English dropdown-ico

Manual Vulcan-Hart ML-136221-00G24

24 pages 1.73 mb
Download

Go to site of 24

Summary
  • Vulcan-Hart ML-136221-00G24 - page 1

    SERVICE MANUAL Heavy Duty Gas Griddles MODEL MLS 924RE ML-135221-00G24 936RE ML-135222-00G36 948RE ML-135223-00G48 960RE ML-135224-00G60 972RE ML-135225-00G72 www.vulcanhart.com 924RE AGE24 MODELS MLS AGE24 ML-135226-00G24 AGE36 ML-135227-00G36 AGE48 ML-135228-00G48 AGE60 ML-135229-00G60 AGE72 ML-135230-00G72 www.wolfrange.com ITW Food Equipment Gr ...

  • Vulcan-Hart ML-136221-00G24 - page 2

    - 2 - TABLE OF CONENTS INSTALLATION ........................................................................................................................... 4 COMPONENT LOCATION ....................................................................................................................... 5 948RE AND AGE48 CONTROL PANEL ................. ...

  • Vulcan-Hart ML-136221-00G24 - page 3

    - 3 - SYMPTOM – ONE BURNER HAS A DELAYED I GNITION; A SEVERAL SECOND LAPSE BETWEEN THE INDICATOR LIGH T TURING ON AND W HEN THE BURNER ACTUALLY LIGHTS. ............................................................................................................................... ... 16 BURNER REMOVAL .............................................. ...

  • Vulcan-Hart ML-136221-00G24 - page 4

    GENERAL INTRODUCTION This manual is prepared for the use of trained service technicians and should only be used by those who are properly qualified. This manual is not intended to be all encompassing. You should read, in it's entirety, the repair procedure you wish to perform to determine if you have the necessary tools, instruments and skills ...

  • Vulcan-Hart ML-136221-00G24 - page 5

    COMPONENT LOCATION 948RE AND AGE48 CONTROL PANEL - 5 - ...

  • Vulcan-Hart ML-136221-00G24 - page 6

    CONTROL PANEL Disconnect the electrical power and follow lockout / tagout procedures The Control Panel holds the thermostats, indicator lights and power switch, and is connected to the Control Plate with a Panel Connector 1. Remove the four screws securing the control panel. There are two screws at each end of the panel. 2. Pull the control panel f ...

  • Vulcan-Hart ML-136221-00G24 - page 7

    HEAT SHIELD Disconnect the electrical powe r and f ollow lockout / tagout procedures The heat shield protects the electrical components and should only be temporarily removed for easier replacement of some the control components. 1. Remove the control panel. 2. Remove screws along the top edge that secure the heat shield. 3. The shield clamps on th ...

  • Vulcan-Hart ML-136221-00G24 - page 8

    Disconnect the electrical power and follow lockout / tagout procedures THERMOSTAT TROUBLESHOOTING SYMPTOM – NO POWER TO THE BURNER S OLENOID 1. Check for loose or excessively greasy/dirty connections at terminals 2. Check for continuity/resistance between the tw o thermostat terminals with wires disconnected A. If you get continuity/resistance wi ...

  • Vulcan-Hart ML-136221-00G24 - page 9

    THERMOSTAT CALIBRATION 1. Each thermostat cont rols a 12” zone of the griddle. Usin g a Surface Pr obe temper ature measurement de vice, observe the temperatures at the center points of the cooking zon es. These points are lo cated by starting 6” fr om the side splash (left or right) and every 12” across the width of the griddle, with a ll po ...

  • Vulcan-Hart ML-136221-00G24 - page 10

    TEMPERATURE DIAL INDICATOR LIGHT KNOB POWER SWITCH KNOB GUARD ( OPTIONAL ) POWER ON/OFF SWITCH The Power Switch controls the power supply to all other electronic com ponents. Disconnect the electrical power and follow lockout / tagout procedures POWER SWITCH TROUBL ESHOOTING SYMPTOM – NO POWER BEING SUPPLIE D TO THE UNIT 1. Check for loose or exc ...

  • Vulcan-Hart ML-136221-00G24 - page 11

    A. If no voltage – check wiring for short or break and check thermostat B. If you have 120V – replace indicator light. Disconnect the electrical power and follow lockout / tagout procedures INDICATOR LIGHT REMOVAL 1. Remove the control panel 2. Label and disconnect wires to the light 3. Squeeze the light retainers and slide the light out throug ...

  • Vulcan-Hart ML-136221-00G24 - page 12

    Disconnect the electrical power and follow lockout / tagout procedures FLAME SWITCH TROUBLESHOOTING SYMPTOM – INDICATOR LIGHTS, THERMOST ATS AND BURNER V ALVES NOT WORKING 1. Check for loose or excessively greasy/dirty terminal connections 2. Check that flame switch probe is fully engulf ed in the pilot flame and glowing cherry red. A. If sensor ...

  • Vulcan-Hart ML-136221-00G24 - page 13

    Disconnect the electrical power and follow lockout / tagout procedures SPARK IGNITOR TROUBLESHOOTING SYMPTOM – NO SPARK BETWEEN PILOT HEAD AND EL ECTRODE 1. Check for loose or greasy/dirty connections at all terminals (including electrode wire) 2. Check for 120 voltage from L1 terminal to ground a. If no voltage check on/off switch and wiring for ...

