X) from the rear of the computer. 3 5. Loosen bolts (D) and remove the front v-belts (C) by tilting the center pul .... ley assembly (L) forward a ...

  • Varimixer MK IV - page 21

    Belt Exchange 19 ...

  • Varimixer MK IV - page 22

    Adjustment of low and high speed microswitches. 20 ...

  • Varimixer MK IV - page 23

    Adjustment of low and high speed microswitches. 21 ...

  • Varimixer MK IV - page 24

    Speed Servo System Figure Number Description W30, W40 , W40P W80, W100 , W150 1..........................Sensor..........................30E-500M.........................30E-500M 2..........................Bolt M6.................. ......STA 5432.........................STA 5432 3..........................Magnets.......................30E-515M..... ...

  • Varimixer MK IV - page 25

    Speed Servo System 23 ...

  • Varimixer MK IV - page 26

    Power Supply Figure Number Description All Models 1..........................Transformer..............................................................60E-430 2..........................Filter....................................................................... . ..20E-419 3..........................Relay 24VDC..................................... ...

  • Varimixer MK IV - page 27

    Power Supply 1 2 3 4 5 6 7 8 9 11 10 25 ...

  • Varimixer MK IV - page 28

    26 ...

  • Varimixer MK IV - page 29

    27 ...

  • Varimixer MK IV - page 30

    Power Supply Wiring Diagram 1.5 Amp 28 ...

  • Varimixer MK IV - page 31

    ...

  • Varimixer MK IV - page 32

    5489 Campus Drive Shreveport LA 71129 (800) 222-1138 (318) 635-3131 Fax ...

Manufacturer Varimixer Category Mixer

Documents that we receive from a manufacturer of a Varimixer MK IV can be divided into several groups. They are, among others:
- Varimixer technical drawings
- MK IV manuals
- Varimixer product data sheets
- information booklets
- or energy labels Varimixer MK IV
All of them are important, but the most important information from the point of view of use of the device are in the user manual Varimixer MK IV.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Varimixer MK IV, service manual, brief instructions and user manuals Varimixer MK IV. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Varimixer MK IV.

Similar manuals

A complete manual for the device Varimixer MK IV, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Varimixer MK IV by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Varimixer MK IV.

A complete Varimixer manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Varimixer MK IV - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Varimixer MK IV, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Varimixer MK IV, that we can find in the current document
3. Tips how to use the basic functions of the device Varimixer MK IV - which should help us in our first steps of using Varimixer MK IV
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Varimixer MK IV
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Varimixer MK IV in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Varimixer MK IV?

Use the form below

If you did not solve your problem by using a manual Varimixer MK IV, ask a question using the form below. If a user had a similar problem with Varimixer MK IV it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)