English dropdown-ico

Manual TP-Link Archer D5

127 pages Not applicable
Download

Go to site of 127

Summary
  • TP-Link Archer D5 - page 1

    Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router Rev: 1.0.0 1910011021 ...

  • TP-Link Archer D5 - page 2

    COPYRIGHT & TRADEMARKS Specifications are subjec t to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., L TD. Other brands and product names are trademarks or registered trademarks of t heir respective holders. No part of the specific ations may be reproduced in any form or by any means or used to m ake any derivativ ...

  • TP-Link Archer D5 - page 3

    FCC STATEMENT This equipment has been tested and found to comply wi th the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gen erates, uses and can radiate radio frequency energy and, if no ...

  • TP-Link Archer D5 - page 4

    This is a class B product. In a domestic environmen t, this product may cause radio interference, in which case the user may be required to take adequate measure s. National Restrictions This device is intended for home and office use in all EU countries (and ot her countries following the EU directive 1999/5/EC) wit hout any limitation except for ...

  • TP-Link Archer D5 - page 5

    Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interfer ence-causing equipment regulations. Cet appareil numér ...

  • TP-Link Archer D5 - page 6

    Safety Information  When product has power button, the powe r button is one of the way to shut off the product; when there is no power button, the only way to co mpletely shut off power is to disconnect the product or the power adapter from the power source.  Don’t disassemble the product, or make repairs yourself. You run the ri sk of elec ...

  • TP-Link Archer D5 - page 7

    TP-LINK TECHNOLOGIES CO., L TD TP-LINK TECHNOLOGIES CO., L TD Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China DECLARA TION OF CONFORMITY For the following equipment: Product Description: AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router Model No.: Archer D5 T rademar ...

  • TP-Link Archer D5 - page 8

    CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Product Overview ................................................................................... 2 1.1 Overview of the Modem Router .......................................................................... ...

  • TP-Link Archer D5 - page 9

    4.7.2 Clients List .......................................................................................................................... 41 4.7.3 Address Reservation .......................................................................................................... 41 4.7.4 Conditional Pool .............................................. ...

  • TP-Link Archer D5 - page 10

    4.13.1 IPv6 Default Gateway ....................................................................................................... 77 4.13.2 IPv6 Static Route .............................................................................................................. 78 4.14 Forwarding ............................................................ ...

  • TP-Link Archer D5 - page 11

    4.24 Logout ......................................................................................................................... 111 Appendix A: Specifications ................................................................................. 112 Appendix B: Troubleshooting ....................................................................... ...

  • TP-Link Archer D5 - page 12

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 1 Package Content s The following contents should be found in your package:  One Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router  One Power Adapter for Archer D5 A C1200 Wireless Dual Band Gigabit ADSL2+ Mo dem Router  Quick Installation Guide  O ...

  • TP-Link Archer D5 - page 13

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 2 Chapter 1. Product Overview Thank you for choosing the Archer D5 AC1200 Wireless Du al Ba nd Gigabit ADSL2+ Modem Router . 1.1 Overview of the Modem Router The Archer D5 AC1200 Wireless Dual Band Gig abit ADSL2+ Modem Router integrates 4-port Switch, Firewall, NAT-Router ...

  • TP-Link Archer D5 - page 14

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 3 1.2 Main Features  Complies with IEEE 802.11ac to provide a wire less data rate of up to 30 0 Mb p s ( 2. 4 GH z) + 867Mbps (5GHz).  Four 10/100/1000Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), one RJ11 port.  Provides external splitter.  Adopts Advan ...

  • TP-Link Archer D5 - page 15

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 4 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The modem router’s LEDs are lo cated on the top panel (View from top to bottom). They indicate the device’s working stat us. For details, please re fer to LED Explanation. LED Explanation: Name Status Indication On A w ...

  • TP-Link Archer D5 - page 16

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 5 On There is a device connected to this LAN port, or the LAN port is sending or receiving data. (LAN) Off There is no device connected to this LAN port. On Wireless is enabled. The modem r outer is working on 2.4GHz/5 GHz radio band. (Wireless) Off Wireless is disabled. On ...

  • TP-Link Archer D5 - page 17

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 6 1.3.2 The Back Panel Figure 1-2  ADSL : Through the port, you can connect the tel ephone to the modem router. Or you can connect them by an external separate sp litter. For details, please refer to 2.3 Connecting the Modem Router .  USB2, USB1 : The USB port connect ...

  • TP-Link Archer D5 - page 18

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 7 Chapter 2. Connecting the Modem Router 2.1 System Requirement s  Broadband Internet Access Service (DSL/Cable/Ethernet).  PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors.  TCP/IP protocol on each PC.  Web browser, such as Micr os ...

  • TP-Link Archer D5 - page 19

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 8 Figure 2-1 ...

