English dropdown-ico

Manual IBM EP-8KTA

73 pages 1.68 mb
Download

Go to site of 73

Summary
  • IBM EP-8KTA - page 1

    TRADEMARK All products and company names are trademarks or registered trademarks of their respective holders. These specifications are subject to change without notice. Manual Revision 1.0 June 21, 2000 EP-8KT EP-8KT EP-8KT EP-8KT EP-8KT A A A A A An An An An An AMD Soc AMD Soc AMD Soc AMD Soc AMD Soc k k k k k et et et et et A Pr A Pr A Pr A Pr A ...

  • IBM EP-8KTA - page 2

    EP-8KT A T able of Contents Section 1 Introduction Components Checklist ........................................ 1 - 1 Overview AMD Duron TM & Athlon TM Processors ............. 1 - 2 Accelerated Graphics Port .................................. 1 - 3 Hardware Monitoring .......................................... 1 - 3 EP-8KT A Form-Factor ..... ...

  • IBM EP-8KTA - page 3

    EP-8KT A Defaults Menu ..................................................... 4-22 Supervisor/User Password Setting ..................... 4-23 Exit Selecting ...................................................... 4-24 Appendix Appendix A Memory Map ....................................................... A-1 I/O Map .................................. ...

  • IBM EP-8KTA - page 4

    EP-8KT A Page Left Blank ...

  • IBM EP-8KTA - page 5

    Introduction EP-8KT A Page 1-1 Section 1 INTRODUCTION Components Checklist ü ü ü ü ü A . ( 1 ) EP-8KT A mainboard ü ü ü ü ü B. (1 ) EP-8KT A user  s manual ü ü ü ü ü C. (1 ) Floppy ribbon cable ü ü ü ü ü D. ( 1 ) A T A-66 Hard drive ribbon cable E . ( 1 ) USB Cable (Optional) ü ü ü ü ü F . ( 1 ) Driver and utility A B US ...

  • IBM EP-8KTA - page 6

    Introduction EP-8KT A Page 1-2 Ov er view AMD Duron TM & Athlon TM Processors The AMD Athlon is a seventh-generation micro architecture with an integrated L2 cache, which is powerful enough to support the bandwidth requirements of a large range of applications, hardware, graphics, and memory technologies. These processors implement advanced des ...

  • IBM EP-8KTA - page 7

    Introduction EP-8KT A Page 1-3 The AMD Duron processor is derived from the AMD Athlon processor core. It features full-speed, on-chip cache memory, a 200MHz front side system bus, and enhanced 3DNow! technology. Although both processors are related, there are key differences. The AMD Athlon processor is targeted at the performance segment, and a ...

  • IBM EP-8KTA - page 8

    Introduction EP-8KT A Page 1-4 EP-8KT A For m-Factor The EP-8KT A is designed with A TX form factor - the new industry standard of chassis. A TX form factor is essentially a Baby-A T baseboard rotated 90 degrees within the chassis enclosure and a new mounting configuration for the power supply . With these changes the processor is relocated away fr ...

  • IBM EP-8KTA - page 9

    Introduction EP-8KT A Page 1-5 P ow er-On/Of f (Remote) The EP-8KT A has a single 20-pin connector for A TX power supplies. For A TX power supplies that support the Remote On/Off feature, this should be connected to the systems front panel for system Power On/Off button. The systems power On/Off button should be a momentary button that is normally ...

  • IBM EP-8KTA - page 10

    Introduction EP-8KT A Page 1-6 Figur e 5: System Block Diagram System Block Diagram PA C PCI Bridge and memor y contr oller VT8 363 133/ 100 MHz 133/ 100 MHz 66M Hz 4X AMD Sock et A Processo r s VT82C686A I/O B ri dge AC 97 USB 0,1 USB 2,3 ...

  • IBM EP-8KTA - page 11

    Features EP-8KT A Page 2-1 Section 2 FEA TURES EP-8KT A F eatures:  EP-8KT A is based on the AMD Socket A Processors operating at 600 ~ 1GHz on Socket A.  Designed with VIA KT133 AGPset.  Supports up to 768MB of DRAM (minimum of 32 MB) on board (please see Section 3-2).  EP-8KT A will support Error Checking and Correcting (ECC) when usi ...

