English dropdown-ico

Manual AquaStar 125X

13 pages 0.16 mb
Download

Go to site of 13

Summary
  • AquaStar 125X - page 1

    INST ALLA TION AND OPERA TING INSTRUCTIONS FOR AQ-1 POWER VENT KIT DESIGNED FOR BOSCH 425 HN W A TER HEA TERS AQUAST AR 125 B W A TER HEA TERS INCLUDING AQUAST AR MODELS: 125HX • 125BS • 125X • 125BL T ABLE OF CONTENTS contents with an AQ-1 power vent p. 1 mounting gas pressure switch p. 2 mounting linear spillage switch p.4 common setup p. 6 ...

  • AquaStar 125X - page 2

    AQ-1 Power vent kit Parts included: Spillage Switch Kit 1. 185º F linear spillage switch mounted on an angled bracket and equipped with 36 inch cables connected to one eyelet terminal and one 1/4" quick connect terminal 2. Spillage switch mounting screw 3. Push on male spade connector , replaces eyelet terminal from 36 inch spill switch cable ...

  • AquaStar 125X - page 3

    Power V ent Kit CAUTION 1. Failure to install, maintain and/or operate the Power V enter in accordance with manufacturer's instruction may result in conditions which can produce bodily injury and property damage. 2. The Power V enter must be installed by a qualified installer in accordance with all local codes or , in their absence, in accorda ...

  • AquaStar 125X - page 4

    INSTRUCTIONS ( SEE DIAGRAMS ABOVE ) 1. Mount gas pressure switch by securing it to the chosen location with a screw in each one of the four mounting holes. 2. Use a tube cutter to make a clean cut (not crimped) at each end of the two lengths of the 1/4" aluminum tubing. One tube must be long enough to reach from the fitting marked "connec ...

  • AquaStar 125X - page 5

    e. Hand thread the pressure tap fitting into the heater's burner manifold. Use a small amount of an appropriate thread sealant on the male end of the fitting. Over tightening of the fitting will break it. f. Guide the end of the tube into the com- pression fitting. While using one wrench to hold back the pressure tap fitting, gently snug- up t ...

  • AquaStar 125X - page 6

    1. The ECO is mounted on the lower left outlet water pipe. (See figure C) a. Remove one lead connecting to ECO terminal, it does not matter which one is disconnected. b. Attach 1/4" quick connect terminal end of linear spill switch cable to now exposed terminal of the ECO. c. Remove the eyelet ended terminal from the other spill switch cable. ...

  • AquaStar 125X - page 7

    COMMON SETUP Mount gas pressure switch against wall 6 125B Model shown See Figure D, page 5 for location of Linear S pillage Switch V ent Hood (see freeze prevention information on page 2) Power vent motor 4" single wall pipe* (galvanized or stainless steel) or 4" B-type vent*. * Single wall vent pipe requires a 6" clearance to combu ...

  • AquaStar 125X - page 8

    CAUTION Failure to follow these installation instructions may violate applicable national and/or local codes The vent system must terminate so that proper clearances are maintained as cited in the National Fuel Gas Code, ANSI Z223.1 "The exit terminals of mechanical vent system shall be located not less than 7 feet above grade when located adj ...

  • AquaStar 125X - page 9

    INSTRUCTIONS (DO NOT BEGIN THESE PROCEDURES UNTIL VENT HOOD HAS BEEN INST ALLED) 1. Remove vibration mounts, nuts and washers from parts bag. Install on power venter as shown in (Figure H). 2. T o prevent vibration, securely support power venter from ceiling or joist using a plumber's strap or wire fastened to the vibration mounts. As an alter ...

  • AquaStar 125X - page 10

    3. Connect the RED wire from the jacketed cable onto the common terminal of the gas pressure switch. (See Figure I) NOTE: If the distance between the power venter and the gas pressure switch is greater than the length of the cable, splice a section of 2 conductor , PVC sheathed, 105º C thermostat cable to the supplied cable. Make sure that the col ...

  • AquaStar 125X - page 11

    SAFETY INTERLOCK TEST 1. Open the gas supply to the water heater . 2. Remove the vent pipe from the vent connec- tor on the top of the water heater . 3. Block the vent connector with sheet metal or other noncombustible material. 4. Turn on the hot water supply to allow the burner to activate. Hot flue gasses will spill from the draft diverter momen ...

  • AquaStar 125X - page 12

    11 HEA TER ECO SAFET Y INTERLOCK DIAGRAM LINEAR LIMIT SPILLAGE SENSING SWITCH 185º MANUAL RESET BLACK ...

  • AquaStar 125X - page 13

    1. Attach this template to the interior of the wall the V ent Hood will be penetrating. 2. Insure that proposed vent termination clear- ances are met before cutting opening through wall. Using a 1/2" drill bit, drill two pilot holes where noted on this template. The drill bit must be long enough to penetrate to the building exterior . 3. Attac ...

Manufacturer AquaStar Category Water Heater

Documents that we receive from a manufacturer of a AquaStar 125X can be divided into several groups. They are, among others:
- AquaStar technical drawings
- 125X manuals
- AquaStar product data sheets
- information booklets
- or energy labels AquaStar 125X
All of them are important, but the most important information from the point of view of use of the device are in the user manual AquaStar 125X.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals AquaStar 125X, service manual, brief instructions and user manuals AquaStar 125X. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product AquaStar 125X.

Similar manuals

A complete manual for the device AquaStar 125X, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use AquaStar 125X by users. Manuals are usually written by a technical writer, but in a language understandable to all users of AquaStar 125X.

A complete AquaStar manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual AquaStar 125X - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the AquaStar 125X, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the AquaStar 125X, that we can find in the current document
3. Tips how to use the basic functions of the device AquaStar 125X - which should help us in our first steps of using AquaStar 125X
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with AquaStar 125X
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of AquaStar 125X in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning AquaStar 125X?

Use the form below

If you did not solve your problem by using a manual AquaStar 125X, ask a question using the form below. If a user had a similar problem with AquaStar 125X it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)