English dropdown-ico

Manual Integra DTR-7

64 pages 2.76 mb
Download

Go to site of 64

Summary
  • Integra DTR-7 - page 1

    A / V Receiv er DTR-7 DTR-6 Instruction Manual Contents Bef or e using Important Safeguards ........................................ 2 Precautions ........................................................ 3 Features ............................................................. 4 Supplied accessories ......................................... 4 Before ...

  • Integra DTR-7 - page 2

    2 1. Read Instructions – All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions – The safety and operating instructions should be retained for future reference. 3. Heed Warnings – All warnings on the appliance and in the op- erating instructions should be adhered to. 4. Follow Instruc ...

  • Integra DTR-7 - page 3

    3 1. Warranty Claim You can find the serial number on the rear panel of this unit. In case of warranty claim, please report this number. 2. Recording Copyright Recording of copyrighted material for other than personal use is il- legal without permission of the copyright holder. 3. AC Fuse The fuse is located inside the chassis and is not user-servi ...

  • Integra DTR-7 - page 4

    4 AM loop antenna x 1 FM antenna x 1 (Connector shape may vary depending on where the unit is purchased.) Remote controller (RC-392M) x1 Batteries (size AA or UM-3) x 2 Memory Preservation This unit does not require memory preservation batteries. A built-in memory power back-up system preserves the contents of the memory during power failures and e ...

  • Integra DTR-7 - page 5

    5 Bef ore operating this unit 3 2 1 30˚ 30˚ Remote control sensor Receiver STANDBY indicator approx. 16 feet Installing the remote controller batteries 1. Remove the battery compartment cover by pressing the tab and lifting up the cover. 2. Insert two AA (R6- or UM-3)-size batteries into the battery compartment. Carefully follow the polarity diag ...

  • Integra DTR-7 - page 6

    6 A udio equipment connections • Do not piug in the power cord until all connections have been made. • On each pair of input jacks, a red connector (marked R) corresponds to the right channel, and a white connector (marked L) to the left channel. • Please refer to the instruction manual of each component when making any con- nections. • Ins ...

  • Integra DTR-7 - page 7

    7 Audio equipment connections AC outlet connection You can connect the power cord from another audio device to the rear of this receiver. Since the AC outlets on the unit are a SWITCHED type outlet, you can use the STANDBY/ON button, to turn on/off the power to both this receiver and the connected audio de- vices. First turn the POWER switch ON ( ) ...

  • Integra DTR-7 - page 8

    8 R V L R L R L R L VIDEO-1 OUT IN VIDEO-2 VIDEO-3 OUT IN IN TAPE VIDEO S VIDEO OSD SELECTOR (REC) OUT IN (PLAY) DIGITAL OUTPUT DIGITAL INPUT COAXIAL 1 COAXIAL 2 OPTICAL 1 OPTICAL 2 OPTICAL FRONT FRONT CENTER SUB WOOFER SURROUND FRONT CENTER CD PHONO SUB WOOFER SURROUND AMP IN PRE OUT GND MONITOR OUT S REMOTE CONTROL REMOTE LOCAL IN DVD L RL R L R ...

  • Integra DTR-7 - page 9

    9 R V L R L R L R L VIDEO-1 OUT IN VIDEO-2 VIDEO-3 OUT IN IN TAPE VIDEO S VIDEO OSD SELECTOR (REC) OUT IN (PLAY) DIGITAL OUTPUT DIGITAL INPUT COAXIAL 1 COAXIAL 2 OPTICAL 1 OPTICAL 2 OPTICAL FRONT FRONT CENTER SUB WOOFER SURROUND FRONT CENTER CD PHONO SUB WOOFER SURROUND AMP IN PRE OUT GND MONITOR OUT S REMOTE CONTROL REMOTE LOCAL IN DVD L RL R L R ...

  • Integra DTR-7 - page 10

    10 Connecting speaker s Speaker placement Ideal speaker placement varies depending on the size of your room and the wall coverings. Here, only typical example of speaker place- ment and recommendations are shown. Speaker systems Left and Right front speakers and Center speaker • Place these three speakers at the same height from the floor. • Pl ...

  • Integra DTR-7 - page 11

    11 R V L R L R L R L VIDEO-1 OUT IN VIDEO-2 VIDEO-3 OUT IN IN TAPE VIDEO S VIDEO OSD SELECTOR (REC) OUT IN (PLAY) DIGITAL OUTPUT DIGITAL INPUT COAXIAL 1 COAXIAL 2 OPTICAL 1 OPTICAL 2 OPTICAL FRONT FRONT CENTER SUB WOOFER SURROUND FRONT CENTER CD PHONO SUB WOOFER SURROUND AMP IN PRE OUT GND MONITOR OUT S REMOTE CONTROL REMOTE LOCAL IN DVD L RL R L R ...

