Manual Vivitek D927TW

59 pages Not applicable
Download

Go to site of 59

Summary
  • Vivitek D927TW - page 1

    Copyright This publication, including all photographs, illustratio ns and software, is protected under international copy- right laws, with all rights reserved. Neither this man ual, nor any of the material contained herein, may be reproduced without written consent of the autho r. © Copyright 2009 Disclaimer The information in this document is su ...

  • Vivitek D927TW - page 2

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l — ii — Important Safety Information Important: It is strongly recommended that you read this sect ion carefully be fore using the projector. These safety and usage instructions will en ...

  • Vivitek D927TW - page 3

    P P P r r r e e e f f f a a a c c c e e e Projector Installation Notice ¾ Place the projector in a horizontal p osition The tilt angle of the projector should not excee d 15 degrees, nor should the proje ctor be installed in any way other than the desktop and ceiling mou nt, ot herwise lamp life could decrease dramatically. ¾ Allow at least 50 cm ...

  • Vivitek D927TW - page 4

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Replacing the Lamp Replacing the lamp can b e hazardous if done in correctly. See Replacing the Proje ction Lamp on page 39 for clear and safe instructi ons for this procedure. Before repl ...

  • Vivitek D927TW - page 5

    P P P r r r e e e f f f a a a c c c e e e – v – Table of Contents GETTING STARTED .......................................................................................................................................................... 1 P ACKING C HECKLIST ....................................................................................... ...

  • Vivitek D927TW - page 6

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l — vi — H AVING THE P ROJECTOR S ERVICED ............................................................................................................................... ... 47 SPECIFICA ...

  • Vivitek D927TW - page 7

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 1 – G ETTING S TARTED Packing Checklist Carefully unpack the projector and che ck that the following items are included: D9 SERI ES DLP P ROJECTOR R EMOTE CONTROL (WITH TWO AAA BATTE ...

  • Vivitek D927TW - page 8

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Views of Projector Parts D9 SERIES Front-right View I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Height-adj uster butto n Push to release height adjust er 2. Height adjuster Adjusts level of ...

  • Vivitek D927TW - page 9

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Top view—On-screen Display (OSD) buttons and LEDs I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. (Power button) Turns the projector O n or Off. 11 2. BLANK Displays a bl ank screen a nd mut e ...

  • Vivitek D927TW - page 10

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Rear view I TEM L ABEL D ESCRIPTIO N S EE PAGE : 11 1. AC IN Connect the POWER CABLE 2. Connect the USB CABL E from a computer (USB) Connect the RGB CABLE to a disp lay (Loop Thru only for ...

  • Vivitek D927TW - page 11

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Bottom view I TEM L ABEL D ESCRIPTIO N S EE PAGE : 15 1. Tilt adjustor Rotate adju ster lever to adjust angle po sition. 2. Ceiling support ho les Contact your dealer for in formation on m ...

  • Vivitek D927TW - page 12

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Remote Control Par ts Important: 1. Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. ...

  • Vivitek D927TW - page 13

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 7 – I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. IR transmitter Transmit s signals t o projector 2. Status LED Lights w hen the remote control is used 3. Laser Press to operate the on-s ...

  • Vivitek D927TW - page 14

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 8 – Remote Control Operating Range The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the remote directly at the projector. Provide ...

  • Vivitek D927TW - page 15

    S ETUP AND O PERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow. 2. Insert the battery with the positive side facing up. 3. Replace the cover. Caution: 1. Only use AAA batteries (Alkaline batteries are recommended). 2. Dispose of used batteries accordi ng to loc ...

  • Vivitek D927TW - page 16

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Connecting Input Devices A PC or note book computer and video devices can be connected to the projector at the same time. Video devices include DVD , VCD, and VHS players, as we ll as movi ...

  • Vivitek D927TW - page 17

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Starting and Shutting down t he Projec tor 1. Connect the power cord to the projector. Connect the other end to a wall outlet. The POWER and READY LEDs on the projector light. 2. Turn on t ...

  • Vivitek D927TW - page 18

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l 5. When the “Power Off? /Press Power again” message appears, press the POWER button. The projector turns off. Caution: 1. Be sure to remove the lens cap before starting projector. 2. D ...

  • Vivitek D927TW - page 19

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Setting an Access Password (Security L ock) You can use the four (arrow) buttons to set a password and pr event un authorized use of the projector. When enabled, the password must be enter ...

