English dropdown-ico

Manual Woods Equipment CZR2242B

74 pages 5.65 mb
Download

Go to site of 74

Summary
  • Woods Equipment CZR2242B - page 1

    P ARTS / OPERA T OR'S MANUAL MOW’N MACHINE MAN0864 REV A 12-2010 CZR2242B 87231 1G 22HP B&S W/42” SIDE DISCHARGE (S/N 000050 AND ABOVE) CZR2652B 872313G 26HP B&S W/52” SIDE DISCHARGE (S/N 000050 AND ABOVE) Includes Maintenance Instructions RF4166230 ...

  • Woods Equipment CZR2242B - page 2

    CALIFORNIA Proposition 65 W arning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer , birth defects and other reproductive harm. Californie Proposition 65 A vertissement Les échappements des moteurs diesel et certains de leurs composés sont reconnus par l’Etat de Californie pour être canc? ...

  • Woods Equipment CZR2242B - page 3

    3 WOODS IMPORT ANT MESSAGE TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods® dealer . Read manual instructions and safety rules. Make sure all items on the Dealer ’s Pre-Delivery and Delivery Check Lists in the Set-Up instructions are completed before releasing equipment to the owner . The dealer ...

  • Woods Equipment CZR2242B - page 4

    4 WOODS T ABLE OF CONTENTS FIGURES P AGE SAFETY ....................................................................................................................................................... 5-1 1 SET -UP INSTRUCTIONS ......................................................................................................................... 1 ...

  • Woods Equipment CZR2242B - page 5

    5 WOODS SAFETY NOTICE !!! Unauthorized modications may present extreme safety hazards to operators and bystanders and could also result in product damage. Woods strongly warns against, rejects and disclaims any modications, add-on accessories or product alterations that are not designed, developed, tested and approved by Woods Engineering Dep ...

  • Woods Equipment CZR2242B - page 6

    6 WOODS SAFETY Site preparation and circumstances - Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform the job. Only use accessories and attachments approved by the manufacturer . - Clear the area to be mowed of objects such as rocks, toys, wire or other debris that may be picked up or throw ...

  • Woods Equipment CZR2242B - page 7

    7 WOODS SAFETY Machine preparation - Check operator presence interlock system and brake operation. Adjust or repair any problems before using. - Do not tamper with or defeat safety devices. Keep guards, shields and interlock safety devices in place and in proper working condition. They are for your protection. - Keep all fasteners such as nuts, bol ...

  • Woods Equipment CZR2242B - page 8

    8 WOODS SAFETY Starting - Start only according to instructions in this manual or on the machine. - Before attempting to start the engine, make sure: - the parking brake is on; - the PT O is disengaged; - the traction drive is in NEUTRAL. - When starting the engine, make sure hands and feet are clear of the blades. - Do not start the machine while s ...

  • Woods Equipment CZR2242B - page 9

    9 WOODS W ARNING SAFETY MANEUVERING SAFEL Y In general - Slow down before turning. - Do not mow in reverse unless absolutely necessary . Always look behind and down for small children and pets before and during backing. - Be aware when approaching blind corners, shrubs, trees, tall grass or other objects that may obscure vision. - If tires lose tra ...

  • Woods Equipment CZR2242B - page 10

    10 WOODS SAFETY MAINTENANCE SAFETY In general - Maintain machine according to manufacturer's schedule and instructions for maximum safety and best mowing results. - Park machine on level ground. - Never allow untrained personnel to service ma- chine. - Adjust or repair only after the engine has been stopped and the blades have quit rotating. - ...

  • Woods Equipment CZR2242B - page 11

    11 WOODS SAFETY BA TTER Y Battery acid is caustic and fumes are explosive and can cause serious injury or death. T o reduce the risk of personal injury when working near a bat- tery: - When working with battery acid, use protective equipment such as, but not limited to, goggles, face shield, rubber gloves and apron. - Avoid leaning over a battery . ...

