English dropdown-ico

Manual Scag Power Equipment STT-31BSG

64 pages 2.56 mb
Download

Go to site of 64

Summary
  • Scag Power Equipment STT-31BSG - page 1

    MODEL STT-31BSG OPERATOR’S MANUAL THIS MANUAL CONT AINS THE OPERA TING INSTRUCTIONS AND SAFETY INFORMA- TION FOR YOUR SCAG MOWER. READING THIS MANUAL CAN PROVIDE YOU WITH ASSIST ANCE IN MAINTENANCE AND AD- JUSTMENT PROCEDURES TO KEEP YOUR MOWER PERFORMING T O MAXIMUM EFFI- CIENCY . THE SPECIFIC MODELS THA T THIS BOOK COVERS ARE CONT AINED ON THE ...

  • Scag Power Equipment STT-31BSG - page 2

    F AILURE TO FOLLOW SAFE OPERA TING PRACTICES MA Y RESUL T IN SERIOUS INJUR Y . * Keep all shields in place, especially the grass discharge chute. * Before performing any maintenance or service, stop the machine and remove the spark plug wires and ignition key . * If a mechanism becomes clogged, stop the engine before cleaning. * Keep hands, feet an ...

  • Scag Power Equipment STT-31BSG - page 3

    I T ABLE OF CONTENTS SUBJECT PA G E Section 1 - General Information 1.1 Introduction ............................................................................................................................. 1 1. 2 Directional Reference ....................................................................................................... ...... ...

  • Scag Power Equipment STT-31BSG - page 4

    II T ABLE OF CONTENTS (CONT'D) SUBJECT PA G E Section 6 - Adjustments 6. 1 Parking Brake Adjustment .................................................................................................... 20 6. 2 T ravel Adjustments .......................................................................................................... ..... 2 0 ...

  • Scag Power Equipment STT-31BSG - page 5

    1 GENERAL INFORMA TION 1.1 INTRODUCTION Y our mower was built to the highest standards in the industry . However , the prolonged life and maximum efficiency of your mower depends on you following the operating, maintenance and adjustment instructions in this manual. If additional information or service is needed, contact your Scag Power Equipment D ...

  • Scag Power Equipment STT-31BSG - page 6

    2 CE Mark T ransmission Choke On/Start Spring T ension on Idler Oil Off/Stop SYMBOL DESCRIPTION SYMBOL DESCRIPTION ISO Symbols Spinning Blade 48071S Parking Brake WARNING FALLING HAZARD USE ONLY SCAG APPROVED RIDING ATTACHMENTS SEE OPERATOR'S MANUAL 481109 Falling Hazard ...

  • Scag Power Equipment STT-31BSG - page 7

    3 Slow Fast Cutting Element - Engage Cutting Element - Basic symbol Cutting Element - Disengage Continuously V ariable - Linear Read Operator's Manual Keep Bystanders A way Pinch Point 481039S SYMBOL DESCRIPTION SYMBOL DESCRIPTION Hourmeter/Elapsed Operating Hours Thown Object Hazard ...

  • Scag Power Equipment STT-31BSG - page 8

    4 SAFETY INFORMA TION This symbol means “Attention! Become Alert! Y our Safety is Involved!" The symbol is used with the following signal words to attract your attention to safety messages found on the decals on the machine and throughout this manual. The message that follows the symbol contains important information about safety . T o avoid ...

  • Scag Power Equipment STT-31BSG - page 9

    5 10. DO NOT add fuel to a running or hot engine. Allow the engine to cool for several minutes before adding fuel. 1 1 . Keep flammable objects (cigarettes, matches, etc.), open flames and sparks away from the fuel tank and fuel container . 12 . Equipment must comply with the latest requirements per SAE J137 and/or ANSI/ASAE S279 when driven on pub ...

