English dropdown-ico

Manual JVC LST0979-001B

32 pages 0.87 mb
Download

Go to site of 32

Summary
  • JVC LST0979-001B - page 1

    OUTDOOR DOME CAMERA TK-C2201WPU (For USA and Canada) TK-C2201WPE (For Europe) INSTRUCTIONS . For Customer Use: Enter below the Serial No. which is located on the body. Retain this information for future reference. Model No. TK-C2201WPU,TK-C2201WPE Serial No. LST0979-001B ...

  • JVC LST0979-001B - page 2

    Contents Introduction Contents ............................................................................................................. 2 Features ............................................................................................................. 3 Operating Precautions ................................................................ ...

  • JVC LST0979-001B - page 3

    Thank you for purchasing this product. Before use, please read this "INSTRUCTIONS" and the information materials included to ensure proper use of this product. These instructions are for TK-C2201WPU/TK-C2201WPE. TK-C2201WPE is not evaluated by UL. Features v Easy DAY/NIGHT function (TK-C2201WPU) v DAY/NIGHT surveillance with auto IR cut f ...

  • JVC LST0979-001B - page 4

    Operating Precautions m Storage and Location of Use v Do not install the camera in the following places. - In a place with vapor or oil, for example in a kitchen. - When the ambient temperature rises above or falls below the acceptable range (from -10 f to 50 f ) - In a place at which corrosive gases are emitted. - Near a source of radiation, X-ray ...

  • JVC LST0979-001B - page 5

    m Disclaimer v We will not be responsible for any inconveniences or disturbances caused in the event of privacy invasion as a result of camera footages of this product. m Others v When using this camera with [AGC] set to "MID" or "HIGH", the sensitivity increases automatically for dark images and the screen may appear grainy, bu ...

  • JVC LST0979-001B - page 6

    Name of Parts Camera . . A D E B C J K F H I G A Mounting Hole 2 2 ( A page 14) B Fall Prevention Wire Mounting Screw ( A page 14) C Conduit Plug/Hole (side) ( A page 21) D Dome Cover ( A page 13) E Inner Dome ( A page 13) F Video signal output connector (BNC) ( A page 10) ( A page 15) Introduction 6 ...

  • JVC LST0979-001B - page 7

    G Protection Cover ( A page 15) H Power Supply Cable ( A page 11) ( A page 15) I Hole for Connecting Cables, Conduit Hole ( A page 20) J Base ( A page 19) K Dome Cover Fastening Screw 2 3 ( A page 13) Introduction 7 ...

  • JVC LST0979-001B - page 8

    Name of Parts (Continued) Camera (Interior) The dome cover and inner dome are removed. . . D C H A B L 1 F ADJ MENU MONITOR SET MONITOR TYPE NOT USED DIPSW SEE INSTRUCTION MANUAL BLC OFF D/N AUTO CRT 1 2 3 4 OFF LCD ON F ADJ M N E G I F P Q R S O J K A Focus Adjustment Ring ( A page 25) B Zoom Adjustment Ring ( A page 25) C Rotation Knob ( A page 2 ...

  • JVC LST0979-001B - page 9

    F Space for Inserting Heater When mounting the heater (sold separately: KA-ZH215U), read the instruction manual of the heater before mounting. G Power Supply Connector for Heater For connecting to the power supply connector of the heater. H Tilt Fastening Screw 2 2 ( A page 24) I [MONITOR] Terminal (RCA pin) ( A page 23) J Lug Plate ( A page 16) K ...

  • JVC LST0979-001B - page 10

    About Connection Cables The maximum connection distance varies with the type of cable used. v Be sure to turn off the power of devices before connecting cables. . . To Power Supply To video Signal Cable Memo v Connect to AC 24 V power supply if using the heater (sold separately: KA-ZH215U). Video signal cable (coaxial cable) Connect a 75 K coaxial ...

  • JVC LST0979-001B - page 11

    DC 12 V or AC 24 V power supply cable Connect the power cord to the DC 12 V or the AC 24 V power supply. The unit is to be powered by a UL Listed Class 2 power supply only. (For USA and Canada) The AC 24 V and DC 12 V power supply shall conform to the following: UL Listed Class 2 power supply only, Class 2 not wet and Class 3 wet wiring (For USA) I ...

  • JVC LST0979-001B - page 12

    Setting the Switches Before mounting the camera, set the function setting switches on the camera. To set the switches, use a fine-tipped screwdriver. . . D/N 1 2 3 4 AUTO BLC OFF ON MONIT OR TYP E CRT LCD - - NOT UESD OFF Function selection switches DIP Switch Settings Chart 1 [D/N AUTO/OFF] Day & Night Switch Set this to "AUTO" when ...

