English dropdown-ico

Manual Graco Series B

40 pages 3 mb
Download

Go to site of 40

Summary
  • Graco Series B - page 1

    Instr uctions - P ar ts A utomatic G40 Air -Assisted Spra y Guns For air- assisted spraying of paints and co atings. For prof essional use only . Appro ved for use in Eur opean explosive atmosp here locations. 4000 psi (28 MP a, 280 bar) Maximum W orking Fluid Pressure 100 psi (0.7 M P a, 7 bar) Maximum Working A ir Pressure See page 3 f or model i ...

  • Graco Series B - page 2

    2 311052H Contents Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V entilate Spray Booth . . . . . . . . . . . . . . . . . . . . . 6 Configure G un and Mani f ol ...

  • Graco Series B - page 3

    Models 311052H 3 Models G40 Standard Spray Gun, 28804 6, Series B • High pressu re spra y gun with Carb ide ball and Car- bide seat. • Includes AAP series tip of choice. G40 Standar d Spray Gun, 24F835, Series B • Air cap optimiz ed for la cquer material. • High pressu re spra y gun with Carb ide ball and Car- bide seat. • Includes AAP se ...

  • Graco Series B - page 4

    Warnings 4 311052H Wa r n i n g s The f ollowing warnings are f or the setup , use, groundin g, maintenance, and repair of this equ ipment. The exclama- tion point symbol alerts you to a gener al warning and the hazard symbol ref ers to procedure -specific risk. Refer bac k to these wa r nings. Additional, product- specific warnings ma y be found t ...

  • Graco Series B - page 5

    Warnings 311052H 5 PRESSURIZED EQUIPMENT HAZARD Fluid from the gun/dispense valv e, leaks , or ruptured components can splash in the e yes or on skin an d cause serious injury . • F ollow Pressure Relief Procedure in this manual, when you stop spra yin g and before cleaning, chec king, or ser vicing equipment. • Tighten all fluid conn ections b ...

  • Graco Series B - page 6

    Installation 6 311052H Installation V entilate Spra y Booth Configure Gun and Manif o ld The gun is supplie d with an internal fluid plug and seals (5, 6, 7). T o use the gun in a circulating system, remov e the internal plug. In a non-circulatin g system, leav e the plug in place to minimiz e flush time. Cir c ulating System 1. Apply anti-seiz e l ...

  • Graco Series B - page 7

    Installation 311052H 7 Install Air Fittings 1. Install the supplied 1/4 in. tube fitting int o the cylin- der (CYL) air port. 2. Install 3/8 in. tube fit tings into the atomization (A T OM) air port and the fan ( F AN) air por t. Gr ound System The f ollowing groundin g instr uctions are minimum requirements f or a system. Y our system may include ...

  • Graco Series B - page 8

    Installation 8 311052H Mount Gun Reciprocating Arm Rod Mount T o mount t he gun on a reciprocating ar m rod [0.5 i n. (13 mm) diameter maxim um]: 1. Inser t the mounti ng bar (A) through the hole in the manif old as shown in F IG . 3. 2. Secure the gun to t he bar by tightening the mount- ing screw (B). Stationary Suppor t T o mount the gun on a st ...

  • Graco Series B - page 9

    Installation 311052H 9 Connect Air Line 1. Install an air/water separator an d an air line filter to ensure a clean, dry air supply to the gun. Dirt and moisture in the line can r uin the appear ance of your finished piece. 2. Install an air pressure regulator on e ach gun air sup- ply line. 3. F or manifolds with separat e f an and atomization por ...

  • Graco Series B - page 10

    Installation 10 311052H Connect Fluid Line 1. Install a fluid filter an d drain valv e(s) close to the pump's fluid outlet. 2. Install a fluid pressur e regulator to control fluid pres- sure to the gun. 3. Install a fluid shutoff v alv e to shut off the fluid supply to the gun. 4. Install an in-line fluid filte r on the gun fluid inlet (F) to ...

  • Graco Series B - page 11

    Setup 311052H 11 Setup Flush Spra y Gun Bef ore running any paint through th e spra y gun: 1. Flush the g un with a solvent that is com patible with the fluid to be spr ay ed, using the low est possible fluid pressure and g rounded metal container . 2. P erf orm Pressure Relief Pr ocedure ; see page 12. Select a Spra y Tip and Air Cap The fluid flo ...