  • Scag Power Equipment STT-31BSG - page 10

    6 Section 2 2.4 OPERA TION CONSIDERA TIONS (CONT'D) 3. T o prevent tipping or loss of control, start and stop smoothly , avoid unnecessary turns and travel at reduced speed. 4. When using any attachment, never direct the discharge of material toward bystanders or allow anyone near the machine while in operation. 5. Before attempting to start t ...

  • Scag Power Equipment STT-31BSG - page 11

    7 Section 2 2.6 SAFETY AND INSTRUCTIONAL DECALS WARNING INSTALL BELT COVER BEFORE OPERATING MACHINE READ OPERATOR'S MANUAL 481039 390S0150C 481568 FORWARD REVERSE F R 482580 482710 482290 482286 482285 481039 ...

  • Scag Power Equipment STT-31BSG - page 12

    8 SPECIFICA TIONS Section 3 SCA G “SABRE T OO TH TIGER” ZER O-TURN RIDER MODEL: STT– 31BSG ENGINE General Type: Heavy duty industrial/commercial Brand: Briggs Daihatsu Vanguard Liquid Cooled 31 HP Model: DM950G Horsepower: 31 HP @ 3600 RPM Type: water cooled 4 cycle, overhead valve, 3 cylinder, gas engine Displacement: 952 cc Cylinders: 3 inl ...

  • Scag Power Equipment STT-31BSG - page 13

    9 Section 3 SPECIFICA TIONS (CON'T) SCA G “SABRE T OO TH TIGER” ZER O-TURN RIDER MODEL: STT– 31BSG CUTTER DECK Type: SMST-72A ("Advantage") & SMST-61A ("Advantage") - Floating, adjustable anti- scalping, hybrid design combines out-front and belly-mount designs. "Advantage" - special extended front edge a ...

  • Scag Power Equipment STT-31BSG - page 14

    10 Section 4 OPERA TING INSTRUCTIONS Do not attempt to operate this mower unless you have read this man ual. Learn the location and purpose of all controls and instruments bef ore you operate this mower . 4.1 CONTROLS AND INSTR UMENT IDENTIFICA TION Before operating the mower , familiarize yourself with all mower and engine controls. Knowing the lo ...

  • Scag Power Equipment STT-31BSG - page 15

    11 Section 4 5 . V oltmeter (Figur e 4-1). Indicates the condition of the charging system. When the engine is running, in normal operating conditions, the needle should be in the 12 to 14 volt range. 6 . Oil Pressure (Figure 4-1). Indicates engine oil pressure. Reference the engine operator's manual for further information. 7 . Hourmeter (Figu ...

  • Scag Power Equipment STT-31BSG - page 16

    12 Section 4 4.3 INITIAL RUN-IN PROCEDURES (First Day of Use or Approximately 10 Hours) 1. Check all belts for proper alignment and wear at 2, 4 and 8 hours. 2. Change the engine oil and oil filter after the first 5 hours of operation. (See Section 7.4.) 3. Check hydraulic oil level in reservoir . (See Section 7.3.) 4. Check for loose hardware. T i ...

  • Scag Power Equipment STT-31BSG - page 17

    13 Section 4 T o steer the mower left while traveling forward, pull the left steering lever back. The further the lever is pulled back, the quicker the mower will turn left. T o steer the mower right while traveling forward, pull the right steering control lever back. The further the lever is pulled back, the quicker the mower will turn right. -NOT ...

  • Scag Power Equipment STT-31BSG - page 18

    14 Section 4 4. Always operate the engine at full throttle to properly maintain cutting speed. If the engine starts to lug down, reduce the forward speed and allow the engine to operate at maximum RPM. 4.7 HILLSIDE OPERA TION DO NO T operate on steep slopes. T o chec k a slope, attempt to back up it (with the cutter dec k down). If the machine can ...