  • Woods Equipment CZR2242B - page 12

    12 WOODS SET UP INSTRUCTIONS TOOLS REQUIRED FOR ASSEMBL Y - Wrecking bar - Claw hammer - Sockets: 1/2”, 15/16 - Wrenches: 18mm, 1/2”, 9/16”, 3/4”, 15/16” - T ire pressure gauge NOTE: All references below to the “right” or “left” are with respect to an operator at the controls. 1. UNCRA TE UNIT a) Discard packing materials. Loosen ...

  • Woods Equipment CZR2242B - page 13

    13 WOODS 4. FINAL PREP ARA TIONS - Check the engine and hydraulic oil levels. T op off with the correct oil if necessary . Use 10W30 motor oil for the engine. Use fresh, clean 20W50 motor oil for the hydraulic system. - Insure Battery cables are connected properly . Battery acid is caustic. Fumes are explosive and can cause serious injury or death. ...

  • Woods Equipment CZR2242B - page 14

    14 WOODS LABELS F N N 4165616 R F N R 4165615 N PTO SWITCH 4165662 bORDER IS NOT BLUE, BORDER IS WHITE. ...

  • Woods Equipment CZR2242B - page 15

    15 WOODS LABELS ...

  • Woods Equipment CZR2242B - page 16

    16 WOODS LABELS 4165610 - Leer el manual del operador . No permitir que personas no capacitadas para ello usen la máquina. - Mantener los protectores en su lugar y sus tornillos debidamente fijados. - Antes de limpiar , ajustar o reparar este equipo, apagar todos los mandos, aplicar el freno de estacionamiento y apagar el moto r. - Mantener las ma ...

  • Woods Equipment CZR2242B - page 17

    17 WOODS LABELS ...

  • Woods Equipment CZR2242B - page 18

    18 WOODS At operator's right side KEYSWITCH (K) - The keyswitch has three positions: OFF , RUN , and ST ART . Insert the key and turn it clockwise to move the switch from OFF to RUN . T urn it further to ST ART and hold to engage the starter . Release the key and the switch will return to RUN from ST ART . T urn the key counterclockwise to OFF ...

  • Woods Equipment CZR2242B - page 19

    19 WOODS CONTROLS FUEL SELECT OR V AL VE (U) The fuel tank selector valve is located behind the seat. The fuel tank selector valve has three positions: Off : The tank selector is of f when the lever points down. The selector should be of f whenever the machine is transported or stands unused for any length of time. Shutting off the fuel supply avoi ...

  • Woods Equipment CZR2242B - page 20

    20 WOODS CONTROLS Reverse movement - T o move the machine straight back, pull both traction levers back equally from their neutral position. Reverse speed increases as the levers are moved back farther . Maximum reverse speed is reached when the levers hit the rear of the forward-reverse slot. When moving in reverse, push- ing the levers forward sl ...

  • Woods Equipment CZR2242B - page 21

    21 WOODS CONTROLS P ARKING BRAKE (R) - Pull the parking brake lever up and back to put the parking brake ON. Push it forward and down to put the parking brake OFF . The parking brake must be ON to start the engine. It must also be ON to keep the engine running if the operator leaves the seat. The parking brake must be OFF to keep the engine running ...

  • Woods Equipment CZR2242B - page 22

    22 WOODS PRE-OPERA TION CHECK LIST (OPERA TOR’S RESPONSIBILITY) ___ Review and follow all safety rules and safety decal instructions. ___ Check that all safety decals are installed and in good condition. Replace if damaged. ___ Check to make sure all shields and guards are properly installed and in good condition. Be sure that either the discharg ...

  • Woods Equipment CZR2242B - page 23

    23 WOODS FUELING - Fill fuel tank with good quality , clean, unleaded regular gasoline. Do not use hi-test fuel. - Use a funnel to avoid spilling. W ARNING TO CHECK OR ADD FUEL: – Do it outdoors – Do not smoke – Stop engine; allow to cool – Fill to one inch below bottom of ller neck – Do not overll – Clean up spilled fuel BEFORE S ...

