English dropdown-ico

Manual NETGEAR ETHERNET SWITCH SW108

40 pages 1.17 mb
Download

Go to site of 40

Summary
  • NETGEAR ETHERNET SWITCH SW108 - page 1

    M-SW108NA-0 June 1997 NETGEAR , Inc. A Bay Networks Company 48015 Warm Springs Blvd. Fremont, CA 94539 USA Installation Guide f or the Model SW108 Ethernet Switc h SW108.BK Page i Friday, June 27, 1997 10:48 AM ...

  • NETGEAR ETHERNET SWITCH SW108 - page 2

    ii © 1997 by NETGEAR, Inc. All rights reserved. T rademarks Bay Networks is a re gistered trademark of Bay Networks, Inc. NETGEAR is a trademark of Bay Networks, Inc. Other brand and product names are registered trademarks or trademarks of their respecti ve holders. Statement of Conditions In the interest of improving internal design, operational ...

  • NETGEAR ETHERNET SWITCH SW108 - page 3

    iii V oluntar y Control Council f or Interference (VCCI) Statement This equipment is in the first category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set by the V oluntary Control Council for Interference by Data Processing Equipment and Electronic Of fice Machines that are aimed at prev ...

  • NETGEAR ETHERNET SWITCH SW108 - page 4

    iv SW108.BK Page iv Friday, June 27, 1997 10:48 AM ...

  • NETGEAR ETHERNET SWITCH SW108 - page 5

    Contents v Contents Chapter 1 Introduction Benefits of Using Switching T echnology ......................................................................... 1-1 T ypes of Ethernet Switches ............................................................................................ 1-2 Model SW108 Switch Ov er view ................................. ...

  • NETGEAR ETHERNET SWITCH SW108 - page 6

    vi Contents Chapter 5 T roub leshooting T roub leshooting the Switch and the Networ k ................................................................. 5-1 Appendix A T echnical Specifications General Specifications ................................................................................................... A-1 Appendix B Connector Pin Ass ...

  • NETGEAR ETHERNET SWITCH SW108 - page 7

    Figures vii Figures Figure 2-1. F ront panel of the Model SW108 s witch .................................................. 2-1 Figure 2-2. The vista RJ-45 connector with built-in LEDs .......................................... 2-2 Figure 2-3. Rear panel of the Model SW108 s witch ................................................... 2-4 Figure 3-1. U ...

  • NETGEAR ETHERNET SWITCH SW108 - page 8

    viii Tables T ables T ab le 2-1. LED descriptions ...................................................................................... 2-3 T ab le 5-1. T roub leshooting ........................................................................................ 5-1 T ab le B-1. RJ-45 plug and vista RJ-45 connector pin assignments ................... ...

  • NETGEAR ETHERNET SWITCH SW108 - page 9

    Introduction 1-1 Chapter 1 Intr oduction Congratulations on your purchase of the NETGEAR ™ Model SW108 8-port Ethernet Switch. The Model SW108 switch segments Ethernet netw orks to relie ve bandwidth congestion instantly , without having to replace netw ork wiring, interface cards, or software. This guide describes ho w to install and use the swi ...

  • NETGEAR ETHERNET SWITCH SW108 - page 10

    Installation Guide for the Model SW108 Ethernet Switch 1-2 Introduction This bandwidth improv ement is accomplished very easily , with no change to the desktop (the network interface cards or softw are, and network wiring). As a result, the performance upgrade and the applications it enables are obtained very quickly and at a lo w cost. T ypes of E ...

  • NETGEAR ETHERNET SWITCH SW108 - page 11

    Installation Guide for the Model SW108 Ethernet Switch Introduction 1-3 Features The Model SW108 switch has the follo wing ke y features: • Eight switched, 10 Mbps, Ethernet 10B ASE-T ports • Full-duplex or half-duple x mode of operation Full-duplex mode doubles throughput of point-to-point connections by letting indi vidual ports transmit and ...

  • NETGEAR ETHERNET SWITCH SW108 - page 12

    SW108.BK Page 4 Friday, June 27, 1997 10:48 AM ...

