-
Hotpoint V3D01 - page 1
Instructions f or Installation and Use 3kg T umble Dr yer V3D01 T o the Installer: Bef ore installation, fill in the product details on the back cov er of this book s. The inf ormation c an be f ound on the rating plate. T o the Use: Y ou must read the instructions prior to installing and using the appliance and then retain them f or future ref ere ...
-
Hotpoint V3D01 - page 2
Contents Saf ety Advice Electrical Requirements F eatures - Get to know the main par ts of your Dryer Where to put and vent y our Dr yer How to use y our Dr yer Sor ting your laundry Items not suitable f or dr ying Items requiring special attention The Controls Guide to Dr ying Times How to remo ve and clean the Fluff Filter Caring for y our Dr yer ...
-
Hotpoint V3D01 - page 3
3 For y our safety NEVER ● Allow children to pla y with or otherwise interfere with the dry er . NEVER ● Allow the air inlet at the bac k of the dr yer , the air outlet or vent hose to be obstructed. NEVER ● Direct the vent hose outlet to wards the air intake at the back of the machine. NEVER ● Allow the tumb le dr yer to recycle e xhaust a ...
-
Hotpoint V3D01 - page 4
4 For y our safety AL W A YS ● When the dr yer is not in use , switch off at the w all, remove plug and close the door . AL W A YS ● Comply with the specified electrical requirements. AL W A YS ● Ensure that your dryer is installed correctly and has adequate ventilation. (see, "Where to put and v ent your dr yer .") AL W A YS ● Us ...
-
Hotpoint V3D01 - page 5
5 Electrical Requirements Supply Changing the fuse Moulded plug Changing the plug Rewirable plug Changing the mains cable W ARNING: This appliance must be earthed! REFER TO THE RA TING PLA TE FOR V OL T A GE AND CURRENT REQUIREMENTS. (see diagram for location.) The fle xible mains lead is supplied fitted with a BS1363 plug and with a 13 amp BS1362 ...
-
Hotpoint V3D01 - page 6
6 Features - Get to kno w the main par ts of y our dryer Where to put and vent y our dr yer Y our tumble dryer should NO T be located adjacent to a gas hob , cooker , heater , or eye le vel grill as flames from the bu r ners could cause damage to your machine . The dr yer should be placed where air can freely circulate aroun d it, pref erably near ...
-
Hotpoint V3D01 - page 7
7 Ho w to use y our dryer 1. Plug in, s witch on electricity . 2. Sor t your laundry (see section “Sor ting Y our Laundr y”) 3. Open the door . Check that the fluff filter is clean (see section How to remov e and clean the fluff filter). 4. Load the dr yer placing the clothes carefully in the drum, pushing them well tow ards the back and aw a y ...
-
Hotpoint V3D01 - page 8
8 Sor ting y our laundr y 1. Alwa ys separate laundr y into the correct fabric groups bef ore washing and drying. 2. See that all zips are closed, hooks and eyes are f astened and belt, strings etc. are tied loosely in bows, y ou will nor mally h ave done this f or each item before the w ashing stage. 3. It is impor tant to extr act as much water a ...
-
Hotpoint V3D01 - page 9
9 W ash Care Labels Most of toda y’ s fabrics can be tumble dried in your Dryer with no trouble at all, b ut there are cer tain fabric finishes which should be dried awa y from direct heat. The majority of gar ments now hav e wash-care labels on them, giving full washing and drying instr uctions. These should always be f ol lowed carefully especi ...
-
Hotpoint V3D01 - page 10
10 Items requiring special attention The dr ying requirements of blank ets and bedspreads will, of cou rse, vary tremendously according to size and weight. Some, howe ver ar e simply too big. if y ou hav e difficulty getting them into the Dr y er , the machine will hav e difficulty dr ying them proper ly . Blank ets (and Garments) made from Acr yli ...
-
Hotpoint V3D01 - page 11
11 The Contr ols T urn the Timer cloc kwise to select the required dr ying time. The timer controls the dr ying time f or both heat settings. All you ha ve to do is turn the Timer knob cloc kwise until it lines up with the required time. Never wind the Timer Control anti-c lockwise. This operation also star ts the dr yer , provided the door is clos ...
-
Hotpoint V3D01 - page 12
12 Please note that the Dr ying Times stated below and on appliance control panel are a GUIDE only and dr ying times are aff ected by : Items such as towelling retain a lot of w ater after spinning, also the suggested wash progr amme f or small items such as T -Shir ts may sometimes incor porate a low spin speed which has the same eff ect. Y our dr ...
-
Hotpoint V3D01 - page 13
13 Ho w to remove and c lean the fluff filter Caring f or y our Dr yer T o remo ve the filter A very impor tant par t of your dryer is the fluff filter at the front edge of the drum. It’ s there to trap the par ticles of lint and fluff which are nor mally blo wn aw ay when clothes are dried on the washing-line . if the filter is allowed to become ...
-
Hotpoint V3D01 - page 14
14 If something goes wr ong First, don’t panic! There may be nothing wrong at all. Look for your problem belo w , then check the things we suggest. More often than not, this will give y ou the answer to y our problem, and y ou’ll be able to carr y on without having to telephone y our Service Office. If after this you still cannot get y our mach ...
-
Hotpoint V3D01 - page 15
15 If something is still wrong with your machine after y ou’ve been through the check-list on the pre vious page: 1. Switch off and unplug your machine from the mains . 2. Call your nearest Service Office or local impor ter . When you contact us w e will want to know the f ollowing: 1. Y our name, address and postcode. 2. Y our telephone number . ...
-
Hotpoint V3D01 - page 16
Indesit Company UK Limited, Morley W ay , Peterborough, PE2 9JB K e y Contacts Service Over 1 100 trained specialists, directly employed by us, ensure that you can have complete confidence in both the appliances and ser vices we off er . Repair Service and Inf ormation Help desk UK: 08709 066 066 Monday to Friday , 8am to 7 .30pm Saturday , 8.30am ...
Do you have a question concerning Hotpoint V3D01?
Use the form below
If you did not solve your problem by using a manual Hotpoint V3D01, ask a question using the form below. If a user had a similar problem with Hotpoint V3D01 it is likely that he will want to share the way to solve it.