  • Vivitek D927TW - page 20

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l 5. You can use the cursor buttons ▲▼◄► either on keypad or IR remote control for password entry. You can use any combination including the same arrow five times, but not less than ...

  • Vivitek D927TW - page 21

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Adjusting the Projector Level Take note of the following when setting up the projector: • The projector t able or stand should be level and sturdy . • Position the projector so that it ...

  • Vivitek D927TW - page 22

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Adjusting the Zoom ring (VX Series only) , Focus and Key stone – 16 – 1. Use the Image-zoom control (on the projector only) to resize the pro- jected image and screen size B . 2. Use t ...

  • Vivitek D927TW - page 23

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Adjusting the Volume 1. Press the Volume +/- buttons on the remote control. The volume control appears on the display. 2. Press the Left or Right Cursor buttons on the keypad to adjust Vol ...

  • Vivitek D927TW - page 24

    O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you ma ke image adjustments and c hange various settings. Navigating the OSD You can use the remote control curs or buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The following illu stration shows the corresp ...

  • Vivitek D927TW - page 25

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Setting the OSD Language Set the OSD language to your pr eference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to Installation I. 2. Press the cu ...

  • Vivitek D927TW - page 26

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l OSD Menu Overview Use the following illustration to quickly find a se tting or determine the range for a setting. – 20 – ...

  • Vivitek D927TW - page 27

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l OSD Sub-Menu Overvie w – 21 – ...

  • Vivitek D927TW - page 28

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Image Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image Menu . Press the cursor ▲▼ button to move up and down in the Image menu. Pres ...

  • Vivitek D927TW - page 29

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Advanced menu and then press Enter or ► . Press ▼▲ to ...

  • Vivitek D927TW - page 30

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Color Manager (Enter) / ► to enter the Color Manager sub menu. Press I TEM D ESCRIPTIO N Select to enter the Red Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, an ...

  • Vivitek D927TW - page 31

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Computer Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Com- puter menu. Press the cursor ▲▼ button to move up and down in the computer ...

  • Vivitek D927TW - page 32

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Video/Audio Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Video/Audio menu. Press the cursor ▲▼ button to move up and down in the Video ...

  • Vivitek D927TW - page 33

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Audio (Enter) / ► to enter the Audio sub menu. Press I TEM D ESCRIPTIO N Press the ◄► butt ons to ad just the audi o volum e. (Range: 0 ~ 8) Volum e Mute Press the ◄► buttons to ...

  • Vivitek D927TW - page 34

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Installation I Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installa- tion I menu. Press the cursor ▲▼ button to move up and down in t ...

  • Vivitek D927TW - page 35

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Installation II Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installa- tion II menu. Press the cursor ▲▼ button to move up and down in ...

  • Vivitek D927TW - page 36

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Installation II menu. Press ▲▼ to move to the Advanced menu and then press Enter or ► . Press ...

  • Vivitek D927TW - page 37

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l OSD Menu Setting I TEM D ESCRIPTIO N Menu Position Press ◄► button to select diffe rent OSD locati on. Translucent Menu Press ◄► butt on to select O SD backgroun d translucent le v ...

  • Vivitek D927TW - page 38

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Lamp Hour Reset Please refer to Resetting the Lamp on page 41 to reset the lamp hour counter. Network I TEM D ESCRIPTIO N Network State Displays the network conn ection status. Press ◄? ...

  • Vivitek D927TW - page 39

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l For simplicity and ease of operatio n, the projector provides di verse networking and remot e manage- ment features. The LAN/RJ45 function of the projector through a network, such as remot ...

  • Vivitek D927TW - page 40

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l 3. Right-click on Local Area Connection , and select Properties . 4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP) . 5. Click Properties . 6. Clic ...

  • Vivitek D927TW - page 41

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l 7. Press the Menu button on the projector. 8. Select Installation II ´ Advanced ´ Network . 9. After getting into Network , input the following: ` DHCP: Off ` IP Address: 192.168.10.10 ` ...

  • Vivitek D927TW - page 42

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l 14. Click Control Panel to display projector settings. Preparing Email Alerts 1. Make sure that user can access the hom epage of LAN RJ45 function by web browser (for ex- ample, Microsoft ...

  • Vivitek D927TW - page 43

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l 4. The To field is the recipients email address (for example, projector administrator). This is a required field. The Cc field sends a carbon copy of the alert to the specified email addre ...

  • Vivitek D927TW - page 44

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Factory Reset Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the Factory Reset sub menu and press (Enter) / ► to reset all the menu items to the f ...