  • IBM EP-8KTA - page 12

    Features EP-8KT A Page 2-2  4 USB ports provided, 2 ports are onboard and another 2 USB ports as optional.  Built-in A TX 20-pin power supply connector .  Software power-down when using W indows ® 95/98 or W indows ® 2000.  Supports ring-in feature (remote power-on through external modem, allows system to be turned on remotely).  R ...

  • IBM EP-8KTA - page 13

    Installation EP-8KTA Page 3-1 Section 3 INST ALLA TION ...

  • IBM EP-8KTA - page 14

    Installation EP-8KTA Page 3-2 Figure 1 EP-8KTA Detailed Layout ...

  • IBM EP-8KTA - page 15

    Installation EP-8KTA Page 3-3 Easy Installa tion Pr ocedure The following must be completed before powering on your new system: 3-1. CPU Insertion 3-2. Jumper Settings 3-3. System memory Configuration 3-4. Device Connectors 3-5 External Modem Ring-in Power ON and Keyboard Power ON Functions (KBPO) 3-6. STR Function Section 3-1 CPU Inser tion CPU In ...

  • IBM EP-8KTA - page 16

    Installation EP-8KTA Page 3-4 Step 3 Close the socket by lowering and locking the actuation lever. Figure 4 Figure 5 Step 4 Thermal conductive and qualified heatsink recommended by AMD are must a to avoid CPU overheat and burned. ...

  • IBM EP-8KTA - page 17

    Installation EP-8KTA Page 3-5 Section 3-2 J umper Settings The EP-8KTA motherboard was designed with very few jumpers to make your installation faster and easier. 1234 5 ON 6 SW1: CPU Vcore Voltage Selection 1 W S e r o c V U P C ) V ( 123 4 5 F F OF F OF F OF F ON O0 3 . 1 N OF F OF F OF F ON O5 3 . 1 F F ON OF F OF F ON O0 4 . 1 N ON OF F OF F ON ...

  • IBM EP-8KTA - page 18

    Installation EP-8KTA Page 3-6 JP13 Keyboard Power-ON Function JP13 = 1-2 Disabled (Default) = 2-3 Enabled 1 1 JP3 Power Loss Recovery JP3 = 1-2 Disabled = 2-3 Enabled 1 JP14 CPU Host Clock Select JP14 = 1-2 100MHz = 2-3 133MHz ...

  • IBM EP-8KTA - page 19

    Installation EP-8KTA Page 3-7 Section 3-3 System Memor y Configur ation Memor y Layout The EP-8KTA supports (3) PC133 168-pin DIMMs (Dual In-line Memory Module). The DIMMs is for SDRAM (Synchronous DRAM) only.  DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or 125MHz (8ns) bus speed.  If you use both 50ns and 60ns memory you must configure you ...

  • IBM EP-8KTA - page 20

    Installation EP-8KTA Page 3-8 DIMM Module Installation Figure 3 displays the notch marks and what they should look like on your DIMM memory module. DIMMs have 168-pins and two notches that will match with the onboard DIMM socket. DIMM modules are installed by placing the chip firmly into the socket at a 90 degree angle and pressing straight down (f ...

  • IBM EP-8KTA - page 21

    Installation EP-8KTA Page 3-9 Section 3-4 De vice Connectors Figure 7 J2,J3 : Chassis Panel Connector  Power_LED, Speaker, Reset, Sleep, Turbo LED and HDD LED J4: CPU Fan Power  A plug-in for the CPU Fan Power J5: SYS Fan Power  A plug-in for the Power Supply Fan Power J6: Chassis Fan Power  A plug-in for the chassis Fan Power J7: WOL ( ...

  • IBM EP-8KTA - page 22

    Installation EP-8KTA Page 3-10 AUX1 : Auxiliary Line_IN Connector  Pin1(Left Line_IN), Pin2/Pin3(GND), Pin4(Right Line-IN) MODEM1 : Telephony Connector  Pin1(Audio_in), Pin2/Pin3(GND), Pin4(Mic-out to Modem) USB2: USB port header pins for adding two additional USB ports. # N I Pr o l o c e r i We m a N l a n g i St n e m m o C 1d e Rc c Vr e ...