  • TP-Link Archer D5 - page 20

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 9 Chapter 3. Quick Inst allation Guide This chapter will show you how to configure the basic functi ons of your Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the Ar ...

  • TP-Link Archer D5 - page 21

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 10 The LEDs of LAN port which you link to the device and the LEDs on y our PC's adapter should be lit. 2) Is the TCP/IP configuration for y our PC correct? If the modem router's IP addre ss is 192.168.1.1, your PC's IP address must be within the range of 192. ...

  • TP-Link Archer D5 - page 22

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 11  Note: 1) Do not mix up the user na me and password with your ADSL account user name and password which are needed for PPP connections. 2) If the above screen does not pop up, it means that your Web-br owser has been set to a proxy. Go to Tools menu → Internet Optio ...

  • TP-Link Archer D5 - page 23

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 12 5. Select Yes and wait for 1-2 minutes to detect the connection type. Figure 3-6  Note: If the connection type can not be detected, please select No… and click Next to configure it manually (shown in Figure 3-7 ). Figure 3-7 A. Configuration for PPPoE/PPPoA Enter th ...

  • TP-Link Archer D5 - page 24

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 13  Note: If you are using the modem router on a new DSL li ne and have not completed your DSL provider ’s online registration, you may be using a generic username and pa ssword. When registration is completed, you will need to update the username and password if you h ...

  • TP-Link Archer D5 - page 25

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 14 Figure 3-11 8. On this page, please confirm all parameters. Click Back to modify or click the Save button to save your configuration. Figure 3-12 9. You will see the Complete screen below, click Finish to complete these settings. ...

  • TP-Link Archer D5 - page 26

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 15 Figure 3-13 The basic settings for your modem router are co mpleted. Please open the web browser and try to log on to http://www.tp-link.com to test your Internet connection. ...

  • TP-Link Archer D5 - page 27

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 16 Chapter 4. Configuring the Modem Router This chapter will show confi guration for the key functions on the Web-based management page. 4.1 Login After your successful login, you will see the twent y-three main menus on the left of the Web-based utility. On the right, ther ...

  • TP-Link Archer D5 - page 28

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 17 4.2 S t atus Choose “ Status ”, you can see the corre sponding information about Device Information , DSL , WAN , LAN and Wireless . ...

  • TP-Link Archer D5 - page 29

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 18 Figure 4-1 ...

  • TP-Link Archer D5 - page 30

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 19 4.3 Quick Setup Please refer to 3.2 Quick Installation Guide . 4.4 Operation Mode Choose “ Operation Mode ”, and you will see the screen as shown in Figure 4-2 . Select your desired mode and then click Save . Figure 4-2  DSL Modem Router Mode: The device enables m ...

  • TP-Link Archer D5 - page 31

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 20 4.5.1 WAN Settings Choose “ Netw ork ”  “ WAN Settings ”, and you will see the WAN Port Information Table in the screen similar to Figure 4-3 . There are six different configurat ions for the connection types, which are Static IP, Dynamic IP, P PPoE, PPPoA, IP ...

  • TP-Link Archer D5 - page 32

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 21 Figure 4-4 4.5.1.1 Static IP Select this option if your ISP prov ides static IP information to yo u. You should set static IP address, IP subnet mask, and gateway address in the screen below. ...

  • TP-Link Archer D5 - page 33

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 22 Figure 4-5 ATM Configuration:  VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid r ange is from 0 to 255. Please input the value provided by your ISP.  VCI (1~65535): Identifies the virtual channel endpoints in an ATM network. ...

  • TP-Link Archer D5 - page 34

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 23  Gateway (Optional): Enter the gateway IP addres s in dotted-decimal notation provided by your ISP.  DNS Server/ Secondar y DNS Server: Here you can set DNS Server (at leas t one) manually. The modem router will use the fi rst DNS Server for priority.  Default G ...

  • TP-Link Archer D5 - page 35

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 24 Figure 4-6 Click Advance , advanced selections for WAN Service Setup can be shown.  MTU (bytes): . The default MTU (Maximum Transmission Unit) value is 1500 Bytes. Do not change the default value unle ss required by your ISP.  Enable NAT: This technology translates ...

  • TP-Link Archer D5 - page 36

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 25  Get IP w ith Unicast: It is disabled b y default. A few ISPs’ DHCP Servers do not support the broadcast applications. When t he modem router cannot get the IP address normally, you can choose this option. (It is rarely required)  Set DNS Server manually: Choose ...

  • TP-Link Archer D5 - page 37

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 26 Figure 4-7  PPP Username/Password/Confirm Passw ord : Enter the User Name, Password and Confirm Password provided by your ISP. These fields are case-sensitive.  Alw ays on: The connection can be re-e stablished automatically when it is down.  Connect on demand: ...

