-
KitchenAid Series KHWG160 - page 1
1 8578898 INST ANT -HOT ® W A TER DISPENSER ® HOME APPLIANCES INST ALLA TION INSTRUCTIONS AND USE AND CARE GUIDE Record your model’ s information Write down the following information about your hot water dispenser to better help you obtain assistance or service if you ever need it. Y ou will need to know your complete model number and serial nu ...
-
KitchenAid Series KHWG160 - page 2
2 HOT W A TER DISPENSER SAFETY T ABLE OF CONTENTS IMPORT ANT : Observe all governing codes and ordinances. Check location where hot water dispenser will be installed. Make sure you have everything necessary for corr ect installation. It is the responsibility of the installer to comply with installation specifications and with state and local plumbi ...
-
KitchenAid Series KHWG160 - page 3
3 Product dimensions and cabinet requirements Location Requirements Faucet requir es a 1-3/8" (3.5 cm) diameter opening in sink or countertop. Faucet can be installed in place of sink spray hose. If faucet is not to be installed in sink spray hose opening, it is recommended that a qualified installer be contacted to drill hole through your typ ...
-
KitchenAid Series KHWG160 - page 4
4 Electrical Requirements A 120-volt, 60 Hz, AC-only 15 or 20 amp fused, grounded electrical supply is requir ed. It is recommended that a separate circuit serving only your hot water dispenser be pr ovided. Use an outlet that cannot be turned on/off by a switch. Recommended ground method This appliance is equipped with a power supply cord having a ...
-
KitchenAid Series KHWG160 - page 5
5 Installing the T ank 1. Position tank vertically beneath faucet so that the longer copper tube from the faucet r eaches the easy-connect fitting on top of the tank. 2. Use a pencil to mark on the wall where the top of tank needs to be located. Set tank aside. Mark a second line 2-1/4" (5.7 cm) below the first line. IMPORT ANT : The tank must ...
-
KitchenAid Series KHWG160 - page 6
Complete Installation IMPORT ANT : The hot water dispenser can be damaged if the following steps are not followed. NOTE: Do not plug power supply cord into outlet. 1. T urn T emperature Contr ol counterclockwise to “Off” position. 2. Push down and turn the faucet cap clockwise to open faucet. Hold cap open until water flows from the faucet (abo ...
-
KitchenAid Series KHWG160 - page 7
9. When the hot water dispenser tank is empty , reinstall the tank on the mounting bracket. 10. Reconnect the copper faucet tube and the flexible tube (See “Installing the faucet” steps 5-7). When ready to use the dispenser again, follow “Complete Installation” steps 1-5. Do not turn unit on if tank is empty . Damage to the unit will result ...
-
KitchenAid Series KHWG160 - page 8
8 Before Calling for Service If hot water dispenser does not operate, check these points first: ■ Has circuit br eaker tripped or house fuse blown? ■ Is power supply cord plugged into a gr ounded 3 prong outlet? ■ Is the T emperatur e Control set to the “Off” position? ■ Has the water supply been turned off? ■ Is the electrical outlet ...
-
KitchenAid Series KHWG160 - page 9
9 REQUESTING ASSIST ANCE OR SERVICE If you need assistance or service in U.S.A. Call the KitchenAid Customer Interaction Center toll-free at 1-800-422-1230. Our consultants are available to assist you. When calling, please know the purchase date, and the complete model and serial number of your appliance. This information will help us better respon ...
-
KitchenAid Series KHWG160 - page 10
INST ANT -HOT ® water dispenser W arranty ® 10 8578898 © 2005 KitchenAid Printed in U.S.A. ® T rademark of KitchenAid, U.S.A., KitchenAid Canada licensee in Canada. 11/2005 ® HOME APPLIANCES KITCHENAID® HOT WA TER DISPENSER W ARRANTY ONE YEAR LIMITED WARRANTY ON HOT W A TER DISPENSERS MODELS For one year from the date of pur chase, when this ...
-
KitchenAid Series KHWG160 - page 11
1 8578898 DISTRIBUTEUR D’EA U INST ANT -HOT ® ® APP AREILS MÉNA GERS INSTRUCTIONS D’INST ALLA TION ET GUIDE D’UTILISA TION ET D’ENTRETIEN Enregistr ement des renseignements concernant votre modèle Inscrivez les renseignements suivants à pr opos de votre distributeur d’eau chaude; cela vous aidera à obtenir assistance ou service en c ...
