-
Samsung SCC-3000 - page 1
Thank you for buying a Samsung SYSTEM CONTROLLER. This manual will guide you through using the SYSTEM CONTROLLER. Please read this manual carefully before using the SYSTEM CONTROLLER. ...
-
Samsung SCC-3000 - page 2
《 2 》 Contents ● Important Safety Instructions 3 ● Major Functions and Features (1) Overview 5 (2) Features 5 ● Product Components 5 ● System Overview 6 ● Names and Functions of Each Part (1) Camera Setup Section 7 (2) Number Pad 8 (3) External Device Selectors 8 (4) Universal Controller 9 (5) DVR Controller 9 (6) Camera Controller 11 ...
-
Samsung SCC-3000 - page 3
《 3 》 Important Safety Instructions ■ All work related to the installation of this appliance must be performed by qualified service personnel or system installers. - If the product is connected or installed improperly, electric shock, fire, severe injury, and/or damage can result. ■ Please install the product on a completely flat floor. - A ...
-
Samsung SCC-3000 - page 4
《 4 》 Important Safety Instructions ■ If the controller body gets dirty, turn the power off and wipe the surface with a soft cloth. - Do not use chemical agents such as alcohol or benzene. ■ For detailed information on upgrading the firmware, please direct your inquiries to the installation vendor. Maintenance and Repair This equipment has ...
-
Samsung SCC-3000 - page 5
《 5 》 Major Functions and Features (1) Overview This product is designed for use only with the Speed Dome camera, CCTV receiver, and Samsung Digital Video Recorder. ● Speed Dome camera : Samsung Techwin (SPD-1600/2200/2500), PELCO-D, PANASONIC (WV-CS854A), SAMSUNG ELECTRONICS (SCC-643-641) ● CCTV Receiver : SRX-100B ● DVR : Samsung Techwi ...
-
Samsung SCC-3000 - page 6
《 6 》 System Overview ※ Please refer to page 39 for the detailed connection map of the JUNCTION Box, Controllers and external devices. (1) General Connection : Controller Connection Cable : RS-485/422 : Video Cable DVR Dome Camera + DVR: 255 max. Dome Camera Dome Camera Dome Camera SVR-1630: 255 max. CCD Camera Remarks Junction Box ...
-
Samsung SCC-3000 - page 7
《 7 》 Names and Functions of Each Part (1) Camera Setup Section ① RESET : Resets camera power. ② PRESET : Moves camera to the preset location (see p.16). ③ LIGHT : Toggles the lights around the camera on and off. ④ AUX : Toggles the camera’s external case AUX on and off. ⑤ TOUR : Sets more than 1 group for tour and performs continuo ...
-
Samsung SCC-3000 - page 8
《 8 》 Names and Functions of Each Part (2) Number Pad ※ 'F' in the table below refers to the Function button. ① 0 ~ 9 : Used for entering camera ID, channel number, monitor number, DVR ID, etc. (see p.23). ② F + 0 : Activates the system setup menu (see p.24). ③▲ / ▼ : Used for increasing or decreasing menu values in detail ...
-
Samsung SCC-3000 - page 9
《 9 》 Names and Functions of Each Part (4) Universal Controller ① ZOOM W/T : Performs camera zoom action (wide and telephoto). ② FOCUS -/+ : Used for manual focus adjustment. ③ || : Used for moving the menu cursor up (when menu is active), pausing DVR playback, or playing stills. ④■ : Used for moving the menu cursor down (when menu is ...
-
Samsung SCC-3000 - page 10
《 10 》 Names and Functions of Each Part ※ Some DVR controller buttons may not be supported or may be used differently than as described in this manual, depending on the DVR model. Please refer to the table below for the buttons supported by major DVR model manufacturers. The DVR button with multiple functions works in the same way on the cont ...
-
Samsung SCC-3000 - page 11
《 11 》 Names and Functions of Each Part (6) Camera Controller ① Joystick: Used for moving the camera up, down, left, and right, and for zoom control (see p.13). 1) Tilt up (Up button): Moves the camera up. 2) Tilt down (Down button): Moves the camera down. 3) Tilt left (Left button): Moves the camera left. 4) Tilt right (Right button): Moves ...