  • Integra DTR-7 - page 12

    12 R V L R L R L R L VIDEO-1 OUT IN VIDEO-2 VIDEO-3 OUT IN IN TAPE VIDEO S VIDEO OSD SELECTOR (REC) OUT IN (PLAY) DIGITAL OUTPUT DIGITAL INPUT COAXIAL 1 COAXIAL 2 OPTICAL 1 OPTICAL 2 OPTICAL FRONT FRONT CENTER SUB WOOFER SURROUND FRONT CENTER CD PHONO SUB WOOFER SURROUND AMP IN PRE OUT GND MONITOR OUT S REMOTE CONTROL REMOTE LOCAL IN DVD L RL R L R ...

  • Integra DTR-7 - page 13

    13 Connecting the po wer Connecting the power • Before you turn on the receiver, confirm that all connections have been made properly. • Turning on this receiver’s power may cause a momentary power surge, which might interfere with other electrical equipment, such as computers. If this happens, use a wall outlet on a differ- ent circuit. 1. P ...

  • Integra DTR-7 - page 14

    14 Making antenna connections Connecting the antenna cable to the 75/300 ohm antenna adapter. (The antenna adapter must be separately ordered.) Connecting the 300 ohm ribbon wire: Loosen the screws and wrap the wire around these screws. Then tighten the screws with a screwdriver. Connecting the coaxial cable: 1. With your fingernail or a small scre ...

  • Integra DTR-7 - page 15

    15 Connecting the included antennas Connecting the FM indoor antenna: The FM indoor antenna is for indoor use only. Extend the antenna and move it in various directions until the clearest signal is received. Fix it with push pins or similar implements in the position that will cause the least amount of distortion. If the reception is not very clear ...

  • Integra DTR-7 - page 16

    16 Using the on-screen displa y Using the OSD (on-screen display) function lets you display each screen on your TV so that you can perform various settings using only the remote controller. How to use the on-screen display 1. Press the OSD MENU button. The on-screen display appears. 2. Press the upper or lower edge of the ENTER/Cursor button to sel ...

  • Integra DTR-7 - page 17

    17 Using the on-screen display *** Menu *** Input Selector Rec Selector Listening Mode Setup Speaker Setup Screen Setup ** Input Selector ** Input = DVD OPTICAL 1 Digital Input Setup Video Assign Setup IntelliVolume Setup Listening Dolby Mode= Pro Logic THX Cinema ** Rec Selector ** •Picture VIDEO =DVD 1,2 •Sound TAPE =DVD VIDEO 1,2 •Digital ...

  • Integra DTR-7 - page 18

    18 MASTER VOLUME STANDBY/ON PHONES VIDEO S VIDEO STAND - BY POWER OFF ON A SPEAKERS B FM AM PHONO C D TAPE VIDEO-1 DVD VIDEO-4 VIDEO-3 VIDEO-2 D O W N U P FM MUTE/ MODE CHARACTER/ MEMORY SP/SYS SETUP SMART SCAN CONTROLLER MODE AUDIO ADJUSTMENT BASS/ TREBLE DISPLAY DSP REC OUT PRESET/MODE ADJ PUSH TO ENTER DOWN TUNING UP THX /DTS SURROUND MODE LISTE ...

  • Integra DTR-7 - page 19

    19 Setting the speaker configuration • Using the on-screen display 1. Press the OSD MENU button. 2. Select “Speaker Setup” and then press the right edge of the ENTER/Cursor button. 3. Select “Config Setup” and then press the right edge of the ENTER/Cursor button. 4. For the DTR-6, go to the next step. For the DTR-7, the display shows “A ...

  • Integra DTR-7 - page 20

    20 PRESET/MODE ADJ PUSH TO ENTER SP/SYS SETUP Setting the speaker distance Setting the distance from each speaker to the listening position (Loudspeaker Position Time Synchronization * ) Select a value that is closest to the actual distance between each speaker and the listening position. Using the SMART SCAN CONTROLLER, you can easily set the spea ...

  • Integra DTR-7 - page 21

    21 2 Using the test tone to adjust the speaker output levels 1. Press the SP/SYS SETUP button repeatedly until “Level Setup?” appears. Press the SMART SCAN CONTROLLER. The display shows “Left.” 2. Rotate clockwise or counterclockwise the SMART SCAN CONTROLLER to adjust the speaker output level. You can adjust the output level of each speake ...

