English dropdown-ico

Manual Chicago Electric 91511

17 pages 0.43 mb
Download

Go to site of 17

Summary
  • Chicago Electric 91511 - page 1

    7” POR T ABLE WET TILE SA W Model 91511 ASSEMBL Y AND OPERA TING INSTR UCTIONS Distributed Exclusiv ely by Harbor F reight T ools 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .harborfreight.com Cop yr ight © 2004 b y Harbor F reight T ools ® . All rights reser ved. No por tion of this manual or any ar twork co ...

  • Chicago Electric 91511 - page 2

    PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual f or the safety w ar nings and precautions , assembly , operat- ing, inspection, maintenance and cleaning procedures, par ts list and assemb ly diagram. K eep your in voice with this manual. Wr ite the in v oice number on the inside of the front cov er . K eep this manual and in ...

  • Chicago Electric 91511 - page 3

    3. Keep b ystanders, children, and visitors awa y while operating a power tool. Distractions can cause y ou to lose control. Protect others in the work area from debris such as chips and spar ks. Provide barriers or shields as needed. PERSONAL SAFETY 1. Stay alert. W atch what you are doing, and use common sense when oper - ating a power tool. Do n ...

  • Chicago Electric 91511 - page 4

    2. Do not use the power tool if the P ower Switc h does not turn it on or off. Any tool that cannot be controlled with the P ower Switch is dangerous and must be replaced. 3. Disconnect the P ower Cor d Plug from the po wer source bef ore making any adjustments, changing accessories, or storing the tool. Such prev entive saf ety measures reduce the ...

  • Chicago Electric 91511 - page 5

    2. Double insulated tools are equipped with a polarized plug (one prong is wider than the other). This plug will fit in a polarized outlet only one wa y . If the plug does not fit fully in the outlet, rever se the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any wa y . ...

  • Chicago Electric 91511 - page 6

    resistance path to carr y electricity aw a y from the user , reducing the r isk of elec- tric shock. (See Figure A.) 2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’ s grounding system and must ne v er ...

  • Chicago Electric 91511 - page 7

    5. If you are using one e xtension cord f or more than one tool, add the nameplate amperes and use the sum to deter mine the required minimum cord siz e. (See Figure B.) 6. If you are using an e xtension cord outdoors, mak e sure it is mar k ed with the suf- fix “W-A” (“W” in Canada) to indicate it is acceptab le for outdoor use . 7. Make ...

  • Chicago Electric 91511 - page 8

    SPECIFIC SAFETY R ULES 1. Maintain labels and nameplates on the W et Tile Saw . These carr y impor tant inf or mation. If unreadable or missing, contact Harbor F reight T ools for a replace- ment. 2. D ANGER! Keep hands and fingers a way fr om cutting area and Saw Blade. Use a appropriate push stic k (not included) whene ver possib le. 3. Check Bl ...

  • Chicago Electric 91511 - page 9

    13. Bef ore using the W et Tile Saw , make sure the Saw Blade is pr operly mounted on the Saw Spindle. Make sure the Sa w Blade is balanced, and is not crac ked or bent. 14. The Saw Blade will become hot while cutting. Allo w the Saw Blade to completely cool bef ore touching. 15. Allow the Sa w Blade to spin up to full speed before feeding a w orkp ...

  • Chicago Electric 91511 - page 10

    SKU 91511 P A GE 10 25. W ARNING! People with pacemaker s should consult their ph ysician(s) before using this pr oduct. Electromagnetic fields in close proximity to a hear t pacemaker could cause interf erence to or f ailure of the pacemaker . 26. W ARNING! Some dust created by po wer sanding, sa wing, gr inding, drilling, and other construction ...

  • Chicago Electric 91511 - page 11

    SKU 91511 P A GE 11 Saw Blade (6) from the Spindle of the Wet Tile Saw . Then, install a new diamond Saw Blade with a 7” diameter , 5/8” round arbor hole, and rated at a mini- mum 3,600 RPM. (See Figure D.) 6. NO TE: When installing the new Saw Blade (6), mak e sure the directional arrow shown on the Sa w Blade is pointing toward the front of t ...