  • Woods Equipment CZR2242B - page 24

    24 WOODS OPERA TION OPERA TING NOTES - Practice at slow engine and travel speeds with the PTO of f until fully familiar with the controls. - For normal cutting the throttle should be set at the full open position. By using the traction levers to speed up or slow down the machine during use, maximum control and cutting efciency can be maintained. ...

  • Woods Equipment CZR2242B - page 25

    25 WOODS CUTTING 1. Place the discharge chute in the down position or correctly t a grass collector or mulcher plate. 2. Sit in the seat. 3. Start the engine. 4. Turn the blades on by pulling up on the PT O switch. Do not start the blades at full throttle. Instead, use the slowest throttle setting that will al- low the engine to pick up the blad ...

  • Woods Equipment CZR2242B - page 26

    26 WOODS MAINTENANCE CHART E C N A N E T N I A M N O I T A R E P O n e e w t e b s e m i t m u m i x a m e r a s l a v r e t n i e s e h T . b o j g n i o g n o n a s i e c n a n e t n i a M . s n o i t i d n o c e r e v e s r e d n u n e t f o e r o m m r o f r e P . s n o i t a r e p o e c n a n e t n i a m 5 T S R I F S R U O H E R O F E B H C A ...

  • Woods Equipment CZR2242B - page 27

    27 WOODS MAINTENANCE RECORD NOTES ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ______________________ ...

  • Woods Equipment CZR2242B - page 28

    28 WOODS CHECK DAIL Y Operator Presence Interlock System - Start Operation For the engine to crank, the parking brake must be on, the PTO (blades) of f and traction levers in the neutral lock position. Sit in the seat and check, one by one, if the engine will crank with the parking brake off, the blades on, and either traction lever out of neutral ...

  • Woods Equipment CZR2242B - page 29

    29 WOODS MAINTENANCE LUBRICA TION Every 50 hours of operation, lubricate the following points (1-3) with grease: 1. Deck lift lever (1 point) 2. Deck lift pivots (4 points) 3. Pull arms (2 points located at the front of the cutterdeck) 4. Caster wheel pivots (2 points) (Lubricate every 500 hours or once a year) NOTE ON BLADE SPINDLES - The blade sp ...

  • Woods Equipment CZR2242B - page 30

    30 WOODS SP ARK PLUGS Remove each plug and check condition. - Good operating conditions are indicated if the plug has a light coating of grey or tan deposit. - A white blistered coating indicates overheating. A black coating indicates an “over rich” fuel mixture. Both may be caused by a clogged air cleaner or improper carburetor adjustment. - D ...

  • Woods Equipment CZR2242B - page 31

    31 WOODS MAINTENANCE DUAL ELEMENT AIR CLEANER Engines equipped with dual element air cleaners have a paper air cleaner element with an oiled, foam precleaner element on the dirty side of the paper element. Both should be inspected regularly and maintained. Clean and re-oil precleaner element every 25 hours (more often under dusty conditions). 1. Di ...

  • Woods Equipment CZR2242B - page 32

    32 WOODS ENGINE COOLING Continued operation with a clogged cooling system will cause severe overheating and can result in en- gine damage. - Daily : Clean air intake screen V . - Every 100 hours : Clean cooling ns beneath blower housing H with reference to information in the engine manufacturer's manual. SPECIFIC TORQUES S T L O B E D A Lm ...

  • Woods Equipment CZR2242B - page 33

    33 WOODS MAINTENANCE TRANSAXLES Inattention to proper safety , operation, or maintenance procedures could result in personal injury , or damage to the equipment. Woods recommends returning the machine to your authorized Woods dealer for service or repair . Perform transaxle maintenance with the engine off, spark plug wires disconnected and PTO dise ...