  • NETGEAR ETHERNET SWITCH SW108 - page 13

    Physical Description 2-1 Chapter 2 Ph ysical Description This chapter explains the hardw are features of the NETGEAR Model SW108 Ethernet switch. It is di vided into sections explaining the front and rear panels of the switch. Use the k ey at the bottom of each illustration to identify the panel components. Fr ont P anel For easier management and c ...

  • NETGEAR ETHERNET SWITCH SW108 - page 14

    Installation Guide for the Model SW108 Ethernet Switch 2-2 Physical Description Ethernet P or ts The Model SW108 switch is equipped with eight 10 Mbps Ethernet ports that support one cable connection, unshielded twisted pair (UTP) cable. An eight-pin RJ-45 plug is used for connection to these ports. Each port uses vista RJ-45 connectors that hav e ...

  • NETGEAR ETHERNET SWITCH SW108 - page 15

    Installation Guide for the Model SW108 Ethernet Switch Physical Description 2-3 LEDs Y ou use LEDs on the Model SW108 switch to monitor and diagnose the de vices. LEDs on the front panel of the switch and two LEDs on each port allo w you to identify the following information: • Status of the switch po wer supply • Data transmission or recei ve ...

  • NETGEAR ETHERNET SWITCH SW108 - page 16

    Installation Guide for the Model SW108 Ethernet Switch 2-4 Physical Description Rear P anel As illustrated in Figure 2-3, the rear panel has full-duplex (FDX), and half-duple x (HDX) toggle switches, a ground clip, and a standard A C po wer receptacle. Key : 1 = Ground clip 2 = FDX and HDX toggle s witches to set the duplex mode of each 10 Mbps por ...

  • NETGEAR ETHERNET SWITCH SW108 - page 17

    Applications 3-1 Chapter 3 Applications This chapter presents an ov erview of the le vels of service provided by incorporating the technology of the NETGEAR Model SW108 Ethernet switch into your network. The Model SW108 Ethernet switch is designed to provide fle xibility in configuring your network connections. Each switch can be used as a standa ...

  • NETGEAR ETHERNET SWITCH SW108 - page 18

    Installation Guide for the Model SW108 Ethernet Switch 3-2 Applications Desktop Switching Figure 3-1 illustrates the Model SW108 switch used as a desktop switch to build a small netw ork that enables users to hav e 10 Mbps access to a file server . Key : 1 = Ser v er with 10 Mbps connection 2 = Model SW108 Ethernet switch (Normal/Uplink push butto ...

  • NETGEAR ETHERNET SWITCH SW108 - page 19

    Installation Guide for the Model SW108 Ethernet Switch Applications 3-3 Segment Switching The Model SW108 switch can segment a netw ork into multiple connected pieces, increasing ov erall bandwidth and throughput. Figure 3-2 illustrates the Model SW108 Ethernet switch segmenting netw orks that are b uilt with the NETGEAR Model EN104 and Model EN108 ...

  • NETGEAR ETHERNET SWITCH SW108 - page 20

    SW108.BK Page 4 Friday, June 27, 1997 10:48 AM ...

  • NETGEAR ETHERNET SWITCH SW108 - page 21

    Installation 4-1 Chapter 4 Installation This chapter provides information about installing the Model SW108 Ethernet switch and information about verifying installation. Preparing the Site Before you begin installing the switch, prepare the installation site. Mak e sure the operating en vironment meets the physical requirements of the equipment as d ...

  • NETGEAR ETHERNET SWITCH SW108 - page 22

    Installation Guide for the Model SW108 Ethernet Switch 4-2 Installation Installing the Switch on a Desktop Choose a location near the de vices to be connected and close to an electrical outlet. Set the switch on a desktop or tabletop, allo wing at least two inches (5 cm) of space on all sides to pre vent restriction of airflo w . Connecting De vic ...

  • NETGEAR ETHERNET SWITCH SW108 - page 23

    Installation Guide for the Model SW108 Ethernet Switch Installation 4-3 3. Set the FDX or HDX toggle switches on the rear panel f or the selected duplex mode. A hub and repeater use a common collision domain for all communications and cannot support full-duplex mode. When connecting any of the 10 Mbps ports on the switch to a hub, set the port to H ...

