English dropdown-ico

Manual Campbell Hausfeld IFN35650

24 pages 1.45 mb
Download

Go to site of 24

Summary
  • Campbell Hausfeld IFN35650 - page 1

    Description This nailer is designed for decorative trim, molding, window casings, furniture trim and picture frame assembly. Features include: convenient rear loading magazine which holds up to 100 nails, no-mar tip, adjustable exhaust, single cycle trigger, quick clear nose, and an adjustable depth of drive mechanism. General Safety Information CA ...

  • Campbell Hausfeld IFN35650 - page 2

    2 General Safety Information (Continued) • Do not touch the trigger unless driving nails. Never attach air line to nailer or carry nailer while touching the trigger. The tool could eject a fastener which will result in death or serious personal injury. Warning indicates a potentially hazardous situation which, if not avoided, COULD result in deat ...

  • Campbell Hausfeld IFN35650 - page 3

    RECOMMENDED HOOKUP The illustration below shows the recommended hookup for the nailer. 1. The air compressor must be able to maintain a minimum of 70 PSI when the nailer is being used. An inadequate air supply can cause a loss of power and inconsistent driving. 2. An oiler can be used to provide oil circulation through the nailer. A filter can be u ...

  • Campbell Hausfeld IFN35650 - page 4

    4. Reconnect air supply to the nailer. 5. Depress the Work Contact Element (WCE) against the work surface without pulling the trigger. The nailer MUST NOT OPERATE . Do not use the tool if it operates without pulling the trigger. Personal injury may result. 6. Remove the nailer from the work surface. The Work Contact Element (WCE) must return to its ...

  • Campbell Hausfeld IFN35650 - page 5

    4. The door can now be rotated, exposing the jammed fastener. 5. Remove the jammed fastener, using pliers or a screwdriver if required. 6 Rotate door back into the closed position. 7. Extend the wire latch and place over the hooks on the nose. 8. Close the latch by pushing the latch up and in until the latch snaps into place. 9. Make sure the trigg ...

  • Campbell Hausfeld IFN35650 - page 6

    Air leaking at trigger valve Air leaking between housing and nose Air leaking between housing and cap Nailer skips driving nail Nailer runs slow or has loss of power Nails are jammed in nailer O-Rings in trigger valve housing are damaged Loose screws in housing Damaged O-Rings Damage to bumper Loose screws Damaged gasket Worn bumper Dirt in nose pi ...

  • Campbell Hausfeld IFN35650 - page 7

    Limited W arranty 1. DURATION: From the date of purchase by the original purchaser as follows: One (1) Year. 2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6400 3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purpos ...

  • Campbell Hausfeld IFN35650 - page 8

    Notes 8 Model IFN35650 Operating Instructions www.chpower.com ...

  • Campbell Hausfeld IFN35650 - page 9

    Cesser d’utiliser tout outil s’il y a malaise, engourdissement, fourmillement ou douleur et consulter un médecin. Ce manuel contient des informations concernant la sécurité, le fonctionnement et l’entretien. Lire attentivement ce manuel et comprendre tous les avertissements de sécurité et les instructions avant d’utiliser la cloueuse. ...

  • Campbell Hausfeld IFN35650 - page 10

    Généralités Sur La Sécurité (Suite) • Toujours bien s’équilibrer pendant la manipulation ou l’utilisation de la cloueuse. • Ne jamais modifier ou empêcher le fonctionnement du mécanisme de déclenchement par contact (WCE) et ne jamais maintenir la gâchette enfoncée à l’aide de ruban adhésif par exemple. Ceci pourrait entraîne ...

  • Campbell Hausfeld IFN35650 - page 11

    Généralités Sur La Sécurité (Suite) • Ne jamais laisser la cloueuse sans surveillance ni branchée à un compresseur si hors-service. Il y a risque de blessures graves si la cloueuse est utilisée par une personne qui ne connait pas les instructions d’utilisation. • Ne pas échapper ni jeter l’outil car ceci peut causer du dommage le r ...

  • Campbell Hausfeld IFN35650 - page 12

    7. Actionner la gâchette. Appuyer le mécanisme de déclenchement par contact (WCE) sur la surface de travail. La cloueuse DOIT FONCTIONNER . 8. Appuyer le mécanisme de déclenche- ment par contact (WCE) sur la surface de travail. Actionner la gâchette. La cloueuse DOIT FONCTIONNER . CHARGEMENT DE LA CLOUEUSE 1. Toujours connecter l’outil à l ...

  • Campbell Hausfeld IFN35650 - page 13

    Utilisation de la Cloueuse (Suite) DÉCHARGEMENT DE LA CLOUEUSE 1. Toujours décharger toutes les attaches avant de mettre l’outil hors service. La méthode de déchargement est le contraire du chargement, mais toujours déconnecter le tuyau à air avant le déchargement. 2. Tirer en arrière le poussoir et presser le bouton de dérivation « Nai ...

  • Campbell Hausfeld IFN35650 - page 14

    14 Fr Modèle IFN35650 Instructions D’Utilisation Fuite d’air à l’endroit de la soupape de la gâchette Fuite d’air entre le carter et le nez Fuite d’air entre le carter et le capuchon La cloueuse saute un clou pendant l’expulsion La cloueuse fonctionne lentement ou a une perte de puissance Blocage des clous Joints torique endommagés ...

