English dropdown-ico

Manual Paradyne 3800PLUS

192 pages 1.31 mb
Download

Go to site of 192

Summary
  • Paradyne 3800PLUS - page 1

    COMSPHERE 3800 P LUS MODEMS USER’S GUIDE Document No. 3980-A2-GB30-20 November 1996 ...

  • Paradyne 3800PLUS - page 2

    COMSPHERE 3800 Plus Modems A November 1996 3980-A2-GB30-20 COMSPHERE 3800 Plus Modems User ’ s Guide 3980-A2-GB30-20 3rd Edition (November 1996) Changes and enhancements to the product and to the information herein will be documented and issued as a new release to this manual. For the 3810 Plus and 3820 Plus standalone modems the Universal Servic ...

  • Paradyne 3800PLUS - page 3

    Safety Instructions B 3980-A2-GB30-20 November 1996 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these slots and ...

  • Paradyne 3800PLUS - page 4

    COMSPHERE 3800 Plus Modems C November 1996 3980-A2-GB30-20 Notices      ? ...

  • Paradyne 3800PLUS - page 5

    Government Requirements D 3980-A2-GB30-20 November 1996 3. The Ringer Equivalence (REN) is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exce ...

  • Paradyne 3800PLUS - page 6

    COMSPHERE 3800 Plus Modems E November 1996 3980-A2-GB30-20 Canada Notice to Users of the Canadian Public Switched T elephone Network The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The ...

  • Paradyne 3800PLUS - page 7

    i 3980-A2-GB30-20 November 1996 T able of Contents Preface Objectives and Reader Assumptions vii . . . . . . . . . . . . . . . . . . . . . . . . . . . How to Use This Manual vii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related Documents vii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 8

    COMSPHERE 3800 Plus Modems ii November 1996 3980-A2-GB30-20 4. Front Panel Operation Overview 4-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diagnostic Control Panels 4-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status Indicators 4-2 . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 9

    T able of Contents iii 3980-A2-GB30-20 November 1996 12. Fax Operation Overview 12-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fax Operation 12-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13. A T Command Set and S-Registers Overview 13-1 . . . . . ...

  • Paradyne 3800PLUS - page 10

    COMSPHERE 3800 Plus Modems iv November 1996 3980-A2-GB30-20 List of Figures Figure Page 2-1 3810 Plus and 3820 Plus Modem 2-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 3810 Plus Rear Panel 2-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 3820 Plus Rea ...

  • Paradyne 3800PLUS - page 11

    T able of Contents v 3980-A2-GB30-20 November 1996 List of T ables T able Page 4-1 3800 Plus DCP LEDs 4-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 SDCP LEDs 4-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 T op Level M ...

  • Paradyne 3800PLUS - page 12

    vii 3980-A2-GB30-20 November 1996 Preface Objectives and Reader Assumptions This manual describes how to install and operate the 3810 Plus , 3820 Plus (standalone), and 381 1 Plus (carrier-mounted) modems. The reader is assumed to have a basic understanding of modems and their operation. How to Use This Manual Chapter 1 provides information about t ...

  • Paradyne 3800PLUS - page 13

    1-1 3980-A2-GB30-20 November 1996 Introduction Overview 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 14

    COMSPHERE 3800 Plus Modems 1-2 November 1996 3980-A2-GB30-20 • Class 1 and Class 2 Group III Fax modulations: CCITT V .17 (14,400, 12,000, 9600, and 7200 bps), V .29 (9600 and 7200 bps), and V .27ter (4800 and 2400 bps). • Convenient migration to new or optional features through software downloading. • CCITT V .42bis and MNP Class 5 data comp ...

  • Paradyne 3800PLUS - page 15

    2-1 3980-A2-GB30-20 November 1996 3810 Plus and 3820 Plus Installation Overview 2-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3810 Plus and 3820 Plus Modem Package 2-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 16

    COMSPHERE 3800 Plus Modems 2-2 November 1996 3980-A2-GB30-20 DIAGNOSTIC CONTROL LCD AND ST A TUS POWER SUPPL Y 496-14678-01 POWER ON/OFF LEASED (3810 Plus ONL Y) DIAL (OR LEASED FOR 3820 Plus ) DTE 1 NMS POWER IN Figure 2-1. 3810 Plus and 3820 Plus Modem Customer-Supplied Equipment The following customer -supplied equipment may be required to compl ...

  • Paradyne 3800PLUS - page 17

    3810 Plus and 3820 Plus Installation 2-3 3980-A2-GB30-20 November 1996 • An 8-pin modular keyed jack for 4-wire/2-wire leased lines (3810 Plus only). • An 6-pin modular keyed jack for dial (PSTN) lines (and, for 3820 Plus only , 2-wire leased lines). • A 4-pin modular jack for network management system (NMS) connection. • A 25-pin DB-25-S r ...

  • Paradyne 3800PLUS - page 18

    COMSPHERE 3800 Plus Modems 2-4 November 1996 3980-A2-GB30-20 495-14680 DB-25-P CONNECTOR FOR D ATA TERMINAL EQUIPMENT OPERA TION SUB-MINIA TURE 4-POSITION PLUG FOR NETWORK MANAGEMENT SYSTEM OPERA TION POWER SUPPL Y 6-POSITION PLUG FOR PERMISSIVE DIAL NETWORK OPERA TION OR 2-WIRE LEASED LINE OFF DIAL LEASED (3820 Plus ) DTE 1 NMS PWR ON Figure 2-3. ...

  • Paradyne 3800PLUS - page 19

    3810 Plus and 3820 Plus Installation 2-5 3980-A2-GB30-20 November 1996 3820 Plus 2-Wire Leased-Line Network Connection Obtain a JM8 to RJ1 1 (8-position to 6-position) crossover modular cable. See the equipment list in Appendix H for part number information, and Appendix E for a wiring diagram. Use the following procedure to connect a 3820 Plus mod ...

  • Paradyne 3800PLUS - page 20

    COMSPHERE 3800 Plus Modems 2-6 November 1996 3980-A2-GB30-20 Modem Power-Up Once your modem is properly connected to the DTE, dial and/or leased lines, and ac outlet, press the modem’ s rear panel power switch to the ON position. The modem begins a power-up self-test. This test takes several seconds to perform, and verifies the operation of most ...

  • Paradyne 3800PLUS - page 21

    3-1 3980-A2-GB30-20 November 1996 381 1 Plus Installation Overview 3-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3811 Plus Modem Package 3-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 22

    COMSPHERE 3800 Plus Modems 3-2 November 1996 3980-A2-GB30-20 — 50-pin to modular cable (JM8) for leased line applications • One 6-position to 6-position modular cord (required for network management applications). • A Shared Diagnostic Control Panel (SDCP). If the modem is to be managed by a network management system, an SDU must be supplied ...

  • Paradyne 3800PLUS - page 23

    381 1 Plus Installation 3-3 3980-A2-GB30-20 November 1996 The installation of a 381 1 Plus varies slightly if an SDCP is installed on the front of the carrier . T o install a 381 1 Plus modem into the carrier without an SDCP , perform the following steps: CAUTION If you remove the 381 1 Plus from the carrier , always use a ground strap when handlin ...

  • Paradyne 3800PLUS - page 24

    COMSPHERE 3800 Plus Modems 3-4 November 1996 3980-A2-GB30-20 If the modem is to communicate with an installed SDCP , install the modem as described above and perform the following steps: 1. Press the Select key on the SDCP . The cursor appears in the carrier selection entry . 2. Press the F1 ( " ) or F2 ( ↓ ) key until the carrier number you ...

  • Paradyne 3800PLUS - page 25

    4-1 3980-A2-GB30-20 November 1996 Front Panel Operation Overview 4-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diagnostic Control Panels 4-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 26

    COMSPHERE 3800 Plus Modems 4-2 November 1996 3980-A2-GB30-20 381 1 Plus Faceplate and Shared Diagnostic Control Panel (SDCP) The shared diagnostic control panel (SDCP) is used to manage carrier -mounted 381 1 Plus modems. Use the SDCP to issue commands to view and select configuration options on, or to monitor tests for , a specific 381 1 Plus mode ...

  • Paradyne 3800PLUS - page 27

    Front Panel Operation 4-3 3980-A2-GB30-20 November 1996 T able 4-1 3800 Plus DCP LEDs Label Color Indicates Pwr green ON – Power is on and the modem is capable of operating. Alrm red Flashing – A malfunction has been detected in either the modem or COMSPHERE 3000 Series Carrier . Diag (3810 Plus and 3820 Plus only) green The modem has responded ...

  • Paradyne 3800PLUS - page 28

    COMSPHERE 3800 Plus Modems 4-4 November 1996 3980-A2-GB30-20 The SDCP LEDs are listed and described in T able 4-2. T able 4-2 SDCP LEDs Label Color Indicates OK green Power is ON and the modem is capable of operating. Alarm red The modem has detected a problem with its operation. For example, the modem failed a self-test. BckUp yellow The modem, or ...

  • Paradyne 3800PLUS - page 29

    Front Panel Operation 4-5 3980-A2-GB30-20 November 1996 Left/Right Scroll Indicato r The left/right scroll indicator displays when more choices are available to the left and right of what is currently displayed on the LCD. Left Scroll Indicator < The left scroll indicator displays when more choices are available to the left of what is currently ...