  • Woods Equipment CZR2242B - page 34

    34 WOODS BLADE BALANCE Blade balance must be maintained at 5/8 oz-in (19.4 g-cm) or less. Failure to keep blades balanced causes excess vibration, wear , and shortened life of most components of the machine. T o balance a blade: 1. Sharpen blade rst. 2. Balance the blade at the center . 3. Attach a 1/8 oz (3.9 g) weight at a distance 5" (12 ...

  • Woods Equipment CZR2242B - page 35

    35 WOODS DECK LEVELING 1. Park the machine on a smooth, level surface. Raise the deck to the transport position. 2. Lower the deck onto a set of equal height blocks under the rear corners of the deck. Place an- other set of blocks under the front of the deck so that the deck top is pitched forward 1/8". NOTE: The front and rear of the deck are ...

  • Woods Equipment CZR2242B - page 36

    36 WOODS ADJUSTMENTS FIGURE 1 P ARKING BRAKE NOTE: There are 2 brakes, 1 on each transaxle. The parking brake should keep the machine from moving. T o check the parking brake, park the ma- chine on a level surface, open the bypass valves and set the parking brake to ON . Attempt to move the machine forward and backward by pushing it. If the machine ...

  • Woods Equipment CZR2242B - page 37

    37 WOODS HYDROST A TIC TRANSAXLE ADJUST - MENTS A turnbuckle style hydrostat neutral adjustment is provided. Neutral: 1. Support the machine with the rear wheels of f the ground. Use jackstands or equivalent sup- port. Do not rely only on mechanical or hydraulic jacks. 2. Move the traction levers out into the neutral lock position and raise the sea ...

  • Woods Equipment CZR2242B - page 38

    38 WOODS ADJUSTMENTS ARM REST HEIGHT ADJUSTMENTS 1. Remove acorn nuts 1, plastic washers 2, arm rest 3 and second set of plastic washers 4. 2. Adjust carriage bolts 5 to desired height A, B, or C by pushing on the carriage bolts 5 until they are free from the locking slot, adjusting them to the desired height and then pulling the carriage bolts 5 i ...

  • Woods Equipment CZR2242B - page 39

    39 WOODS BEL T REPLACEMENT HYDRO TRANSAXLE DRIVE BEL T 1. Remove cutterdeck belt (see cutterdeck belt replacement). 2. Disconnect wire I at clutch M . Remove bolts J and remove torque restraint. 3. Using a ratchet with a 9/16" socket, place over nut at location P . Use the ratchet to rotate it enough to remove the transaxle drive belt. 4. Inst ...

  • Woods Equipment CZR2242B - page 40

    ...

  • Woods Equipment CZR2242B - page 41

    41 WOODS P ARTS SECTION P ARTS SECTION ...

  • Woods Equipment CZR2242B - page 42

    42 WOODS FIGURE 1 FRAME-ENGINE/CLUTCH ASSY 4 3 16 19 8 9 20 12 5 10 6 7 18 14 24 15 2 21 22 23 JUMPER HARNESS 26 25 1 13 11 13 17 27 28 ...

  • Woods Equipment CZR2242B - page 43

    ITM P ART NO. DESCRIPTION QTY 43 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 1 FRAME-ENGINE/CLUTCH ASSY 1 4164049 S-FRAME W/LABELS 1 2 64123-89 BOL T -HEX 1/4-20X3/4 1 3 64152-23 1/4-20X3/8 LG SP SCREW 2 4 38665 SOLENOID 1 5 38304-03 BRG-FLANGED PLASTIC 1 6 2721331.7 WLDMT -CLUTCH STOP 1 7 64265-04 LOCKNUT -M8-1.25 2 8 64164-12 KEY -1/4X1/4X1 SQ END ...