  • TP-Link Archer D5 - page 38

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 27  Enable IPv6: Check this box to enable IPv6.  Default Gatew ay: Select a WAN connection from the dr op-down list as the IPv4 default gateway.  IPv6 Default Gatewa y: Select a WAN connection from the dr op-down list as the IPv6 default gateway. Click Advance , ad ...

  • TP-Link Archer D5 - page 39

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 28 Figure 4-8 4.5.1.5 IPoA If your ISP provides an IPoA connection, select IPoA option for the Connection Type on the screen. ...

  • TP-Link Archer D5 - page 40

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 29 Figure 4-9  IP Address/Subnet Mask: Enter the IP Address and Subnet Mask provided by ISP.  DNS Server/Secondar y DNS Server: Type in your preferred DNS server.  Default Gatew ay: Select a WAN Interface from the drop-down list as the IPv4 default gateway. 4.5.1.6 ...

  • TP-Link Archer D5 - page 41

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 30  Note: After you finish the Internet configuration, please click Save to m ake the settings take e ffe ct. 4.5.2 Interface Grouping Choose “ Network ”  “ Interface Grouping ”, you can view all the current groups on this page (shown in Figure 4-11 ). Figure ...

  • TP-Link Archer D5 - page 42

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 31 Figure 4-12 Click Save to make the entry effective immediately 4.5.3 LAN Settings Choose “ Network ”  “ LAN Settings ” menu, and you will see the LAN screen (shown in Figure 4-13 ). Please configure the param ete rs for LAN ports according to the descriptions ...

  • TP-Link Archer D5 - page 43

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 32  Enable IGMP Snooping: IGMP Snooping is the process of listening to IGMP (Internet Group Management Protocol) network traffic. The feature prevents hosts on a local network from receiving traffic for a multicast group they have not explicitly joined. It is enabled by ...

  • TP-Link Archer D5 - page 44

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 33 2) If DHCPv6 Server is selected, please complete the following parameters. Figure 4-15  Start IPv6 Address: Enter a value for the DHCPv6 server to start with when issuing IPv6 addresses.  End IPv6 Address: Enter a value for the DHCPv6 server to end with when issuin ...

  • TP-Link Archer D5 - page 45

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 34 4.5.5 MAC Clone Choose menu “ Netw ork ”  “ MAC Clone ”, you can configure t he MAC address of the W AN Interface as shown below . The W AN Interface List displays the W AN Interfaces you have c onfigured on the section 4.5.1 W AN Settings and its default MAC ...

  • TP-Link Archer D5 - page 46

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 35  L2TP Pass-through: L2TP (Layer Two Tunneling Pr otocol) is the method used to enable Point-to-Point sessions via the Inter net on the Layer Two level. To allow L2TP tunnels to pass through the modem router, click Enable .  IPSec Pass-through: IPSec (Internet Proto ...

  • TP-Link Archer D5 - page 47

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 36 Figure 4-21 This section will guide you to configure a VPN tun nel between two Archer D5s. The topology is as follows. Archer D 5 Archer D 5  Note: You could also use other VPN Rout ers to set VPN tunnels with Archer D5 . Archer D5 suppor ts up to 10 VPN tunnels simul ...

  • TP-Link Archer D5 - page 48

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 37 Figure 4-22  IPSec Connection Name: Enter a name for your VPN.  Remote IPSec Gatew ay Address (URL): Enter the destination gatew ay IP address which is the public WAN IP or Domain Name of the re mote VPN server endpoint. (For example: Input 219.134.112.247 in Devic ...

  • TP-Link Archer D5 - page 49

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 38 Click Show Advanced Settings and then you can configure the Advanced Settings. We recommend you leave the Advanced Settings as default value. Figure 4-23  Mode: Select Main Mode to con figure the standard negotiation parameters for IKE phase1.Select Aggressive Mode to ...

  • TP-Link Archer D5 - page 50

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 39 Figure 4-24  Enable IPTV: Check the box to enable IPTV function.  VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid r ange is from 0 to 255. Please input the value provided by your ISP.  VCI (1~65535): Identifies the virtual ...

  • TP-Link Archer D5 - page 51

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 40 Figure 4-25  Group/ IP Address/ Subnet Mask: Displays group name, IP address and subnet mask. The parameters can be configured on the Interface Groupi ng page and LAN Settings page.  DHCP Server: If enabled, the modem router will work as a DHCP server, which provid ...

  • TP-Link Archer D5 - page 52

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 41  Note: 1) To use the DHCP server func tion of the modem router, you mu st configure all computers on the LAN as "Obtain an IP Address automatically". 2) Y ou have to disable NA T of the WAN connections, or the DHCP Relay may not ta ke effect. 3) If you selec ...