  • Graco Series B - page 12

    Operation 12 311052H Operation Pressure Relief Pr ocedure 1. T urn off the air and f luid supply to the gun. 2. Close the bl eed-type master air v alve (required in the system). 3. T r igger the gun into a g rounded metal wast e con- tainer to reliev e the fluid press ure. 4. Open the pump dr ain valv e (required in the system) to reliev e fluid pr ...

  • Graco Series B - page 13

    Operation 311052H 13 F or a narrow er patter n , supply air to the gu n fan air inlet (or open the f an adjustment v alv e on manifold 288 223). The tip siz e is the primar y controller of the pattern size . Use the f an air only as needed to slightly adjust the pat- ter n size. Appl y Fluid The spra y gun has a b uilt-in lead and lag operat ion. W ...

  • Graco Series B - page 14

    Maintenance 14 311052H Maintenance Daily Gun Care CA UTION Meth ylene chloride with formic or propionic acid is not recommended as a flu s hing or cleaning solv ent with this gun as it will damage aluminum and nylon compo- nents . CAUTION Solv ent left in gun air passages could result in a poor quality pain t finish. Do not use any cleaning method ...

  • Graco Series B - page 15

    Maintenance 311052H 15 General System Maintenance 1. P erf orm Pressure Relief Pr ocedure , page 12. 2. Clean the fluid and air line f ilters daily . 3. Chec k for an y fluid leakage from the gun an d fluid hoses. Tighten fittings or replace equip ment as needed. 4. Flush t he gun before changing co lors and wh ene ver yo u are done operating the g ...

  • Graco Series B - page 16

    Maintenance 16 311052H 7. T urn off the solvent supp ly . 8. P erform Pressure Relief Procedure , page 12. 9. Disconnect the solv ent supply hose from the gun. 10. Dip the end of a soft-bristle brush into a compatib le solv ent. Do not continuously soak the brush's bris- tles with solv ent and do not use a wire brush. 11. With the gun poin ted ...

  • Graco Series B - page 17

    Troubleshooting 311052H 17 T r oubleshooting General T roub leshooting Check all possib le remedies in the troubleshoot ing char ts bef ore disassembling th e gun. Some improper patte r ns are caused by th e improper balance betw een air and fluid. Ref er to Spray Pattern T roubleshoo ting , page 19. Prob lem Cause Solution Fluid leakage throu gh v ...

  • Graco Series B - page 18

    Troubleshooting 18 311052H Fluid needle will not trigger . Loos e or missing fluid needle stop (21) or setscrew (19). Brok en fluid needle (14). Air leaking around piston (20). Swollen piston o-ring (22). Insufficient air pressure on tr igger . Spra y tip (9) is plugged . Fluid filter is plugged. Plug (5) is in incorrect fluid port. Replace stop or ...

  • Graco Series B - page 19

    Troubleshooting 311052H 19 Spra y P attern T r oubleshooting Prob lem Cause Solution Flutter ing spra y . Insufficient flu id supply . Air in paint supply line. Adjust fluid regulator or fill fluid sup- ply tank. Chec k, tighten siphon hose connec- tions , bleed air from pa int line. Spitting spr ay . W or n diffuser-seat ( 10) or needle (14) ball. ...

  • Graco Series B - page 20

    Service 20 311052H Service Items Needed f or Service • 1/16 in. He x Wrench - provided •3 m m H e x W r e n c h • Adjustab le Wrench •4 m m H e x W r e n c h • 5/16 in. Nut Driver • Pliers • Lubricant part no . 111265; see Accessories , page 34, to order • Compatib le Solvent Disassembl y 1. P erform Pressure Relief Procedure , page ...

  • Graco Series B - page 21

    Service 311052H 21 10. If gask et (15) needs to be r eplaced, unscrew the two screw s (18) and separate the flu id housing (2) and piston housin g (1). Inspect gask et (16) and replace if needed. 11. Remove the large o-rin g (22) from the piston and the smaller o-ring (23) from t he piston sh aft. Remov e the tw o o-rings (25, 26) fr om each of the ...

  • Graco Series B - page 22

    Service 22 311052H F IG . 17 SERVICE NOTES: Lubricate threads with anti-seize lubri cant Lubricate with light-weight oil Do not lubricate Torque to 155-165 in-l b (18-19 N•m) Apply semi-permanent an aerobic sealant Torque to 4-5 in-lb (0.45-0.56 N•m) Tighten cap (27) u ntil it bottoms out 4 3 2 8 7 6 5 Cutaway View: Part No. 288044 Gun Shown 30 ...