-
KitchenAid Series KHWG160 - page 12
2 SÉCURITÉ DU DISTRIBUTEUR D’EA U CHA UDE T ABLE DES MA TIÈRES IMPORT ANT : Respecter les dispositions de tous les codes et règlements en vigueur . Inspecter l’emplacement d’installation du distributeur d’eau chaude instantané. V eiller à disposer de tout le matériel nécessaire pour une installation corr ecte. C’est à l’install ...
-
KitchenAid Series KHWG160 - page 13
3 Dimensions du produit et dimensions du placar d Emplacement d’installation L ’installation du robinet de puisage nécessite la présence d’un trou de 1-3/8" (3,5 cm) dans le r ebord de l’évier ou sur le plan de travail. Il est possible d’installer le robinet à la place d’une douchette d’évier . Si le robinet ne sera pas inst ...
-
KitchenAid Series KHWG160 - page 14
4 Spécifications électriques On doit disposer d’un circuit 120 volts (CA seulement, 60 Hz), protégé par fusible 15 ou 20 A, avec liaison à la terr e. On recommande que l’appar eil soit alimenté par un circuit indépendant. Utiliser une prise de courant dont l’alimentation ne peut être interr ompue par un commutateur . Méthode recomman ...
-
KitchenAid Series KHWG160 - page 15
5 Installation du chauffe-eau 1. Positionner le chauffe-eau verticalement sous le r obinet de telle manière que le tube flexible en cuivr e le plus long du robinet puisse atteindr e le raccord à connexion rapide sur le sommet du chauffe-eau. 2. Avec un crayon, mar quer sur le mur l’endroit où il faudra placer le sommet du chauffe-eau. Mettr e ...
-
KitchenAid Series KHWG160 - page 16
Achever l’installation IMPORT ANT : Si le processus d’installation décrit n’est pas respecté, le chauf fe-eau peut subir des dommages. NOTE : Ne pas déjà brancher le cordon d’alimentation sur la prise de courant. 1. Placer le bouton du sélecteur de température à la position d’arrêt Off. 2. Appuyer sur le bouton de manœuvre du r o ...
-
KitchenAid Series KHWG160 - page 17
ENTRETIEN DU DISTRIBUTEUR D’EA U CHA UDE Conseils pour l’économie d’énergie et préparation pour une période d’inutilisation. En moyenne, on utilise le distributeur d’eau chaude pour chauffer 7 à 8 tasses d’eau par jour . Ceci suscite la consommation de 19 Kilowattheures d’éner gie par mois; il n’est donc pas nécessaire d’ar ...
-
KitchenAid Series KHWG160 - page 18
8 A vant de demander l’intervention d’un technicien Si le distributeur d’eau chaude ne fonctionne pas, recher cher d’abord les causes suivantes : ■ Disjoncteur ouvert ou fusible grillé? ■ Cordon d’alimentation corr ectement branché sur une prise de courant à trois alvéoles r eliée à la terre? ■ Sélecteur de température à la ...
-
KitchenAid Series KHWG160 - page 19
9 DEMANDE D’ASSIST ANCE OU DE SERVICE Si vous avez besoin d’assistance ou de service aux É.-U. Composez le numéro sans frais du Centr e d’interaction avec la clientèle de KitchenAid au 1-800-422-1230. Nos consultants sont disponibles pour vous aider . Lors de votre appel, veuillez connaître la date d’achat et les numér os au complet de ...
-
KitchenAid Series KHWG160 - page 20
Garantie du distributeur d’eau INST ANT -HOT ® ® 8578898 © 2005 KitchenAid ® Marque de commer ce de KitchenAid, U.S.A., Imprimé aux É.-U. KitchenAid Canada porteur de licence au Canada. 11/2005 ® APP AREILS MÉNA GERS GARANTIE DU DISTRIBUTEUR D'EA U CHA UDE KITCHENAID® GARANTIE LIMITÉE DE UN AN SUR LES MODÈLES DE DISTRIBUTEURS D&ap ...
Do you have a question concerning KitchenAid Series KHWG160?
Use the form below
If you did not solve your problem by using a manual KitchenAid Series KHWG160, ask a question using the form below. If a user had a similar problem with KitchenAid Series KHWG160 it is likely that he will want to share the way to solve it.