English dropdown-ico

Manual Cannon 10 STX

38 pages 2.41 mb
Download

Go to site of 38

Summary
  • Cannon 10 STX - page 1

    Owner’s Manual Mag num 5 S T Mag num 10 STX Magnum 10 STX TS ...

  • Cannon 10 STX - page 2

    2 www.cannondownriggers.com Table of Contents T ABLE OF CONTENTS Introduction .................................................................................................................................................................. 3 Warranty / Servic e Information ........................................................................... ...

  • Cannon 10 STX - page 3

    3 www.cannondownriggers.com Introduction Introduction Overvie w Thank you for purchasing the Canno n Magnum electric downri gger. We have designed your n ew do wnrig- ger to be an accurate and reliable tool that will enhan ce fishing control and improve your ability to catch fish. This manual covers installation and the functions of the Magnum 5 ST ...

  • Cannon 10 STX - page 4

    4 www.cannondownriggers.com Product Warranty CANNON LIMITED W ARRANTY Johnson Outdoors Marine Electronics, Inc. warrants to the original purchaser that if the accompanyi ng product (see exclusions below) proves to be defective in material or workmanship within the following warranty periods, Johnson Outdoors Marine Electronics, Inc. will, at its op ...

  • Cannon 10 STX - page 5

    5 www.cannondownriggers.com Product Overview Introduction to Controlled Dep th Fish ing Undoubtedly there are many fishermen familiar with the methods and use of controlled depth fishi ng. During the mid 1960's the state of Michi gan intro- duced Pacific salmon into the Great Lakes in an at- tempt to revitalize its sport fishing industry. From ...

  • Cannon 10 STX - page 6

    6 www.cannondownriggers.com Installation Arrows Indicate Typical Mounting Locations Installing the Base on Your Boat Decks up to 7/16" thick Where access to the underside of the deck is not available, the mounting base can be mounted using wellnuts. Use the base as a template to mark locations and drill four wellnut cleara nce h oles. Mount th ...

  • Cannon 10 STX - page 7

    7 www.cannondownriggers.com Installation Decks thinner than 1/4" Use a Cannon deck plate (PN 2200693) to prevent deflection and add stability to decks thinner than 1/4". Use the deck plate as a template to mark the hole locations. If access to the undersi de of the deck is not available, the deck plate can be mounted using scre ws and wel ...

  • Cannon 10 STX - page 8

    8 www.cannondownriggers.com INSTALLING THE BOOM AN D B ALL HOOK 1) Remove the ball hook collar, ball hoo k, and 1/4 -20 nut from the included hardware bag assembly. 2) Thread the nut onto the ball hook, then thread the ball hook into the ball hook collar. Do not tighten yet. (Figure 1) 3) Slide ball hook collar ont o the end of the boom a nd leave ...

  • Cannon 10 STX - page 9

    9 www.cannondownriggers.com FIGURE 5 FIGURE 6 FIGURE 7 FIGURE 8 6) Insert the 1/4-20 nylon locknut into the hex pocket on the nose of the frame (motor side of frame). (Figure 5) 7) Insert 1/4-20 x 2” bolt into reel side of frame nose. With a Phillips head screw driver, thread bolt into the nylon locknut from step 6. Tighten bolt until the end of ...

  • Cannon 10 STX - page 10

    10 www.cannondownriggers.com BOOM END PULLEY Telescopic Boom 1) Remove boom end assembly from hard wa re bag. 2) Remove #8 self tapping screw from h ard ware bag. 3) Insert boom end post into end of the small tube of the telescopic boom assembly. (Figure 9) 4) Align hole in boom post with hole in small end tube. (Figure 10) 5) Secure boom end with ...

  • Cannon 10 STX - page 11

    11 www.cannondownriggers.com REMOVABLE SPOOL COVER Your new downrigge r com es with a removable spool cover. By removing this cover, you are able to gain easy access to your spooled cable and ea sy spool removal. This feature allows you to easily ac- cess tangled line, get it repaired and get you back into action quickly. This feature also allows y ...

  • Cannon 10 STX - page 12

    12 www.cannondownriggers.com Installation ATTACHING THE RO D H OLDER(S) The locking rod holder(s) incorporate a l ocking tooth design which can be easily adj usted every 15° with the soft grip knob. The symmetrical design will al- low mounting of the rod holder on either side of the downrigger or two rod hold ers at the same time. The unique two p ...