  • Scag Power Equipment STT-31BSG - page 19

    15 Section 4 4.10 REMO VING CLOGGED MA TERIAL 1. If the discharge chute becomes clogged, shut off the engine and remove the ignition key . Using a stick or similar item, dislodge the clogged material. Then resume normal mowing. 4.11 MO VING MO WER WITH ENGINE ST OPPED T o “free-wheel” or move the mower around without the engine running, place t ...

  • Scag Power Equipment STT-31BSG - page 20

    16 Section 4 4.13 ADJUSTING CUTTING HEIGHT The mower deck can be adjusted from a height of 1-inch to 6 inches at 1/4-inch intervals. T o adjust the cutting height: 1. Disengage the power to the cutter blades. 2. Push the cutting height adjustment foot pedal all the way forward using your right foot until it locks in place. (Figure 4-6). 3. Insert t ...

  • Scag Power Equipment STT-31BSG - page 21

    Section 5 17 Stringers - Occasional Low engine RPM Run engine at full RPM Blades of Uncut Grass Ground speed too fast Slow speed to adjust for conditions Wet grass Cut grass after it has dried out Dull blades, incorrect sharpening Sharpen blades Deck plugged, grass accumulation Clean underside of deck Belts slipping Adjust belt tension Streaking - ...

  • Scag Power Equipment STT-31BSG - page 22

    Section 5 18 Uneven Cut on Flat Lift worn from blade Replace blade Ground - Wavy High-Low Blade upside down Mount with cutting edge toward Appearance, ground Scalloped Cut, or Rough Contour Deck plugged, grass accumulation Clean underside of deck Too much blade angle (deck pitch) Adjust pitch and level Deck mounted improperly See your authorized SC ...

  • Scag Power Equipment STT-31BSG - page 23

    Section 5 19 Scalping - Blades Low tire pressures Check and adjust pressures Hitting Dirt or Cutting Very Close to Ground speed too fast Slow speed to adjust for conditions the Ground Cutting too low May need to reduce ground speed, raise cutting height, change direction of cut, and/or change pitch and level Rough terrain May need to reduce ground ...

  • Scag Power Equipment STT-31BSG - page 24

    Section 6 20 ADJUSTMENTS 6.1 P ARKING BRAKE ADJUSTMENT WARNING: Do not operate the mower if the parking brake is not operable. Possible se vere injury could result. The parking brake linkage should be adjusted whenever the parking brake lever is placed in the “ENGAGE” position and the parking brake will not prevent the mower from moving. If the ...

  • Scag Power Equipment STT-31BSG - page 25

    Section 6 21 B . The steering control levers are in the full forward position and the mower pulls to one side or the other when traveling in a forward direction. (T racking Adjustment, See Page 22). Neutral Adjustment 1. Be sure the dump valve levers are in the run position and the steering control levers are in the neutral lock position. 2. W ith ...

  • Scag Power Equipment STT-31BSG - page 26

    Section 6 22 T racking Adjustment Stop the engine and remove the key from the ignition before making an y adjustments. W ait for all moving parts to come to a complete stop before beginning work. The engine and drive unit can get hot during operation causing burn injuries. Allow engine and drive components to cool before making any adjustments. -NO ...

  • Scag Power Equipment STT-31BSG - page 27

    Section 6 23 6.6 CUTTER DECK ADJUSTMENTS Cutter deck level, pitch and height are set at the factory . However , if these adjustments should ever need to be made, the following procedures will aid in obtaining the proper cutter deck adjustment. -NOTE- Befor e pr oceeding with the cutter deck adjustments, be sur e that all tir es ar e pr operly infla ...

  • Scag Power Equipment STT-31BSG - page 28

    Section 6 24 Cutter Deck Height The cutter deck height adjustment is made to ensure that the cutter deck is cutting at the height indicated on the cutting height index gauge. T o check for proper deck height, be sure that the mower is on a flat, level surface and the tires are properly inflated. 1. Place the cutter deck in the transport position. L ...