-
Samsung SCC-3000 - page 12
《 12 》 Before Operation (1) Power-On ① Power on the connected external devices before turning the controller on. ② Press the power button at the back of the controller to power on the controller. ③ The [SYSTEM Controller] message and F/W version will be displayed in the LCD monitor, and the message will disappear when the controller is re ...
-
Samsung SCC-3000 - page 13
《 13 》 Before Operation (4) Joystick/Camera Control Button ■ The joystick can be used to control the camera ’ s left and right (pan) and up and down (tilt) movements. ■ The joystick can be used to control camera zoom functions. [Camera wide zoom] [Camera telephoto zoom] ...
-
Samsung SCC-3000 - page 14
《 14 》 Before Operation (5) Camera Movement Speed Control ■ Use the joystick or press the Slow/Fast button at the bottom of the camera control button section to adjust the camera movement speed. ▤ You must press the ESC button after adjusting the camera movement speed in order to be able to use other controller buttons. ▤ The SLOW/FAST bu ...
-
Samsung SCC-3000 - page 15
《 15 》 ● The menu may be different depending on the PTZ camera model. ● Press the ESC button to move to an upper setup mode. INFORMA TION PTZ Mode (1) PTZ Setup Mode ■ This menu is for setting up the PTZ camera function. It is impossible to operate Speed Dome and DVR by sub-controllers when the master controller is set to on. ① At the i ...
-
Samsung SCC-3000 - page 16
《 16 》 PTZ Mode (2) PRESET ■ This menu is for setting the camera to move to preset locations. (2-1) PRESET Setup ① At the [PTZ SETUP 1 ▶ ] menu, press the 1 button (see p.15). ② Use the joystick or camera control button (SCC-3000 model) to move the camera to the desired location (move up, down, left, and right, and control zoom). ③ En ...
-
Samsung SCC-3000 - page 17
《 17 》 PTZ Mode (3) SWING ■ This menu is for setting the camera to alternate between two assigned locations horizontally (pan) or vertically (tilt). Setting the SWING SETUP menu by controllers is only possible in the SPD series. In case of products by other manufacturers, the setting has to be done by the OSD menu of the camera. See the camer ...
-
Samsung SCC-3000 - page 18
《 18 》 PTZ Mode (4) GROUP ■ This menu is for setting repeated sequential surveillance of assigned locations with assigned speed and intervals. Setting the GROUP SETUP menu by controllers is only available for an SPD series. In case of products by other manufacturers, the setting has to be done by the OSD menu of the camera. See the camera man ...
-
Samsung SCC-3000 - page 19
《 19 》 PTZ Mode (5) TOUR ■ This menu is for setting one or more Groups for Tour so that continuous Group operations can be carried out. The TOUR SETUP menu is only available for an SPD series. (5-1) TOUR Setup ① At the [PTZ SETUP 1 ▶ ] menu, press the 4 button (see p.15). ② Press a Group number to add to the Tour. ▤ Up to 6 Groups can ...
-
Samsung SCC-3000 - page 20
《 20 》 PTZ Mode GROUP 1 T OUR GROUP 3 ...
-
Samsung SCC-3000 - page 21
《 21 》 PTZ Mode (6) MODEL ■ This menu is for setting the PTZ camera ID and camera type. ① At the [PTZ SETUP 1 ▶ ] menu, press the ▶▶ button (see p.15). ② Press the 1 button to move to the Model Setup screen. PTZSETUP2 1:MODEL 2:TRACE 3:AF PressNumericKey +, - :ModelChange PTZMODELSETUP PTZ ID: 0? ...
-
Samsung SCC-3000 - page 22
《 22 》 PTZ Mode (7) TRACE ■ This menu is for inputting camera movements, through joystick or camera control buttons, into the memory for a certain period of time, to allow repeating of stored movements when performing the Trace (PATTERN) function. Setting the TRACE SETUP menu by controller is only available for an SPD series. In case of produ ...