  • Paradyne 3800PLUS - page 30

    COMSPHERE 3800 Plus Modems 4-6 November 1996 3980-A2-GB30-20 Menu Structure The menu tree is a hierarchical structure used to display functions that configure and control local and remote 3800 Plus modems. It is accessed via the DCP and is shown in Appendix A. The menu tree contains the following branches: Call Setup  Used to dial, disconnect, a ...

  • Paradyne 3800PLUS - page 31

    Front Panel Operation 4-7 3980-A2-GB30-20 November 1996 T op-Level Menu Status and Operational Messages Access to all menu tree branches from the DCP begins at the T op-Level menu, the head of the menu hierarchy . The LCD’ s top line identifies the modem status, as listed in T able 4-3, while the bottom line displays the main menu tree branches a ...

  • Paradyne 3800PLUS - page 32

    COMSPHERE 3800 Plus Modems 4-8 November 1996 3980-A2-GB30-20 T able 4-3 (2 of 3) T op Level Menu Status Normal Call Setup Messages Indicates Off Hook The modem is of f-hook and waiting to dial a telephone number . Dialing The remote modem is being dialed. T raining The modem is training or retraining. EC Negotiating The local and remote modems are ...

  • Paradyne 3800PLUS - page 33

    Front Panel Operation 4-9 3980-A2-GB30-20 November 1996 T able 4-3 (3 of 3) T op Level Menu Status Dial Backup Messages Indicates Dial Standby The modem is operating in Dial Standby mode. DialBckUp: MR* The modem is operating in a Dial Backup mode at the displayed data rate and is configured for Direct mode. Backup: MR* EC** The modem is operating ...

  • Paradyne 3800PLUS - page 34

    COMSPHERE 3800 Plus Modems 4-10 November 1996 3980-A2-GB30-20 T able 4-4 Common Operational Messages Common Operational Messages Indicates Please W ait... Appears when a command to a local device takes more than two seconds to complete. Command Sent... Appears when a command is sent to a remote modem. No Rem Response or Remote Modem Fail Appears wh ...

  • Paradyne 3800PLUS - page 35

    Front Panel Operation 4-1 1 3980-A2-GB30-20 November 1996 Selecting Factory Configuration Options After the modem passes the power -up self-test, configure it for operation using one of the factory preset configurations. The 3800 Plus modems have several factory preset templates that contain the most commonly used configuration options (straps) for ...

  • Paradyne 3800PLUS - page 36

    COMSPHERE 3800 Plus Modems 4-12 November 1996 3980-A2-GB30-20 • On initial power -up, the modem is in Command mode. T o verify that the modem is connected and functioning properly , enter the following: TYPE: AT PRESS: Return (Enter) The screen displays OK. If the modem does not return OK , refer to Appendix B, T roubleshooting . NOTE If you have ...

  • Paradyne 3800PLUS - page 37

    Front Panel Operation 4-13 3980-A2-GB30-20 November 1996 Diagnostic Control Panel Security Access NOTE This page of the manual is self-supporting and can be removed to prevent unwanted knowledge of the DCP security access selections. Use the DCP security access function to ‘ ‘lock” the DCP of any 3800 Plus modem and prevent unwanted user acce ...

  • Paradyne 3800PLUS - page 38

    5-1 3980-A2-GB30-20 November 1996 Call Setup Branch Overview 5-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Call Setup Branch 5-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 39

    COMSPHERE 3800 Plus Modems 5-2 November 1996 3980-A2-GB30-20 Call Setup Branch In the following descriptions, the shaded key indicates what key to press to perform the described operation. T o access the Call Setup branch from the T op-Level menu, select Call Setup: F1 Idle: 28.8 > Call_Setup F2 F3 Dial Dial allows you to dial any telephone numb ...

  • Paradyne 3800PLUS - page 40

    Call Setup Branch 5-3 3980-A2-GB30-20 November 1996 F1 Disconnect Command Complete F2 F3 The modem goes on-hook (hangs up) and the call is disconnected. This includes any calls being used for dial backup of leased lines. The Command Complete status message is displayed. T o exit this function and remain in the Call Setup branch, press the key . T o ...

  • Paradyne 3800PLUS - page 41

    COMSPHERE 3800 Plus Modems 5-4 November 1996 3980-A2-GB30-20 For example, under normal dial backup conditions, when a problem occurs on the leased line, the modems establish a connection over the dial network using a telephone number stored in directory location 1. F1 Call Setup: Dial Standby F2 F3 When this occurs, the Dial Standby function now ap ...

  • Paradyne 3800PLUS - page 42

    Call Setup Branch 5-5 3980-A2-GB30-20 November 1996 To access Change Directory from the Call Setup branch, make the following selections: F1 Call Setup: > Change_Directory F2 F3 Press the key until Change Directory is displayed. Press any function key to select Change Directory . F1 01 : 5551234 ← Nxt "# F2 F3 The phone number listed in d ...

  • Paradyne 3800PLUS - page 43

    COMSPHERE 3800 Plus Modems 5-6 November 1996 3980-A2-GB30-20 T able 5-1 V alid Dial Command Modifier Dial Command modifiers are parameters entered in the dial command string which specify how , when, and what number to dial. The following is a list of parameters the 3800 Plus modems recognize: T – T one (DTMF) dial. Any digit 0–9, *, #, A, B, C ...

  • Paradyne 3800PLUS - page 44

    6-1 3980-A2-GB30-20 November 1996 Status Branch Overview 6-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status Branch 6-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 45

    COMSPHERE 3800 Plus Modems 6-2 November 1996 3980-A2-GB30-20 VF VF displays the condition of the dial or leased-line connection. T o access VF from the Status branch, make the following selection: F1 Status: VF Identity F2 F3 Select VF . F1 Status : VF > SigQual = Excelent F2 F3 The modem’ s signal quality is displayed on the LCD’ s bottom l ...

  • Paradyne 3800PLUS - page 46

    Status Branch 6-3 3980-A2-GB30-20 November 1996 Identity Identity displays the modem’ s serial number , model number , firmware revision level, hardware part number and firmware part number . Retrieval of this information is useful if you are purchasing additional or replacement modems and/or making firmware upgrades. T o access Identity from the ...

  • Paradyne 3800PLUS - page 47

    COMSPHERE 3800 Plus Modems 6-4 November 1996 3980-A2-GB30-20 DTE DTE displays the state and/or activity of the EIA-232-D interface leads: LSD, DTR, DSR, T st, TXD, RXD, R TS, and CTS signals are monitored. The interface leads status is updated every 5 seconds. T o access DTE from the Status branch, make the following selections: F1 Status: Identity ...

  • Paradyne 3800PLUS - page 48

    Status Branch 6-5 3980-A2-GB30-20 November 1996 To access Record from the Status branch, make the following selections: F1 Status < Options Record F2 F3 Press the key until Record appears. Select Record. F1 Record Status Display Clear F2 F3 To display sequence faults, select Display . F1 Record Number 1 Modem O.K. F2 F3 The LCD displays the firs ...

  • Paradyne 3800PLUS - page 49

    7-1 3980-A2-GB30-20 November 1996 T est Branch Overview 7-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T est Branch 7-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 50

    COMSPHERE 3800 Plus Modems 7-2 November 1996 3980-A2-GB30-20 T est Branch To access the T est branch from the T op-Level menu, make the following selections: F1 Idle : 28.8 Status T est F2 F3 Press the key until T est appears. Select T est. Abort Abort ends any test that is in progress and brings the modem back to the normal mode of operation. Conf ...

  • Paradyne 3800PLUS - page 51

    T est Branch 7-3 3980-A2-GB30-20 November 1996 Loc Analog Loop Loc Analog Loop performs a local analog loopback (CCITT V .54 Loop 3), Figure 7-1, that verifies modem operation as well as the connection between the DTE and modem. The modem must be of fline and in synchronous or asynchronous Direct mode to perform this test, otherwise Invalid Command ...

  • Paradyne 3800PLUS - page 52

    COMSPHERE 3800 Plus Modems 7-4 November 1996 3980-A2-GB30-20 Rem Digital Loop Rem Digital Loop performs a remote digital loopback (CCITT V .54 Loop 2), Figure 7-2. This test can verify the integrity of the local modem, the communications link, and the remote modem. Any data or pattern entered at the local DTE is sent to and returned from the remote ...

  • Paradyne 3800PLUS - page 53

    T est Branch 7-5 3980-A2-GB30-20 November 1996 Loc Digital Loop Loc Digital Loop is issued by a local modem and forces it to loopback any data received from the remote modem (Figure 7-3). (This test operates the same as a CCITT V .54 Loop 2 except it is issued at your modem.) This is useful if a remote modem is incapable of initiating a remote digi ...

  • Paradyne 3800PLUS - page 54

    COMSPHERE 3800 Plus Modems 7-6 November 1996 3980-A2-GB30-20 Pattern Pattern can transmit and receive a 51 1 bit error rate test pattern. It can also be used with a local analog loopback or a remote digital loopback to simulate data passing through the modem. For this test to operate properly , the modems must be online and in Synchronous or Asynch ...

  • Paradyne 3800PLUS - page 55

    T est Branch 7-7 3980-A2-GB30-20 November 1996 T o access Pattern from the T est branch, make the following selections: F1 T est : > Pattern F2 F3 Press the key until Pattern appears. Select Pattern to start this test. F1 T est : Pattern > Blks Errd = xxxxxxx F2 F3 BlksErrd=xxxxxxx displays the number of blocks of data found in error (block s ...