  • IBM EP-8KTA - page 23

    Installation EP-8KTA Page 3-11 De vice Connectors (continued) (This is connected to the power button on the case. Using the Soft-Off by Pwr-BTTN feature, you can choose either Instant Off (turns system off immediatly), or 4 sec delay (you need to hold the button down for 4 seconds before the system turns off). When the system is in 4 sec delay mode ...

  • IBM EP-8KTA - page 24

    Installation EP-8KTA Page 3-12 Section 3-5 Exter nal Modem Ring-in Power ON and K eyboar d P o wer ON Functions (KBPO) On the basis of bounded functions in I/O chipset, the two serial ports are able to support the External Modem Ring-in Power ON function. Once users connect the external modem to COM1 or COM2, the EP-8KTA mainboard allows users to t ...

  • IBM EP-8KTA - page 25

    Installation EP-8KTA Page 3-13 3-6 STR (Suspend T o RAM) Function The EP-8KTA supports the STR power management state by maintaining the appropriate states on the SDRAM interface signals. The power source must be kept alive to the SDRAM during STR (ACPI S3). Advanced Configuration Power Interface (ACPI) provides more Energy Saving Features for oper ...

  • IBM EP-8KTA - page 26

    Installation EP-8KTA Page 3-14 ACPI Onboards LED Status Indicator Table Status Onboards LED Location Plug in th e ATX Power Core Power ON J3(PW-ON) Green Mode (S1) STR (S3) Shutdown (So ft-OFF ) (S5) LED1 (Red LED) OFF ON ON ON OFF J2 PW_LED OFF ON Blink ing Blinking O FF d. You must push the Power button connected with onboard J3 pin to wake ...

  • IBM EP-8KTA - page 27

    BIOS EP-8KT A Page 4-1 Section 4 AWARD BIOS SETUP Main Menu A ward s ROM BIOS provides a built-in Setup program which allows user to modify the basic system configuration and hardware parameters. The modified data will be stored in a battery-backed CMOS, so that data will be retained even when the power is turned off. In general, the information ...

  • IBM EP-8KTA - page 28

    BIOS EP-8KT A Page 4-2 The menu displays all the major selection items. Select the item you need to reconfigure. The selection is made by moving the cursor (press any direction key ) to the item and pressing the Enter  key . An on-line help message is displayed at the bottom of the screen as the cursor is moved to various items which provides ...

  • IBM EP-8KTA - page 29

    BIOS EP-8KT A Page 4-3 NOTE: If the hard disk Primary Master/Slave and Secondary Master/ Slave are set to Auto, then the hard disk size and model will be auto-detected. NOTE: The Halt On: field is used to determine when to halt the system by the BIOS if an error occurs. NOTE: Floppy 3 Mode support is a mode used to support a special 3.5 dr ...

  • IBM EP-8KTA - page 30

    BIOS EP-8KT A Page 4-4 V irus W arning : During and after the system boots up, any attempt to write to the boot sector or partition table of the hard disk drive will halt the system and an error message will appear. Y ou should then run an anti-virus program to locate the virus. Keep in mind that this feature protects only the boot sector, not the ...

  • IBM EP-8KTA - page 31

    BIOS EP-8KT A Page 4-5 First /Second/Third/Other Boot Device : The BIOS attempts to load the operat- ing system from the devices in the sequence selected in these items. The choice: Floppy, LS120, HDD, SCSI, CDROM, Disabled. Swap Floppy Drive : This will swap your physical drive letters A & B if you are using two floppy disks. The default is Di ...

  • IBM EP-8KTA - page 32

    BIOS EP-8KT A Page 4-6 T ypematic Rate (Chars/Sec) : This is the number of characters that will be repeated by a keyboard press. The default is 6. 6 : 6 characters per second. 8 : 8 characters per second. 10 : 10 characters per second. 12 : 12 characters per second. 15 : 15 characters per second. 20 : 20 characters per second. 24 : 24 characters pe ...

  • IBM EP-8KTA - page 33

    BIOS EP-8KT A Page 4-7 D8000 - DBFFF Shadow : DC000 - DFFFF Shadow : These categories determine whether ROMs from option cards will be copied into RAM. This will be in 16K byte or 32K byte units, and the size will depend on chipset of the option card. Enabled : Optional shadow is enabled. Disabled : Optional shadow is disabled. ...