-
Samsung SCC-3000 - page 23
《 23 》 PTZ Mode (8) AF (Auto-Focus) ■ This menu is for adjusting camera focus manually or automatically after camera operation. If AF is set to OFF in the camera setup menu, set the AF of the controller to ON and then automatic adjustment is performed after camera operation. ① At the [PTZ SETUP 1 ▶ ] menu, press the ▶▶ button (see p.1 ...
-
Samsung SCC-3000 - page 24
《 24 》 PTZ Mode (9) OSD ■ This is used for displaying the camera menu on the monitor. ① At the initial screen, press the OSD button. ② Use the controller buttons to set up the camera menu. - OSD : SPD 1600/2200/2500 - Toggle camera menu on/off (hold down for 2 seconds) PELCO-D - Toggle camera menu on/off (press ESC) PANASONIC (WV-CS854A) ...
-
Samsung SCC-3000 - page 25
《 25 》 DVR Mode DVR MODEL Setup ■ This menu is for setting the DVR ID and model for operation by a controller. Sub-controllers cannot be used if the master controller is in Setup mode. ① At the initial screen, press the FUNCTION button and press the 0 button to activate the [SETUP SYSTEM] menu. ② Press the 2 button to activate the [DVR SE ...
-
Samsung SCC-3000 - page 26
《 26 》 Controller Mode (1) Controller Setup Mode ■ Sub-controllers cannot be operated if the master controller is in setup mode. ① At the initial screen, press the FUNCTION button and press the 0 button to activate the [SETUP SYSTEM] menu. ② Press the 3 button to activate the [Controller SETUP 1 ▶ ] menu. ③ Press the ▶▶ button to ...
-
Samsung SCC-3000 - page 27
《 27 》 Controller Mode (2) Controller ID Setup ■ This menu is for setting controller ID. ① At the [Controller SETUP 1 ▶ ] menu, press the 1 button (see p.26). ② Press a number on the number pad to enter a controller ID. ③ Press the ENTER button to set the controller ID. ▤ Assign number 1 for setting the controller ID for the master ...
-
Samsung SCC-3000 - page 28
《 28 》 Controller Mode (4) DATA COPY ■ This menu is for copying master controller menu data to a sub-controller. The controller ID value is not copied. ① At the [Controller SETUP 1 ▶ ] menu, press the 3 button (see p.26). ② Press a number on the number pad to enter the ID number for the sub- controller where the data will be copied. ③ ...
-
Samsung SCC-3000 - page 29
《 29 》 Controller Mode (5) RESPONSE ■ If the camera RESPONSE is set to two-way reception (RESPONSE ON), the controller RESPONSE menu must be set to ON. If the camera RESPONSE is set to one-way reception (RESPONSE OFF), the controller RESPONSE menu must be set to OFF.If this is not followed, the system may have a configuration conflict.For mor ...
-
Samsung SCC-3000 - page 30
《 30 》 Controller Mode ▤ For information on camera RESPONSE settings (DIP switch settings), refer to the camera manual. (5-1) SPD-1600 DIP Setup ON OFF DIP-SW 1 Not used DIP-SW 2 Reserved DIP-SW 3 RESPONSE Setup DIP-SW 4 Factory default Always OFF Always OFF HALF DUPLEX FULL DUPLEX HALF DUPLEX FULL DUPLEX Always OFF (5-3) SPD-2500 DIP Setup O ...
-
Samsung SCC-3000 - page 31
《 31 》 Controller Mode (6) PASSWORD ■ This menu is for setting the password to enter when changing controller setup values upon power-on. (6-1) PASSWORD Setup ① At the [Controller SETUP 1 ▶ ] menu, press the ▶▶ button (see p.26). ② Press the 2 button to activate the Password Setup screen. ③ Press the 1 button to activate the Passw ...
-
Samsung SCC-3000 - page 32
《 32 》 Controller Mode (6-2) Applying Password – Setup Mode ① At the Password Setup screen, press the 2 button. ② Press the 1 button to ask for a password every time the setup mode is selected. Press the 2 button to skip asking for a password. PASSWORDSETUP 1:PASSWORDSETUP 2:MENUON 3:POWERON PressNumericKey PASSWORDSE ...