  • Paradyne 3800PLUS - page 56

    8-1 3980-A2-GB30-20 November 1996 Configure Branch Overview 8-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configure Branch 8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 57

    COMSPHERE 3800 Plus Modems 8-2 November 1996 3980-A2-GB30-20 Figures 8-1 and 8-2 graphically display the interaction between the edit area and configuration areas as viewed from the perspective of the DCP and the A T command set. CONTENTS OF Active (Saved) ARE AUTOMA TICALL Y COPIED TO Active (Operating) WHEN A SA VE IS COMMANDED VIA THE DCP , ON A ...

  • Paradyne 3800PLUS - page 58

    Configure Branch 8-3 3980-A2-GB30-20 November 1996 Active (Saved) (A TZ0, A TZ3) LOAD Active (Operating) USING AT Z OR A T&F COMMAND Active (Operating) CHANGES MADE USING ANY AT COMMAND IMMEDIA TEL Y AFFECT MODEM OPERA TION USE A T&W COMMAND TO SA VE CHANGES TO Active (Saved), Customer 1, OR Customer 2 494-13080-0 2 Customer 1 (A TZ1) Custo ...

  • Paradyne 3800PLUS - page 59

    COMSPHERE 3800 Plus Modems 8-4 November 1996 3980-A2-GB30-20 Configure Branch The Configure branch of the T op-Level menu contains all of the modem’ s configuration options (straps) which determine how the modem operates. These configuration options are accessed by scrolling down and across various levels of the Configure branch. The Configure br ...

  • Paradyne 3800PLUS - page 60

    Configure Branch 8-5 3980-A2-GB30-20 November 1996 Editing and Saving a Configuration Option The following example shows how to change the Remote Access Password using the DCP . (If you ever intend to access another 3800 Plus Series modem via the Remote branch of the T op-Level menu, the Remote Access Password must be the same for both modems.) By ...

  • Paradyne 3800PLUS - page 61

    COMSPHERE 3800 Plus Modems 8-6 November 1996 3980-A2-GB30-20 F1 RemAccssPasswrd Nxt ąĄ ° 0 0000000 F2 F3 Press the key to move the cursor to the next position. F1 RemAccssPasswrd Nxt ąĄ ° 12345678 F2 F3 Continue this sequence until you have entered the new password value. T o save the new password to a configuration area, make the following s ...

  • Paradyne 3800PLUS - page 62

    Configure Branch 8-7 3980-A2-GB30-20 November 1996 Configuration T ables The modem’ s configuration options are arranged into eight groups based upon functionality: DTE Interface (T able 8-1), DTE Dialer (T able 8-2), Line Dialer (T able 8-3), Dial Line (T able 8-4), Leased Line (T able 8-5), V .42/MNP/Buf fer (T able 8-6), T ests (T able 8-7), a ...

  • Paradyne 3800PLUS - page 63

    COMSPHERE 3800 Plus Modems 8-8 November 1996 3980-A2-GB30-20 T able 8-1 (2 of 7) DTE Interface Configuration Options *Async #Data Bits: 8 Nxt 8 7 9(DirectMde) 6(DirectMde) Asynchronous Number of Data Bits. Determines if the asynchronous data length is composed of 6, 7, 8, or 9 data bits. This data length excludes start, parity , and stop bits. 8 ? ...

  • Paradyne 3800PLUS - page 64

    Configure Branch 8-9 3980-A2-GB30-20 November 1996 T able 8-1 (3 of 7) DTE Interface Configuration Options DTR Action: Ignore Nxt Stndrd_RS232 Ignore CntrlsOnHook Off=ReloadStrp Off=CmdMode Data T erminal Ready Action. DTR is a signal from the DTE to the modem indicating that the DTE is connected and ready for operation. Standard RS232 – Allows t ...

  • Paradyne 3800PLUS - page 65

    COMSPHERE 3800 Plus Modems 8-10 November 1996 3980-A2-GB30-20 T able 8-1 (4 of 7) DTE Interface Configuration Options DSR Control: Forced_On Nxt Forced_On Stndrd_RS232 WinkWhenDisc Follows_DTR On_Early Delay_T oData DialBkT oggle Data Data Set Ready Control. DSR is a signal from the modem to the DTE indicating the modem is connected and ready for o ...

  • Paradyne 3800PLUS - page 66

    Configure Branch 8-1 1 3980-A2-GB30-20 November 1996 T able 8-1 (5 of 7) DTE Interface Configuration Options RTS Action: Ignore Nxt Ignore Stndrd_RS232 Sim_Cntl_Car Cntl_Car Request-to-Send Action. RTS is a signal from the DTE to the modem indicating the DTE has data to send to the modem. Ignore – Modem assumes RTS is always ON. Use this selectio ...

  • Paradyne 3800PLUS - page 67

    COMSPHERE 3800 Plus Modems 8-12 November 1996 3980-A2-GB30-20 T able 8-1 (6 of 7) DTE Interface Configuration Options RTS/CTS Delay: 0 msec Nxt 0msec 10msec 50msec 150msec 600msec Request-to-Send/Clear-to-Send Delay . RTS/CTS Delay sets the delay time between the modem receiving R TS from the DTE and the modem sending CTS to the DTE. This delay is ...

  • Paradyne 3800PLUS - page 68

    Configure Branch 8-13 3980-A2-GB30-20 November 1996 T able 8-1 (7 of 7) DTE Interface Configuration Options TX Clock Source: Internal Nxt Internal External RXC_Loop T ransmit Clock Source. Determines the source of timing for synchronous data transmitted from the DTE. Internal – The transmit data’ s clock source is derived from the modem’s int ...

  • Paradyne 3800PLUS - page 69

    COMSPHERE 3800 Plus Modems 8-14 November 1996 3980-A2-GB30-20 DTE Dialer The DTE Dialer configuration options establish the DTE-to-modem protocol for call establishment and control. T able 8-2 shows each DTE Dialer configuration option as it appears on the LCD, with the Async Dial factory default setting (the default value if the modem is just bein ...

  • Paradyne 3800PLUS - page 70

    Configure Branch 8-15 3980-A2-GB30-20 November 1996 T able 8-2 (2 of 5) DTE Dialer Configuration Options *A T Escape Char: 043 ASCI Nxt " 043 ASCI A T Escape Character . The escape sequence (+++) allows you to move back and forth between Command mode and Data mode. The ASCII value of the escape character (43 ASCII) can be set to any ASCII valu ...

  • Paradyne 3800PLUS - page 71

    COMSPHERE 3800 Plus Modems 8-16 November 1996 3980-A2-GB30-20 T able 8-2 (3 of 5) DTE Dialer Configuration Options *Backspace Char: 008 ASCI Nxt ↑ 008 ASCI Backspace Character . Sets the character used to perform a backspace in Command mode. The factory default is 08 (ASCII backspace character). A T command equivalent is S-register S5= n . *Linef ...

  • Paradyne 3800PLUS - page 72

    Configure Branch 8-17 3980-A2-GB30-20 November 1996 T able 8-2 (4 of 5) DTE Dialer Configuration Options *ResultCode Form: Words Nxt Words Numbers (1) Numbers (2) Result Codes Format. Controls whether or not result codes appear as words or as numeric codes. Some DTEs do not recognize Result Codes as words; therefore, numbers are required. The Numbe ...

  • Paradyne 3800PLUS - page 73

    COMSPHERE 3800 Plus Modems 8-18 November 1996 3980-A2-GB30-20 T able 8-2 (5 of 5) DTE Dialer Configuration Options V25bis IdleFill: Mark Nxt Mark Flag V .25bis Idle Fill. Determines whether a mark or flag is used as an idle fill character for the DTE. The modem responds to the DTE using the same idle fill. NOTE: This configuration option only appea ...

  • Paradyne 3800PLUS - page 74

    Configure Branch 8-19 3980-A2-GB30-20 November 1996 Line Dialer The Line Dialer configuration options establish parameters used by the modem to answer or originate calls. T able 8-3 shows each Line Dialer configuration option as it appears on the LCD, with the Async Dial factory default setting (the default value if the modem is just being installe ...

  • Paradyne 3800PLUS - page 75

    COMSPHERE 3800 Plus Modems 8-20 November 1996 3980-A2-GB30-20 T able 8-3 (2 of 4) Line Dialer Configuration Options BusyT one Detect: Enable Nxt Enable Disable Busy T one Detect. Sets the modem to monitor for Busy T one (Enable) or ignore Busy T one (Disable). This configuration option is normally enabled; however , if the modem receives false busy ...

  • Paradyne 3800PLUS - page 76

    Configure Branch 8-21 3980-A2-GB30-20 November 1996 T able 8-3 (3 of 4) Line Dialer Configuration Options Long Space Disc: Enable Nxt Enable Disable Long Space Disconnect. Determines the modem’ s response to a continuous spacing condition sent from the remote modem when it goes on-hook. Issuing a long space is one method of disconnecting a call. ...

  • Paradyne 3800PLUS - page 77

    COMSPHERE 3800 Plus Modems 8-22 November 1996 3980-A2-GB30-20 T able 8-3 (4 of 4) Line Dialer Configuration Options MakeBusyViaDTR: Disable Nxt Disable Enable Make Busy Via DTR. Determines if the modem goes of f-hook when DTR is Off. Enable this setting if the DTE normally keeps DTR ON and turns DTR Off when the DTE cannot accept a call. NOTE: This ...