  • Woods Equipment CZR2242B - page 44

    44 WOODS 15 24 17 45 45 42 FIGURE 2 TRANSAXLE ASSY ...

  • Woods Equipment CZR2242B - page 45

    ITM P ART NO. DESCRIPTION QTY 45 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 2 TRANSAXLE ASSY 1 4164049 S-FRAME W/LABELS 1 2 4162973 SHAFT -PULLARM MOUNT 1 3 4163957.7 WLDMT -PULL ARM 2 4 4163819 ARM-CONTROL 2 5 4163493 AXLE-LH 1 (INCLUDES ITEMS 4, 25, 26, 27, 32) 6 64163-29 WASHER 2 7 64123-68 BOL T -HEX 5/16-18X1 2 8 64025-02 NUT -HEX 5/16-18 2 9 ...

  • Woods Equipment CZR2242B - page 46

    46 WOODS FIGURE 3 FUEL T ANK/BUMPER & CONTROL P ANEL 4 18 21 17 15 16 24 23 25 16 15 17 26 28 27 13 2 10 22 30 5 14 11 14 29 8 12 7 19 6 3 9 ...

  • Woods Equipment CZR2242B - page 47

    ITM P ART NO. DESCRIPTION QTY 47 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 3 FUEL T ANK/BUMPER & CONTROL P ANEL 1 4164049 S-FRAME W/LABS, 1 2 4165504-1 T ANK-FUEL RH WOODS 1 3 4165503-1 T ANK-FUEL LH WOODS 1 4 4164221.7 BUMPER 1 5 4166245 S-CONTROL P ANEL 1 6 128010-03 S-COVERED KEY 1 7 128010-01 S-KEY SWITCH NUT 5/8-32 1 8 2721505 SWITCH-PTO ...

  • Woods Equipment CZR2242B - page 48

    48 WOODS FIGURE 4 FUEL V AL VE & COVER PLA TE 4 6 5 6 7 12 13 16 16 8 11 7 6 9 6 14 6 12 13 1 2 10 3 7 6 10 11 18 TO ENGINE 17 15 16 6 TO ENGINE ...

  • Woods Equipment CZR2242B - page 49

    ITM P ART NO. DESCRIPTION QTY 49 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 4 FUEL V AL VE & COVER PLA TE 1 4164049 S-FRAME W/LABS 1 2 4165504-1 T ANK-FUEL RH WOODS 1 3 4165503-1 T ANK-FUEL LH WOODS 1 4 64197-001 BL T -TDFM 5/16-18X3/4 4 5 4146655.7 COVER-FRAME, REAR 1 6 88042N HOSE CLAMP 12 7 4162977-001 HOSE-1/4 FUEL LINE 24" 3 8 2188161 ...

  • Woods Equipment CZR2242B - page 50

    50 WOODS FIGURE 5 DECK LIFT ASSEMBL Y 1 9 9 10 16 17 10 8 20 34 24 33 21 29 27 21 22 7 6 19 19 25 18 2 5 15 14 14 4 14 14 15 13 14 14 11 12 11 12 17 16 3 CUTTERDECK 11 31 11 32 26 11 30 28 23 6 2 16 ...

  • Woods Equipment CZR2242B - page 51

    ITM P ART NO. DESCRIPTION QTY 51 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 5 DECK LIFT ASSEMBL Y 1 4164049 S-FRAME W/LABS, 1 2 64205-060 BOL T -MET M12-1.75X50 4 3 4143514.7 WLDMT -DECKLIFT , FRONT 1 4 4163894.7 WLDMT -DECKLIFT REAR 1 5 4109960 WLDMT -DECK LIFT ROD 2 6 64221-02 E-RING .250 2 7 4163891.7 BRKT -LIFT LINK 1 8 2188143 GRIP 1 9 64123-5 ...

  • Woods Equipment CZR2242B - page 52

    52 WOODS FIGURE 6 CASTER ASSEMBL Y ...

  • Woods Equipment CZR2242B - page 53

    ITM P ART NO. DESCRIPTION QTY 53 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 6 CASTER ASSEMBL Y 1 4164049 S-FRAME W/LABS, 1 2 4162986 DUST COVER 2 3 85010N ZERK-1/4-28 2 4 64025-20 NUT -HEX 3/4-16 SLOT U 2 5 64163-26 WASHER 2 6 48043-03C CUP-OUTER BEARING 4 7 48043-04C CONE-OUTER BEARING 4 8 48480 SEAL 2 9 4143675.7 WLDMT -CASTER 2 10 64229-06 LOCKN ...