  • Scag Power Equipment STT-31BSG - page 29

    Section 6 25 2002 CCB MOUNTING HARD W ARE MOUNTING HARD W ARE Figure 6-8. Custom Cut Baffle 3. Move the Custom-Cut Baffle to desired position. (See Figures 6.9 through 6.1 1 for position). 4. Reinstall the mounting hardware as shown. (See Figures 6.10 though 6.1 1). T orque hardware to 39ft.lbs. Figure 6-9. 3" Custom Cut Baffle Position 2002 C ...

  • Scag Power Equipment STT-31BSG - page 30

    26 Section 7 MAINTENANCE 7.1 MAINTENANCE CHART - RECOMMENDED SER VICE INTER V ALS * Perform these maintenance procedures more frequently under extreme dusty or dirty conditions HOURS Break-In 8 40 10 0 200 500 Procedure Comments (First 10) X Check all hardware for tightness X Check hydraulic oil level See paragraph 7.3 X Check all belts for proper ...

  • Scag Power Equipment STT-31BSG - page 31

    Section 7 27 + Compatible Greases: Mobilix #2 found at Mobil Service Stations Ronex MP found at Exxon Service Stations Super Lube MEP #2 & Super Stay-M #2 found at Conoco Stations Shell Alvania #2 found at Shell Service Stations Lidok EP #2 found at industrial shops MAINTENANCE CHART - RECOMMENDED SER VICE INTER V ALS (CONT'D) HOURS Break- ...

  • Scag Power Equipment STT-31BSG - page 32

    28 Section 7 Figure 7.1 Lubrication Fitting P oints GREASE FITTING LUBRICATION LUBRICANT / INTERVAL LITHIUM MP WHITE GREASE 2125 ( 40 HOURS / WEEKLY ) CHASSIS GREASE ( 100 HOURS / BI-MONTHLY ) CHASSIS GREASE ( 200 HOURS / MONTHLY ) 4 1 6 6 3 3 5 7 7 2 CHASSIS GREASE ( 500 HOURS / YEARLY ) 390S0145-2 1 8 8 4 3 3 9 5 9 2 10 10 ...

  • Scag Power Equipment STT-31BSG - page 33

    Section 7 29 7.3 HYDRA ULIC SYSTEM A. Checking Hydraulic Oil Level The hydraulic oil level should be checked after the first 10 hours of operation. Thereafter , check the oil after every 200 hours of machine operation or monthly , whichever occurs first. -IMPORT ANT - If the oil level is consistently low , check for leaks and corr ect immediately . ...

  • Scag Power Equipment STT-31BSG - page 34

    30 Section 7 A. Checking Engine Crankcase Oil Level The engine oil level should be checked after every 8 hours of operation or daily as instructed in the Engine Operator ’ s Manual furnished with this mower (See Figure 7-4). B. Changing Engine Crankcase Oil After the first 5 hours of operation, change the engine crankcase oil and replace the oil ...

  • Scag Power Equipment STT-31BSG - page 35

    Section 7 31 7.5 ENGINE FUEL SYSTEM A. Filling the Fuel T ank Fill the fuel tank at the beginning of each operating day to within 1 inch below the filler neck. Do not overfill. Use clean, fresh unleaded gasoline with a minimum octane rating of 87. B. Replacing In-Line Fuel Filter Element -NOTE- The fuel filter is located below the hydraulic tank. F ...

  • Scag Power Equipment STT-31BSG - page 36

    32 Section 7 Electric storage battery fluid contains sulfuric acid which is POISON and can cause SEVERE CHEMICAL BURNS. A v oid contact of fluid with eyes, skin, or clothing. Use proper protective gear when handling batteries. DO NO T tip any battery bey ond 45° angle in any direction. If fluid contact does occur , follow fir st aid suggestions be ...

