English dropdown-ico

Manual Sigma AS-H50Y

20 pages 0.71 mb
Download

Go to site of 20

Summary
  • Sigma AS-H50Y - page 1

    AS-H40Y - 12kW AS-H50Y - 15kW AS-H60Y - 18kW AL TO Hea t Pump inst alla tion manu al F1-F7 ...

  • Sigma AS-H50Y - page 2

    1 CUSTOMER NAME........................................................................ POOL DEALER.............................................................................. DA TE INST ALLED.......................................................................... SERIAL NO........................................................................ ...

  • Sigma AS-H50Y - page 3

    HEA T PUMP- AS-H40Y 12kW 2 ...

  • Sigma AS-H50Y - page 4

    3 HEA T PUMP- AS-H50Y (15kW) & AS-H60 (18kW) ...

  • Sigma AS-H50Y - page 5

    INST ALLA TION AND SITING Prior to installing your heat pump:- All heat pumps are factory assembled and tested prior to delivery . Please check for any external damage especially to the evaporator fins, please diagram below . Do not be concerned about minor damage or indent ations to the fins (especially where the fan unit is mounted) as it will no ...

  • Sigma AS-H50Y - page 6

    5 PLUMBING Alto heat pumps are supplied with 1.5" BSP parallel threads, male. We strongly recommend a 1.5" female socket union is applied to inlet/outlets for future draining and servicing of the appliance. Alto heat pumps must be inst alled in the return line after the filter . If an existing heater or back-up heater has been installed t ...

  • Sigma AS-H50Y - page 7

    N L ON OFF CONT A CTOR 12 HEA TER Red Black OUTLET FLOW SWITCH OPERA TION WA TER FLOW FROM PUMP SOCKET UNION TEE INLET OFF ON Alternat ive w irin g route SOCKET UNION RETURN W A TE R FLOW TO POOL 1. Insert reducing bushes (provided) into 1.5” T ee using suitable adhesive. 2. Connect 1.5” T ee to socket union adjacent to Inlet on heat pump. T ee ...

  • Sigma AS-H50Y - page 8

    7 Ball Va l v e BACK WASH FILTER FIL TER Pool Position for option al Erosion Fe eder Non-Retur n V alve Back-Up Heater if required Condensat e W ater to waste PUMP Female/ Threade d Socket Union Drw .1 Recommended plumbing layout for a st andard heat pump installation. Drw .2 Recommended plumbing layout when incorporating Solar Heating. If an incre ...

  • Sigma AS-H50Y - page 9

    Ball Va l v e BACKW ASH FIL TER FIL TER Pool Non-R etu rn Valve Back-Up Heater if required Condensate W ater to waste PUMP Female/ Threaded Socket Union to be applied on all inlet/outlets Position for optional Erosion Feeder Ball Va l v e Ball Va l v e Condensate W ater to waste required or Erro sion Feede r if instal led Drw .4 Recommended plumbin ...

  • Sigma AS-H50Y - page 10

    9 ELECTRICAL CONNECTION & CIRCUIT DIAGRAM IMPORT ANT . It is recommended that all electrical supplies and connections are carried out by a qualified electrician , in accordance with I.E.E. standards, latest issue, or local codes of practice as applicable. Also recommended is a protected supply to incorporate fuses or motor type circuit breaker ...

  • Sigma AS-H50Y - page 11

    1. When electric supply is connected the ‘Run’ power light will be on and the display panel will display the current water temperature. ie.10 H = 10°C. 2. On/OFF button to turn heater on and off. 3. The ‘set’ button is used to set the F1-6 functions ie.water temperature, defrosting cycle and defrosting time etc. see pages 1 1-12 PLEASE REA ...

  • Sigma AS-H50Y - page 12

    11 When the ON/OFF buttons is pressed for the first time, the display panel will display the current water temperature and the desired pool temperature. eg. the display may read 10 40 ----- 10 is the current water temperature 10°C and 40 is the desired water temperature 40°C. ADJUSTING THE POOL W A TER TEMPERA TURE Using the up and down buttons, ...