  • Chicago Electric 91511 - page 12

    SKU 91511 P A GE 12 3. Check to mak e sure the Blade Guard (2) mov es freely upward and downw ard. (See Figure D .) 4. Close the Left Side Cutting T ab le (26). (See Figure D.) T o Attach The Fence And Miter Guide: 1. Place the F ence (11) on top of the Right Cutting T able (10) and clamp both ends of the F ence to secure it in place. The F ence is ...

  • Chicago Electric 91511 - page 13

    SKU 91511 P A GE 13 3. Make sure the P ower Switch (21) is in its “OFF” position. Then, plug the P ower Cord (17) into the nearest 120 v olt, grounded, electrical outlet. (See Figure G.) T o P erform Straight Cutting: 1. Lift the front and rear Le vers of the F ence (11). Slide the F ence along the T ab le to the left or right until the desired ...

  • Chicago Electric 91511 - page 14

    SKU 91511 P A GE 14 FIGURE G WORKPIECE (NO T INCLUDED) FENCE (11) FENCE SCALE FENCE LEVER FENCE LEVER PO WER SWITCH (21) 2. Raise the Right Cutting T ab le (10) to the desired angle of cut (i.e., 15, 30, 45, or 60 ). (See Figure next page .) 3. Place the two Stands underneath the Right Cutting T able (10) into the groo ves to hold the Cutting T ab ...

  • Chicago Electric 91511 - page 15

    SKU 91511 P A GE 15 FIGURE H RIGHT CUTTING T ABLE (10) WORKPIECE (NO T INCLUDED) PO WER SWITCH (21) ST AND (0 to 60 ) and tighten the Lock Knob to loc k the Miter Guide in place. (See Figure I.) 3. Place the workpiece flush against the Miter Guide (24). T urn the P ower Switch (21) toits “ON” position, and allow the Sa w Blade (6) to spin up t ...

  • Chicago Electric 91511 - page 16

    INSPECTION, MAINTENANCE, AND CLEANING 1. W ARNING! Always make sure the P ower Switc h (21) is in its “OFF” position, and unplug the P ower Cord (17) fr om its 120 volt electrical outlet before perf orming any inspection, adjustments, maintenance, or c leaning. 2. Before eac h use , inspect the general condition of the W et Tile Saw . Check f o ...

  • Chicago Electric 91511 - page 17

    P AR TS LIST SKU 91511 P A GE 17 P AR TS LIST SKU 91511 P A GE 17 Part # Description Qt y . Part # Description Qty. 1 Screw 1 18 Motor Bottom Base 1 2 Blade Guard 1 19 Electrical Cord Fixed Head 1 3 Wing Nut 1 20 Capacitor 1 4 Guard Support 1 21 Power Switch 1 5 Screw 1 22 Rubber Stand Screw 4 6 Continuous Rim Blade (7”) 1 23 Rubber Stand 4 7 Inn ...

Manufacturer Chicago Electric Category Saw

Documents that we receive from a manufacturer of a Chicago Electric 91511 can be divided into several groups. They are, among others:
- Chicago Electric technical drawings
- 91511 manuals
- Chicago Electric product data sheets
- information booklets
- or energy labels Chicago Electric 91511
All of them are important, but the most important information from the point of view of use of the device are in the user manual Chicago Electric 91511.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Chicago Electric 91511, service manual, brief instructions and user manuals Chicago Electric 91511. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Chicago Electric 91511.

Similar manuals

A complete manual for the device Chicago Electric 91511, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Chicago Electric 91511 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Chicago Electric 91511.

A complete Chicago Electric manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Chicago Electric 91511 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Chicago Electric 91511, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Chicago Electric 91511, that we can find in the current document
3. Tips how to use the basic functions of the device Chicago Electric 91511 - which should help us in our first steps of using Chicago Electric 91511
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Chicago Electric 91511
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Chicago Electric 91511 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Chicago Electric 91511?

Use the form below

If you did not solve your problem by using a manual Chicago Electric 91511, ask a question using the form below. If a user had a similar problem with Chicago Electric 91511 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)