English dropdown-ico

Manual Allied Telesis Switchblade AT-x900-12

16 pages 0.31 mb
Download

Go to site of 16

Summary
  • Allied Telesis Switchblade AT-x900-12 - page 1

    AlliedW ar e Plus TM OS How T o | C613-16112-00 REV A www .alliedtelesis .com Intr oduction This document describe s some generic configur ation examples f or Quality of Ser vice (QoS) on the AlliedW ar e Plus OS. What information will y ou find in this document? This document pro vides information in the follo wing sections: • 1. Setting the egr ...

  • Allied Telesis Switchblade AT-x900-12 - page 2

    Page 2 | AlliedW ar e Plus™ OS How T o Note: QoS 1. Setting the eg ress rat e 1. Setting the egr ess rate Example 1-1: Setting the eg r ess limit of a switch p or t Commands: interface port1.0.24 egress-rate-limit 25m These commands will set t he egr ess limit of port 24 to 25Mbps. The granular ity is 651kbps. P or t 24 ...

  • Allied Telesis Switchblade AT-x900-12 - page 3

    Page 3 | AlliedW ar e Plus™ OS How T o Note: QoS 1. Setting the eg ress rat e Example 1-2: setting the maximum bandwidth limit per ingr ess port Ingress rate limiting cannot be configur ed on the por t per se , but is achiev ed by cr eating a QoS policy with a bandwidth limited traffic class, and applying that policy to each port. This set of com ...

  • Allied Telesis Switchblade AT-x900-12 - page 4

    Page 4 | AlliedW ar e Plus™ OS How T o Note: QoS 1. Setting the eg ress rat e Example 1-3: Setting the maximu m bandwidth limit f or each user In example 1-1, w e configured an egress rate on ports . But the granularity of that bandwid th limiting was multiples of 651kbps. It is possible to achieve finer -grained limiting using the devices advanc ...

  • Allied Telesis Switchblade AT-x900-12 - page 5

    Page 5 | AlliedW ar e Plus™ OS How T o Note: QoS 1. Setting the eg ress rat e Example 1-4: Setting the maximum ba ndwidth limit f or each IP subnet This example is very similar to example 1-3, exce pt that it is assumed that a whole subnet is attached to each port, not just a single device on each port. This set of commands will set the total egr ...

  • Allied Telesis Switchblade AT-x900-12 - page 6

    Page 6 | AlliedW ar e Plus™ OS How T o Note: QoS 1. Setting the eg ress rat e Example 1-5: Setting the maxi mum bandwidth limit of VLANs mls qos enable class-map cmap2 match vlan 2 class-map cmap3 match vlan 3 class-map cmap4 match vlan 4 mls qos enable mls qos aggregate-police agg1 single-rate 256 3000 5000 exceed-action drop mls qos aggregate-p ...

  • Allied Telesis Switchblade AT-x900-12 - page 7

    Page 7 | AlliedW ar e Plus™ OS How T o Note: QoS 2. Setting the priority on a pack et 2. Setting the priority on a pack et Example 2-1: Setting the La y er 2 (VLA N/802.1p) priority per ingress port Her e we assign differ ent 802.1p values to packets ar riving on differ ent ports. These values ar e also known as the Lay er 2 (L2) or VLAN priority ...

  • Allied Telesis Switchblade AT-x900-12 - page 8

    Page 8 | AlliedW ar e Plus™ OS How T o Note: QoS 2. Setting the priority on a pack et Example 2-2: Setting the La y er 2 (VLAN/802.1p) priority per VLAN This set of commands will set the La yer 2 priority of VLAN2, VLAN3 and VLAN4 traffics pack ets, receiv ed on por ts 1 to 20, to 6, 5 and 4 r espectivel y . mls qos enable class-map cmap2 match v ...

  • Allied Telesis Switchblade AT-x900-12 - page 9

    Page 9 | AlliedW ar e Plus™ OS How T o Note: QoS 2. Setting the priority on a pack et Example 2-3: Setting the La y er 3 (T OS/DCSP) priority per ingr ess por t Use the same configuration pr ovided in Example 2-1 on page 7 , but change the following line: set cos <cos-value> to set dscp <dscp-value> Example 2-4: Setting the La y er 3 ...

  • Allied Telesis Switchblade AT-x900-12 - page 10

    Page 10 | AlliedW are Plus™ OS How T o Note: QoS 3. Setting the egr ess queues 3. Setting the egr ess queues In this section we look at methods f o r dir ecting certain packets into certain queues on the egress port. Example 3-1: Setting the egr ess queue a ccording to the L2 priority of the incoming pack et The priority-to-queue map is a straigh ...