  • Paradyne 3800PLUS - page 78

    Configure Branch 8-23 3980-A2-GB30-20 November 1996 Dial Line The Dial Line configuration options are used to configure the modem for operation over dial lines. T able 8-4 shows each Dial Line configuration option as it appears on the LCD, with the Async Dial factory default setting (the default value if the modem is just being installed) shown fol ...

  • Paradyne 3800PLUS - page 79

    COMSPHERE 3800 Plus Modems 8-24 November 1996 3980-A2-GB30-20 T able 8-4 (2 of 4) Dial Line Configuration Options Automode: Enable Nxt Enable Disable System 85 Automode. Allows the modem to automatically detect the remote modem’ s modulation. Enable – The modem automatically adapts to the modulation scheme and line rate of the remote modem, and ...

  • Paradyne 3800PLUS - page 80

    Configure Branch 8-25 3980-A2-GB30-20 November 1996 T able 8-4 (3 of 4) Dial Line Configuration Options Dial TX Level: Permissv(– 9) Nxt Permissv(– 9) –10 dBm –1 1 dBm –12 dBm –13 dBm –14 dBm –15 dBm –16 dBm –17 dBm –18 dBm –19 dBm –20 dBm –21 dBm –22 dBm –23 dBm –24 dBm –25 dBm –26 dBm –27 dBm –28 dBm –2 ...

  • Paradyne 3800PLUS - page 81

    COMSPHERE 3800 Plus Modems 8-26 November 1996 3980-A2-GB30-20 T able 8-4 (4 of 4) Dial Line Configuration Options Asymmetric Rate: Enable Nxt Enable Disable Asymmetric Rate. Controls rate symmetry when running V .34 modulation. (This configuration option does not appear unless V .34 modulation is selected.) Enable – The modem operates in asymmetr ...

  • Paradyne 3800PLUS - page 82

    Configure Branch 8-27 3980-A2-GB30-20 November 1996 Leased Line The Leased Line configuration options are used to configure the modem for operation over leased lines. NOTE The Leased Line configuration group only appears if the modem is configured with the Sync Leased factory preset template. The Leased Line configuration group only appears if the ...

  • Paradyne 3800PLUS - page 83

    COMSPHERE 3800 Plus Modems 8-28 November 1996 3980-A2-GB30-20 T able 8-5 (2 of 4) Leased Line Configuration Options *LeasedLine Rate: 28800(V34) Nxt 28800(V34) 33600 31200 26400(V34) 24000(V34) 21600(V34) 19200(V34) 16800(V34) 14400(V34) 12000(V34) 9600(V34) 7200(V34) 4800(V34) 2400(V34) - OR - Nxt 19200(V32t) 16800(V32t) 14400(V32b) 12000(V32b) 96 ...

  • Paradyne 3800PLUS - page 84

    Configure Branch 8-29 3980-A2-GB30-20 November 1996 T able 8-5 (3 of 4) Leased Line Configuration Options *Leased TX Level: 0 N x t0– 1– 2– 3– 4– 5– 6– 7– 8– 9– 1 0– 1 1– 1 2– 13 –1 4 – 15 Leased T ransmit Level. Selects the modem’ s transmit power level over leased lines. The transmit output level can be selected in ...

  • Paradyne 3800PLUS - page 85

    COMSPHERE 3800 Plus Modems 8-30 November 1996 3980-A2-GB30-20 T able 8-5 (4 of 4) Leased Line Configuration Options *Auto Redial Nxt Dir_1 Dirs_1-2 Dirs_1-3 Dirs_1-4 Dirs_1-5 Dirs_1-6 Dirs_1-7 Dirs_1-8 Dirs_1-9 Dirs_1-10 Auto Redial. W orks in conjunction with the Bad Lines Auto Originate and Rate Auto Originate options. It allows repeated automati ...

  • Paradyne 3800PLUS - page 86

    Configure Branch 8-31 3980-A2-GB30-20 November 1996 V .42/MNP/Buffer V .42/MNP/Buf fer configuration options determine the type of error correction and flow control used by the modems and attached DTEs. Some choices within this group may not appear depending upon how previous configuration options have been selected. If the Async/Sync Mode configur ...

  • Paradyne 3800PLUS - page 87

    COMSPHERE 3800 Plus Modems 8-32 November 1996 3980-A2-GB30-20 T able 8-6 (2 of 6) V .42/MNP/Buffer Configuration Options *V42bis Compress: Enable Nxt Enable Disable V .42bis Compression. Enables or disables V .42bis data compression. Enable – Data compression operates in both the transmit and receive directions. This is the recommended setting fo ...

  • Paradyne 3800PLUS - page 88

    Configure Branch 8-33 3980-A2-GB30-20 November 1996 T able 8-6 (3 of 6) V .42/MNP/Buffer Configuration Options *EC Fallbck Char: 013 ASCI Nxt " 013 ASCI Error Control Fallback Character . This configuration option allows you to enter the ASCII value of the error control fallback character . This provides the remote modem with the ability to en ...

  • Paradyne 3800PLUS - page 89

    COMSPHERE 3800 Plus Modems 8-34 November 1996 3980-A2-GB30-20 T able 8-6 (4 of 6) V .42/MNP/Buffer Configuration Options *XON/XOFF Psthru: Disable Nxt Disable Enable XON/XOFF Passthrough. Considers an XON/XOFF character as data and passes it on to the remote modem. In this case, the DTE at one end of the communications link can send flow control ch ...

  • Paradyne 3800PLUS - page 90

    Configure Branch 8-35 3980-A2-GB30-20 November 1996 T able 8-6 (5 of 6) V .42/MNP/Buffer Configuration Options *Send Break Cntl: Data-First Nxt Data-First Break-First Send Break Control. Determines what is sent from the modem first, data or break if a break sequence is sent from the DTE. Data First (Nonexpedited) – A break is treated as a data ch ...

  • Paradyne 3800PLUS - page 91

    COMSPHERE 3800 Plus Modems 8-36 November 1996 3980-A2-GB30-20 T able 8-6 (6 of 6) V .42/MNP/Buffer Configuration Options *CellularEnhance: Disable End Disable Enable Enables or disables V .42 Cellular Enhancement mode. Disable – The modem uses standard techniques for V .42 operation. Enable – Cellular enhancements are enabled. The modem is stil ...

  • Paradyne 3800PLUS - page 92

    Configure Branch 8-37 3980-A2-GB30-20 November 1996 T est The T est configuration options determine specifics, such as the duration of a test, for the various diagnostic tests available to the modem. T able 8-7 shows each T est configuration option as it appears on the LCD, with the Async Dial factory default setting (the default value if the modem ...

  • Paradyne 3800PLUS - page 93

    COMSPHERE 3800 Plus Modems 8-38 November 1996 3980-A2-GB30-20 T able 8-7 (2 of 2) T est Configuration Options V54 Address: Disable Nxt Disable (Address V alues) V .54 Address. Determines which remote 3800 Plus modem is placed into a remote loopback test. This can be either a remote digital loopback or local analog loopback. This type of addressing ...

  • Paradyne 3800PLUS - page 94

    Configure Branch 8-39 3980-A2-GB30-20 November 1996 Misc The Miscellaneous configuration options determine specifics for various functions, including network management parameters and remote modem access. T able 8-8 shows each Misc (Miscellaneous) configuration option as it appears on the LCD, with the Async Dial factory default setting (the defaul ...

  • Paradyne 3800PLUS - page 95

    COMSPHERE 3800 Plus Modems 8-40 November 1996 3980-A2-GB30-20 T able 8-8 (2 of 3) Miscellaneous Configuration Options Speaker V olume: Medium Nxt Medium Low High Speaker V olume. Controls the level of speaker volume. The factory default is Medium. NOTE: Speaker V olume can also be temporarily set using the Control branch; however , a reset or power ...

  • Paradyne 3800PLUS - page 96

    Configure Branch 8-41 3980-A2-GB30-20 November 1996 T able 8-8 (3 of 3) Miscellaneous Configuration Options NMS_Call_Msgs: CallCnct&Prg Nxt CallCnct&Prg Disable CallCnctOnly CallProgOnly NMS Call Messages. Determines if modem status and/or call summary information is sent to the 6700 Series NMS. The modem can itemize status, such as CallPro ...

  • Paradyne 3800PLUS - page 97

    COMSPHERE 3800 Plus Modems 8-42 November 1996 3980-A2-GB30-20 Security Configuration Options The Security Configuration Options group allows you to view and set dial access security parameters. This group appears only if the dial access security feature has been installed. T able 8-9 shows each Security configuration option as it appears on the LCD ...

  • Paradyne 3800PLUS - page 98

    Configure Branch 8-43 3980-A2-GB30-20 November 1996 T able 8-9 (2 of 2) Security Configuration Options *DTE_PW_BkSpChar: 008 Nxt " 008 DTE Password Backspace Character . Sets the character that is used to perform a backspace in security mode. This character can be set to any ASCII value from 0 to 127. The factory default is 08 (ASCII backspace ...

  • Paradyne 3800PLUS - page 99

    9-1 3980-A2-GB30-20 November 1996 Control Branch Overview 9-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control Branch 9-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 100

    COMSPHERE 3800 Plus Modems 9-2 November 1996 3980-A2-GB30-20 Speaker Speaker allows you to make temporary adjustments to the modem’ s speaker volume. Upon a reset, speaker volume returns to its configured setting. For more information on speaker settings, refer to the Misc section in Chapter 7. T o access Speaker from the Control branch, make the ...