  • Scag Power Equipment STT-31BSG - page 37

    Section 7 33 WARNING: B A TTERIES PRODUCE EXPLOSIVE GASES. Charge the battery in a well ventilated space so gases produced while charging can dissipate. Charging rates between 3 and 50 amperes are satisfactory if excessive gassing or spewing of electrolyte does not occur or the battery does not feel excessively hot (over 125°F). If spewing or gass ...

  • Scag Power Equipment STT-31BSG - page 38

    34 Section 7 Figure 7-9 Blade Sharpening 2. Check the balance of the blade. If the blades are out of balance, vibration and premature wear can occur . See your authorized Scag dealer for blade balancing or special tools, if you choose to balance your own blades. C. Blade Replacement 1. Remove the ignition key before replacing the blades. 2. Raise t ...

  • Scag Power Equipment STT-31BSG - page 39

    Section 7 35 The cutter deck gearbox can reach high operating temperatures. Allow the cutter deck gearbox to cool before servicing. CAUTION: 7.11 CUTTER DECK GEARBO X A. Checking Lubricant Level The fluid level in the cutter deck gearbox (Figure 7-12) should be checked after every 100 hours of operation or bi-weekly , whichever occurs first. 1. Low ...

  • Scag Power Equipment STT-31BSG - page 40

    36 Section 7 3. Replace the radiator cap. Push down on the cap and turn clockwise until it stops. -NOTE- The cooling system should be flushed and the coolant r eplaced every 500 hours of op- eration or annually. See your Scag dealer for proper coolant replacement. B. Cleaning the Radiator Debris Screen After each day of operation, remove and clean ...

  • Scag Power Equipment STT-31BSG - page 41

    37 NOTES ...

  • Scag Power Equipment STT-31BSG - page 42

    38 61A, 72A CUTTER DECKS 44 61 63 69 62 12 65 64 52 58 54 17 59 24 14 56 28 56 33 3 A A B B 4 14 29 20 53 28 52 24 58 24 52 66 32 13 68 55 55 29 58 2 3 13 23 57 3 11 50 13 46 60 49 67 24 35 48 9 16 19 15 27 26 12 47 51 23 23 36 37 44 39 43 42 38 45 41 34 72 22 40 37 18 10 1 5 7 68 STT-BSG 2002 CD 14 29 12 30 28 31 25 31 21 22A B 3 B 56 32 30 70 51 ...

  • Scag Power Equipment STT-31BSG - page 43

    39 Ref. Part No. No. Description Ref. Part No. No. Description 42 43297 Spindle Bushing, Bottom 43 481035 Nut, Special 1 - 1/16-18 44 48114-04 Grease Fitting 45 48677 Relief Fitting, Tapered Spindle 46 482245 Spring, Discharge Chute 47 48038 Guide, Roller 48 482001 Cutter Blade, 21.0” 61” 48 482002 Cutter Blade, 24.5" 72” 49 482486 Gearb ...

  • Scag Power Equipment STT-31BSG - page 44

    40 CUTTER DECK CONTROLS STT2002CDC 21 19 37 42 4 6 14 10 42 5 2 3 35 23 41 38 32 34 30 7 27 33 40 41 28 28 24 26 41 40 CUTTER DECK 13 40 39 31 41 40 39 43 9 8 45 20 18 36 16 44 17 41 40 26 11 29 22 40 41 15 22 41 7 1 40 24 12 26 29 41 25 ...

  • Scag Power Equipment STT-31BSG - page 45

    41 CUTTER DECK CONTROLS Ref. Part No. No. Description 1 04041-07 Flatwasher, 3/8” 2 481764 Link, Deck Lift 3 481765 Rod End, Female - 1/2-20 RH 4 481766 Rod End, Female - 1/2-20 LH 5 04020-27 Nut, Jam 1/2-20 RH 6 04020-28 Nut, Jam 1/2-20 LH 7 04021-09 Nut, 3/8-16 Elastic Stop 8 482429 Slide Weldment, Height Adjustment 9 43391 Spacer, Decklift Ped ...