  • TP-Link Archer D5 - page 53

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 42 Figure 4-27  MAC Address: The MAC address of the PC for which you want to reserve an IP address.  IP Address: The IP address reserved for the PC by the modem router.  Status: The status of this entry, either Enabled or Disabled . To Reserve an IP address: 1. Cli ...

  • TP-Link Archer D5 - page 54

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 43 Figure 4-29 To add a vendor class: 1. Click the Add New button. Then Figure 4-30 will pop up. 2. Enter parameters for the vendor class. Click the Save button. Figure 4-30 To modify or delete an existing entry: 1. Click Edit in the entry you want to modify the entry. 2. M ...

  • TP-Link Archer D5 - page 55

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 44 4.8 Wireless 2.4GHz There are seven subme nus under the Wireless 2.4Ghz menu: Basic Setti ngs , WPS Settings , Wireless Security , Wireless Schedule , Wireless MAC Filtering , Wireless Advanced and Wireless Status . Click any of them, and you will be able to configure th ...

  • TP-Link Archer D5 - page 56

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 45 11g only: Select if all of your wireless clients are 802.11g. 11n only: Select only if all of your wireless clients are 802.11n. 11bg mixed: Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed: Select if you are using a mix of 802.11b, 11g, and ...

  • TP-Link Archer D5 - page 57

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 46  Authentication T ype : This option should be chosen if the key type is WEP(ASCII) or WEP(HEX). It indicates the author ization type of the Root AP.  Passwo rd : If the AP your modem router is going to connect needs password, you need to fill the password in this b ...

  • TP-Link Archer D5 - page 58

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 47 You can also keep the default WPS Status as Enabled and click the Add device button in Figure 4-32 , then Choose “ Press the button of the ne w device in two minutes ” and click Connect . (Shown in the following figure) Figure 4-33 Step 2: Press and hold the WPS butt ...

  • TP-Link Archer D5 - page 59

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 48 Setup process. Step 3: When the WPS LED is on, the client devic e has successfully connected to the modem router. Step 4: Refer back to your client device or its documentation for further instructions.  Note: 1) The WPS LED on the modem r outer will light green for fi ...

  • TP-Link Archer D5 - page 60

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 49  Encryption: You can select Auto , TKIP or AES as Encryption.  Wireless Password: You can enter ASCII characters bet ween 8 and 63 characters or 8 to 64 Hexadecimal characters. The default password is the same with the def ault PIN code, which is labeled on the bot ...

  • TP-Link Archer D5 - page 61

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 50 Be sur 4.8.4 configur e the T ask Schedule  Key Type: You can select the WEP key length (64-bit, or 128-bit.) for encryption. "Disabled" means this WEP key entry is invalid. 64-bit: You can enter 10 hexadecimal di gits (any combination of 0-9, a-f, A-F, zero ...

  • TP-Link Archer D5 - page 62

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 51 ” Wireless MAC Filtering ”, you can control the wireless 4.8.5 Wireless MAC Filtering Choose menu “ Wireless 2.4GHz ”  access by configuring the Wireless MAC Filtering function, shown in Figure 4-37 . Figure 4-37 To filter wireless users by MAC Address, cl he ...

  • TP-Link Archer D5 - page 63

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 52 nt to modify. Selected button to make selected entries enabled or disabled. ess 00:1 D:0 F:1 1:2 2:3 3 and the cified by any enabled entries in the list to if there are any entries already. 0:1D:0F:11:22:33 / 00:0A:EB:00:07:5F in the MAC Address field. d s hould be simil ...

  • TP-Link Archer D5 - page 64

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 53 Figure 4-39  Transmit Power: Here you can specify the transmit power of the modem router. You can select 100%, 50% or 25%. 100% is the default setting and is recommended.  Beacon Interval: Enter a value between 25- 1000 milliseconds for Beac on Interval here. The b ...

  • TP-Link Archer D5 - page 65

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 54 4.8.7 Wireless Status Choose menu “ Wireless 2.4GHz ”  ” Wireless Status ”, you can see the MA C Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 4-40  MAC Address: The connected wireless station's ...

  • TP-Link Archer D5 - page 66

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 55 Figure 4-41  SSID: Wireless network name. Enter a desired SSI D which is case-sensitive and must not exceed 32 characters. The def ault SSID is TP-LINK_5GHz_ XXXXXX (xx is the last six numbers of MAC address) .  Region: Select your region from the drop-down list. T ...

  • TP-Link Archer D5 - page 67

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 56  SSID (to be bridged): The SSID of the AP your modem ro uter is going to connect to as a client. You can also use the search f unction to select the SSID to join.  BSSID (to be bridged): The BSSID of the AP your modem r outer is going to connect to as a client. You ...