  • Paradyne 3800PLUS - page 101

    Control Branch 9-3 3980-A2-GB30-20 November 1996 Make Busy/Remove Make Busy The Make Busy function forces the modem of f-hook so it cannot answer a call. This is often used with PBX systems to permit the busy out of a PBX port for rotary or hunt groups. W ARNING T o not violate FCC and DOC regulations, this function must only be used behind a user ...

  • Paradyne 3800PLUS - page 102

    COMSPHERE 3800 Plus Modems 9-4 November 1996 3980-A2-GB30-20 Download Code The Download Code function sets parameters within the modem when transferring firmware to a remote modem or when receiving firmware upgrades from a locally attached PC-based controller . The latter should only be performed by customer service personnel. There are two selecti ...

  • Paradyne 3800PLUS - page 103

    Control Branch 9-5 3980-A2-GB30-20 November 1996 W ARNING Pressing any function key now begins the transfer to the remote modem. This process takes the communications link out of service for several minutes depending upon the data rate of the link (28,800 bps = 5 minutes; 14,400 bps = 10 minutes; 9600 bps = 15 minutes; 4800 bps = 30 minutes). If th ...

  • Paradyne 3800PLUS - page 104

    COMSPHERE 3800 Plus Modems 9-6 November 1996 3980-A2-GB30-20 As data banks are transferred, the local and remote LCD’ s bottom line displays the status of the download process, and the number of records sent versus the total number of records for that bank. F1 RemClone OK Call_Setup F2 F3 If the download is successful, the local modem displays Re ...

  • Paradyne 3800PLUS - page 105

    10-1 3980-A2-GB30-20 November 1996 Remote Branch Overview 10-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Branch 10-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 106

    COMSPHERE 3800 Plus Modems 10-2 November 1996 3980-A2-GB30-20 Remote DCP access is accomplished using either the primary or secondary channel (if available) of the VF line. Using the primary channel gives a much faster response time due to the higher data rate, but it also interrupts data flow because primary data is stopped when Remote mode is act ...

  • Paradyne 3800PLUS - page 107

    Remote Branch 10-3 3980-A2-GB30-20 November 1996 The T op-Level menu of the remote 3800 Plus modem is similar to the local 3800 Plus modem with the following exceptions: • Change Directory is the only function available under the Call Setup branch. • Self and Local Analog Loop do not appear under the T est branch when using the secondary channe ...

  • Paradyne 3800PLUS - page 108

    1 1-1 3980-A2-GB30-20 November 1996 Security Overview 1 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Originate Access Security 1 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 109

    COMSPHERE 3800 Plus Modems 1 1-2 November 1996 3980-A2-GB30-20 Originate Access Security Originate Access lets you control who can originate a call from a local modem via the A T command set. This is useful in LAN and modem pooling applications. W ith Originate Access security , a local user ’ s password is embedded in the A T dial command. If th ...

  • Paradyne 3800PLUS - page 110

    Security 1 1-3 3980-A2-GB30-20 November 1996 NOTE While pulse dial can be used to originate the call, DTMF tones must be used for the password. This can be accomplished by using the P and T modifiers appropriately . Refer to the Dial command in Chapter 13, AT Command Set and S-Registers , for more on modifiers. This method of password entry require ...

  • Paradyne 3800PLUS - page 111

    COMSPHERE 3800 Plus Modems 1 1-4 November 1996 3980-A2-GB30-20 Security Branch The Security branch of the T op-Level menu allows you to change and save parameters that are critical to the dial access security password database. This database is a collection of passwords and their associated parameters that determine how the modems control password ...

  • Paradyne 3800PLUS - page 112

    Security 1 1-5 3980-A2-GB30-20 November 1996 T o enter your Administrative Password from Set_Access_Ctrl, make the following selections: F1 Security > Set_Access_Ctrl F2 F3 Select Set_Access_Ctrl from the Security branch. F1 Admin Password? Ent ą Ą " 00000000 F2 F3 The Administrative Password appears. This occurs every time you enter the ...

  • Paradyne 3800PLUS - page 113

    COMSPHERE 3800 Plus Modems 1 1-6 November 1996 3980-A2-GB30-20 F1 Select Index Ent ą Ą " 0 001 F2 F3 Select Index appears. Press the F2 ( " ) key to increment index values. Press the key to move the cursor to the next position. Continue this sequence until the desired index appears, and then press Ent. If an index outside of the range i ...

  • Paradyne 3800PLUS - page 114

    Security 1 1-7 3980-A2-GB30-20 November 1996 T able 1 1-1 Edit Password T able Group Options PsWdT ype xxxx Nxt Cleared DTE Entry VF_Entry VF_plus_DTE Password T ype. Indicates whether this index location is configured for VF-side password, DTE-side password, or both. Cleared displays for an index location that contains no valid entry . Note that t ...

  • Paradyne 3800PLUS - page 115

    COMSPHERE 3800 Plus Modems 1 1-8 November 1996 3980-A2-GB30-20 Set Answer Sec Set Answer Security determines if dial access security is enabled or disabled. This method of inbound security is configured in the answering modem. Although this also appears under the Security Configuration Option group, it can only be changed from the Set Answer Sec LC ...

  • Paradyne 3800PLUS - page 116

    Security 1 1-9 3980-A2-GB30-20 November 1996 Set Orig Sec Set Originate Security controls whether or not the modem can originate a call using A T commands when the dial access security feature is installed. This method of outbound security only applies to modems originating a call. T o access Set_Orig_Sec from Set Access Ctrl, make the following se ...

  • Paradyne 3800PLUS - page 117

    COMSPHERE 3800 Plus Modems 1 1-10 November 1996 3980-A2-GB30-20 Set Admin PsWd Set Administrative Password is used to change the Administrative Password value. The Administrative Password is an 8-digit decimal number that allows authorized users to enter the Access Security Control function. NOTE If this value is forgotten, then the only way to acc ...

  • Paradyne 3800PLUS - page 118

    Security 1 1-1 1 3980-A2-GB30-20 November 1996 F1 Reset Security < Erase_All_PassWd F2 F3 To reset security , press until Erase_All_PassWd appears on the LCD. Select Erase_All_PassWd. The entire security database is erased and the Administrative Password defaults to the Reset Default password value. This value appears as a single number on the l ...

  • Paradyne 3800PLUS - page 119

    COMSPHERE 3800 Plus Modems 1 1-12 November 1996 3980-A2-GB30-20 Some experimentation may be necessary to determine the number of pauses necessary for your call. A DTE-side password is entered after the modems have trained, but before a normal connection is established. The following example illustrates how to enter a DTE-side password: TYPE: abc123 ...

  • Paradyne 3800PLUS - page 120

    Security 1 1-13 3980-A2-GB30-20 November 1996 T able 1 1-5 is an example of a database table with passwords configured for DTE Entry only . This type of password is entered via the originating user ’ s DTE. T able 1 1-5 Security Database T able Using DTE-Side Password DTE Password Only Index Password T ype Assigned to 1001 winter DTE_Entry User A ...

  • Paradyne 3800PLUS - page 121

    COMSPHERE 3800 Plus Modems 1 1-14 November 1996 3980-A2-GB30-20 T able 1 1-7 is an example of a security database table that uses paired VF and DTE passwords for use in VF_w/_DTE answer security mode. T able 1 1-7 Security Database T able Using Paired VF-Side and DTE-Side Passwords VF and DTE Passwords Index Password T ype Assigned to 02 user1 DTE_ ...

  • Paradyne 3800PLUS - page 122

    12-1 3980-A2-GB30-20 November 1996 Fax Operation Overview 12-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fax Operation 12-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 123

    COMSPHERE 3800 Plus Modems 12-2 November 1996 3980-A2-GB30-20 There are no Diagnostic Control Panel (DCP) functions unique to fax operation. If your fax software requires that you change the configuration of your modem, see the appropriate sections of Chapter 8, Configur e Branch . The DCP is disabled during fax operation. Y our fax software uses A ...

  • Paradyne 3800PLUS - page 124

    13-1 3980-A2-GB30-20 November 1996 A T Command Set and S-Registers Overview 13-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Modes 13-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 125

    COMSPHERE 3800 Plus Modems 13-2 November 1996 3980-A2-GB30-20 Use the O command to return to Data mode from online Command mode. Enter the following command: TYPE: AT O PRESS: Enter Command Guidelines Review the following guidelines before using any A T Commands. • The escape sequence (+++) is used to enter online Command mode from Data mode. • ...

  • Paradyne 3800PLUS - page 126

    A T Command Set and S-Registers 13-3 3980-A2-GB30-20 November 1996 T able 13-1 (1 of 1 1) 3800 Plus A T Commands A T Command Description Front Panel Branch A/ Repeat Last Command Re-executes last command string. (Not to be preceded with A T or followed by pressing the Return key .) A Answer Mode Goes off-hook and attempts to establish a connection ...

  • Paradyne 3800PLUS - page 127

    COMSPHERE 3800 Plus Modems 13-4 November 1996 3980-A2-GB30-20 T able 13-1 (2 of 1 1) 3800 Plus A T Commands A T Command Front Panel Branch Description D n (Cont’d) , – Pause. Causes the modem to pause before processing the next character in the dial string. The length of this pause is determined by the setting of the Pause T ime configuration o ...

