English dropdown-ico

Manual Graco 258875

28 pages 5.76 mb
Download

Go to site of 28

Summary
  • Graco 258875 - page 1

    - For por table spra y applicat ions of water-based and oil- based (mineral spirit-type) arc hitectural paint s and coatings only- Models 258870, 258875, 2588 66, and 258863 Maximum W orking Pressure 2000 psi (1 37 bar , 13.7 MP a) IMPORTANT SAFETY INSTRUCTION S Read all warnings and in structions in this manual. Save th ese instructions. ti14773a ...

  • Graco 258875 - page 2

    Table of Contents 2 3A0159E T able of Contents W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Tr u e C o a t ™ Component Identification . . . . . . . . . . . . . . . 6 Tr u e C o a t ™ Plus Component Identificatio n . . . . . . . . . . . 7 Using Electrical Co rds . . . . . . . . . . . . . . . . . . . . . ...

  • Graco 258875 - page 3

    Warnings 3A0159E 3 Wa r n i n g s The f ollowing warnings are f or the setup , use, maintenance , and repair of th is equipment. The e xclamation point sym- bol aler ts you t o a general w ar ning and the hazard symbols ref er to procedure-specifi c risks. When these symbols appear in the body o f this manual, refer back to these W a rn ings. Pr od ...

  • Graco 258875 - page 4

    Warnings 4 3A0159E FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint f umes, in work area can ignite or explode. T o help prev e nt fire and e x plosion: • Spra yer gen erates spa rks. Do not spr a y or flush with flamma ble liquids. • Use only water- based or o il-based (min eral spirit -type) ma teria ls with a flas h point ...

  • Graco 258875 - page 5

    Warnings 3A0159E 5 EQUIPMENT MISUSE HAZARD Misuse can cause death or ser ious injur y . • Alwa ys wear appropriate glov es, e ye protection, and a respir ator or mask when painting. • Do not oper ate or spra y near children. K eep children aw a y from equipment at all times . • Do not o ver reach or stand on an unstab le suppor t. K eep eff e ...

  • Graco 258875 - page 6

    TrueCoat ™ Component Ide ntification 6 3A0159E Tr u e C o a t ™ Component Identification *NO TE: Filter a ssembly is rev erse-th readed. T ur n left (or count er-clockwise) to tighte n, tur n rig ht (or clockwise) to loo sen. ti15479a F E K M R P B D N A G H T S A T rue Coat P ain t Spra yer B Spra yer Hook D T rue Coat Spra y Tip/Guard Assembl ...

  • Graco 258875 - page 7

    TrueCoat ™ Plus Component Ide ntification 3A0159E 7 Tr u e C o a t ™ Plus Component Identification *NO TE: Filter a ssembly is rev erse-th readed. T ur n lef t (or count er-clockwise) to tighten , tur n rig ht (or clockwise) to loo sen. ti15479a D F E K M R P B D N S G J H T A W A T rueCoat Plus Paint Spra yer B Spra yer Hook D T rueCoat Spra y ...

  • Graco 258875 - page 8

    Using Electrical Cords 8 3A0159E Using Electrical Cor ds Gr ounding and Electrical Requirements This 120 V ac spra yer requires a 120 V ac, 60 Hz, 15A circuit with a ground ing receptacle . Ne ver use an outlet that is not gr ounded or an adapt er . Do not use the spray er if the electr ical co rd has a da m- aged gr ound prong. Po w e r C o r d Ex ...

  • Graco 258875 - page 9

    Common Procedures 3A0159E 9 Common Pr ocedures Pressure Relief Pr ocedure 1. Engage tr igger lock. 2. Put control le ver UP to rele ase pressure. Tr i g g e r L o c k Spra y Tip P osition This spra yer comes with rev ersible spra y tips. Tips can be rotated to tw o positions: SPRA Y and UNCLOG. Contr ol Lever P osition Do not opera te or spra y nea ...