  • TP-Link Archer D5 - page 68

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 57 button. b). To add a new device: If the wireless adapter supports Wi-Fi Protected Setup (WPS ), you can establish a wireless connection between wireless adapter and modem router using either Push Button Configuration (PBC) method or PIN method.  Note: To build a succe ...

  • TP-Link Archer D5 - page 69

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 58 Figure 4-44 Step 2: Enter the PIN number from the client devic e in the field on the above WPS screen. Then click Connect button. Step 3: “ Connect successfull y ” will appear on the screen of Figure 4-44 , which means the client device has successfully connected to ...

  • TP-Link Archer D5 - page 70

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 59 Figure 4-45  Disable Wireless Securit y: If you do not want to use wire less security, check this radio button. But it’s strongly reco mmended to choose one of the below modes to ensure security.  WPA/WPA2-Personal - It’s the WPA/WPA2 authenticat ion type based ...

  • TP-Link Archer D5 - page 71

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 60  Authentication Type : Authentication Type: You can choose the type for the WPA/WPA2-Personal security on the drop-down list. The default setting is Auto , which can select WPA-PSK or WPA2-PSK as authentication type automatic ally based on the wireless station's ...

  • TP-Link Archer D5 - page 72

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 61 Be sur 4.9.4 nfigure the T ask Schedule as e to cli ck the Save button to save your settings on this page. Wireless Schedule Choose menu “ Wireless 5GHz ”  “ Wireless Schedule ”, you can co shown below . Figure 4-46  Note: The time you set is the peri od yo ...

  • TP-Link Archer D5 - page 73

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 62 Figure 4-47 To filter wireless users by MAC Address, clic k Enable . The default setting is Disabled .  MAC Address: The wireless station's MAC address that you want to filter.  Status: The status of this entry either Enabled or Disabled .  Host: The wirele ...

  • TP-Link Archer D5 - page 74

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 63 3. Click the Save button. Click the Enable/ Disabled Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete the selected entries. For example: If you desire that th e wireless station A with MAC addre ss 00: 1D: 0F: 11: 2 ...

  • TP-Link Archer D5 - page 75

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 64 Figure 4-49  Transmit Power: Here you can specify the transmit power of the modem router. You can select 100%, 50% or 25%. 100% is the default setting and is recommended.  Beacon Interval: Enter a value between 25- 1000 milliseconds for Beac on Interval here. The b ...

  • TP-Link Archer D5 - page 76

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 65 Figure 4-50  MAC Address: The connected wireless station's MAC address  Current Status: The connected wireless stati on's running status, one of STA-A UTH/ ST A-AS S O C/ ST A-JO I N E D/ W P A/ W P A- P S K/ W P A2 / W P A2 - PS K / AP - U P/ AP -D O W N ...

  • TP-Link Archer D5 - page 77

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 66 Figure 4-51  Guest Network: When enable this function, you c an set wireless parameters for guest network.  SSID: The guest network name. When setting up a Guest network, it is strongly recommended to use a name that easily disti nguishes it from your primary netwo ...

  • TP-Link Archer D5 - page 78

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 67 Figure 4-52  Guest Network: When enable this function, you c an set wireless parameters for guest network.  SSID: The guest network name. When setting up a Guest network, it is strongly recommended to use a name that easily disti nguishes it from your primary netwo ...

  • TP-Link Archer D5 - page 79

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 68 4.10.3 Guest Status 2.4GHz Choose menu “ Guest Network ”  “ Guest Status 2.4GHz ”, you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 4-53  MAC Address: The connected wireless station&a ...

  • TP-Link Archer D5 - page 80

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 69 4.11 USB Settings There are six submenus under the USB Settings menu, USB Mass Storage , User Accounts , Storage Sharing , FTP Server , Media Server and Print Server . Click any of them, and you will be able to configure the corresponding function. 4.11.1 USB Mass Storag ...

  • TP-Link Archer D5 - page 81

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 70 when volume is non-shared, you can click the Activate button to share the volume. Click Disconnect to safely remove the USB storage dev ice that is connected to USB port.  Note: Before removing the USB storage device, you should cl ick “Disconnect” to make sure th ...

  • TP-Link Archer D5 - page 82

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 71 Figure 4-57  Server Status: Indicates the Storage Sharing's current status.  Anonymous access to all the volumes: This function is enabled by default, so that users can access to all activated volumes without aut hentication. If you want to add a shared folder ...

  • TP-Link Archer D5 - page 83

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 72 Figure 4-58 2. Click the Brow se button, and then select the Sele ct Volume from the drop-down list. 3. Enter the display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings. You can click the upper button to go to the upper fold ...

