English dropdown-ico

Manual Makita RP0900

28 pages 0.79 mb
Download

Go to site of 28

Summary
  • Makita RP0900 - page 1

    1 INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES DOUBLE INSULA T ION DOUBLE ISOLA T ION DOBLE AISLAMIENT O W ARNING: For your personal safety , READ and UNDERST AND before using. SA VE THESE INSTRUCTIONS FOR FUTURE REFERENCE. A VERTISSEMENT : Pour votre propre sécurité, prière de lire attentivement avant l'utilisation. ...

  • Makita RP0900 - page 2

    2 ENGLISH SPECIFICA TIONS Model RP0900 Collet chuck capacity 1/4" Plunge capacity 0 - 35 mm (0 - 1- 3/8") No load speed (R PM) 27,000/min. Overall heig ht 217 mm (8-17/3 2") Net weight 2.7 kg (6.0 lbs) • Due to our conti nuing program me of research an d development, th e specifications herein are subj ect to change w ithout notice ...

  • Makita RP0900 - page 3

    3 Power tool use and care 16. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for wh ich it was design ed. 17. Do not use t he power t ool if the sw itch does not turn it on and off. Any power tool that canno t be controlled with the switch is dangerou ...

  • Makita RP0900 - page 4

    4 9. Make sure the bit is not cont acting the workpiece before the switch is turned on. 10. Before using the tool on an actual workpiece, let it ru n for a while. W atch for v ibration or wobbling that could indicate improperl y insta lled bit. 11 . Be careful of the bit rotating direction and the feed direction. 12. Do not leave the tool running. ...

  • Makita RP0900 - page 5

    5 CAUTION : • Since excessiv e cutting may cause overload of the motor or diffi culty in controlling the tool, the de pth of cut should not be more than 15 m m (9/16") at a pass when cutting grooves with an 8 mm (5/16") diameter bit. • When cutting groov es with a 20 mm (13/16") diameter bit, the d epth of cut should not be more ...

  • Makita RP0900 - page 6

    6 CAUTION : • Install the bit securely . Always use only the wrenches provided with the tool. A loose or overtightened bit ca n be dangerous. • Do not tigh ten the co llet nut without i nserti ng a bit. It can lead to brea kage of the collet cone. Insert the bit all th e way into the collet cone and tighten the collet nut secur ely with the two ...

  • Makita RP0900 - page 7

    7 A 009751 T e mplet guide (Accessor y) 009752 The templet guide prov ides a sleeve through w hich the bit passes, allow ing use of the tool with temple t patterns. T o install the templet g uide, loosen the screw s on the tool base, insert th e templet guide and then tighten the screws. 1 2 3 009753 Secure the templet to the workpiece. Place the t ...

  • Makita RP0900 - page 8

    8 009755 MAINTENANCE CAUTION : • Always be sure th at the tool is switched of f and unplugged before attempting to perform inspec tion or maintenance. T o maintain product SAFETY and RELIABILITY , repairs, carbon brush insp ection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factor y Service Cen ...

  • Makita RP0900 - page 9

    9 FRANÇAIS SPÉCIFICA TIONS Modèle RP0900 Capacité du mandrin à b ague 1/ 4" Capacité d'ins ertion 0 - 35 mm (0 - 1- 3/8") Vitesse à v ide (T/MIN) 27,000/min. Hauteur hors tout 217 mm (8-17/32") Poids net 2.7 kg (6.0 lbs) • Étant donné l'évolutio n constante de notre prog ramme de recher c he et de dév eloppemen ...

  • Makita RP0900 - page 10

    10 11 . Prévenez tout démarrage acc identel. Assurez-vous que l'interrupteur est en position d'arrêt avant de brancher l'outil. Vous ouvrez la porte aux accident s si vous transportez les outils électri ques avec le doigt sur l'interrupteur ou les bran chez alors que l'interrupteur est en position de marche. 12. Retirez ...

  • Makita RP0900 - page 11

    11 Tableau 1. Gabarit minimum du cordon Intensit é nominale Volts Longueur totale du cordon en pieds 120 V 25 pi 50 pi 100 pi 150 pi Plus de Pas plus de Calibre am é ricain des fils 0 6 18 16 16 14 18 16 14 12 61 0 10 12 16 16 14 12 12 16 14 12 Non recommand é 000173 GEB018-1 RÈGLES DE SÉCURITÉ P ARTICULIÈRES NE vous laissez P AS tromper (au ...

  • Makita RP0900 - page 12

    12 USD201-2 Symboles Les symboles ut ilisés pour l'outil son t indiqués ci-dessous. ･ volts ･ ampères ･ hertz ･ courant alternati f ･ vitesse à vide ･ construction, ca tégorie II ･ tours ou alternan ces par minute DESCRIPTION DU FONCTIONNEMENT AT T E N T I O N : • Assurez-vous toujours que l'outil est hors ten sion et ...

  • Makita RP0900 - page 13

    13 La butée est munie de trois b oulons de réglage hexagonaux qui s'élèv ent ou s'abaissent de 0,8 mm (environ 1/32") p ar rotation . Vou s pouvez fa cilement obtenir trois dif férentes profondeurs de coupe sans modifier le réglage de la tige d'arrêt. Ajustez le boulon inférieur à la plus grande profon deur de coupe dé ...

  • Makita RP0900 - page 14

    14 UTILISA TION Placez la base de l'outil sur la piè ce à couper sans que la fraise ne touche quoi que ce soit. Mettez ensuite l'outil sous tension e t attendez que la frai se ait atteint sa pleine vitesse. Abaissez l e bâti et faites avancer l'outil sur la pièce, en maintenant la base de l'outil bien en contact avec la piè ...