  • IBM EP-8KTA - page 34

    BIOS EP-8KT A Page 4-8 Bank 0/1, 2/3, 4/5 DRAM Timing : This value in this field is set by the system board manufacturer, depending on whether the board has paged DRAMs or EDO (extended data output) DRAMs. The Choice: Bank 0/1, 2/3, 4/5. SDRAM Cycle length : This setting defines the CAS timing parameter of the SDRAM in terms of clocks. The default ...

  • IBM EP-8KTA - page 35

    BIOS EP-8KT A Page 4-9 Memory Hole : Y ou can reserve this memory area for the use of ISA adaptor ROMs. The default is Disabled. Enabled : This field enables the main memory (15~16MB) to r emap to ISA BUS. Disabled : Normal Setting. Note: If this feature is enabled you will not be able to cache this memory segment. System BIOS Cacheable : This allo ...

  • IBM EP-8KTA - page 36

    BIOS EP-8KT A Page 4-10 K7 CLK_CTL Select : Use this item to specify the clock control for ramp rate. Select default for a defaulted time value, and optimal for optimum time value which depends on different CPU ratio. The choice: Default, Optimal OnChip USB/USB2 : USB Connector (Port 0-1)/(Port 2-3). The choice: Enabled, Disabled. USB Keyboard Supp ...

  • IBM EP-8KTA - page 37

    BIOS EP-8KT A Page 4-11 4-4 Inte g rated P eripher als Figur e 5: Integrated Peripherals Note: If you do not use the Onboard IDE connector, then you will need to set Onboard Primary PCI IDE: Disabled and Onboard Secondary PCI IDE: Disabled Note: The Onboard PCI IDE cable should be equal to or less than 18 inches (45 cm.). OnChip IDE Channel0 : The ...

  • IBM EP-8KTA - page 38

    BIOS EP-8KT A Page 4-12 Primary Master PIO: The default is Auto. Auto : BIOS will automatically detect the Onboard Primary Master PCI IDE HDD Accessing mode. Mode 0~4 : Manually set the IDE Programmed interrupt mode. Primary Slave PIO: The default is Auto. Auto : BIOS will automatically detect the Onboard Primary Slave PCI IDE HDD Accessing mode. M ...

  • IBM EP-8KTA - page 39

    BIOS EP-8KT A Page 4-13 Init Display First: If two video cards are used (1 AGP and 1 PCI) this specifies which one will be the primary display adapter. The default is PCI Slot. PCI Slots : PCI video card will be primary adapter. AGP: AGP video card will be primary adapter. IDE HDD Block Mode : IDE Block Mode allows the controller to access blocks o ...

  • IBM EP-8KTA - page 40

    BIOS EP-8KT A Page 4-14 Onboard Parallel port : This field allows the user to configure the LPT port. The default is 378H / IRQ7. 378H : Enable Onboard LPT port and address is 378H and IRQ7. 278H : Enable Onboard LPT port and address is 278H and IRQ5. 3BCH : Enable Onboard LPT port and address is 3BCH and IRQ7. Disabled : Disable Onboard W inbond C ...

  • IBM EP-8KTA - page 41

    BIOS EP-8KT A Page 4-15 4-5 P o wer Management Setup Choose the POWER MANAGEMENT SETUP in the CMOS SETUP UTILITY to display the following screen. This menu allows the user to modify the power management parameters and IRQ signals. In general, these parameters should not be changed unless it s absolutely necessary . Figur e 6: Power Managem ...

  • IBM EP-8KTA - page 42

    BIOS EP-8KT A Page 4-16 User define : Allows user to define PM Timers parameters to control power saving mode. ACPI Suspend T ype : This item allows you to select S1(POS) or S3(STR) function. The choice: S1(POS), S3(STR). PM controlled by APM : This option shows weather or not you want the Power Management to be controlled the Advanced Power Manage ...

  • IBM EP-8KTA - page 43

    BIOS EP-8KT A Page 4-17 Soft-Off by PWRBTN : Use this to select your soft-off function. The default is Delay 4 sec. Instant Off : T urns off the system instantly . Delay 4 Second : T urns of f the system after a 4 second delay . If momentary press of button, the system will go into Suspend Mode. Press the power botton again to take system out of Su ...