  • TP-Link Archer D5 - page 84

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 73 Figure 4-59  Server Status: Indicates the FTP Server's current status.  Internet Access: If Internet Access is enabled, user(s) in public network can access FTP server via Internet Address.  Internet Address: If Internet Access is enabled, WAN IP will be di ...

  • TP-Link Archer D5 - page 85

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 74 Figure 4-60 2. Click the Brow se button, and then select the Sele ct Volume from the drop-down list. 3. Enter display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder. ...

  • TP-Link Archer D5 - page 86

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 75 b) Enter the name of the share folder in Share Name field. c) Click the Apply button to apply the configuration. Figure 4-62 Click the Scan now to scan all the share folders imm ediately. You can also select the Auto-scan , and, at the same time, select an auto scan inte ...

  • TP-Link Archer D5 - page 87

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 76 4.12.1 Default Gate way Choose “ Route Settings ”  “ Default Gatewa y ”, you can see the Default Gateway screen. You can select a WAN Interface from the drop-down list as the system default gateway. Figure 4-64 Click the Add Interface button, you can add WAN I ...

  • TP-Link Archer D5 - page 88

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 77 static route.  Subnet Mask: It determines which portion of an IP Address is the network portion, an d which portion is the host portion.  Gateway: Type in the correct gateway addr ess for the static route.  Interface: Select the Interface from the drop-down list ...

  • TP-Link Archer D5 - page 89

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 78 Figure 4-68 Click the Add Interface button, you can add WAN Interfaces. Click the Save button to save your settings. 4.13.2 IPv6 Static Route Choose “ IPv6 Route Settings ”  “ IPv6 Static Route ”. You can see the IPv6 Static Route screen. This screen allows yo ...

  • TP-Link Archer D5 - page 90

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 79  Prefix Length: The prefix length of the destination IPv6 address.  Gateway: Type in the correct IPv6 Gateway addr ess for the IPv6 Static Route.  Interface: Select the Interface from the drop-down list.  Status: Select Enabled or Disabled from the drop-down ...

  • TP-Link Archer D5 - page 91

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 80  IP Address : The IP address of the PC running the service application.  Protocol : The protocol used for this application. The options are TCP , UDP , or All (all protocols supported by the modem router).  Statu s : The status of this entry , "Enabled" ...

  • TP-Link Archer D5 - page 92

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 81 System Tools –> Manage Control page to be any other value except 80 such as 8080. Otherwise there will be a conflict to disable the virtual server. 4.14.2 Port Triggering Choose menu “ Forwarding ” → ” Port Triggering ”, you can view and add port triggerin ...

  • TP-Link Archer D5 - page 93

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 82 Figure 4-74  Interface : Display the default gateway you have set in 4.5.1 WAN Settings .  Trigger Port : The port for outgoing traffic. An outgoing connection using this port will trigger this rule.  Trigger Protocol : The protocol used for Trigger Ports. The o ...

  • TP-Link Archer D5 - page 94

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 83  Note: 1. When the trigger connecti on is released, the correspondi ng opened ports will be closed. 2. Each rule can only be used by on e host on the LAN at a time. The tr igger connection of other hosts on the LAN will be refused. 3. Open Ports ranges cannot overlap ...

  • TP-Link Archer D5 - page 95

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 84  Current UPnP Status: UPnP can be enabled or di sabled by clicking the Enable or Disable button. This feature is enabled by default.  Current UPnP Settings List: This table displays the current UPnP information.  App Description : The description about the appli ...

  • TP-Link Archer D5 - page 96

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 85 Figure 4-77  Enable Parental Control: Check the box if you want this func tion to take effect. This function is disabled by default.  MAC Address of Parental PC: In this field, enter the MAC address of the controlling PC, or you can make use of the Copy To Above bu ...

  • TP-Link Archer D5 - page 97

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 86 4.16 Firewall There are four submenus under the Fi rewall menu: Rule , LAN Host , WAN Host and Schedule . Click any of them, and you will be able to configure the corre sponding function. 4.16.1 Rule Choose menu “ Firewall ” → “ Rule ”, and then you can view an ...

  • TP-Link Archer D5 - page 98

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 87 The methods to add a new rule: 1. Click the Add New button and the next screen will pop up as shown in Figure 4-79 . 2. Give a name (e.g. Rule_1) for the rule in the Description field. 3. Select a host from the LAN Host drop-down list or choose “ Add LAN Host ”. 4. S ...

  • TP-Link Archer D5 - page 99

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 88  Edit: To modify an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New button. 2. In the Mode field, select IP Address or MAC Address.  If you select IP Address, please follow the steps below: 1) In Description field, create a u ...

  • TP-Link Archer D5 - page 100

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 89 1) In Description field, create a unique description for the host (e.g. Host_1). 2) In IP Address field, enter the IP address. If you select MAC Address , the screen shown is Figure 4-83 . Figure 4-83 1) In Description field, create a unique description for the host (e.g ...