  • Scag Power Equipment STT-31BSG - page 46

    42 SHEET MET AL COMPONENTS STT-BSG 2002 SMC 46 48 47 48 15 50 26 30 25 12 15 19 9 1 23 24 A 31 32 33 34 29 33 36 37 40 39 38 41 42 43 55 35 44 15 27 22 54 20 28 15 14 13 12 11 10 16 17 A 20 5 3 4 8 7 18 18 56 57 58 54 6 51 53 52 49 45 15 12 61 64 59 62 15 63 12 60 ...

  • Scag Power Equipment STT-31BSG - page 47

    43 SHEET MET AL COMPONENTS Ref. Part No. No. Description 1 451481 Fender Weldment, RH 2 04001-09 Bolt, Hex Head, 5/16-18 x 1, Zinc 3 43 606 Spacer 4 04041-07 Flatwasher, 3/8-.391 x .938 x .105 5 451448 Seat Plate Weldment 6 482597 Seat Assembly w/armrest 7 04001-45 Bolt, Hex Head 3/8-16 x 2.0” 8 04021-09 Nut, Elastic Stop 3/8-16 9 482283 Battery ...

  • Scag Power Equipment STT-31BSG - page 48

    44 DECK DRIVE COMPONENTS A To A B To B TO REAR OF ENGINE TO ENGINE FL YWHEEL 1 2 3 4 5 6 7 8 9 4 10 11 12 13 14 15 16 17 18 19 20 21 22 22 23 24 24 25 25 26 27 27 28 29 30 31 32 33 34 35 36 37 38 42 40 41 39 43 43 35 44 44 45 46 47 43 48 35 49 50 51 52 53 43 55 54 43 55 45 57 43 58 48 49 35 59 59 60 61 59 62 63 64 65 65 35 35 65 35 66 59 67 68 42 4 ...

  • Scag Power Equipment STT-31BSG - page 49

    45 1 422845 Belt Guard, Rear 2 481531 Hinge, Rear Belt Guard 3 481309 Latch, Hood 4 04003-07 Carr. Bolt 1/4-20 x .5” 5 04019-02 Nut, Serr. Flg. 1/4-20 6 04010-01 Screw, #10-32 x .5, Phillips Head 7 04031-01 Lock Washer, #10 8 04020-01 Nut, #10-32 9 451457 Weldment, Pump Mounting 10 43506 Spacer, Engine 11 43507 Stud, Anti-Rotation 12 482433 Linka ...

  • Scag Power Equipment STT-31BSG - page 50

    46 RADIA T OR, COOLERS & ENGINE BRA CKETS T O "A" A A TT ACHES TO FRAME 17 22 21 12 13 15 2 9 1 5 11 10 10 6 7 20 19 14 14 3 18 16 16 8 23 24 25 26 27 28 29 30 31 32 34 35 26 26 36 37 26 26 37 38 39 40 36 26 41 42 42 33 4 24 ...

  • Scag Power Equipment STT-31BSG - page 51

    47 1 481810 Radiator 2 481742 Hose, Upper Radiator 3 481743 Hose, Lower Radiator 4 04030-03 Lockwasher, 5/16 (.317 x .586 x .078) Helical Spring 5 423628 Bracket, Air Cleaner 6 423539 Bracket, Engine Mounting LH 7 423540 Bracket, Engine Mounting RH 8 422702 Bracket, Radiator Mounting 9 422704 Shroud, Radiator 10 422696 Plate, Engine Mounting 11 481 ...

  • Scag Power Equipment STT-31BSG - page 52

    48 BRAKE AND STEERING COMPONENTS STT2002B&SC A 1 2 10 11 33 17 9 19 23 41 11 21 34 36 57 73 48 47 46 5 23 53 42 43 44 45 15 56 70 69 71 62 15 65 60 64 67 60 52 41 34 23 51 50 34 35 TO RH PUMP TO LH PUMP 37 36 27 28 35 33 78 34 31 30 29 8 9 6 32 13 B 9 B 25 18 72 49 55 54 5 3 4 75 26 58 76 5 68 66 37 36 61 59 74 7 20 13 14 22 14 39 16 24 38 63 2 ...