  • JVC LST0979-001B - page 13

    Mounting the Camera Selecting a mounting method v Mount directly to the ceiling or on the wall ( A page 13) v Mounting the Camera Using the Conduit Hole at the Bottom of the Base ( A page 19) v Mounting the Camera Using the Conduit Hole at the Side of the Base ( A page 21) v Mounting the Camera using the Electrical Box ( A page 22) Memo When mounti ...

  • JVC LST0979-001B - page 14

    Mounting the Camera (Continued) m Mounting the Camera Unit 1 Make a hole ( Φ 30 mm) in the ceiling using the template provided 2 Mount the fall prevention wire for connecting the camera unit to the ceiling The fall prevention wire is not provided. Prepare a wire, taking into due consideration the length, strength, pull and material (insulating). ? ...

  • JVC LST0979-001B - page 15

    m Connecting the cable For safety reasons, turn on the power only after all the connection is complete. The status indicator lights up when the camera is turned on. 1 Connect the coaxial cable ( A page 10) Lower the protection cover and connect the connectors. Upon connecting, restore the protection cover to cover the connectors. This will isolate ...

  • JVC LST0979-001B - page 16

    Mounting the Camera (Continued) m Process after connection Fill the conduit hole and mounting holes with sealing agent and insert the silica gel. 1 Fill the conduit hole and the screw mounted holes (2 locations) with sealing agent (GE silicon) Note Seal the holes completely. Failure to do so may cause water or moisture to enter, thereby fogging the ...

  • JVC LST0979-001B - page 17

    m Adjusting images After mounting is completed, adjust the images while checking the actual image. ( A page 23) m Mounting the Dome Cover Attach the dome cover back when all settings are finished. 1 Mount the inner dome Mount the inner dome in a way that supports the tilt direction of the lens. Insert the inner depression of the inner dome into the ...

  • JVC LST0979-001B - page 18

    Mounting the Camera (Continued) 2 Mount the dome cover ① Clean the dust and dirt on the dome cover. ② Align the position marks (3 locations) on the camera unit and dome cover, followed by pressing in directly to mount the cover. ③ Tighten the dome cover fastening screw. . . Position alignment mark (x 3) Dome cover Dome cover protective sheet ...

  • JVC LST0979-001B - page 19

    Mounting the Camera Using the Conduit Hole at the Bottom of the Base Conduit hole: G3/4-14 UNC (TK-C2201WPU), M25 (TK-C2201WPE) 1 Remove the dome cover and inner dome ( A page 13) 2 Remove the camera unit from the base and mount the fall prevention wire to the camera unit ① Loosen the camera unit fastening screw (2 locations) with a screwdriver. ...

  • JVC LST0979-001B - page 20

    Mounting the Camera (Continued) 3 Wind the sealing tape Wind the sealing tape around the pipe junction (where the conduit hole thread lines with the pipe screw hole) two or more times. 4 Mount the base to the pipe Turn and screw the base unit to the pipe in the clockwise direction. Note When screwing the pipe, do not screw beyond 12 mm. Doing so ca ...

  • JVC LST0979-001B - page 21

    Mounting the Camera Using the Conduit Hole at the Side of the Base If the camera cannot be mounted directly to the ceiling, use the conduit hole at the side of the base to mount the camera to the pipe. Conduit hole: G3/4-14 UNC (TK-C2201WPU), M25 (TK-C2201WPE) 1 Remove the dome cover and inner dome ( A page 13) 2 Remove the camera unit from the bas ...

  • JVC LST0979-001B - page 22

    Mounting the Camera (Continued) Mounting the Camera using the Electrical Box 1 Remove the dome cover and inner dome ( A page 13) 2 Mount the camera unit to the electrical box Mount the camera unit to the electrical box using the mounting hole (2 locations) with the M4 screw (2 pieces). Memo The screws are not provided. . . M4 Screw 4 Inch square el ...

  • JVC LST0979-001B - page 23

    Adjusting Image After mounting the camera, adjust the images while looking at the actual image. Discharge the static electricity from your body by touching the metallic part of the monitor terminal before handling the camera as static electricity may cause the camera to malfunction. 1 Mount the monitor Connect the monitor terminal of this camera to ...

  • JVC LST0979-001B - page 24

    Adjusting Image (Continued) 3 Adjust the shooting direction of the camera Adjust the camera for pan, tilt and rotation, and face the camera towards the subject. . MONITOR TYPE NOT USED DIPSW SEE INSTRUCTION MANUAL BLC OFF D/N AUTO CRT 1 2 3 4 OFF LCD ON 1 F ADJ MENU Tilt: 80 Rotation: 100 Pa n : 1 75 Tilt fastening scre w Shooting direction mark Pa ...