  • Paradyne 3800PLUS - page 128

    A T Command Set and S-Registers 13-5 3980-A2-GB30-20 November 1996 T able 13-1 (3 of 1 1) 3800 Plus A T Commands A T Command Front Panel Branch Description L n Speaker V olume L0 Selects low volume. L1 Selects low volume. L2 Selects medium volume L3 Selects high volume. ControlSpeaker ConfigureEditMisc M n Speaker On/Off M0 Speaker always off. M ...

  • Paradyne 3800PLUS - page 129

    COMSPHERE 3800 Plus Modems 13-6 November 1996 3980-A2-GB30-20 T able 13-1 (4 of 1 1) 3800 Plus A T Commands A T Command Front Panel Branch Description X n Extended Result Code, Dial T one Detect, and Busy T one Detect Configuration Options Dial Busy Extended T one T one Result Code Detect Detect X0 Disable Disable Disable X1 Enable Disable Disable ...

  • Paradyne 3800PLUS - page 130

    A T Command Set and S-Registers 13-7 3980-A2-GB30-20 November 1996 T able 13-1 (5 of 1 1) 3800 Plus A T Commands A T Command Front Panel Branch Description &C n LSD Control &C0 Forced On. LSD on at all times. &C1 Standard RS232. LSD is on when the remote modem’ s carrier signal is detected. LSD is of f when carrier signal is not detec ...

  • Paradyne 3800PLUS - page 131

    COMSPHERE 3800 Plus Modems 13-8 November 1996 3980-A2-GB30-20 T able 13-1 (6 of 1 1) 3800 Plus A T Commands A T Command Front Panel Branch Description &F n Select Factory Default Configuration Options Loads factory configuration options into Active (Operating) area. &F0 Async Dial &F1 Sync Dial &F2 Sync Leased: Answer &F3 UNIX D ...

  • Paradyne 3800PLUS - page 132

    A T Command Set and S-Registers 13-9 3980-A2-GB30-20 November 1996 T able 13-1 (7 of 1 1) 3800 Plus A T Commands A T Command Front Panel Branch Description & I Dial T ransmit Level When Dial T ransmit Level T ype is set to Permissive, & I n sets Dial T ransmit Level to a value between –10 and –32 dBm. & I 99 and & I 100 cause th ...

  • Paradyne 3800PLUS - page 133

    COMSPHERE 3800 Plus Modems 13-10 November 1996 3980-A2-GB30-20 T able 13-1 (8 of 1 1) 3800 Plus A T Commands A T Command Front Panel Branch Description &M n and &Q n Async/Sync Mode and DTE Dialer T ype &M0, &Q0 Modem operates in Asynchronous mode and uses A T Command protocol. &M1, &Q1 Modem operates in Synchronous mode and ...

  • Paradyne 3800PLUS - page 134

    A T Command Set and S-Registers 13-1 1 3980-A2-GB30-20 November 1996 T able 13-1 (9 of 1 1) 3800 Plus A T Commands A T Command Front Panel Branch Description &T n T ests &T0 Abort. Stops any test in progress. &T1 Local Analog Loop. &T2 Pattern. T ransmits and receives a 51 1 Bit Error Rate T est (BERT). &T3 Local Digital Loopbac ...

  • Paradyne 3800PLUS - page 135

    COMSPHERE 3800 Plus Modems 13-12 November 1996 3980-A2-GB30-20 T able 13-1 (10 of 1 1) 3800 Plus A T Commands A T Command Front Panel Branch Description A n Error Control Maximum Frame Size A0 64 A1 128 A2 192 A3 256 A4 32 A5 16 ConfigureEdit V42/MNP/Buffer C n Error Control Negotiate Buffer C0 Disable. C1 Enable. C2 Disables and switc ...

  • Paradyne 3800PLUS - page 136

    A T Command Set and S-Registers 13-13 3980-A2-GB30-20 November 1996 T able 13-1 (1 1 of 1 1) 3800 Plus A T Commands A T Command Front Panel Branch Description Q n Flow Control of DTE, Flow Control of Modem Flow Flow Control Control of of DTE Modem Q0 Disable Disable Q1 XON/XOFF XON/XOFF Q2 CTS to DTE Disable Q3 CTS to DTE R TS to Mdm Q4 XON/X ...

  • Paradyne 3800PLUS - page 137

    COMSPHERE 3800 Plus Modems 13-14 November 1996 3980-A2-GB30-20 S-Register List S-registers affect the operating parameters of 3800 Plus modems. S-registers are only applicable when the DTE Dialer T ype configuration option is set for A T . (See &M n command.) T able 13-2 lists all S-registers supported by 3800 Plus modems. The first column list ...

  • Paradyne 3800PLUS - page 138

    A T Command Set and S-Registers 13-15 3980-A2-GB30-20 November 1996 T able 13-2 (2 of 13) 3800 Plus S-Registers A T Command Front Panel Branch Description S4 Line Feed Character Register determines ASCII value used as the line feed character . Enter a value from 0–127 for the line feed character . Factory setting is 10 (ASCII carriage return or l ...

  • Paradyne 3800PLUS - page 139

    COMSPHERE 3800 Plus Modems 13-16 November 1996 3980-A2-GB30-20 T able 13-2 (3 of 13) 3800 Plus S-Registers A T Command Front Panel Branch Description S14 Asymmetric Rate Mode Register determines whether VF rates for transmitting and receiving are identical when using V .34 modulation. Enabling the function permits the two rates to be dif ferent. Re ...

  • Paradyne 3800PLUS - page 140

    A T Command Set and S-Registers 13-17 3980-A2-GB30-20 November 1996 T able 13-2 (4 of 13) 3800 Plus S-Registers A T Command Front Panel Branch Description S37 Auto Redial Auto Redial allows repeated automatic dial backup attempts by specifying the range of Directory Locations that can be tried. A redial attempt is made in response to a bad phone nu ...

  • Paradyne 3800PLUS - page 141

    COMSPHERE 3800 Plus Modems 13-18 November 1996 3980-A2-GB30-20 T able 13-2 (5 of 13) 3800 Plus S-Registers A T Command Front Panel Branch Description S41 Dial-Line Rate Register determines the modem’ s data rate and modulation scheme for operation on dial lines. Register has the following values: 1=14,400 (V .32bis) 2=12,000 (V .32bis) 3=9600 (V ...

  • Paradyne 3800PLUS - page 142

    A T Command Set and S-Registers 13-19 3980-A2-GB30-20 November 1996 T able 13-2 (6 of 13) 3800 Plus S-Registers A T Command Front Panel Branch Description S44 Leased-Line Rate Register determines the modem’ s data rate and modulation scheme for operation on either 2-wire or 4-wire leased lines in either Answer or Originate mode. Register has the ...

  • Paradyne 3800PLUS - page 143

    COMSPHERE 3800 Plus Modems 13-20 November 1996 3980-A2-GB30-20 T able 13-2 (7 of 13) 3800 Plus S-Registers A T Command Front Panel Branch Description S47 Auto Dial Standby Register determines if the modem performs an automatic dial standby if in Dial Backup mode. Register has the following values: 0=Disable 1=15 minutes 2=1 hour 3=4 hours 255=T est ...

  • Paradyne 3800PLUS - page 144

    A T Command Set and S-Registers 13-21 3980-A2-GB30-20 November 1996 T able 13-2 (8 of 13) 3800 Plus S-Registers A T Command Front Panel Branch Description S53 V .54 Address Identifies the address of the modem to be placed in a loopback test. Register has the following values: 0 =Disable 1–34 =Modem address Factory setting is Disable. ConfigureEd ...

  • Paradyne 3800PLUS - page 145

    COMSPHERE 3800 Plus Modems 13-22 November 1996 3980-A2-GB30-20 T able 13-2 (9 of 13) 3800 Plus S-Registers A T Command Front Panel Branch Description S62 V .25bis Coding Register identifies to the modem the type of coding used by the DTE while in V .25bis mode. Register has the following values: 0=ASCII 1=EBCDIC Factory setting is ASCII. Configure ...

  • Paradyne 3800PLUS - page 146

    A T Command Set and S-Registers 13-23 3980-A2-GB30-20 November 1996 T able 13-2 (10 of 13) 3800 Plus S-Registers A T Command Front Panel Branch Description S74 Network Position Identification Register identifies each modem as either a control or tributary modem. Register has the following values: 0=T ributary 1=Control Factory setting is T ributary ...

  • Paradyne 3800PLUS - page 147

    COMSPHERE 3800 Plus Modems 13-24 November 1996 3980-A2-GB30-20 T able 13-2 (1 1 of 13) 3800 Plus S-Registers A T Command Front Panel Branch Description S80 No Data Disconnect T rigger Signal Register determines whether Pin 2 (transmit data) or Pin 3 (receive data) of the modem’ s RS-232 serial interface is monitored so that the modem can disconne ...

  • Paradyne 3800PLUS - page 148

    A T Command Set and S-Registers 13-25 3980-A2-GB30-20 November 1996 T able 13-2 (12 of 13) 3800 Plus S-Registers A T Command Front Panel Branch Description S88 Straps When Disconnected Register determines whether the Active(Operating) area is reloaded upon a disconnect. Register has the following values: 0 (or 231)=No Change 1 (or 232)=Reload 2 (or ...

  • Paradyne 3800PLUS - page 149

    COMSPHERE 3800 Plus Modems 13-26 November 1996 3980-A2-GB30-20 T able 13-2 (13 of 13) 3800 Plus S-Registers A T Command Front Panel Branch Description S92 V .29 T rain On Data Register determines whether the modem must receive a standard V .29 training sequence in order to enter data mode (Disable) or whether it should use the received data mode fo ...