  • Scag Power Equipment STT-31BSG - page 53

    49 1 482340 Grip, Handle Bar 2 461386 Handle Bar (Includes item 1) 3 04001-32 Bolt, Hex Head 3/8-16 x 1-1/4" 4 04030-04 Lockwasher, 3/8" 5 04041-07 Flatwasher. 3/8" (.391 x .938 x .105) 6 422372 Bar, Control Lever 7 451483 Control Lever Weldment, LH 451484 Control Lever Weldment, RH 8 04001-17 Bolt, Hex Head 5/16-18 x 2" 9 04021 ...

  • Scag Power Equipment STT-31BSG - page 54

    50 FUEL AND HYDRA ULIC SYSTEM D D D E F C I H G G F E A A B C DUMP VALVE B 2002 STT -BSG F&HS.eps I H T o Carburetor 39 13 14 15 23 24 26 40 16 17 32 36 37 Z 34 25 35 21 31 33 9 30 30 57 56 54 7 4 4 3 44 45 50 46 51 53 52 49 4 4 2 42 34 25 35 55 18 8 20 19 6 22 41 27 28 29 30 38 Z 2 2 5 58 59 7 7 22 4 4 43 (2) 43 (2) 7 1 T o Back Side of Reserv ...

  • Scag Power Equipment STT-31BSG - page 55

    51 FUEL AND HYDRA ULIC SYSTEM 1 04110-01 U-Nut 1/4-20 2 48136-13 Hose Clamp, 0.69 dia. 3 04001-03 Bolt, Hex Head 1/4-20 x 2.0” 4 48811 Hose, 3/8” ID Pushlock - (order by inch) 5 482505 Cooler, Oil 6 482266-01 Elbow, 90 Degree - 9/16 O-ring x 3/8 Hose 7 482266-02 Elbow, 90 Degree - 3/4 O-ring x 3/8 Hose 8 48471-02 Oil Filter Base 9 482563 Hose A ...

  • Scag Power Equipment STT-31BSG - page 56

    52 ELECTRICAL SYSTEM B A C C B A 1 2 3 4 5 6 7 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 22 21 20 20 20 24 25 24 25 24 25 26 22 21 22 21 27 27 1 2 19 28 29 30 31 32 33 34 35 36 36 37 D D 19 38 ELECTRICAL SYSTEM ...

  • Scag Power Equipment STT-31BSG - page 57

    53 1 4811 76- 08 Cable, Positive Battery 2 4811 76- 07 Cable, Negative Battery 3 461467 Clutch, Electric PTO 4 481808 Module, Interlock 5 482283 Battery (Not Avail. through Scag, Exide P/N 26R) 6 481687 Switch, PTO 7 48798 Switch, Key (Includes Nut and Lockwasher) 48017-03 Nut, 5/8-32 Special 48017-04 Lock Washer 5/8” 8 481806 Cable, Control (Thr ...

  • Scag Power Equipment STT-31BSG - page 58

    54 HYDRAULIC PUMP ASSEMBLY STT 2K BDP-21 11 4 9 11 2 12 10 6 8 7 18 5 14 17 19 20 22 21 23 24 16 25 26 28 27 3 Overhaul Seal Kit 1 3 25 13 15 HYDRA ULIC PUMP ASSEMBL Y - BDP-21L ...

  • Scag Power Equipment STT-31BSG - page 59

    55 1 HG 2510065 Housing Kit (Includes Housing, Journal Bearing) 2 HG 2510066 End Cap 3 HG 50641 Straight Headless Pin 4 HG 50633 Socket Head Screw 5 HG 50381 End Cap Gasket 6 HG 2510071 Charge Pump Kit (Includes Charge Cover, Gerotor Assy., O-Ring) 7 HG 50406 Gerotor Assembly 8 HG 9004100-1430 O-Ring 9 HG 70402 Charge Relief Valve Kit 10 HG 9007200 ...