  • Graco 258875 - page 10

    Setup 10 3A0159E Setup Overheating Pr otection This spra yer has a b uilt-in protectiv e de vice to prev ent damage fr om ov erheating. The spray er may automati- cally shut do wn after hea vy use. If this happen s, allow the spra yer to cool down f or 20-30 minutes an d resume spra ying. Installing Suction T ube Aim the inlet of the suction tube a ...

  • Graco 258875 - page 11

    Setup 3A0159E 11 Spra yer Setup This spra yer arrives from the f actor y with a small amount of test mater ial in the system. It is impor tant that y ou flush this material or any stora ge fluid from the spra yer bef ore using it. 1. Plug spr ay er into a properly-grounded outlet . 2. Fill material cup with wate r and thread onto spray er . 3. Put ...

  • Graco 258875 - page 12

    Setup 12 3A0159E Materials • When spra ying water-base d mater ials, flush the spra yer thoroughly with water . • When spra ying non-water- based materi als, flush the spra yer thoroughly with mineral spirits or com- patib le, oil- based flushing fluid. Star ting a New Job (o r Refilling the Cup) 1. Engage trigger lock and put control le ver UP ...

  • Graco 258875 - page 13

    Install Tip/ Guard Assembly (if not in stalled) 3A0159E 13 Install Tip/Guar d Assembl y (if not installed) Rever sible Tip Selection Chart 1. Engage trigger lock and put control le ver UP to release pressure in the spra yer . 2. Install filter to Spra y Tip/Guard Assembly . Make sure filter is fully installed into spra yer . NO TE: Filter ass em- b ...

  • Graco 258875 - page 14

    Basic Spraying Techniques 14 3A0159E Basic Spra ying T echniques NO TE: Use a piece of scrap cardboard to pr actice these basic spra ying techniques bef ore yo u begin spra ying the surf ace. Anything y ou don’t want painted that is in the area of your spraying surface shou ld be covered or remo ved. Hold spra yer at least 10 in. (25 cm) from sur ...

  • Graco 258875 - page 15

    Unclogging Spray Tip/Guard Assembly 3A0159E 15 Unc logging Spra y Tip/Guar d Assembl y Occasionally , debris from material can accumulate and clog the spra y tip . P erform the f ollowing steps to unclog the tip . 1. T o unclog tip obstr uction, en gage trig ger lock and pull control le ver UP to release pressure . 2. Re verse spra y tip to UNCLOG ...

  • Graco 258875 - page 16

    Shutdown and Cleaning 16 3A0159E Shutdo wn and Cleaning Flushing Spra yer 1. Engage trigger lock and pull control le ver UP to release pressure . 2. Remo ve mater ial cup and pr operly dispose cup liner or e xcess material. 3. Remo v e and clean spr a yer intak e tube and screen with wat er (or flushing fluid) and a brush e very time you flush the ...

  • Graco 258875 - page 17

    Shutdown and Cleaning 3A0159E 17 7. Discard contaminated fluid and refill with appropri- ate flushing fluid. 8. Disengage trigger loc k, rev erse tip to UNCLOG position, an d pull tr igger for 5 seconds to prepare spra yer . 9. Put control le ver DO WN to spray position. T rigger spra yer into wa ste area until n o paint appears in w ater or flushi ...

  • Graco 258875 - page 18

    Storage 18 3A0159E Cleaning Spra yer Exterior • Wipe paint off outside of spra yer using a sof t cloth moistened with w ater or flushing fluid. Do NO T submerge the spra yer . Tips • Tips will require replac ement depending on abrasiveness of paint. • Do not spra y with worn tip. See T roub leshooting , page 20. Storage 1. Dilute 4 oz. bottle ...

  • Graco 258875 - page 19

    Replacement Parts and Kits 3A0159E 19 Replacement P ar ts and Kits 1 10 4 5 8 13 ti15497a 2 6 12 7 9 14 15 16 17 3 11 11a 11 11a Ref. P ar t Description 1 24E377 Shoulder Strap 2 24F045 Fine Finish Optimizer (with Cleaning T ool) 2-P ack 3 T rueCoat Tip/Guard Assembly NAR311 311 NAR315 315 XWD515 515 XWD517 517 4 24F078 Storage Case 5 Tip Filter 24 ...