  • Paradyne 3800PLUS - page 150

    A-1 3980-A2-GB30-20 November 1996 Menu T ree Overview The following pages hold graphic representations of the general menu structure of the front panel or SDCP displays. The model, installed features, and configuration options all may af fect what is actually displayed at each level of the menus. A ...

  • Paradyne 3800PLUS - page 151

    COMSPHERE 3800 Plus Modems A-2 November 1996 3980-A2-GB30-20 ...

  • Paradyne 3800PLUS - page 152

    Menu T ree A-3 3980-A2-GB30-20 November 1996 ...

  • Paradyne 3800PLUS - page 153

    COMSPHERE 3800 Plus Modems A-4 November 1996 3980-A2-GB30-20 ...

  • Paradyne 3800PLUS - page 154

    B-1 3980-A2-GB30-20 November 1996 Result Codes Overview T able B-1 lists all the result codes 3800 Plus modems may send to the DTE. Result codes can be numeric or verbal, terse or extended. See the Q n , V n , and X n commands in Chapter 13 for more information. T able B-1 (1 of 3) Result Codes Numbers (1) Numbers (2) Word Description 0 0 OK Comman ...

  • Paradyne 3800PLUS - page 155

    COMSPHERE 3800 Plus Modems B-2 November 1996 3980-A2-GB30-20 T able B-1 (2 of 3) Result Codes Numbers (1) Description Word Numbers (2) 17 17 CONNECT 16800* Connection at 16,800 bps 19 1 CONNECT 300* Connection at 300 bps 20 10 CONNECT 2400/ EC*** Connection at 2400 bps with error control 21 11 CONNECT 4800/ EC*** Connection at 4800 bps with error c ...

  • Paradyne 3800PLUS - page 156

    Result Codes B-3 3980-A2-GB30-20 November 1996 T able B-1 (3 of 3) Result Codes Numbers (1) Description Word Numbers (2) 43 43 CONNECT 21600/ EC*** Connection at 21,600 bps with error control 44 44 CONNECT 24000/ EC*** Connection at 24,000 bps with error control 45 45 CONNECT 26400/ EC*** Connection at 26,400 bps with error control 46 46 CONNECT 28 ...

  • Paradyne 3800PLUS - page 157

    C-1 3980-A2-GB30-20 November 1996 T roubleshooting Overview C-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview Appendix B points out basic problems that can occur when operating a 3800 Plus modem. Use T ables C-1 through C-6 to check out th ...

  • Paradyne 3800PLUS - page 158

    COMSPHERE 3800 Plus Modems C-2 November 1996 3980-A2-GB30-20 T able C-2 Modem – DTE Connection Symptom Action Modem does not accept or echo back A T commands V erify that the cable between the Async port of the DTE and the modem is a standard RS-232 cable. If the cable is bad, replace it. (Null modem cables, also known as crossover cables, do not ...

  • Paradyne 3800PLUS - page 159

    T roubleshooting C-3 3980-A2-GB30-20 November 1996 T able C-3 (2 of 2) Modem – VF Connection Symptom Action Modem goes of f-hook, answers, but does not connect Perform a Local Analog Loopback test and verify that data entered at the DTE is echoed back to the DTE. V erify that the originating modem is compatible. V erify that originating modem rec ...

  • Paradyne 3800PLUS - page 160

    COMSPHERE 3800 Plus Modems C-4 November 1996 3980-A2-GB30-20 T able C-4 Online Operation Symptom Action Data scrambled V erify that the character format (data bits, parity , and stop bits) is set to the same value in both modems. Missing data during a transfer V erify that you are using the same method of flow control for both the modem and the DTE ...

  • Paradyne 3800PLUS - page 161

    D-1 3980-A2-GB30-20 November 1996 T echnical Specifications T able D-1 shows the technical specifications for 3800 Plus modems. T able D-1 (1 of 3) T echnical Specifications for COMSPHERE 3800 Plus Modems Specifications Criteria APPROV ALS (1 10 V ac, 60 Hz only) FCC Part 15 Class A FCC Part 68 Registration Number: (See label on modem.) UL 3810 Plu ...

  • Paradyne 3800PLUS - page 162

    COMSPHERE 3800 Plus Modems D-2 November 1996 3980-A2-GB30-20 T able D-1 (2 of 3) T echnical Specifications for COMSPHERE 3800 Plus Modems Specifications Criteria COMP A TIBILITY DIAL-LINE MODULA TIONS Proprietary V .34 (33,600, 31,200 bps) ITU-T V .34 (28,800, 26,400, 24,000, 21,600, 19,200, 16,800, 14,400,12,000, 9600, 7200, 4800, 2400 bps) V .32 ...

  • Paradyne 3800PLUS - page 163

    T echnical Specifications D-3 3980-A2-GB30-20 November 1996 T able D-1 (3 of 3) T echnical Specifications for COMSPHERE 3800 Plus Modems Specifications Criteria AC POWER REQUIREMENTS 3810 Plus and 3820 Plus 1 10 V ac, 50 to 60 Hz POWER CONSUMPTION 3810 Plus and 3820 Plus 8 watts (typical, including power supply , speaker off) 381 1 Plus 6 watts (ty ...

  • Paradyne 3800PLUS - page 164

    E-1 3980-A2-GB30-20 November 1996 Pin Assignments EIA-232-D Pin Assignments E-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VF Connector Pin Assignments E-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . JM8 to RJ ...

  • Paradyne 3800PLUS - page 165

    COMSPHERE 3800 Plus Modems E-2 November 1996 3980-A2-GB30-20 EIA-232-D Pin Assignments T able E-1 lists the EIA-232-D pin assignments for the modem. T able E-1 EIA-232-D Pin Assignments RS-232 Pin Name EIA Circuit CCITT Signal Source Circuit Function 1 — AA 101 — Shield 2 TXD BA 103 DTE T ransmit Data 3 RXD BB 104 DCE Receive Data 4 RTS CA 105 ...

  • Paradyne 3800PLUS - page 166

    Pin Assignments E-3 3980-A2-GB30-20 November 1996 VF Connector Pin Assignments T able E-2 lists the connector pin assignments for 3810 Plus and 3820 Plus modular jacks and the pin assignments for the TELCO jacks (Figure E-1). T able E-2 VF Connector Pin Assignments Pin 3810 Plus Leased Dial/ 3820 Plus T ype of T elco Jack Pin 3810 Plus Leased 3820 ...

  • Paradyne 3800PLUS - page 167

    COMSPHERE 3800 Plus Modems E-4 November 1996 3980-A2-GB30-20 JM8 to RJ1 1 Crossover Cable For 2-wire leased-line connections to a JM8 network interface, an 8-position to 6-position crossover cable (see Figure E-2) must be used according to the following FCC requirements: ‘ ‘The RJ series of jacks should not be used for connecting data equipment ...

  • Paradyne 3800PLUS - page 168

    F-1 3980-A2-GB30-20 November 1996 CCITT V .25bis Dialing Commands and Responses Overview F-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Call Request Commands F-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Paradyne 3800PLUS - page 169

    COMSPHERE 3800 Plus Modems F-2 November 1996 3980-A2-GB30-20 Call Request Commands Call Request commands are issued from the DTE to the modem and are responsible for initiating any dial calls. Call Request commands include Call Request with Number Provided (CRN) and Call Request with Stored Memory Address Provided (CRS). Call Request with Number Pr ...

  • Paradyne 3800PLUS - page 170

    CCITT V .25bis Dialing Commands and Responses F-3 3980-A2-GB30-20 November 1996 Call Answer Commands Call Answer commands disable or enable the modem’ s AutoAnswer function. These commands are issued from the DTE. Call Answer commands include Incoming Call (INC), Disregard Incoming Call (DIC) and Connect Incoming Call (CIC). Incoming Call (INC) T ...

  • Paradyne 3800PLUS - page 171

    COMSPHERE 3800 Plus Modems F-4 November 1996 3980-A2-GB30-20 Command Response A Command Response indicates that the command entered was a valid or invalid entry . Command Response includes V alid (V AL) and Invalid (INV). V alid (V AL) The V AL response indicates that the modem has accepted the V .25bis command issued by the DTE. V AL is similar to ...

  • Paradyne 3800PLUS - page 172

    CCITT V .25bis Dialing Commands and Responses F-5 3980-A2-GB30-20 November 1996 T able F-2 lists V .25bis response messages supported by 3800 Plus modems. T able F-2 V .25bis Response Messages V .25bis Command Description A T Command/ S-Register Equivalent CALL RESPONSE CFI Call Failure Indication BUSY , NO ANSWER, NO CARRIER, NO DIAL TONE, ERROR C ...

  • Paradyne 3800PLUS - page 173

    G-1 3980-A2-GB30-20 November 1996 Default Configuration Options Overview G-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview T able G-1 lists all default configuration options for the main four factory preset configurations. (Additional conf ...

  • Paradyne 3800PLUS - page 174

    COMSPHERE 3800 Plus Modems G-2 November 1996 3980-A2-GB30-20 T able G-1 (2 of 4) Factory Default Configuration Options Configuration Option Sync Leased Answer/ Originate Mode Default Settings Sync Dial Default Settings Async Dial and UNIX Dial Default Settings DTE DIALER DTE Dialer T ype A T Escape Character Escape Guard T ime Break Forces Escape C ...