  • Cannon 10 STX - page 13

    13 www.cannondownriggers.com Installation TERMINA TING THE DOWNRIGGER CABLE TIP: Use only straight cable whe n routing through the terminator. Worn or kin ked cable can be stressed and may break prematurely when retri eving trolling weights. A TT ACHING THE LINE RE LEASE (UNI-RELEASE) The Cannon Uni-Release attache s directly to the downrigger weig ...

  • Cannon 10 STX - page 14

    14 www.cannondownriggers.com USING THE INCLUDED POWE R LOSS MANUAL CRANK HANDLE In case of a dead battery, your downrigger come s equipped with a power loss manual cra nk handle. This handle allows for the retrieval of your weight should you lose power or have an electrical failure. To utilize the handle follow the below steps. WARNING: LOOSENING O ...

  • Cannon 10 STX - page 15

    15 www.cannondownriggers.com Installation Wiring Y our Downrigger Your Boat's Electrical Condition It is important to make sure that your boat is properly set up before installing your Magnum with Positive Ion Control (PIC). Whenever a boat is in water, various subm erged parts intera ct to create weak electrical currents. These weak electrica ...

  • Cannon 10 STX - page 16

    16 www.cannondownriggers.com Installation FUSE / BREAKER SPECIFICATIONS: An over-current protection device (circuit breake r or fuse) must be used with this downrigger. Coast Guard re- quirements dictate that each ungroun de d current-carrying conductor must be pr otected by a manually reset, trip- free circuit breaker or fuse. The following breake ...

  • Cannon 10 STX - page 17

    17 www.cannondownriggers.com Getting Started GETTING ST ARTED Manual Descent: Fast or Slow By turning the clutch kn ob gently clockwise (toward the boom), you can let your trolling weight descend a s fast or as slowly as you wish. Turning the knob co unter- clockwise (away from the boom ) stop s the weight. This gives you control to let it plunge r ...

  • Cannon 10 STX - page 18

    18 www.cannondownriggers.com Getting Started Adjusting the Depth Meter The Cannon Depth Meter provide s non-slip accu- racy, plus easy resetting. To reset, just slide the meter away from the reel until the gears are disengag ed. Spin meter gear to change setting. NOTE: Actual fishing de pth may vary from depth shown on meter due to trolling speed a ...

  • Cannon 10 STX - page 19

    19 www.cannondownriggers.com Fishing Theor y Fishing With Your Downrigger Release some line from your rod and re el so that the lure is anywhere from 5 to 100 feet behind the bo at. This is called drop back. Attach the fishing line firmly into the line release. Place the fishing rod in the rod holder and reel up the slac k so that you r rod has a s ...

  • Cannon 10 STX - page 20

    20 www.cannondownriggers.com How the Positive Ion Control Sy stem Works The PIC system uses an internal circuit that passes the voltage through the drive train of the Magnum to the shaft. The shaft contacts the cable by means of a ball bearing, spring and, lastly, a one direction button hea d screw. Care must be take n to ensure contact between the ...

  • Cannon 10 STX - page 21

    21 www.cannondownriggers.com Blowback Calculations Blowback Simply stated, blowback is what happe n s to the downrigger weight when you pull it through the water behind your boat. As your speed increases, so doe s the horizontal distance betwee n the weig ht and your downrigger. The faster you go, the farther the weight is behind you. The farther t ...

  • Cannon 10 STX - page 22

    22 www.cannondownriggers.com Ten Good Trolling Tips 1) Test your lures over the boat side before sending them down and back. Do this to make sure the lure wig- gles and wobbles properly without goi ng belly up or wandering off. Some lures can be adjusted, fine tuned actually, to impart maximum action. For example, a slight bend in the tail of a spo ...

  • Cannon 10 STX - page 23

    23 www.cannondownriggers.com Troubleshooting Troubleshooting PROBLEM: In the UP or AUTO-UP mode the downrigge r stops periodically or the circuit breaker trips repeatedly. SOLUTION: • Low battery. The battery voltage at the power cord is less than 11.5 volts (measure with a volt meter while the downrigger is pulling up the we ight). • Power cab ...

  • Cannon 10 STX - page 24

    24 www.cannondownriggers.com Parts List 1902300 Magnum 5 ST ...

  • Cannon 10 STX - page 25

    25 www.cannondownriggers.com Parts List In the U.S.A., replacement part s may be ordered directly from CANNON Parts Dep t., 121 Power Drive, Mankat o, Minnesota 56001. . Be sure to provide the MODEL and SE- RIAL numbers of your downrigger when ordering parts. Please us e the c orrect part num bers from the parts list. Payment for any parts ordered ...