  • Makita RP0900 - page 15

    15 Guide de gabarit (acce ssoire) 009752 Le guide de gabarit présente un m anchon à travers lequel passe la fraise, permettan t d'utiliser l'outil pour la reproduction exacte d'un mod èle donné. Pour installer le guide de gabari t, desserrez les vis à tê te plate de la base , insérez l e guide, puis resser rez les vis. 1 2 3 0 ...

  • Makita RP0900 - page 16

    16 ENTRETIEN AT T E N T I O N : • Assurez-vous toujours que l'outil est hors ten sion et débranché avant d'y effectuer tout travail d'inspection ou d'e ntretien. Pour maintenir la SÉCURITÉ et la FIABILITÉ du produit, les réparati ons, l'inspection et le remplacement des charbons, et tout a utre travail d'entret ...

  • Makita RP0900 - page 17

    17 ESP AÑOL ESPECIFICACIONES Modelo RP0900 Especificaciones el éctricas en Méxi co 120 V 8 A 50/60 Hz Capacidad del ajustador del mandr il 6,3 mm (1/4") Capacidad de inserción 0 - 35 mm (0 - 1- 3/8") Revoluciones p or minuto (r .p.m.) 27 000 r/min Altura tot al 217 mm (8-17/3 2") Peso neto 2,7 kg (6,0 lbs) • Debido a nues tro p ...

  • Makita RP0900 - page 18

    18 10. Utilice equipos de seguridad. Póngase siempre protección p ara los ojos. El equipo de seguridad tal com o máscara contra el polvo, zapatos de seguridad antiderrap antes, casco rígido y prote cción para o ídos utilizado en l as condiciones apropiadas reducirá el riesgo de sufrir heridas perso nales. 11 . Evite el encendido accident al ...

  • Makita RP0900 - page 19

    19 Tabla 1. Calibre m í nimo para el cable Volts Longitud total del cable en metros 120 V~ 7,6 m (25 ft) 15,2 m (50 ft) 30,4 m (100 ft) 45,7 m (150 ft) M á s de No m á s de Calibre del cable (AWG) 0 A 6 A 1 81 61 61 4 18 16 14 12 6 A 10 A 10 A 12 A 16 16 14 12 12 A 16 A 14 12 No se recomienda Amperaje nominal 000173 GEB018-1 NORMAS ESPECÍFICAS ...

  • Makita RP0900 - page 20

    20 resultar en les iones personales graves. USD201-2 Símbolos A continuación se muestran los símbolos utilizados para la herramienta. ･ volts o v oltios ･ amperes o amperios ･ hertz ･ corriente alterna ･ velocidad en v acío ･ Construcción clase II ･ revoluciones o alternaciones por minuto DESCRIPCIÓN DEL FUNCIONAMIENTO PRECAUCI? ...

  • Makita RP0900 - page 21

    21 Bloque de tope 1 2 3 4 5 009746 El bloque de to pe cuenta con tres pernos hexagonales de ajuste los cuales se elevan o se bajan 0,8 mm (1/32" aprox.) por giro. Puede fá cilmente obtener tres profundidades disti ntas de corte al u sar estos pernos hexagonales de ajuste sin tener que reajusta r la vara de tope. Ajuste el perno hex agonal de ...

  • Makita RP0900 - page 22

    22 Inst alación o ex tracción de la fresa 009748 PRECAUCIÓN: • Coloque la broca firmemente . Utilice siempre la s llaves incluidas con la herramienta. Una fresa floja o apretada en ex ceso puede ser peligrosa. • No apriete la tuerca ajust adora sin insert ar una broca. Esto podría oca sionar una rotura del cono sujetador . Inserte la fre sa ...

  • Makita RP0900 - page 23

    23 si el costado de la pieza de trabajo no es recto, la gu ía recta no puede usarse. En este caso, sujete un tablero recto a la pieza de trabaj o con la abrazadera y úselo como una guía contra la base de la rebajadora. Alimente la herramienta haci a la dirección de la flecha. A 009751 Guía de plantilla (acces orio) 009752 La guía de plantilla ...

  • Makita RP0900 - page 24

    24 009755 MANTENIMIENTO PRECAUCIÓN: • Asegúrese siempre que la herramienta e sté apagada y descone ctada antes de inte ntar realizar una inspección o mantenimiento. Para mantener la SEGURI DAD y FIABILIDAD del producto, las rep araciones, la in spección y sustitución de las escobillas de carbón, y cualquier otro mantenimiento o ajuste de b ...

  • Makita RP0900 - page 25

    25 ...

  • Makita RP0900 - page 26

    26 ...

  • Makita RP0900 - page 27

    27 ...

  • Makita RP0900 - page 28

    28 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry pro ...

Manufacturer Makita Category Router

Documents that we receive from a manufacturer of a Makita RP0900 can be divided into several groups. They are, among others:
- Makita technical drawings
- RP0900 manuals
- Makita product data sheets
- information booklets
- or energy labels Makita RP0900
All of them are important, but the most important information from the point of view of use of the device are in the user manual Makita RP0900.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Makita RP0900, service manual, brief instructions and user manuals Makita RP0900. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Makita RP0900.

Similar manuals

A complete manual for the device Makita RP0900, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Makita RP0900 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Makita RP0900.

A complete Makita manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Makita RP0900 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Makita RP0900, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Makita RP0900, that we can find in the current document
3. Tips how to use the basic functions of the device Makita RP0900 - which should help us in our first steps of using Makita RP0900
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Makita RP0900
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Makita RP0900 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Makita RP0900?

Use the form below

If you did not solve your problem by using a manual Makita RP0900, ask a question using the form below. If a user had a similar problem with Makita RP0900 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)