  • Campbell Hausfeld IFN35650 - page 15

    Garantie Limitée 1. DURÉE : De la date d'achat par l'acheteur original comme suit : un (1) an. 2. GARANTIE ACCORDÉE PAR (GARANT): Campbell Hausfeld/Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Téléphone: (800) 543-6400 3. BÉNÉFICIAIRE DE CETTE GARANTIE (ACHETEUR): L’acheteur original (sauf en cas de revente) ...

  • Campbell Hausfeld IFN35650 - page 16

    16 Fr Modèle IFN35650 Instructions D’Utilisation Notes ...

  • Campbell Hausfeld IFN35650 - page 17

    Descripción Esta clavadora está diseñada para trabajos de acabado, moldes interiores, bases, paneles y ensamblaje e instalación de gabinetes. Entre las características se incluyen: conveniente depósito que se carga port la parte posterior y sujeta hasta 100 clavos, punta que no se estropea, escape ajustable, gatillo de ciclo único, boca de d ...

  • Campbell Hausfeld IFN35650 - page 18

    Informaciones Generales de Seguridad (Continuación) • Siempre colóquese en una posición firme y balanceada para usar o manipular la clavadora. • No modifique ni deshabilite el Elemento de Contacto de Trabajo. No amarre ni pegue con cinta adhesiva el Elemento de Contacto de Trabajo ni el gatillo en una posición oprimida. Se puede producir la ...

  • Campbell Hausfeld IFN35650 - page 19

    2. Gire la clavadora de modo que la entrada de aire quede mirando hacia arriba. Agregue de 4 a 5 gotas de aceite no detergente 30W en la entrada de aire. No use aceites detergentes, aditivos de aceite, ni aceites para herramientas neumáticas. Los aceites para herramientas neumáticas contienen solventes que pueden averiar los componentes internos ...

  • Campbell Hausfeld IFN35650 - page 20

    Cómo usar la Clavadora (Continuación) 3. Use mangueras de aire de 9,5 mm diseñadas para presiones mínimas de trabajo de 150 psi. Use mangueras de aire de 12,7 mm si la longitud de las mismas es de 50' ó más. Para un mejor rendimiento, instalele a la clavadora un conector rápido de 9,5 mm (con roscas de 6,4 mm NPT) cuyo diámetro interno ...

  • Campbell Hausfeld IFN35650 - page 21

    Cómo usar la Clavadora (Continuación) PARA DESCARGAR LA CLAVADORA 1. Siempre sáquele todos los clavos a la clavadora antes de guardarla al terminar de usarla. Para descargar la unidad debe hacer lo contrario que se hace para cargarla, excepto que siempre debe desconectar la manguera de aire antes de comenzar a descargar la unidad. 2. Hale hacia ...

  • Campbell Hausfeld IFN35650 - page 22

    Cómo usar la Clavadora (Continuación) Para colocarle los sellos Cada vez que repare una clavadora deberá limpiarle y lubricarle las partes internas. Le recomendamos que use Parker O-lube o un lubricante equivalente en todos los anillos en O. A cada anillo en O se le debe dar un baño de lubricante para anillos antes de instalarlos. Igualmente, d ...

  • Campbell Hausfeld IFN35650 - page 23

    Modelo IFN35650 Manual de Instrucciones 23 Sp Garantía Limitada 1. DURACIÓN: Desde la fecha de compra por parte del comprador original, según se detalla: 1 (un) año. 2. QUIEN OTORGA ESTA GARANTIA (EL GARANTE: Campbell Hausfeld / The Scott Fetzer Company 100 Production Drive, Harrison, Ohio 45030 Teléfono: (800) 543-6400 3. QUIEN RECIBE ESTA GA ...

  • Campbell Hausfeld IFN35650 - page 24

    24 Sp Modelo IFN35650 Manual de Instrucciones Notas ...

Manufacturer Campbell Hausfeld Category Nail Gun

Documents that we receive from a manufacturer of a Campbell Hausfeld IFN35650 can be divided into several groups. They are, among others:
- Campbell Hausfeld technical drawings
- IFN35650 manuals
- Campbell Hausfeld product data sheets
- information booklets
- or energy labels Campbell Hausfeld IFN35650
All of them are important, but the most important information from the point of view of use of the device are in the user manual Campbell Hausfeld IFN35650.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Campbell Hausfeld IFN35650, service manual, brief instructions and user manuals Campbell Hausfeld IFN35650. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Campbell Hausfeld IFN35650.

Similar manuals

A complete manual for the device Campbell Hausfeld IFN35650, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Campbell Hausfeld IFN35650 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Campbell Hausfeld IFN35650.

A complete Campbell Hausfeld manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Campbell Hausfeld IFN35650 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Campbell Hausfeld IFN35650, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Campbell Hausfeld IFN35650, that we can find in the current document
3. Tips how to use the basic functions of the device Campbell Hausfeld IFN35650 - which should help us in our first steps of using Campbell Hausfeld IFN35650
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Campbell Hausfeld IFN35650
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Campbell Hausfeld IFN35650 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Campbell Hausfeld IFN35650?

Use the form below

If you did not solve your problem by using a manual Campbell Hausfeld IFN35650, ask a question using the form below. If a user had a similar problem with Campbell Hausfeld IFN35650 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)