  • Vulcan-Hart ML-136221-00G24 - page 14

    Disconnect the electrical power and follow lockout / tagout procedures SOLENOID VALVE TROUBLESHOOTI NG SYMPTOM – NO GAS FLOW TO BURNER 1. Check terminals for loose or greasy/dirty connections 2. Check gas pressure – check for orif ice obstructions. 3. With thermostat, indicator light and power switch on – check for 120 voltage between the two ...

  • Vulcan-Hart ML-136221-00G24 - page 15

    PILOT ASSEMBLY REMOVAL Disconnect the electrical power and follow lockout / tagout procedures Shut off gas supply - 15 - 1. Remove control panel and heat shield 2. Reaching underneath the front of the unit, remove the pilot tube fitting and disengage the pilot tube from the pilot. 3. Pull the flame switch probe straight down and out from the snap i ...

  • Vulcan-Hart ML-136221-00G24 - page 16

    Disconnect the electrical power and follow lockout / tagout procedures BURNER TROUBLESHOOTING SYMPTOM – ALL BURNERS HAVE A LOWE R OR HIGHER FLAME THAN NORMAL. 1. Check gas pressure SYMPTOM – ONE OR MORE BURNERS HAVE LOWER FLAME LEVE L THAN THE OTHERS. 1. Check gas pressure 2. Check burner orifice for obstructions 3. Adjust burner air shutter 4. ...

  • Vulcan-Hart ML-136221-00G24 - page 17

    BURNER CLIP (U NDERNEATH ) FLASH TUBE PILOT ASSY IGN ITION PORTS AIR SHUTTER ORIFICE MAIN BURNERS These photos are for reference – it should not be necessary to remove the griddle top to perform the procedures listed in this manual. GAS REGULATOR REGULATOR INSTALLED IN A HORIZONTAL, UPRIGHT POSITION The 900RE and AGE series units must have an ext ...

  • Vulcan-Hart ML-136221-00G24 - page 18

    REGULATOR TROUBLESH OOTING SYMPTOM – UNIT WILL NOT MAINTAIN CONSISTENT PRESSURE 1. Check that vent limiter is not clogged by grease and debris 2. Check store gas pressure before regulator with all equipment on that line turned on and consuming gas A. For natural gas should be between 7” and 14” W.C. B. For propane gas should be between 12” ...

  • Vulcan-Hart ML-136221-00G24 - page 19

    SEQUENCE OF OPERATION Operation is the same for all size griddles. The neutral wire from the power source is directly connected to a terminal on each thermostat, the N terminal on each ignition module and one terminal on the pilot solenoid. 1. The power on/off switch is set to the ON position. 2. Voltage is applied to the following terminals A. Ter ...

  • Vulcan-Hart ML-136221-00G24 - page 20

    WIRING DIAGRAMS WIRING DIAGRAM – 24-INCH GRIDDLE - 20 - ...

  • Vulcan-Hart ML-136221-00G24 - page 21

    WIRING DIAGRAM – 36-INCH GRIDDLE - 21 - ...

  • Vulcan-Hart ML-136221-00G24 - page 22

    WIRING DIAGRAM – 48-INCH GRIDDLE - 22 - ...

  • Vulcan-Hart ML-136221-00G24 - page 23

    WIRING DIAGRAM – 60-INCH GRIDDLE - 23 - ...

  • Vulcan-Hart ML-136221-00G24 - page 24

    WIRING DIAGRAM – 72-INCH GRIDDLE - 24 - ...

Manufacturer Vulcan-Hart Category Griddle

Documents that we receive from a manufacturer of a Vulcan-Hart ML-136221-00G24 can be divided into several groups. They are, among others:
- Vulcan-Hart technical drawings
- ML-136221-00G24 manuals
- Vulcan-Hart product data sheets
- information booklets
- or energy labels Vulcan-Hart ML-136221-00G24
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vulcan-Hart ML-136221-00G24.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vulcan-Hart ML-136221-00G24, service manual, brief instructions and user manuals Vulcan-Hart ML-136221-00G24. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vulcan-Hart ML-136221-00G24.

Similar manuals

A complete manual for the device Vulcan-Hart ML-136221-00G24, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vulcan-Hart ML-136221-00G24 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vulcan-Hart ML-136221-00G24.

A complete Vulcan-Hart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vulcan-Hart ML-136221-00G24 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vulcan-Hart ML-136221-00G24, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vulcan-Hart ML-136221-00G24, that we can find in the current document
3. Tips how to use the basic functions of the device Vulcan-Hart ML-136221-00G24 - which should help us in our first steps of using Vulcan-Hart ML-136221-00G24
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vulcan-Hart ML-136221-00G24
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vulcan-Hart ML-136221-00G24 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vulcan-Hart ML-136221-00G24?

Use the form below

If you did not solve your problem by using a manual Vulcan-Hart ML-136221-00G24, ask a question using the form below. If a user had a similar problem with Vulcan-Hart ML-136221-00G24 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)