  • NETGEAR ETHERNET SWITCH SW108 - page 24

    SW108.BK Page 4 Friday, June 27, 1997 10:48 AM ...

  • NETGEAR ETHERNET SWITCH SW108 - page 25

    Troubleshooting 5-1 Chapter 5 T r oubleshooting This chapter provides information about troubleshooting the NETGEAR Model SW108 Ethernet switch. T r oubleshooting the Switch and the Netw ork T o troubleshoot the switch and the network, refer to T able 5-1. T able 5-1. T roub leshooting Symptom Activity Check No power at s witch P ow er LED off Chec ...

  • NETGEAR ETHERNET SWITCH SW108 - page 26

    Installation Guide for the Model SW108 Ethernet Switch 5-2 Troubleshooting P or t connection not functioning Link LED off or inter mittent After the cab ling has been installed, if the Link LED is not lit on an activ e por t, chec k the attached de vice and make sure that it is pow ered on and there is a proper UTP connection at that end. Also make ...

  • NETGEAR ETHERNET SWITCH SW108 - page 27

    Technical Specifications A-1 Appendix A T echnical Specifications This appendix provides technical specifications for the NETGEAR Model SW108 switch. General Specifications Network Pr otocol and Standard ISO/IEC 802-3 (ANSI/IEEE 802.3i 10B ASE-T , Ethernet Data Rate 10 Mbps Manchester encoded Interface RJ-45 connector for 10B ASE-T Ethernet inte ...

  • NETGEAR ETHERNET SWITCH SW108 - page 28

    Installation Guide for the Model SW108 Ethernet Switch A-2 Technical Specifications En vironmental Specifications Operating temperature: 0 ° to 40 ° C (32 ° to 104 ° F) Storage temperature: -25 ° to 70 ° C (-13 ° to 158 ° F) Operating humidity: 80% maximum relati ve humidity , noncondensing Storage humidity: 95% maximum relati ve humidity ...

  • NETGEAR ETHERNET SWITCH SW108 - page 29

    Installation Guide for the Model SW108 Ethernet Switch Technical Specifications A-3 Safety Agency Appr ovals f or P ower Adapter CE mark, commercial UL listed (UL 1950 ) CSA certified (CSA 22.2 #950) TUV licensed (EN 60 950) T -Mark P erformance Specifications Frame filter rate: 14,800 frames/second, maximum Frame forward rate: 14,800 frames/sec ...

  • NETGEAR ETHERNET SWITCH SW108 - page 30

    SW108.BK Page 4 Friday, June 27, 1997 10:48 AM ...

  • NETGEAR ETHERNET SWITCH SW108 - page 31

    Connector Pin Assignments B-1 Appendix B Connector Pin Assignments This appendix provides information about the RJ-45 connector used for the NETGEAR Model SW108 Ethernet switch. RJ-45 Plug and vista RJ-45 Connector The RJ-45 plug accepts 4-pair unshielded twisted pair (UTP) or shielded twisted pair (STP) 100 Ω cable and connects into the vista RJ ...

  • NETGEAR ETHERNET SWITCH SW108 - page 32

    Installation Guide for the Model SW108 Ethernet Switch B-2 Connector Pin Assignments T able B-1 lists the pin assignments for the RJ-45 plug and the vista RJ-45 connector . * Applicable to port1 on the Model SW108 switch, when the Normal/Uplink push button is in the Uplink position. T able B-1. RJ-45 plug and vista RJ-45 connector pin assignments P ...

  • NETGEAR ETHERNET SWITCH SW108 - page 33

    Cabling Guidelines C-1 Appendix C Cabling Guidelines This appendix provides information on the cable specifications and guidelines for Cate gory 5 UTP cabling used with the NETGEAR Model SW108 Ethernet switch. Ethernet T echnology When 10B ASE-T technology was originally introduced, multiple repeaters were frequently used to build lar ge networks. ...