  • IBM EP-8KTA - page 44

    BIOS EP-8KT A Page 4-18 4-6 PNP/PCI Configuration The PNP/PCI configuration program is for the user to modify the PCI/ISA IRQ signals when various PCI/ISA cards are inserted in the PCI or ISA slots. W ARNING: Conflicting IRQ s may cause the system to not find certain devices. Figur e 7: PCI Configuration Setup PNP OS Installed : Do you have a PN ...

  • IBM EP-8KTA - page 45

    BIOS EP-8KT A Page 4-19 Reset Configuration Data : This setting allows you to clear ESCD data. The default is Disabled Disabled : Normal Setting. Enabled : If you have plugged in some Legacy cards to the system and they were recorded into ESCD (Extended System Configuration Data), you can set this field to Enabled in order to clear ESCD. PCI/VGA Pa ...

  • IBM EP-8KTA - page 46

    BIOS EP-8KT A Page 4-20 4-7 PC Health Status Current CPU T emperature : This is the current temperature of the CPU. Current System T emperature: This is the Current temperature of the system. Curr ent CPU F AN Speed : The current CPU fan speed in RPMs. Curr ent Chassis F AN Speed : The current chassis fan speed in RPMs. CPU(V) : The voltage level o ...

  • IBM EP-8KTA - page 47

    BIOS EP-8KT A Page 4-21 4-8 F requency/V oltage Contr ol DRAM Clock : The item will synchronize/asynchronize DRAM operation clock. Host Clock: DRAM has same working clock with CPU host bus. 2/3 Host: DRAM running with lower operation clock. Auto Detect DIMM/PCI Clk : When enabled the motherboard will automatically disable the clock source for a DIM ...

  • IBM EP-8KTA - page 48

    BIOS EP-8KT A Page 4-22 4-9 Defaults Menu Selecting Defaults from the main menu shows you two options which are described below Load Fail-Safe Defaults When you press <Enter> on this item you get a confirmation dialog box with a message similar to: Load Fail-Safe Defaults (Y/N) ? N Pressing Y loads the BIOS default values for the ...

  • IBM EP-8KTA - page 49

    BIOS EP-8KT A Page 4-23 4-10 Super visor/User Passw ord Setting Y ou can set either supervisor or user password, or both of then. The differences between are: supervisor password : can enter and change the options of the setup menus. user password : just can only enter but do not have the right to change th e options of the setup menus. When you se ...

  • IBM EP-8KTA - page 50

    BIOS EP-8KT A Page 4-24 4-11 Exit Selecting Save & Exit Setup Pressing <Enter> on this item asks for confirmation: Save to CMOS and EXIT (Y/N)? Y Pressing Y stores the selections made in the menus in CMOS  a special section of memory that stays on after you turn your system off. The next time you boot your computer, the BIOS conf ...

  • IBM EP-8KTA - page 51

    Appendix A-1 EP-8KT A Appendix A A-1 MEMOR Y MAP Address Range Size Description [00000-7FFFF] 512K Conventional memory [80000-9FBFF] 127K Extended Conventional memory [9FC00-9FFFF] 1 K Extended BIOS data area if PS/2 mouse is installed [A0000-C7FFF] 160K A vailable for Hi DOS memory [C8000-DFFFF] 96 K A vailable for Hi DOS memory and adapter ROMs [ ...

  • IBM EP-8KTA - page 52

    Appendix EP-8KT A A-2 [2F8-2FF] SERIAL port 2. [360-36F] NETWORK ports. [378-37F] P ARALLEL port 1. [3B0-3BF] MONOCHROME & P ARALLEL port adapter . [3C0-3CF] EGA adapter. [3D0-3DF] CGA adapter. [3F0-3F7] FLOPPY DISK controller. [3F8-3FF] SERIAL port 1. A-3 TIMER & DMA CHANNELS MAP TIMER MAP: TIMER Channel 0 System timer interrupt. TIMER Cha ...

  • IBM EP-8KTA - page 53

    Appendix A-3 EP-8KT A 6 FLOPPY DISK (SMC CHIP). 7 P ARALLEL port 1. 8 R TC clock. 9 A vailable. 1 0 A vailable. 11 A vailable. 1 2 PS/2 Mouse. 1 3 MA TH coprocessor . 1 4 Onboard HARD DISK (IDE1) channel. 1 5 Onboard HARD DISK (IDE1) channel. A-5 RT C & CMOS RAM MAP R TC & CMOS: 0 0 Seconds. 0 1 Second alarm. 0 2 Minutes. 0 3 Minutes alarm. ...