  • Woods Equipment CZR2242B - page 54

    54 WOODS FIGURE 7 KICKPLA TE/SEA T ASSEMBL Y 13 1 6 7 5 4 3 2 12 12 11 8 9 8 10 12 9 16 17 21 22 23 24 15 26 27 19 20 18 25 14 14 31 32 29 30 28 25 34 ...

  • Woods Equipment CZR2242B - page 55

    ITM P ART NO. DESCRIPTION QTY 55 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 7 KICKPLA TE/SEA T ASSEMBL Y 1 4164049 S-FRAME W/LABS 1 2 4163499 SEA T ASSEMBL Y 1 (INCLUDES ITEMS 4,26,& 27) *4151800 KIT -SEA T ADJUSTER *4139431 KIT -ARM REST 3 4163281.7 PLA TE-SEA T 1 4 4124009 SWITCH-SEA T NO 1 5 64139-14 BL T -WLF 5/16-18X7/8 4 6 33138-09 PIN-CL ...

  • Woods Equipment CZR2242B - page 56

    56 WOODS FIGURE 8 STEERING ...

  • Woods Equipment CZR2242B - page 57

    ITM P ART NO. DESCRIPTION QTY 57 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 8 STEERING 1 4144705 GRIP-HANDLE 2 2 4156297.7 LEVER-TRACTION CNTRL 2 3 4156295 WLDMT -CONTROL BAR, RH 1 * 4156294 WLDMT -CONTROL BAR, LH 1 4 4143673.7 WLDMT -CONTROL BOX RH 1 5 4143674.7 WLDMT -CONTROL BOX LH 1 6 108208 SWITCH DBL POLE 2 7 64197-015 BL T -TDFM 10-32X1/2 TO ...

  • Woods Equipment CZR2242B - page 58

    58 WOODS FIGURE 9 P ARKING BRAKE ...

  • Woods Equipment CZR2242B - page 59

    ITM P ART NO. DESCRIPTION QTY 59 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 9 P ARKING BRAKE 1 4164049 S-FRAME W/LABS, 1 2 4163494 TRANSAXLE, RH 1 3 64197-015 BL T -TDFM 10-32X1/2 TORX 2 4 64168-2 COTTER-HAIRPIN.08X1.19 2 5 4148697 ROD-BYP ASS CONTROL 2 6 4146187 BEARING-FLANGE 1 7 64221-03 E-RING 19MM/.750 1 8 2188155 GRIP 1 9 4163060.7 HANDLE-BRA ...

  • Woods Equipment CZR2242B - page 60

    60 WOODS FIGURE 10 WIRE HARNESS OB PO OP DB WB BRY YB RW GY BR YELLOW W/ BLACK STRIPE RED W/ WHITE STRIPE GREEN W/ YELLOW STRIPE BROWN W/ YELLOW STRIPE ORANGE W/ BLACK STRIPE PURPLE W/ ORANGE STRIPE ORANGE W/ PURPLE STRIPE DARK BLUE YELLOW BROWN Y BLACK GREEN RED B G R WHITE W/ BLACK STRIPE WIRE COLORS PURPLE ORANGE WHITE P O W 2 (BLACK) ENGINE BLO ...

  • Woods Equipment CZR2242B - page 61

    ITM P ART NO. DESCRIPTION QTY 61 ITM P ART NO. DESCRIPTION QTY WOODS 1 4154880 HARNESS-MAIN WIRE 1 2 148082-20 FUSE 20 AMP 2 3 30-419 CABLE-BA TT 4 GA BLK 29" 1 4 4124009 SWITCH-SEA T NO 1 5 4165120 METER-HOUR 1 6 30-180 CABLE-BA TT 4 GA RED 29" 1 7 128010 SWITCH, KEY 1 8 2722325 RELA Y -40AMP SEALED 3 9 2188154 MODULE-DELA Y 1 10 2721505 ...