  • Graco Series B - page 23

    Service 311052H 23 Diffuser Seat Replacement 1. P erf orm Pressure Relief Pr ocedure , page 12. 2. Remove gun from manifold. 3. Remove the air cap reta ining r ing (8), air ca p (30), and spra y tip (9). 4. T r igger the gun (o r remove ca p (27) and spr ings (28, 29)) to pull the needle hous ing off the seat w hile you unscre w the diffuser (10) f ...

  • Graco Series B - page 24

    Parts 24 311052H Pa r t s F IG . 18 2 17 16* 15* 28 7 † 27 29 8 10a SERVICE NOTES: Lubricate threads with anti-seize lub ricant Lubricate with light-weight oil Do not lubricate Torque to 65 in-lb (7.3 N•m) Apply semi-permanent anaero bic sealant Torque to 4-5 in-lb (0.45-0.56 N•m) Tighten cap (27) until it bottoms out Used on non-ci rculating ...

  • Graco Series B - page 25

    Parts 311052H 25 Pa r t s ◆ Model 288044 only . ❖ Model 288046 only . ★ Model 288053 only . ❄ Model 24F835 only . † Included in Fluid Seal Repair Kit 288 136. * Included in Air Seal Repair Kit 28 8171. ✓ Included in Seat Repair Kits 249424 (plastic) or 249456 (carb ide). ✿ Pa r t n o t fo r s a l e . Ref. No. Pa r t No. Description Qt ...

  • Graco Series B - page 26

    Parts 26 311052H P ar t No. 288217 Nor th America Manifold with side fluid ports P ar t No. 288218 International Manif old with side fluid por ts ❄ Not shown. ❖ P ar t No . 288217 only . ◆ P ar t No . 288218 only . Ref. No. P a rt No. Description Qty . 101 MANIFOLD , side fluid po r ts 1 103 1 120388 ❖ FITTING, tube, air inlet; 1/4 in. OD t ...

  • Graco Series B - page 27

    Parts 311052H 27 P ar t No. 288221 Manif old with bottom fl uid por ts ❄ Not shown. Ref. No. P a rt No . Descri ption Qty . 101 MANIFOLD , bottom fluid ports 1 103 120388 FITTING, tube, air inlet; 1/4 in. OD tube x 1/8 npt(m) 1 105 114246 SCREW , set; 5/16; 0.437 in. long 1 107 166846 NIPPLE, SST; 1/4 npsm, straight pipe thre ad x 1/4 np t 2 108 ...

  • Graco Series B - page 28

    Parts 28 311052H P ar t No. 288224 High Pressure Air-Assisted Manifold with side flu id por ts and fan adjustment valve P ar t No. 24C3 43 International Manif old with side fluid por ts ❄ Not shown, optional size . ---- Not sold separately . ❖ P ar t No . 288224 only . ◆ P ar t No. 24C343 only . Ref. No. P art No. Des cription Qty . 101 ---- ...

  • Graco Series B - page 29

    Parts 311052H 29 P ar t No. 288160 Rear P or t Manifold, Nor th Amer ica P ar t No. 288211 Rear P or t Manifold, International ❖ P ar t No . 288160 only . ◆ P ar t No . 288211 only . Ref. No. P ar t No. Description Qty . 101 MANIFOLD , aluminum 1 103 FITTING, fl uid path 2 15H521 ❖ 1/4 npsm 15J003 ◆ #5 JIC 105 116475 SCREW , SHCS, M4 x 12 2 ...

  • Graco Series B - page 30

    Notes 30 311052H Notes ...

  • Graco Series B - page 31

    AAP Series Tip and Air Cap Selection Charts 311052H 31 AAP Series Tip and Air Cap Selection Char ts AAP Series Precision Spray Tips . * Tips are tested in w ater . † Tip sizes include a 150 mesh tip filter Air Cap Order desired tip (P ar t No . AAPxxx) where xxx is the size code f or the char t. Tips are physically marked with Xxxx, where xxx is ...

  • Graco Series B - page 32

    LTX Series RAC Tip Selectio n Charts 32 311052H L TX Series RA C Tip Selection Char ts For use with G40 RA C Housing * Tips are tested in w ater . ✖ P attern width measured withou t airflow . L TX Rever s e-A-Clean (RA C) Spray Tips • L TX R A C spray tips include a metal fluid se at and r ubber fluid seal. • G40 RA C conv ersion kits are av ...