  • IBM EP-8KTA - page 54

    Appendix EP-8KT A A-4 1 6 Base memory high byte. 1 7 Extension memory low byte. 1 8 Extension memory high byte. 19-2d 2E-2F 3 0 Reserved for extension memory low byte. 3 1 Reserved for extension memory high byte. 3 2 DA TE CENTUR Y byte. 3 3 INFORMA TION FLAG. 34-3F Reserve. 40-7F Reserved for CHIPSET SETTING DA T A . ...

  • IBM EP-8KTA - page 55

    Appendix B-1 EP-8KT A Appendix B B- 1 POST CODES For BIOS 6.0 Code POST (hex) DESCRIPTION C F h T est CMOS R/W functionality . C 0 h Early chipset initialization: - Disable shadow RAM - Disable L2 cache (socket 7 or below) - Program basic chipset registers C1h Detect memory - Auto-detection of DRAM size, type and ECC. - Auto-detection of L2 cache ( ...

  • IBM EP-8KTA - page 56

    Appendix EP-8KT A B-2 3. Reset keyboard for W inbond 977 series Super I/O chips. 0Ch Reserved 0 Dh Reserved 0E h T est F000h segment shadow to see whether it is R/W- able or not. If test fails, keep beeping the speaker. 0Fh Reserved 10 h Auto detect flash type to load appropriate flash R/W codes into the run time area in F000 for ESCD & DMI sup ...

  • IBM EP-8KTA - page 57

    Appendix B-3 EP-8KT A checksum fails, use default value instead. 3. Prepare BIOS resource map for PCI & PnP use. If ESCD is valid, take into consideration of the ESCD s legacy information. 4. Onboard clock generator initialization. Disable respective clock resource to empty PCI & DIMM slots. 5 . Early PCI initialization: - Enumerate PCI ...

  • IBM EP-8KTA - page 58

    Appendix EP-8KT A B-4 3 4h Reserved 3 5h Reserved 3 6h Reserved 3 7h Reserved 3 8h Reserved 3 9h Reserved 3 Ah Reserved 3 Bh Reserved 3Ch T est 8254 3 Dh Reserved 3E h T est 8259 interrupt mask bits for channel 1. 3Fh Reserved 40 h T est 8259 interrupt mask bits for channel 2. 4 1h Reserved 4 2h Reserved 43 h T est 8259 functionality . 4 4h Reserve ...

  • IBM EP-8KTA - page 59

    Appendix B-5 EP-8KT A 5 1h Reserved 52h T est all memory (clear all extended memory to 0) 5 3h Reserved 5 4h Reserved 55 h Display number of processors (multi-processor platform) 5 6h Reserved 57 h 1. Display PnP logo 2. Early ISA PnP initialization - Assign CSN to every ISA PnP device. 5 8h Reserved 59h Initialize the combined T rend Anti-V irus c ...

  • IBM EP-8KTA - page 60

    Appendix EP-8KT A B-6 6D h 1. Assign resources to all ISA PnP devices. 2. Auto assign ports to onboard COM ports if the corresponding item in Setup is set to AUTO. 6E h Reserved 6F h 1. Initialize floppy controller 2. Set up floppy related fields in 40:hardware. 7 0h Reserved 7 1h Reserved 7 2h Reserved 73h (Optional Feature) Enter A WDFLASH. ...

  • IBM EP-8KTA - page 61

    Appendix B-7 EP-8KT A 84 h Initialize ISA PnP boot devices 85h 1 . USB final Initialization 2. NET PC: Build SYSID structure 3. Switch screen back to text mode 4. Set up ACPI table at top of memory. 5. Invoke ISA adapter ROMs 6. Assign IRQs to PCI devices 7 . Initialize APM 8. Clear noise of IRQs. 8 6h Reserved 8 7h Reserved 8 8h Reserved 8 9h Rese ...

  • IBM EP-8KTA - page 62

    Appendix EP-8KT A B-8 Page Left Blank ...

  • IBM EP-8KTA - page 63

    Appendix C-1 EP-8KT A Appendix C NOTE: The " LOAD Optimized DEFAULTS " function loads the system default data directly from ROM and initializes the associated hardware properly. This function will be necessary when you accept this mainboard, or the system CMOS data is corrupted. LOAD Optimized DEF AUL TS CMOS Setup Utility - Copyright ( C ...