  • Woods Equipment CZR2242B - page 62

    62 WOODS FIGURE 1 1 42" SIDE DISCHARGE 39 34 38 35 37 36 36 41 43 42 15 33 70 FT -LBS TO RQUE TO 6 2 4 5 3 4 7 20 19 29 23 32 24 26 22 25 28 27 30 31 15 33 40 34 41 43 42 7 6 11 6 9 12 6 10 13 15 16 14 18 1 17 19 4 21 8 6 4 4 20 29 49 50 47 44 48 51 46 45 47 46 52 50 56 54 7 53 55 ...

  • Woods Equipment CZR2242B - page 63

    ITM P ART NO. DESCRIPTION QTY 63 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 1 1 42" SIDE DISCHARGE 1 4164884 S-42 DECK W/LABELS 1 2 4147399 CHUTE-RUBBER 1 3 4149017.7 HINGE-CHUTE_RUBBER 1 4 64123-50 BOL T -HEX 3/8-16X1 7 5 64262-013 BL T -FLG HD 3/8-16 X 1-1/2 2 6 64268-03 NUT -FL NYLON LOCK 3/8-16 10 7 64229-03 LOCKNUT -NYLON 3/8-16 14 8 41 1 ...

  • Woods Equipment CZR2242B - page 64

    64 WOODS FIGURE 12 52" SIDE DISCHARGE 30 49 27 28 18 13 26 29 25 50 25 53 15 23 14 11 16 33 26 29 25 17 24 31 32 49 35 13 23 14 15 16 37 11 34 19 20 14 49 13 11 18 15 23 18 25 28 27 16 45 9 TO DECKLIFT 10 9 8 46 3 7 22 12 14 39 21 40 38 44 46 7 36 5 52 5 4 46 5 51 5 5 5 47 47 48 48 46 46 54 54 48 2 46 1 43 41 42 55 7 6 TO RQUE TO 70 FT -LBS ...

  • Woods Equipment CZR2242B - page 65

    ITM P ART NO. DESCRIPTION QTY 65 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 12 52" SIDE DISCHARGE 1 4163933 S-52 DECK W/LABELS 1 2 4143552.25 GUARD-LH 52" DECK 1 3 4143553.25 GUARD-RH 52" DECK 1 4 41471 15 CHUTE-RUBBER ASSY 1 5 64123-50 BOL T -HEX 3/8-16X1 9 6 64018-1 1 BOL T -CRG 1/2-13X3LG 2 7 64229-03 LOCKNUT -NYLON 3/8-16 24 8 64 ...

  • Woods Equipment CZR2242B - page 66

    66 WOODS FIGURE 13 BEL TS-CUTTERDECK ...

  • Woods Equipment CZR2242B - page 67

    ITM P ART NO. DESCRIPTION QTY 67 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 13 BEL TS-CUTTERDECK 1 4143733 BEL T -52" CUTTERDECK 1 2 4147716 BEL T -42" CUTTERDECK 1 ...

  • Woods Equipment CZR2242B - page 68

    68 WOODS FIGURE 14 DECALS-POWERUNIT 1 2 5 (UNDER SEA T) 17 11 14 7 6 10 16 12 9 15 3 (UNDER FOOTPLA TE) 8 13 4 ...

  • Woods Equipment CZR2242B - page 69

    ITM P ART NO. DESCRIPTION QTY 69 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 14 DECALS-POWERUNIT 1 4165662 LABEL-CONTROL P ANEL 1 2 2000570 LABEL-W ARN FUEL PICT . 2 3 4164525 LABEL-INFORMA TION 1 4 4163972 LABEL-CZR2242B 1 4163973 LABEL-CZR2652B 5 2000590 LABEL-W ARN BA TTERY 1 6 4165616 LABEL-LH TRACTION 1 7 4165615 LABEL-RH TRACTION 1 8 4126804 L ...

