English dropdown-ico

Manual Renesas H8/33937

20 pages 0.5 mb
Download

Go to site of 20

Summary
  • Renesas H8/33937 - page 1

    H8/3937R H8/33937 Series TFP-100B User System Interface Cable (HS3937ECH61H) for E6000 Emulator User’s Manual HS3937ECH61HE(B) ...

  • Renesas H8/33937 - page 2

    Cautions 1. Renesas neither warrants nor grants li censes of any rights of Renesas’s or any t hird party’s patent, copyright, t rademark, or other intel lect ual property rights for informat ion contained in this document. Renesas bears no responsibility fo r problem s that may arise with third party’s rights, including int ellectual property ...

  • Renesas H8/33937 - page 3

    i Preface Thank you for purchasing this user system interface cable (HS3937ECH61H) for the Renesas’s original mi crocomputer H8/3937R H8/ 3937 series. The HS3937ECH61H is a user system interface cab le that connects an H8/300L series E6000 emulator (HS388R EPI60H; herei naft er referred t o as the emulat or) through the expansion board to the IC ...

  • Renesas H8/33937 - page 4

    ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting User System Interf ace Cable to Em ulat or Station ......................................... 3 2.2 Connecti ...

  • Renesas H8/33937 - page 5

    Section 1 Configuration CAUTION Use an IC149-100-054-B51 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the TFP-100B package IC socket on the user system. Figure 1 shows the configuration of the HS3937E CH61H user system interface cable for the TFP-100B package. Figure 1 HS3937ECH61H User System Interface Cable 1 ...

  • Renesas H8/33937 - page 6

    2 Table 1 lists t he HS3937ECH61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS3937ECH61H Components No. Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the TFP-100B package 4 Socket cover 1 For installing an TFP-100B packaged MCU 5 Screws (M2.6 x 12 mm) 4 For fasten ...

  • Renesas H8/33937 - page 7

    Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and w ill damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system a ...

  • Renesas H8/33937 - page 8

    2. [1] After maki ng sure the direction of the expansion board connect or labeled E6000 EMULATOR is correct, firm ly insert the expansion board connect or into the emulat or station connector ([1] i n figure 2). [2] Connect the expansion board labeled USER INTER FACE CABLE and the user system interface cable body. 6 0 0 0 US ER I N TER F A C E CA B ...

  • Renesas H8/33937 - page 9

    2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pi n 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the ...

  • Renesas H8/33937 - page 10

    6 2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an TFP-100B package on the user system wi th pin 1 on the user system interface cable head, and inse rt the user system interface cable head into the IC socket on the user system, as shown i n figure 3. 2.2.4 Fastening Cable Head CAUT ...

  • Renesas H8/33937 - page 11

    Fasten the user system interface cable head to the IC socket fo r an TFP-100B package on the user system wit h the four screws (M2.6 x 12 mm ; with flat washers) provi ded. Each screw should be tightened a little at a time, alternating between scre ws on opposing corners. Take special care, such as manually securing the IC socket soldered area, to ...

  • Renesas H8/33937 - page 12

    2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable body Cable head Remove jig Push the remove jig Removing User system Figure 4 Fastening Cable Body 8 ...

  • Renesas H8/33937 - page 13

    2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for an TFP-100B package (IC149-100-054-B51: m anufactured by YAM AICHI ELECTRONICS Co., Ltd.). Note that the dimensions in figure 5 are somewh at different from those of the actual chi ...

  • Renesas H8/33937 - page 14

    2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 6. Figure 6 Dimensions for User System Interface Cable Head 10 ...

  • Renesas H8/33937 - page 15

    2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 7. Figure 7 Resulting Dimensions after Connecting User System Interface Cable 11 ...

  • Renesas H8/33937 - page 16

    12 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes ...

  • Renesas H8/33937 - page 17

    Figure 8 Installing MCU to User System 13 ...

  • Renesas H8/33937 - page 18

    14 Section 4 Verifying Operation 1. When using the H8/300L series E6000 emul ator (HS388REPI60H), turn on the emul ator according to the procedures described in the H8/300L Series E6000 Em ulator User' s Manual (HS388REPI60HE). 2. Verify the user system interface cable c onnections by accessing ports and checking the bus states of the pins. If ...

  • Renesas H8/33937 - page 19

    Figure 9 shows the Expansion I/O board Subclock Selecti on, and figure 10 shows the location of jumpers P4 and P5. Figure 11 shows the system clock oscillator on the user system interface cable and the subclock input specifications. USER INT E RFA C E6000 E MU L ATOR E CABLE E6000 160kHz 76.8kHz Subclock selection Figure 9 Expansion I/O board Subcl ...

  • Renesas H8/33937 - page 20

    Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correct ly aligned with pin 1 on t he cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MCU. 3. To avoid breaking wires in the cable body, d ...

Manufacturer Renesas Category Computer Hardware

Documents that we receive from a manufacturer of a Renesas H8/33937 can be divided into several groups. They are, among others:
- Renesas technical drawings
- H8/33937 manuals
- Renesas product data sheets
- information booklets
- or energy labels Renesas H8/33937
All of them are important, but the most important information from the point of view of use of the device are in the user manual Renesas H8/33937.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Renesas H8/33937, service manual, brief instructions and user manuals Renesas H8/33937. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Renesas H8/33937.

Similar manuals

A complete manual for the device Renesas H8/33937, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Renesas H8/33937 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Renesas H8/33937.

A complete Renesas manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Renesas H8/33937 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Renesas H8/33937, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Renesas H8/33937, that we can find in the current document
3. Tips how to use the basic functions of the device Renesas H8/33937 - which should help us in our first steps of using Renesas H8/33937
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Renesas H8/33937
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Renesas H8/33937 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Renesas H8/33937?

Use the form below

If you did not solve your problem by using a manual Renesas H8/33937, ask a question using the form below. If a user had a similar problem with Renesas H8/33937 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)