  • Cannon 10 STX - page 26

    26 www.cannondownriggers.com Parts List 1902301 Magnum 5 ST /E ...

  • Cannon 10 STX - page 27

    27 www.cannondownriggers.com Parts List In the U.S.A., replacement parts may be ordered directly from CANNON Parts Dept., 121 Power Drive, Mankato, Minnesota 56001. B e sure to provide the MODEL and SERIAL numbers of your downrigger when orderin g parts. Please use t he correct part numbers from the parts list. Payment for any part s ordered from t ...

  • Cannon 10 STX - page 28

    28 www.cannondownriggers.com Parts List 1902305 Magnum 10 STX ...

  • Cannon 10 STX - page 29

    29 www.cannondownriggers.com Parts List In the U.S.A., replacement parts may be ordered directly from CANNON Parts Dept., 121 Power Drive, Mankato, Minnesota 56001. B e sure to provide the MODEL and SERIAL numbers of your downrigger when orderin g parts. Please use t he correct part numbers from the parts list. Payment for any part s ordered from t ...

  • Cannon 10 STX - page 30

    30 www.cannondownriggers.com Parts List 1902306 Magnum 10 STX /E ...

  • Cannon 10 STX - page 31

    31 www.cannondownriggers.com Parts List In the U.S.A., replacement parts may be ordered directly from CANNON Parts Dept., 121 Power Drive, Mankato, Minnesota 56001. B e sure to provide the MODEL and SERIAL numbers of your downrigger when orderin g parts. Please use t he correct part numbers from the parts list. Payment for any part s ordered from t ...

  • Cannon 10 STX - page 32

    32 www.cannondownriggers.com Parts List 1902310 Magnum 10 STX TS ...

  • Cannon 10 STX - page 33

    33 www.cannondownriggers.com Parts List In the U.S.A., replacement parts may be ordered directly from CANNON Parts Dept., 121 Power Drive, Mankato, Minnesota 56001. B e sure to provide the MODEL and SERIAL numbers of your downrigger when orderin g parts. Please use t he correct part numbers from the parts list. Payment for any part s ordered from t ...

  • Cannon 10 STX - page 34

    34 www.cannondownriggers.com Parts List 1902311 Magnum 10 STX TS /E ...

  • Cannon 10 STX - page 35

    35 www.cannondownriggers.com Parts List In the U.S.A., replacement parts may be ordered directly from CANNON Parts Dept., 121 Power Drive, Mankato, Minnesota 5600. B e sure to provide the MODEL and SERIAL numbers of your downrigger when orderin g parts. Please use t he correct part numbers from the parts list. Payment for any part s ordered from th ...

  • Cannon 10 STX - page 36

    36 www.cannondownriggers.com Wiring Diagram Magnum Series Wiring Diagram ...

  • Cannon 10 STX - page 37

    37 www.cannondownriggers.com THIS P AGE INTENTIONALL Y LEFT BLANK ...

  • Cannon 10 STX - page 38

    X www.cannondownriggers.com ENVIRONMENTAL COMPLIANCE STA TEMENT: It is the intention of Johnson Outdoors Mari ne Electronics, Inc. to be a responsible corporate citizen, operating in compliance with known and applicable environmental regulations, and a good neighbor in the communities where we make or sell our products. WEEE Directive: EU Directive ...

Manufacturer Cannon Category Fishing Equipment

Documents that we receive from a manufacturer of a Cannon 10 STX can be divided into several groups. They are, among others:
- Cannon technical drawings
- 10 STX manuals
- Cannon product data sheets
- information booklets
- or energy labels Cannon 10 STX
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cannon 10 STX.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cannon 10 STX, service manual, brief instructions and user manuals Cannon 10 STX. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cannon 10 STX.

Similar manuals

A complete manual for the device Cannon 10 STX, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cannon 10 STX by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cannon 10 STX.

A complete Cannon manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cannon 10 STX - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cannon 10 STX, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cannon 10 STX, that we can find in the current document
3. Tips how to use the basic functions of the device Cannon 10 STX - which should help us in our first steps of using Cannon 10 STX
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cannon 10 STX
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cannon 10 STX in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cannon 10 STX?

Use the form below

If you did not solve your problem by using a manual Cannon 10 STX, ask a question using the form below. If a user had a similar problem with Cannon 10 STX it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)