  • Woods Equipment CZR2242B - page 70

    70 WOODS FIGURE 16 ACCESSORIES-SUSPENSION SEA T 4 3 1 1 2 6 7 5 ...

  • Woods Equipment CZR2242B - page 71

    ITM P ART NO. DESCRIPTION QTY 71 ITM P ART NO. DESCRIPTION QTY WOODS FIGURE 15 ACCESSORIES-SUSPENSION SEA T 1 64141-6 NUT -WLF 5/16-18 8 2 64262-019 BL T -FLG HD 5/16-18 X 1-3/4 2 3 2720975-07 SP ACER-NYLON 3/8IN 1 4 4164679 SEA T -SUSPENSION 1 (ITEMS 1-4 ARE CONT AINED IN KIT 970394) 5 SLIDER-SEA T 2 6 BL T -TORX 4 7 4163499 SEA T ASSEMBL Y 1 (ITE ...

  • Woods Equipment CZR2242B - page 72

    F-8045 MM & Boundary (Rev . 12/1/2008) W oods Equ ipment Comp any 260 6 South Illinois R oute 2 Post Of fice Box 10 00 Oregon, Illinois 61061 800-319-663 7 tel 800-39 9-663 7 fax www .W oodsEquipment.com LIMITED W ARRANTY (Mow’ n Machine TM Zer o-T urn Mowers and W oods Boundary TM Utility V ehicles) Please Enter Information Below an d Sav e ...

  • Woods Equipment CZR2242B - page 73

    F-8495 MM & Boundary Repair Parts (Rev . 2/15/2006) W oods Equipmen t Company 260 6 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois 610 61 800-319-663 7 tel 800-39 9- 6 63 7 fax www .W oodsEquipment.com LIMITED W ARRANTY (Mo w’ n Machine TM Zero-T urn Mower and W oods Boundary TM Utility V ehicle R eplacement P arts) W oods Equip ...

  • Woods Equipment CZR2242B - page 74

    Woods Equipment Company 2606 South Illinois Route 2 Post Ofce Box 1000 Oregon, Illinois 61061 800-319-6637 tel 800-399-6637 fax www .WoodsEquipment.com ©2008 Woods Equipment Company . All rights reserved. WOODS, the Woods logo, and “T ested. Proven. Unbeatable.” are trademarks of Woods Equipment Company . All other trademarks, trade names, ...

Manufacturer Woods Equipment Category Lawn Mower

Documents that we receive from a manufacturer of a Woods Equipment CZR2242B can be divided into several groups. They are, among others:
- Woods Equipment technical drawings
- CZR2242B manuals
- Woods Equipment product data sheets
- information booklets
- or energy labels Woods Equipment CZR2242B
All of them are important, but the most important information from the point of view of use of the device are in the user manual Woods Equipment CZR2242B.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Woods Equipment CZR2242B, service manual, brief instructions and user manuals Woods Equipment CZR2242B. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Woods Equipment CZR2242B.

Similar manuals

A complete manual for the device Woods Equipment CZR2242B, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Woods Equipment CZR2242B by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Woods Equipment CZR2242B.

A complete Woods Equipment manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Woods Equipment CZR2242B - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Woods Equipment CZR2242B, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Woods Equipment CZR2242B, that we can find in the current document
3. Tips how to use the basic functions of the device Woods Equipment CZR2242B - which should help us in our first steps of using Woods Equipment CZR2242B
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Woods Equipment CZR2242B
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Woods Equipment CZR2242B in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Woods Equipment CZR2242B?

Use the form below

If you did not solve your problem by using a manual Woods Equipment CZR2242B, ask a question using the form below. If a user had a similar problem with Woods Equipment CZR2242B it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)