  • TP-Link Archer D5 - page 101

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 90 Figure 4-85  Description : Here displays the description of the sc hedule and this description is unique.  Edit : Here you can modify an existing schedule. To add a new schedule, follo w the steps belo w : 1. Click Add New button and the next screen will pop-up as ...

  • TP-Link Archer D5 - page 102

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 91 4.17 IPv6 Firewall There are four submenus unde r the I Pv6 Firewall menu: IPv6 Rule , IPv6 LAN Host , IPv6 WAN Host and IPv6 Schedule . Click any of them, and you will be able to configure the corresponding function. 4.17.1 IPv6 Rule Choose menu “ IPv6 Firewall ” ? ...

  • TP-Link Archer D5 - page 103

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 92 Figure 4-88 2. Give a name (e.g. Rule_1) for the rule in the Descri ption field. 3. Select a host from the IPv6 LAN Host drop-down list or choose “ Add IPv6 LAN Host ”. 4. Select a host from the IPv6 WAN Host drop-sow n list or choose “ Add IPv6 WAN Host ”. 5. Se ...

  • TP-Link Archer D5 - page 104

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 93  Edit: To modify an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New button, and you will see the screen as shown in Figure 4-90 . Figure 4-90 2. Create a unique name fo r the host (e.g. Host_1) in the Description field. 3. Enter ...

  • TP-Link Archer D5 - page 105

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 94 Figure 4-92 2. Create a unique description for the host (e.g. Host_1) in the Description field. 3. Enter an IPv6 address in the IPv6 Address field. 4. Enter the prefix length of the IPv6 address in the Prefix Length field. 5. Click the Save button to save the settings. C ...

  • TP-Link Archer D5 - page 106

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 95 Figure 4-94 2. Create a unique description for the schedule ( e.g. Schedule_1) in Description field. 3. Select the day or days you need in Appl y To field. 4. In time field, you can select all day-24 hours or you may enter the Start Time and Stop Time in the correspondin ...

  • TP-Link Archer D5 - page 107

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 96 Figure 4-95  Enable: Check the box to enable IPv6 Tunnel function. It is disabled by default.  Mechanism: Select a type for IPv6 tunnel from th e drop-down list. DS-Lite, 6RD and 6to4 are supported. 1) DS-Lite This type is used in the situati on that your WAN conne ...

  • TP-Link Archer D5 - page 108

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 97 Figure 4-97  WAN Connection: Select a WAN connection from the drop -down list. Only the connected WAN connections can be shown in the drop-down list.  Configuration Type: Select a configuration type for th is tunnel. Auto means to ob tain the following parameters a ...

  • TP-Link Archer D5 - page 109

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 98 4.19 Bandwid th Control Choose menu “ Bandwidth Control ”, and then you can configure the Upstream Bandwidth and Downstream Bandwidth in the next screen. T he values you configur e should be less than 1000000Kbps. For optimal control of the band width, please select ...

  • TP-Link Archer D5 - page 110

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 99 Figure 4-100 3. Click the Save button. Click the Enable/ Disable Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete the selected entries. 4.20 IP&MAC Binding There are two submenus under the IP &MAC Binding me ...

  • TP-Link Archer D5 - page 111

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 100 When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Edit button, and then you will go to the next page. Th is page is used for adding or modifying an IP & MAC Binding entry (shown in Figure 4-102 .) Figure 4-102 To add I ...

  • TP-Link Archer D5 - page 112

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 101 Click the Delete Selected button to delete the selected entries. Click the Refresh button to refresh all items. 4.21 Dynamic DNS Choose menu “ Dynamic DNS ”, and you can configure t he Dynamic DNS function. The modem router offers the DDNS (Dynamic Domain Name Syste ...

  • TP-Link Archer D5 - page 113

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 102 Figure 4-105 4.23 System T ools Choose menu “ System Tools ”, and you can see the s ubmenus under the main menu: System Log , Time Settings , Manage Control , CWMP Settings , SNMP Settings , Backup & Restore , Factory Defaults , Firmware Upgrade , Reboot and Sta ...

  • TP-Link Archer D5 - page 114

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 103 Figure 4-106  Log Type: Select the log type to be displayed.  Log Level: Select the log level to be displayed.  Refresh: Refresh the page to show the latest log list.  Clear Log: All the logs will be deleted from the modem router permanently, not just from t ...

  • TP-Link Archer D5 - page 115

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 104 Figure 4-108  Time Zone: Select your local time zone from this drop-down list.  Date: Enter your local date in MM/DD/YY into the right blanks.  Time: Enter your local time in HH/ MM/SS into the right blanks.  NTP Server 1 / NTP Server 2: Enter the address or ...