-
Samsung SCC-3000 - page 33
《 33 》 Controller Mode (7) PRIORITY ■ This menu is for setting the connected sub-controller to use a PTZ camera or DVR within the specified restrictions. This menu is available for master controller (ID: 1) only. ① At the [Controller SETUP 1 ▶ ] menu, press the ▶▶ button twice (see p.26). ② Press the 1 button to activate the Priorit ...
-
Samsung SCC-3000 - page 34
《 34 》 Controller Mode (8) DEFAULT ■ This menu is for resetting the changed controller setup values to the default values. ① At the [Controller SETUP 1 ▶ ] menu, press the ▶▶ button twice (see p.26). ② Press the 2 button to open the Default Setup screen. ③ Press the 1 button to change the controller setup values to the default val ...
-
Samsung SCC-3000 - page 35
《 35 》 REFERENCE (1) Swing, Group Movement Speed ▤ For Swing setup, the speed setup value can be 240 ˚ /second for pan, and 180 ˚ /second for tilt. Setup value Degrees / second Setup value Degrees / second Setup value Degrees / second Setup value Degrees / second 1 0.8 33 23 1 0.8 33 23 2 1.0 34 24 2 1.0 34 24 3 1.5 35 25 3 1.5 35 25 4 2.0 ...
-
Samsung SCC-3000 - page 36
《 36 》 REFERENCE X X X X X X X X X X X X X X X X X X X X X X X X X X X X X RX+ RX- X X RX+ RX- X X RX+ RX- GRD TX+ TX- RX+ RX- TX+ TX- RX+ RX- TX+ TX- RX+ RX- TX+ TX- RX+ RX- TX+ TX- RX+ RX- TX+ TX- RX+ RX- TX+ TX- (2) System Connections (2-1) Connecting Controller and Junction Box (2-2) Connecting Junction Box and External Devices JUNCTION BOX ...
-
Samsung SCC-3000 - page 37
《 37 》 REFERENCE (3) RS-485/422 Pin Layout (D_SUB_FEMALE) Terminal Name 1 +12V 2 RX+ (RS-485+) PORT1 3 RX- (RS-485-) PORT1 4 TX- PORT1 5 TX+ PORT1 6 - 7 RX+ (RS-485 +) PORT2 8 RX- (RS-485 -) PORT2 9 TX- PORT2 10 TX+ PORT2 11 GND 12 RX+ (RS-485 +) PORT3 13 RX- (RS-485 -) PORT3 14 TX- PORT3 15 TX+ PORT3 (4) RS-232C Pin Layout (D_SUB_MALE) Termina ...
-
Samsung SCC-3000 - page 38
《 38 》 REFERENCE (5) Controller Specifications MODEL SCC-3000 Power (Consumption) 12VDC(Max 700mA) Control DVR & Speed Dome (SPD-2500, 1600, 2200) PTZ Control SPD-2500, 1600, 2200 all function control - DVR : SVR-1620 / 900 / 430 / 1630 / 1650 - PTZ : SEC, PELCO-D, PANASONIC Remote Control RS-485 / RS-422 Connector 3Port Baud Rate (bps) Max ...
-
Samsung SCC-3000 - page 39
P/No.:6806-0586-01A SALES NETWORK SAMSUNG TECHWIN CO., LTD. 145-3, Sangdaewon 1-Dong, Jungwon-Gu, Sungnam, Kyungki-Do, Korea 462-703 TEL: +82-31-740-8137~8141 FAX: +82-31-740-8145 SAMSUNG OPTO-ELECTRONICS AMERICA, INC. ELECTORONIC IMAGING DIV. 40 Seaview Drive, Secaucus NJ 07094, U.S.A TEL : +1-201-902-0347 FAX: +1-201-902-0429 SAMSUNG TECHWIN MOSC ...
Do you have a question concerning Samsung SCC-3000?
Use the form below
If you did not solve your problem by using a manual Samsung SCC-3000, ask a question using the form below. If a user had a similar problem with Samsung SCC-3000 it is likely that he will want to share the way to solve it.