  • Vivitek D927TW - page 45

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 39 – M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified replacement part, ...

  • Vivitek D927TW - page 46

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 40 – 3. Remove the three screws from the lamp module. 4. Lift the module handle up. 5. Pull firmly on the module handle to remove the lamp module. 6. Reverse steps 1 to 5 to install ...

  • Vivitek D927TW - page 47

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Resetting the Lamp After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 1. Press the MENU button to open the OSD menu. 2. Press the cursor ◄? ...

  • Vivitek D927TW - page 48

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 42 – Cleaning the Projector Cleaning the projector to remove dust and gr ime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at leas ...

  • Vivitek D927TW - page 49

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Using the Kensingt on ® Lock If you are concerned about security, attach the proj ector to a permanent obje ct with the Kensington slot and a security cable. Note: Contact your vendor for ...

  • Vivitek D927TW - page 50

    T ROUBLESHOOTING Common problems and solut ions These guidelines provide tips to deal with problem s you may encounter while using the projector. If the problem remains unsolved, cont act your dealer for assistance. Often after time spent troubleshooting, the problem is traced to something as simple as a loose con- nection. Check the following befo ...

  • Vivitek D927TW - page 51

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 45 – LED Error Messages E RROR C ODE M ESSAGE S P OWER LED B LINK R EADY LED B LINK T EMP LED B LINK Over temperature OFF OFF ON G794 fail 4 4 OFF T1 fail 4 5 OFF Lamp error 5 OFF OF ...

  • Vivitek D927TW - page 52

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 46 – 3. Ensure the projector-to-screen distance is within the 10-meter (33-feet) spe cified range. 4. Check that the projector lens is clean. Problem: The image is wider at the top o ...

  • Vivitek D927TW - page 53

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 47 – Audio Problems Problem: There is no sound 1. Adjus t the volume on the remote control. 2. Adjust the volume of the audio source. 3. Check the audio cable connection. 4. Test the ...

  • Vivitek D927TW - page 54

    — 48 — S PECIFICATIONS Specifications Model D935VX D940 VX/D945VX D930TX D925TX D927TW Display type TI DMD 0.55” XGA TI DMD 0.7” XGA TI DMD 0.55” XGA TI DMD 0.65” WXGA Native Resolution XGA 1024x768 XGA 1024x 768 XGA 10 24x768 WXGA 1280x8 00 Weight 3.5 kg (7. 7 lbs) 3.6 kg (7. 9 lbs) Projection distance 1 meters ~ 10 mete rs 0.5 met ers ...

  • Vivitek D927TW - page 55

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 49 – Projection Distance vs. Projection Si ze D9 SERIES Projection Distance and Size Table D935VX T ELE W IDE Distance (m) 1.34 3.58 4. 47 8.94 1.54 3.09 3.86 11.58 Diagonal (inches) ...

  • Vivitek D927TW - page 56

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 50 – D9 SERIES Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. S IGNAL R ESOLUTI ...

  • Vivitek D927TW - page 57

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 51 – S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB ( ANALOG ) DVI/ HDMI ( DIGITAL ) 720p 37.5 50.0 — O — O 720p 45.0 60.0 — O — O 10 ...

  • Vivitek D927TW - page 58

    D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Projector Dimensions – 52 – ...

  • Vivitek D927TW - page 59

    R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply wi th the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules. These lim its are designed to provide reasonable protection against harmful interference when the equipm ent is operated in a commercial environment. This equipment generates, u ...

Manufacturer Vivitek Category Video projector

Documents that we receive from a manufacturer of a Vivitek D927TW can be divided into several groups. They are, among others:
- Vivitek technical drawings
- D927TW manuals
- Vivitek product data sheets
- information booklets
- or energy labels Vivitek D927TW
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vivitek D927TW.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vivitek D927TW, service manual, brief instructions and user manuals Vivitek D927TW. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vivitek D927TW.

Similar manuals

A complete manual for the device Vivitek D927TW, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vivitek D927TW by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vivitek D927TW.

A complete Vivitek manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vivitek D927TW - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vivitek D927TW, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vivitek D927TW, that we can find in the current document
3. Tips how to use the basic functions of the device Vivitek D927TW - which should help us in our first steps of using Vivitek D927TW
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vivitek D927TW
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vivitek D927TW in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vivitek D927TW?

Use the form below

If you did not solve your problem by using a manual Vivitek D927TW, ask a question using the form below. If a user had a similar problem with Vivitek D927TW it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)