  • TP-Link Archer D5 - page 116

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 105 Figure 4-109  Current User Status: Thi s box displays the information about User Ty pe , User Name , Host IP Address and Host MAC Address .  Account Management: Here you can set the account user information a bout New User Name and Ne w Pa s s wo r d .  Service ...

  • TP-Link Archer D5 - page 117

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 106 Figure 4-110  CWMP: Select Enable to enable the CWMP function.  Inform: If enabled, the information will be in formed to ACS server periodically.  Inform Interval: Enter the interval time here.  ACS URL: Enter the website of ACS whic h is provided by your IS ...

  • TP-Link Archer D5 - page 118

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 107 Figure 4-111 An SNMP Agent is an application running on the modem rout er that performs the operational role of receiving and processing SNMP messages, sending responses to the SNMP manager, and sending traps when an event occurs. So a rout er contains SNMP "agent& ...

  • TP-Link Archer D5 - page 119

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 108 Figure 4-113 Click the Restore button to reset all configuration settings to their default values.  The default User Name : admin  The default Pass w ord : admin  The default Subnet Mask : 255.255.255.0  Note: All changed settings will be lost when factory d ...

  • TP-Link Archer D5 - page 120

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 109 want to use. 2) When u pgrade the modem router's firmware, yo u may lose its current configurations, so please write down some of your customized settings before upgrading the firmware. 3) Do not turn off the modem router or pre ss the Reset button while the firmwa ...

  • TP-Link Archer D5 - page 121

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 110 Figure 4-116  Traffic Status: If it is disabled, the f unction of DoS protection in Security settings will be disabled.The default value is di sabled. To enable it, click the Enable .  Statistics Interval (5-60): Indicates the time section of the packets statistic ...

  • TP-Link Archer D5 - page 122

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 111 Reset Reset the value of the entry to zero. Operation Delete Delete the existing entry in the table. 4.24 Logout Choose “ Logout ”, and you will back to the login screen as shown in Figure 4-117 . Figure 4-117 ...

  • TP-Link Archer D5 - page 123

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 112 Appendix A: Sp ecifications General Standards and Protocols ANSI T1.413, ITU G.992.1, ITU G.992.3, ITU G.992.5, IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.11ac, IEEE 802.3, IEEE 802.3u, IEEE802.3ab, TCP/IP, PPPoA, PPPoE, SNTP, HTTP , DHCP, ICMP, NA ...

  • TP-Link Archer D5 - page 124

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 113 Appendix B: T roubleshooting T1. How do I restore m y modem router’s configuration to its factor y default settings? With the modem router powered on, press and hold the RESET button on the rear pa nel for 8 to 10 seconds before releasing it.  Note : Once the modem ...

  • TP-Link Archer D5 - page 125

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 114 4 ） Select Obtain an IP address automaticall y and Obtain DNS server address automati cally . Then click OK . For Windows 8 1 ） Move your mouse to the lowe r right corner and you will see Search icon in the Popups. Go to “ -> Apps ”. Type Control Panel in the ...

  • TP-Link Archer D5 - page 126

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 115 Now, try to log on to the Web-based configur ation page again after the above settings have been configured. If you still cannot acce ss the configuration page, please restore your modem router’s factory default settings and re configure your modem router following th ...

  • TP-Link Archer D5 - page 127

    Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 116 Appendix C: T echnical Support Technical Support  For more troubleshooting he lp, go to: http://www.tp-link.com/e n/support/faq  T o do wnload the latest Firmware, Driver , Utility and User Guide, go to: http://www .tp-link .com/en/support/do wnload  For all ot ...

Manufacturer TP-Link Category Router

Documents that we receive from a manufacturer of a TP-Link Archer D5 can be divided into several groups. They are, among others:
- TP-Link technical drawings
- Archer D5 manuals
- TP-Link product data sheets
- information booklets
- or energy labels TP-Link Archer D5
All of them are important, but the most important information from the point of view of use of the device are in the user manual TP-Link Archer D5.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals TP-Link Archer D5, service manual, brief instructions and user manuals TP-Link Archer D5. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product TP-Link Archer D5.

Similar manuals

A complete manual for the device TP-Link Archer D5, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use TP-Link Archer D5 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of TP-Link Archer D5.

A complete TP-Link manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual TP-Link Archer D5 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the TP-Link Archer D5, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the TP-Link Archer D5, that we can find in the current document
3. Tips how to use the basic functions of the device TP-Link Archer D5 - which should help us in our first steps of using TP-Link Archer D5
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with TP-Link Archer D5
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of TP-Link Archer D5 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning TP-Link Archer D5?

Use the form below

If you did not solve your problem by using a manual TP-Link Archer D5, ask a question using the form below. If a user had a similar problem with TP-Link Archer D5 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)