  • NETGEAR ETHERNET SWITCH SW108 - page 34

    Installation Guide for the Model SW108 Ethernet Switch C-2 Cabling Guidelines T able C-1 lists the electrical requirements of the Category 3, 4, and 5 cables. T wisted P air Cables For tw o de vices to communicate, the transmitter of each de vice must be connected to the recei ver of the other de vice. The crosso ver function is usually implemented ...

  • NETGEAR ETHERNET SWITCH SW108 - page 35

    Installation Guide for the Model SW108 Ethernet Switch Cabling Guidelines C-3 Figure C-1 illustrates straight-through twisted pair cable connections. Key : A = Uplink or MDI por t (As on a PC) B = Normal or MDI-X por t (As on a hub or s witch) 1, 2, 3, 6 = Connector pins Figure C-1. Straight-through twisted pair cable Figure C-2 illustrates crossov ...

  • NETGEAR ETHERNET SWITCH SW108 - page 36

    SW108.BK Page 4 Friday, June 27, 1997 10:48 AM ...

  • NETGEAR ETHERNET SWITCH SW108 - page 37

    Index 1 Numbers 10 Mbps ports, 2-1, 2-4 A applications desktop switching, 3-2 segment switching, 3-3 C cable crossov er twisted pair, 4-2, C-3 specifications, C-1 straight-through twisted pair , 4-2, 5-2, C-3 troubleshooting, 5-2 Collision LED, 2-1, 2-3, 5-1 crossov er twisted pair cable, 4-2, C-3 customer support, iii D data collisions, 5-1 deskt ...

  • NETGEAR ETHERNET SWITCH SW108 - page 38

    Installation Guide for the Model SW108 Ethernet Switch 2 Index P package contents, 4-1 ports, 10 Mbps, 2-1, 2-4 Po wer LED, 2-1, 2-3, 4-3, 5-1 R rear panel, 2-4 RJ-45 connector . See vista RJ-45 connector RJ-45 plug using to connect to 10 Mbps ports, 2-2 using with UTP and STP cable, B-1 Rx/Tx LED, 2-3, 4-3, 5-1 S segment switching, 1-2, 3-3 site p ...

  • NETGEAR ETHERNET SWITCH SW108 - page 39

    SW108.BK Page 3 Friday, June 27, 1997 10:48 AM ...

  • NETGEAR ETHERNET SWITCH SW108 - page 40

    SW108.BK Page 4 Friday, June 27, 1997 10:48 AM ...

Manufacturer NETGEAR Category Switch

Documents that we receive from a manufacturer of a NETGEAR ETHERNET SWITCH SW108 can be divided into several groups. They are, among others:
- NETGEAR technical drawings
- ETHERNET SWITCH SW108 manuals
- NETGEAR product data sheets
- information booklets
- or energy labels NETGEAR ETHERNET SWITCH SW108
All of them are important, but the most important information from the point of view of use of the device are in the user manual NETGEAR ETHERNET SWITCH SW108.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals NETGEAR ETHERNET SWITCH SW108, service manual, brief instructions and user manuals NETGEAR ETHERNET SWITCH SW108. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product NETGEAR ETHERNET SWITCH SW108.

Similar manuals

A complete manual for the device NETGEAR ETHERNET SWITCH SW108, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use NETGEAR ETHERNET SWITCH SW108 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of NETGEAR ETHERNET SWITCH SW108.

A complete NETGEAR manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual NETGEAR ETHERNET SWITCH SW108 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the NETGEAR ETHERNET SWITCH SW108, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the NETGEAR ETHERNET SWITCH SW108, that we can find in the current document
3. Tips how to use the basic functions of the device NETGEAR ETHERNET SWITCH SW108 - which should help us in our first steps of using NETGEAR ETHERNET SWITCH SW108
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with NETGEAR ETHERNET SWITCH SW108
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of NETGEAR ETHERNET SWITCH SW108 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning NETGEAR ETHERNET SWITCH SW108?

Use the form below

If you did not solve your problem by using a manual NETGEAR ETHERNET SWITCH SW108, ask a question using the form below. If a user had a similar problem with NETGEAR ETHERNET SWITCH SW108 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)