  • Allied Telesis Switchblade AT-x900-12 - page 11

    Page 11 | AlliedW are Plus™ OS How T o Note: QoS 3. Setting the egr ess queues Example 3-2: Setting th e egr ess queue according to the ingr ess por t This set of commands will set the egress queue of an y traffic r eceived fr om por t 1 to egress queue 6, fr om port 2 to egress queue 5 … etc. mls qos enable class-map cmap1 policy-map pmap1 cla ...

  • Allied Telesis Switchblade AT-x900-12 - page 12

    Page 12 | AlliedW are Plus™ OS How T o Note: QoS 3. Setting the egr ess queues Example 3-3: Configuring WRR for egr ess queues This example is used for configuring WRR on egr e ss queues according to the ingr ess por t of the traffic. This set of commands will set the egress queue of an y traffic received fr om por t 1 to egress queue 6, fr om po ...

  • Allied Telesis Switchblade AT-x900-12 - page 13

    Page 13 | AlliedW are Plus™ OS How T o Note: QoS Full QoS scenario - tiered services for a single customer Full QoS scenario - tier ed ser vices for a single customer In this section, we will build up a r elatively complex QoS configuration to support a scenario requiring quite pr ecise control ov er the traffic passing through the switch. The sc ...

  • Allied Telesis Switchblade AT-x900-12 - page 14

    Page 14 | AlliedW are Plus™ OS How T o Note: QoS Full QoS scenario - tiered services for a single customer Identify the types of traffic The differ ent categories of traffic w ill be identified b y the DSCP values in the packets' headers. It is up to the customer to mark the pack ets with the appropriate DSCP values. The DSCP values belongin ...

  • Allied Telesis Switchblade AT-x900-12 - page 15

    Page 15 | AlliedW are Plus™ OS How T o Note: QoS Full QoS scenario - tiered services for a single customer What is requir ed is that: • Gold traffic AL W A YS has pr ecedence over Silv er or Bronze traffic. So , when a Gold pack et arriv es at the egress port, it is transmitted immediatel y , irrespectiv e of how many Silv er or Bronze pack ets ...

  • Allied Telesis Switchblade AT-x900-12 - page 16

    USA Headq u ar ters | 19800 Nor th Cr eek Parkwa y | S u ite 200 | Bothell | WA 98011 | USA | T: +1 800 424 4284 | F: +1 425 481 3895 E u r opea n Headq u ar ters | Via Motta 24 | 6830 Chiasso | Switzerla n d | T: +41 91 69769.00 | F: +41 91 69769.11 Asia-Paci f ic Headq u ar ters | 11 T ai Se ng Li n k | Si ng apor e | 534182 | T: +65 6383 3832 | ...

Manufacturer Allied Telesis Category Switch

Documents that we receive from a manufacturer of a Allied Telesis Switchblade AT-x900-12 can be divided into several groups. They are, among others:
- Allied Telesis technical drawings
- Switchblade AT-x900-12 manuals
- Allied Telesis product data sheets
- information booklets
- or energy labels Allied Telesis Switchblade AT-x900-12
All of them are important, but the most important information from the point of view of use of the device are in the user manual Allied Telesis Switchblade AT-x900-12.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Allied Telesis Switchblade AT-x900-12, service manual, brief instructions and user manuals Allied Telesis Switchblade AT-x900-12. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Allied Telesis Switchblade AT-x900-12.

Similar manuals

A complete manual for the device Allied Telesis Switchblade AT-x900-12, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Allied Telesis Switchblade AT-x900-12 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Allied Telesis Switchblade AT-x900-12.

A complete Allied Telesis manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Allied Telesis Switchblade AT-x900-12 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Allied Telesis Switchblade AT-x900-12, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Allied Telesis Switchblade AT-x900-12, that we can find in the current document
3. Tips how to use the basic functions of the device Allied Telesis Switchblade AT-x900-12 - which should help us in our first steps of using Allied Telesis Switchblade AT-x900-12
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Allied Telesis Switchblade AT-x900-12
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Allied Telesis Switchblade AT-x900-12 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Allied Telesis Switchblade AT-x900-12?

Use the form below

If you did not solve your problem by using a manual Allied Telesis Switchblade AT-x900-12, ask a question using the form below. If a user had a similar problem with Allied Telesis Switchblade AT-x900-12 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)