  • Graco Series B - page 33

    LTX Series RAC Tip Selection Charts 311052H 33 RA C Switch Tips FFT Fine Finish RA C Spray Tips WRX Wide RA C Spray Tips * Tips are tested in water . ❖ Measured with NO airflow . Air assist will tend to reduce patte r n lengths by 1 in. to 2 in. Order desired ti p (P ar t No . FFTxxx) wh ere xxx is the size code f or the char t. Orifice Size in. ...

  • Graco Series B - page 34

    Accessories 34 311052H Accessories Gun Manif olds Orde r separately; not i ncluded with gun (See Par t s , page 25) P ar t No. 28821 7 Nor th America Manifold with side fluid ports P ar t No. 28821 8 International Manif old with side fluid por ts P ar t No. 28822 1 Manif old with bottom fl uid por ts P ar t No. 28822 4 High Pressure Air Assisted Ma ...

  • Graco Series B - page 35

    Accessories 311052H 35 Air Cap Seal Kit 253032 P ack of fiv e seals and fiv e o-r ings f or the air cap assembly . Plastic Seat Repair Kit 249424 Kit includes r eplacement plastic seat (pack of ten ), and seat nut. SST Seat Repair Kit 287962 Kit includes assemb led diffuser with SST seat (15H2 82) f or use with pigmented acid catalyz ed materials. ...

  • Graco Series B - page 36

    Dimensions 36 311052H Dimensions F IG . 24 2.0 in. (50.8 mm) 3.86 in. (98.0 m) 3.0 in. (76.2 mm) 4.9 in. (124 .5 mm) TI8113a TI8127a 1.375 in. (34.9 mm) 2.0 in. (50.8 mm) 2.40 in. (60.96 mm) ...

  • Graco Series B - page 37

    Mounting Hole Layout 311052H 37 Mounting Hole La y out F IG . 25: TI8107a 0.4 in. (10.2 mm) (6.3 mm) h oles 0.805 in. (2 0.5 mm) 0.187 in. (4 .8 mm) 1.375 in. (35 mm) 2.125 in. (54 mm) TI8127a 1.750 in. (44.5 mm) Two M5 x 0.8 x 0.25 in. Two 0.128 dia meter x 0.31 in. (7.8 mm) deep holes (for alignment pin) Remove set screws when using bottom mounti ...

  • Graco Series B - page 38

    Mounting Hole Layout 38 311052H Mounting Hole La y out F IG . 26: Mounting Hole La youts TI8227a Rear Port Manifold Retrofit Adapter Plate Gun with Retrofit Adapter Plate TI8178a 2.007 in. (50.98 mm) 1.375 in. (34.93 mm) 0.736 in. (18.69 mm) 2.250 in. (57.15 mm) Gun with Rea r Port Manifold 1.765 in. (44.83 mm ) 2.325 in. (59.06 mm) 2.400 i n. (60. ...

  • Graco Series B - page 39

    Technical Data 311052H 39 Te c h n i c a l D a t a T riggering Speed These v alues apply to a new gun with a 6 ft . (1.8 m), 1/4 in. (6.3 mm) OD cylinder air line and a 0.019 in . tip. These v a lues will vary slightly with use and with variations in equipment. Sound Data (dBa) † Sound pressure me asured 3.28 fe et (1 meter) from equipment. ‡ S ...

  • Graco Series B - page 40

    All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. Original instructions. T his manual contains English. MM 311052 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Kore ...

Manufacturer Graco Category Paint Sprayer

Documents that we receive from a manufacturer of a Graco Series B can be divided into several groups. They are, among others:
- Graco technical drawings
- Series B manuals
- Graco product data sheets
- information booklets
- or energy labels Graco Series B
All of them are important, but the most important information from the point of view of use of the device are in the user manual Graco Series B.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Graco Series B, service manual, brief instructions and user manuals Graco Series B. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Graco Series B.

Similar manuals

A complete manual for the device Graco Series B, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Graco Series B by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Graco Series B.

A complete Graco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Graco Series B - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Graco Series B, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Graco Series B, that we can find in the current document
3. Tips how to use the basic functions of the device Graco Series B - which should help us in our first steps of using Graco Series B
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Graco Series B
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Graco Series B in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Graco Series B?

Use the form below

If you did not solve your problem by using a manual Graco Series B, ask a question using the form below. If a user had a similar problem with Graco Series B it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)