  • IBM EP-8KTA - page 64

    Appendix EP-8KT A C-2 Page Left Blank ...

  • IBM EP-8KTA - page 65

    Appendix EP-8KT A D-1 Appendix D D-1 GHOST 5.1 Quick User’s Guide Installation is very easy . Y ou only need to copy the Ghost5 folder or Ghost.exe to your hard disk. The current market version is for single Client , so the LPT and NetBios portions will not be explained further. Description of Menus Ghost clones and backs up Disk and Partition. I ...

  • IBM EP-8KTA - page 66

    Appendix EP-8KT A D-2 Disk T o Disk (Disk Cloning) 1. Select the location of the Source drive . 2. Select the location of the Destination drive . 3. When cloning a disk or restoring the backup, set the required partition size as shown in the following figure. There are 3 hard disk functions: 1. Disk T o Disk (disk cloning) 2. Disk T o Image (disk b ...

  • IBM EP-8KTA - page 67

    Appendix EP-8KT A D-3 4. Click OK to display the following confirmation screen. Select Y es to start. Disk T o Image (Disk Backup) 1. Select the location of the Source drive. 2. Select the location for storing the backup file. ...

  • IBM EP-8KTA - page 68

    Appendix EP-8KT A D-4 Disk From Image (Restore Backup) 1. Select the Restore file. 2. Select the Destination drive of the disk to be restored. 3. Click OK to display the following confirmation screen. Select Y es to start. ...

  • IBM EP-8KTA - page 69

    Appendix EP-8KT A D-5 3. When restoring disk backup, set the required partition size as shown in the following figure. 4. Click OK to display the following confirmation screen. Select Y es to start. Partition ...

  • IBM EP-8KTA - page 70

    Appendix EP-8KT A D-6 2. Select the first partition to be backed up. This is usually where the operating system and programs are stored. There are 3 partition functions: 1 . Partition T o Partition (partition cloning) 2 . Partition T o Image (partition backup) 3 . Partition From Image (restore partition) Partition T o Partition (Partition Cloning) ...

  • IBM EP-8KTA - page 71

    Appendix EP-8KT A D-7 3. Select the path and file name for storing the backup file. 4. Is the file compressed? There are 3 options: (1 ) No: do not compress data during backup (2 ) Fast: Small volume compression (3) High: high ratio compression. File can be compressed to its minimum, but this requires longer execution time. 5. During confirmation, ...

  • IBM EP-8KTA - page 72

    Appendix EP-8KT A D-8 Partition From Image (Restore Partition) 1. Select the backup file to be restored. 2. Select the source partition. 3. Select the disk to be restored. ...

  • IBM EP-8KTA - page 73

    Appendix EP-8KT A D-9 4. Select the partition to be restored. 5. Select Y es to start restoring. Check This function checks the hard disk or backup file for backup or restoration error due to F A T or track error . ...

Manufacturer IBM Category Computer Hardware

Documents that we receive from a manufacturer of a IBM EP-8KTA can be divided into several groups. They are, among others:
- IBM technical drawings
- EP-8KTA manuals
- IBM product data sheets
- information booklets
- or energy labels IBM EP-8KTA
All of them are important, but the most important information from the point of view of use of the device are in the user manual IBM EP-8KTA.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals IBM EP-8KTA, service manual, brief instructions and user manuals IBM EP-8KTA. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product IBM EP-8KTA.

Similar manuals

A complete manual for the device IBM EP-8KTA, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use IBM EP-8KTA by users. Manuals are usually written by a technical writer, but in a language understandable to all users of IBM EP-8KTA.

A complete IBM manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual IBM EP-8KTA - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the IBM EP-8KTA, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the IBM EP-8KTA, that we can find in the current document
3. Tips how to use the basic functions of the device IBM EP-8KTA - which should help us in our first steps of using IBM EP-8KTA
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with IBM EP-8KTA
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of IBM EP-8KTA in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning IBM EP-8KTA?

Use the form below

If you did not solve your problem by using a manual IBM EP-8KTA, ask a question using the form below. If a user had a similar problem with IBM EP-8KTA it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)