  • Paradyne 3800PLUS - page 175

    Default Configuration Options G-3 3980-A2-GB30-20 November 1996 T able G-1 (3 of 4) Factory Default Configuration Options Configuration Option Sync Leased Answer/ Originate Mode Default Settings Sync Dial Default Settings Async Dial and UNIX Dial Default Settings DIAL LINE Modulation Dial Line Rate Automode Autorate Dial T ransmit Level V .22bis Gu ...

  • Paradyne 3800PLUS - page 176

    COMSPHERE 3800 Plus Modems G-4 November 1996 3980-A2-GB30-20 T able G-1 (4 of 4) Factory Default Configuration Options Configuration Option Sync Leased Answer/ Originate Mode Default Settings Sync Dial Default Settings Async Dial and UNIX Dial Default Settings TESTS DTE RL (CT140) DTE LL (CT141) T est Timeout Receive Remote Loopback V .54 Address V ...

  • Paradyne 3800PLUS - page 177

    H-1 3980-A2-GB30-20 November 1996 Equipment List Equipment Feature/Part Number Model 3810 Plus (1 10 v) 3980-A2-201 Model 381 1 Plus 3981-B1-001 Model 3820 Plus (1 10 v) 3982-A2-201 V .29 Feature 3980-C1-002 V .33 Feature 3980-C1-003 Expanded Security Feature (for 381 1 Plus modems only) 3980-C1-004 User ’s Guide 3980-M1-001 6-position, 4-wire mo ...

  • Paradyne 3800PLUS - page 178

    Glossary-1 3980-A2-GB30-20 November 1996 Glossary Active (Operating) A configuration area containing configuration options currently in use by the modem. When a power cycle occurs, a reset is performed, or a save is issued using the DCP , this area is updated with the contents of Active (Saved). Active (Saved) A nonvolatile configuration area conta ...

  • Paradyne 3800PLUS - page 179

    COMSPHERE 3800 Plus Modems Glossary-2 November 1996 3980-A2-GB30-20 automatic dial backup When leased-line operation fails, this function forces the modem to dial the telephone number stored in directory location 1; communication over the dial network continues with the remote modem. For a 3800 Plus modem to perform this properly , the telephone nu ...

  • Paradyne 3800PLUS - page 180

    Glossary Glossary-3 3980-A2-GB30-20 November 1996 character A letter , figure, number , punctuation, or other symbols. character echo A way to check the accuracy of data transmission by sending (displaying) all the characters being transmitted to the monitor . circuit pack lock A screw lock tab installed over a circuit card’ s latch release tab t ...

  • Paradyne 3800PLUS - page 181

    COMSPHERE 3800 Plus Modems Glossary-4 November 1996 3980-A2-GB30-20 DB-25 connector A 25-pin connector that is used to connect a cable which enables communications between two devices. dBm A decibel referenced to one milliwatt. This unit measures relative signal power . DCE The equipment (Data Communications Equipment or Data Circuit T erminating E ...

  • Paradyne 3800PLUS - page 182

    Glossary Glossary-5 3980-A2-GB30-20 November 1996 error contr ol An algorithm used to correct data transmission errors. escape sequence Default setting is +++. This sequence lets you switch your modem from Data mode to Command mode. extended r esult codes An asynchronous message (in either numbers or words) that includes VF data rate and error cont ...

  • Paradyne 3800PLUS - page 183

    COMSPHERE 3800 Plus Modems Glossary-6 November 1996 3980-A2-GB30-20 LCD Liquid Crystal Display . A thin sandwich of two sealed glass plates containing liquid crystal material. When voltage is applied, the amount of light able to pass through the glass plates is altered so that messages may be ‘ ‘written” on the display . leased line A private ...

  • Paradyne 3800PLUS - page 184

    Glossary Glossary-7 3980-A2-GB30-20 November 1996 Originate mode The modem is in a state where it is ready to transmit a call. In a dial network, it is the modem that makes the call. In a leased-line network, it is one of two sides of the network that is selected to be the originating modem. parity A way of checking data accuracy by counting the nu ...

  • Paradyne 3800PLUS - page 185

    COMSPHERE 3800 Plus Modems Glossary-8 November 1996 3980-A2-GB30-20 SDCP Shared Diagnostic Control Panel. An optional user interface similar to the front panel of a 3810 Plus modem that attaches to the front of a COMSPHERE 3000 Series Carrier . Installed at eye level into one COMSPHERE 3000 Series Carrier , it controls and monitors modems in all th ...

  • Paradyne 3800PLUS - page 186

    Glossary Glossary-9 3980-A2-GB30-20 November 1996 V .22 A standard for modems operating full-duplex with asynchronous or synchronous data at 1200 bps over the dial network (PSTN). V .22bis A standard for modems operating full-duplex with asynchronous or synchronous data at 1200 or 2400 bps over the dial network (PSTN). V .27bis A communications sta ...

  • Paradyne 3800PLUS - page 187

    Index-1 3980-A2-GB30-20 November 1996 Index A A/ (Repeat Last Command), 13-3 Abort (T est branch), 7-2 ac power connection, 2-5 requirements, D-3 Access from Remote, 8-40 Active (Operating) configuration area, 8-1 Active (Saved) configuration area, 8-1 Administrative Password, 1 1-4, 1 1-10 Answer, 5-3 Answer Access security , 1 1-2 Answer Access S ...

  • Paradyne 3800PLUS - page 188

    COMSPHERE 3800 Plus Modems Index-2 November 1996 3980-A2-GB30-20 B Backspace Character, 8-16 Bad Lines Auto Originate, 8-29 Blind Dial Pause, 8-19 Break Buffer Control, 8-34 Break Forces Escape, 8-15 Busy T one Detect, 8-20 C cables auxiliary , E-4 crossover, E-4 Call Answer commands (V .25bis), F-3 Call Request commands (V .25bis), F-2 Call Setup ...

  • Paradyne 3800PLUS - page 189

    Index Index-3 3980-A2-GB30-20 November 1996 DSR Control (&S), 8-10, 13-10 DTE connection, 2-3 DTE Dialer T ype, 8-14 DTE Interface, 8-7, D-3 DTE LL (CT141), 13-20 DTE Local Loopback, 8-37 DTE Rate, 8-7 DTE Rate=VF Rate, 8-13 DTE rates supported, D-2 DTE Remote Loopback, 8-37 DTE RL (CT140), 13-20 DTE status, 6-4 DTE-side password backspace char ...

  • Paradyne 3800PLUS - page 190

    COMSPHERE 3800 Plus Modems Index-4 November 1996 3980-A2-GB30-20 M Make Busy , 9-3 Make Busy V ia DTR, 8-22, 13-22 Maximum Frame Size, 8-35 menu tree, A-1 overview , 4-6 remote, 10-3 messages, 4-7 MI/MIC Dialing, 8-22 MNP5 Compression, 8-32 models, 1-2 carrier-mounted, 3-1 standalone, 2-1 Modem-to-Modem Flow Control, 8-34 Modulation (Dial Line conf ...

  • Paradyne 3800PLUS - page 191

    Index Index-5 3980-A2-GB30-20 November 1996 S18 (T est T imeout), 8-37, 13-16 S26 (R TS/CTS Delay), 8-12, 13-16 S36 (Rate Auto Originate), 8-29, 13-16 S37 (Auto Redial), 8-22, 8-30, 13-17 S38 (DTR Continuous Repeat), 8-18, 13-17 S39 (Receive Buffer Disconnect Delay), 8-35, 13-17 S40 (Auto Make Busy), 8-21, 13-17 S41 (Dial Line Rate), 13-18 S43 (T r ...

  • Paradyne 3800PLUS - page 192

    COMSPHERE 3800 Plus Modems Index-6 November 1996 3980-A2-GB30-20 V V .22bis Guard T one, 8-25 V .25bis Coding, 8-17, 13-22 V .25bis commands, F-4 V .25bis dialing commands and responses, F-1 V .25bis Idle Character , 13-22 V .25bis Idle Fill, 8-18 V .25bis New Line Character , 8-18, 13-22 V .25bis response messages, F-5 V .29 T rain On Data, 13-26 ...

Manufacturer Paradyne Category Modem

Documents that we receive from a manufacturer of a Paradyne 3800PLUS can be divided into several groups. They are, among others:
- Paradyne technical drawings
- 3800PLUS manuals
- Paradyne product data sheets
- information booklets
- or energy labels Paradyne 3800PLUS
All of them are important, but the most important information from the point of view of use of the device are in the user manual Paradyne 3800PLUS.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Paradyne 3800PLUS, service manual, brief instructions and user manuals Paradyne 3800PLUS. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Paradyne 3800PLUS.

Similar manuals

A complete manual for the device Paradyne 3800PLUS, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Paradyne 3800PLUS by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Paradyne 3800PLUS.

A complete Paradyne manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Paradyne 3800PLUS - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Paradyne 3800PLUS, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Paradyne 3800PLUS, that we can find in the current document
3. Tips how to use the basic functions of the device Paradyne 3800PLUS - which should help us in our first steps of using Paradyne 3800PLUS
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Paradyne 3800PLUS
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Paradyne 3800PLUS in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Paradyne 3800PLUS?

Use the form below

If you did not solve your problem by using a manual Paradyne 3800PLUS, ask a question using the form below. If a user had a similar problem with Paradyne 3800PLUS it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)