  • Scag Power Equipment STT-31BSG - page 60

    56 RED RED BLUE BLK RED RED PINK ORG BRN PINK RED RED BLUE BLK RED RED RED ORG L T BLUE BRN L T BLUE WHITE W/RED GRN W/BLK GRN W/WHITE GRN RED RED BLK BLK RED RED RED RED RED RED ORG BRN BLK BLK BLK GRN W/WHITE WHITE W/BLK BLK W/ WHITE BLK YEL YEL INTERLOCK MODULE PTO SWITCH VO LT METER IGNITION SWITCH OIL PRESSURE GA UGE W A TER TEMP GA UGE 20 AMP ...

  • Scag Power Equipment STT-31BSG - page 61

    57 REPLA CEMENT DECALS AND INFORMA TION PLA TES 482285 482286 481955 - 61A 481956 - 71A 48656 48404 481568 482290 4 81039 482507 482565 482580 481971 WARNING INSTALL BELT COVER BEFORE OPERATING MACHINE READ OPERATOR'S MANUAL 481039 FORWARD REVERSE F R 481669 481669 PULL OUT TO ENGAGE ON ST ART PUSH IN TO DISENGAGE OFF MOWER DECK STT-31BSG Deca ...

  • Scag Power Equipment STT-31BSG - page 62

    58 REPLA CEMENT DECALS AND INFORMA TION PLA TES 481921 R 481921 STT-31BSG Decals 2 481925 481664 481663 482710 481663 481664 481921 481937 48314 48825 482165 ...

  • Scag Power Equipment STT-31BSG - page 63

    LIMITED W ARRANTY - COMMERCIAL EQUIPMENT Any part of the Scag commercial mower manufactured by Scag Power Equipment and found, in the reasonable judgment of Scag, to be defective in materials or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor . This warranty is limited to the origina ...

  • Scag Power Equipment STT-31BSG - page 64

    P ART NO. 03121 PRINTED 7/02 PRINTED IN USA © 2002 SCAG POWER EQUIPMENT DIVISION OF MET ALCRAFT OF MA YVILLE, INC. ...

Manufacturer Scag Power Equipment Category Lawn Mower

Documents that we receive from a manufacturer of a Scag Power Equipment STT-31BSG can be divided into several groups. They are, among others:
- Scag Power Equipment technical drawings
- STT-31BSG manuals
- Scag Power Equipment product data sheets
- information booklets
- or energy labels Scag Power Equipment STT-31BSG
All of them are important, but the most important information from the point of view of use of the device are in the user manual Scag Power Equipment STT-31BSG.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Scag Power Equipment STT-31BSG, service manual, brief instructions and user manuals Scag Power Equipment STT-31BSG. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Scag Power Equipment STT-31BSG.

Similar manuals

A complete manual for the device Scag Power Equipment STT-31BSG, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Scag Power Equipment STT-31BSG by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Scag Power Equipment STT-31BSG.

A complete Scag Power Equipment manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Scag Power Equipment STT-31BSG - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Scag Power Equipment STT-31BSG, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Scag Power Equipment STT-31BSG, that we can find in the current document
3. Tips how to use the basic functions of the device Scag Power Equipment STT-31BSG - which should help us in our first steps of using Scag Power Equipment STT-31BSG
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Scag Power Equipment STT-31BSG
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Scag Power Equipment STT-31BSG in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Scag Power Equipment STT-31BSG?

Use the form below

If you did not solve your problem by using a manual Scag Power Equipment STT-31BSG, ask a question using the form below. If a user had a similar problem with Scag Power Equipment STT-31BSG it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)