  • JVC LST0979-001B - page 25

    4 Adjust the image size Loosen the fastening screw for the zoom adjustment ring and move the ring to the left/right to adjust the image size. After adjustment is complete, fasten the screw. 5 Adjust the focus ① Hold the focus adjust gear knob, shift the catch from point A to point B as illustrated in the diagram to disengage the gear. Note To pre ...

  • JVC LST0979-001B - page 26

    Adjusting Image (Continued) 6 Fine adjust the focus ① Press and hold the [ J ] button. v Focus adjust mode will be activated and "FOCUS ADJUST MODE" is displayed on the monitor screen. v The contours are emphasized as the iris opens and the depth of field becomes shallow. v After adjustment, press [ K , H , I ]/[SET]/[MENU] to exit focu ...

  • JVC LST0979-001B - page 27

    7 Tighten the fastening screw of the focus adjustment ring Hold and press the focus adjust gear between your fingers in the direction of the arrows in the diagram, and tighten the fastening screw of the focus adjustment ring. . . Foc us adjustment r ing Adjustment 27 ...

  • JVC LST0979-001B - page 28

    Adjusting the Auto White Balance Each light source has its own color temperature. Therefore, when the main light source lighting the subject is changed, adjust the white balance again. 1 Press the [MENU] button. 2 Select [WHITE BALANCE] with the [ J / K ] button and "AWC" with the [ H / I ] button, then press the [SET] button. 3 Zoom in t ...

  • JVC LST0979-001B - page 29

    Specifications Horizontal resolution : 550TV lines (typical) Video S/N ratio : 52 dB (typical, AGC OFF) Minimum illumination : Color mode: 0.05 lx (typical, 50 %, F1.2, AGC HIGH) Black and White mode: 0.03 lx (TK-C2201WPU) (typical, 50 %, F1.2, AGC HIGH) 0.006 lx (TK-C2201WPE) (typical, 50 %, F1.2, AGC HIGH) Zoom ratio : 3.75 Focal length : 2.8 mm ...

  • JVC LST0979-001B - page 30

    Specifications (Continued) Accessories : (TK-C2201WPU) WARRANTY CARD 2 1 INSTRUCTIONS 2 3 Silica gel 2 1 Wrench 2 1 Template 2 1 (TK-C2201WPE) INSTRUCTIONS 2 5 Silica gel 2 1 Wrench 2 1 Template 2 1 Others 30 ...

  • JVC LST0979-001B - page 31

    m External dimensions [Unit: mm (inch)] . . 121(4-3/4) 113(4-1/2) 160(6-1/4) 9 5(1/4) 42(1-5/8) 125(4-7/8) 160(6-1/4) SR53.7 (3/8) Screw f or conduit (bottom surface , side surface) (TK-C2201WPU: G3/4-14 UNC, T K -C2201WPE: M25) (2-1/8) * Specifications and appearance of this camera are subject to change for improvements without notice. Others 31 ...

  • JVC LST0979-001B - page 32

    TK-C2201WPU/ TK-C2201WPE OUTDOOR DOME CAMERA Q 2009 Victor Company of Japan, Limited LST0979-001B ...

Manufacturer JVC Category Security Camera

Documents that we receive from a manufacturer of a JVC LST0979-001B can be divided into several groups. They are, among others:
- JVC technical drawings
- LST0979-001B manuals
- JVC product data sheets
- information booklets
- or energy labels JVC LST0979-001B
All of them are important, but the most important information from the point of view of use of the device are in the user manual JVC LST0979-001B.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals JVC LST0979-001B, service manual, brief instructions and user manuals JVC LST0979-001B. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product JVC LST0979-001B.

Similar manuals

A complete manual for the device JVC LST0979-001B, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use JVC LST0979-001B by users. Manuals are usually written by a technical writer, but in a language understandable to all users of JVC LST0979-001B.

A complete JVC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual JVC LST0979-001B - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the JVC LST0979-001B, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the JVC LST0979-001B, that we can find in the current document
3. Tips how to use the basic functions of the device JVC LST0979-001B - which should help us in our first steps of using JVC LST0979-001B
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with JVC LST0979-001B
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of JVC LST0979-001B in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning JVC LST0979-001B?

Use the form below

If you did not solve your problem by using a manual JVC LST0979-001B, ask a question using the form below. If a user had a similar problem with JVC LST0979-001B it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)