  • Graco 258875 - page 20

    Troubleshooti ng 20 3A0159E T r oubleshooting Chec k e v er ything in this T roub leshooting T ab le befo re you bring the spra yer to an authoriz ed ser vice center . Prob lem Cause Solution Spra yer makes no sound when trigge r is pulled T rigg er is locked. Disengage trig ger lock. See page 9. Spray er is not receivi ng power . Plug in spray er ...

  • Graco 258875 - page 21

    Troubleshooting 3A0159E 21 Spra y P attern Diagnostics Spra yer spr ays with poor results T ip is par tially clogged See Uncl ogging Tip/Guar d Assembl y , page 15. Tip is not in c orrect position Rotate tip to SPR A Y position. Incorrect tip f or application of material. See Rev ersible T i p Select ion Chart, page 13. Tip filter is par tially clo ...

  • Graco 258875 - page 22

    Troubleshooti ng 22 3A0159E Spra y patter n has dripping: Spra yer is mo ving too slow f or material. Spra yer is too close to targe t surf ace. Holding trigger while changing spra y direction. Incorrect tip f or application of material. Tip is worn or damaged. Mov e spray er faster while spra ying. Mov e sp ra yer awa y from surface (10 in). Relea ...

  • Graco 258875 - page 23

    Alternate Priming Method 3A0159E 23 Alternate Priming Method 1. Engage tr igger lock and put p rim e/relief valve UP to release pressure . 2. Remov e mater ial cup and f ill with flushing material. 3. With spray er in p rime mo de, turn spra yer upside-do wn, remov e strainer and slowly pour flushing mater ial in to the intake tube until full. 4. H ...

  • Graco 258875 - page 24

    Inlet Valve Cleaning 24 3A0159E Inlet V alve Cleaning Re m ova l 1. Engage trigger lock and pull relief v alve UP to release pressure . 2. Remove material cup and suctio n tube. 3. Hold spra yer upside-do wn and use wrench or sock et to loosen and rem ov e in let fitting, inlet valv e, and spring. NO TE: Make sure the spring also comes out. Use nee ...

  • Graco 258875 - page 25

    Technical Data 3A0159E 25 Te c h n i c a l D a t a Spray er: Maximum w orking pressure 2000 psi (137.8 bar , 13.7 MP a) Maximum amper age 4 amps W eight 5.89 lb (2.67 kg) Dimensions: Length 13.25 in. ( 33.6 cm) Width 5.0 in. (12.7 cm) Height 10.75 in. (27 .3 cm) Storage tempera ture r ange ◆❖ 32° to 122° F (0° to 50°C) Operat ing tempera tu ...

  • Graco 258875 - page 26

    Technical Data 26 3A0159E Notes ...

  • Graco 258875 - page 27

    Technical Data 3A0159E 27 Notes ...

  • Graco 258875 - page 28

    All written and visual data con tained in th is document reflects the late st product information availabl e at the time of publica tion. Graco reserves the right to make changes at any time without notice. Original instructions. T his manual contains English. MM 3A0159 Graco Headquarters: Minneapoli s Internationa l Offices: Belgium, China, Japan, ...

Manufacturer Graco Category Paint Sprayer

Documents that we receive from a manufacturer of a Graco 258875 can be divided into several groups. They are, among others:
- Graco technical drawings
- 258875 manuals
- Graco product data sheets
- information booklets
- or energy labels Graco 258875
All of them are important, but the most important information from the point of view of use of the device are in the user manual Graco 258875.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Graco 258875, service manual, brief instructions and user manuals Graco 258875. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Graco 258875.

Similar manuals

A complete manual for the device Graco 258875, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Graco 258875 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Graco 258875.

A complete Graco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Graco 258875 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Graco 258875, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Graco 258875, that we can find in the current document
3. Tips how to use the basic functions of the device Graco 258875 - which should help us in our first steps of using Graco 258875
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Graco 258875
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Graco 258875 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Graco 258875?

Use the form below

If you did not solve your problem by using a manual Graco 258875, ask a question using the form below. If a user had a similar problem with Graco 258875 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)