  • Sigma AS-H50Y - page 13

    When the SET button is pressed for the fourth time, the display p anel will display:- F4 : Operation Mode. F4 C : Cooling Mode. F4 H : Heating Mode When the SET button is pressed for the fif th time, the display panel will display:- F5 : The defrosting temperature of the evaporator pipe . The recommended temperature setting for the UK should be set ...

  • Sigma AS-H50Y - page 14

    13 RED area RED area area RED area RED area area RED area RED area area After the water heater has been running for more than 24 hrs, it should be running at full capacity . The PSI reading should be in the region 150 -200. If you want to make the heat pump run more efficiently the water flow should be adjusted by checking the pressure meter displa ...

  • Sigma AS-H50Y - page 15

    E1 : the water temperature sensor is not working correctly . E2 : the tube sensor is not working correctly . Please contact your dealer . E3 : Pool filtration is running but water flow is not sensed. ‘Flow Switch’ may not be working properly or there is a lack of water flow . Backwash filter and check suction lines (Skimmer(s) & Main Drain( ...

  • Sigma AS-H50Y - page 16

    15 AUT O REST ART AND DEFROSTING FUNCTION AUTO REST ART FUNCTION The Alto water heat pump has an auto rest art function. When the power supply is switched off accidentally , it will automatically save the operation mode. When the power supply is restored, the unit will automatically restart af ter five minutes and operate in the same working mode. ...

  • Sigma AS-H50Y - page 17

    WINTERISING / ST ART -UP procedure - ALL MODELS W A TER CHEMISTR Y The following water quality must be maintained at all times to prevent premature corrosion. It is recommended that your water balance is checked and balanced by a pool professional. Y our warranty does not cover for damaged caused by poor water chemistry and neglect. pH: 7.2 -7.6 T ...

  • Sigma AS-H50Y - page 18

    17 AL T O W ARRANTY POLICY This voluntary policy is supplement al to and in no way affects any st atutory rights which the customer may have. 1 W arranties 1.1 Paramount Pools warrants the Alto Heat Pump for a period of one (1) year from the date installed for both part s and labour . 1.2 At the end of the first year the following warranties apply ...

  • Sigma AS-H50Y - page 19

    HEA T PUMP SER VICE An Alto heat pump should give you many years trouble free service. However , to obtain the maximum efficiency from your heater Alto recommend that your heater is checked and serviced every 12 months. Service & extended warranty packages are available from a UK Service Agent (see contact det ail below). HEA T PUMP BREAKDOWN I ...

  • Sigma AS-H50Y - page 20

    Model No. AS-H40Y AS-H50Y AS-H60Y 12kW 15kW 18kW Heating Capacity (Btu) 40000 50000 60000 Cooling Capacity (Btu) 35000 42000 55000 Rated Input (W) Heating 2540 3185 3790 Cooling 2465 3020 3900 PTC Power (W) -------- -------- -------- COP for Heating (w/w) 4.42 4.40 4.44 (at 20 °C ambient air temperature) Refrigerant R407C R407C R407C Power Supply ...

Manufacturer Sigma Category Heat Pump

Documents that we receive from a manufacturer of a Sigma AS-H50Y can be divided into several groups. They are, among others:
- Sigma technical drawings
- AS-H50Y manuals
- Sigma product data sheets
- information booklets
- or energy labels Sigma AS-H50Y
All of them are important, but the most important information from the point of view of use of the device are in the user manual Sigma AS-H50Y.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Sigma AS-H50Y, service manual, brief instructions and user manuals Sigma AS-H50Y. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Sigma AS-H50Y.

Similar manuals

A complete manual for the device Sigma AS-H50Y, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Sigma AS-H50Y by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Sigma AS-H50Y.

A complete Sigma manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Sigma AS-H50Y - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Sigma AS-H50Y, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Sigma AS-H50Y, that we can find in the current document
3. Tips how to use the basic functions of the device Sigma AS-H50Y - which should help us in our first steps of using Sigma AS-H50Y
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Sigma AS-H50Y
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Sigma AS-H50Y in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Sigma AS-H50Y?

Use the form below

If you did not solve your problem by using a manual Sigma AS-H50Y, ask a question using the form below. If a user had a similar problem with Sigma AS-H50Y it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)