  • Integra DTR-7 - page 22

    22 Setting the bass peak level (Bass Peak Level Manager * DTR-7 only) To prevent damage to your subwoofer, you can set the bass peak level the subwoofer can reproduce. If your system does not include any subwoofer, this will set the bass peak level your Front speakers can reproduce. 1. Press the SP/SYS SETUP button repeatedly until “Bass Peak Set ...

  • Integra DTR-7 - page 23

    23 PRESET/MODE ADJ PUSH TO ENTER PRESET/MODE ADJ PUSH TO ENTER • Using the on-screen display 1. Press the OSD MENU button. 2. Select “Speaker Setup” and then press the right edge of the ENTER/Cursor button. 3. Select “Bass Peak Setup” and then press the right edge of the ENTER/Cursor button. The “Bass Peak Setup” screen appears. Bass ...

  • Integra DTR-7 - page 24

    24 DOWN TUNING UP 1 2 Presetting FM/AM radio stations Tuning in a radio station 1. Press the FM or AM button. 2. Use the TUNING UP/DOWN buttons to change the fre- quency. UP................the frequency increases. DOWN........ the frequency decreases. • The frequency changes in 50 kHz steps in FM and 10 kHz in AM each time you press the TUNING UP ...

  • Integra DTR-7 - page 25

    25 1 2 Presetting FM/AM radio stations Programming radio stations 1. Select the frequency that you want to store in the memory. (See Tuning in a radio station on page 24.) 2. Press the CHARACTER/MEMORY button. “Preset In? ” appears. 3. Press the SMART SCAN CONTROLLER. The “MEMORY” indicator lights up on the display. 4. Select the desired me ...

  • Integra DTR-7 - page 26

    26 Selecting an input sour ce MASTER VOLUME STANDBY/ON PHONES VIDEO AUDIO LR S VIDEO POWER OFF ON A SPEAKERS B FM AM PHONO C D TAPE VIDEO-1 DVD VIDEO-4 VIDEO-3 VIDEO-2 D O W N U P FM MUTE/ MODE CHARACTER/ MEMORY SP/SYS SETUP SMART SCAN CONTROLLER MODE AUDIO ADJUSTMENT BASS/ TREBLE DISPLAY DSP PRESET/MODE ADJ PUSH TO ENTER DOWN TUNING UP THX /DTS SU ...

  • Integra DTR-7 - page 27

    27 ** Input Selector ** Input = DVD OPTICAL 1 Digital Input Setup Video Assign Setup IntelliVolume Setup Listening Dolby Mode= Pro Logic THX Cinema • Selecting an input source using the on-screen display Instead of using the input selector buttons, you can use on-screen display to select the desired input source. 1. Press the OSD MENU button. 2. ...

  • Integra DTR-7 - page 28

    28 Setting the input signal format (Digital Input Setup) The input signal format defaults to “Automatic.” Although you can use this default setting normally, you may change it depending on the input signal format. Ex.) Setting the input signal format for DVD 1. Press the DVD input selector button. 2. Press the DIGITAL/ANALOG button twice to dis ...

  • Integra DTR-7 - page 29

    29 * Digital Input Setup * CD :COAXIAL 1 Automatic DVD :COAXIAL 2 Automatic VIDEO 1 :---- Automatic • Using the on-screen display 1. Press the OSD MENU button. 2. Select “Input Selector” and then press the right edge of the ENTER/Cursor button. 3. Select “Digital Input Setup” and then press the right edge of the ENTER/Cursor button. The ? ...

  • Integra DTR-7 - page 30

    30 Selecting an input source Selecting the speaker system The DTR-7/DTR-6 can connect to two speaker systems. You can switch between the two speaker systems by using the SPEAKERS A and B buttons. Selecting Speaker system A (SPEAKERS A indicator appears.) Press the SPEAKERS A button to turn on or off the speakers con- nected to the FRONT SPEAKERS A, ...

  • Integra DTR-7 - page 31

    31 Selecting an input source Falling asleep with music (Sleep function, remote controller only) You can turn off the power to the DTR-7/DTR-6 automatically after a specified time period. 1. Press the MODE AUDIO button. 2. Press the SLEEP button. The display shows “Sleep 90min,” which means the receiver automatically enters the standby mode afte ...

  • Integra DTR-7 - page 32

    32 Selecting a preset station MASTER VOLUME STANDBY/ON PHONES VIDEO AUDIO LR S VIDEO POWER OFF ON A SPEAKERS B FM AM PHONO C D TAPE VIDEO-1 DVD VIDEO-4 VIDEO-3 VIDEO-2 D O W N U P FM MUTE/ MODE CHARACTER/ MEMORY SP/SYS SETUP SMART SCAN CONTROLLER MODE AUDIO ADJUSTMENT BASS/ TREBLE DISPLAY DSP PRESET/MODE ADJ PUSH TO ENTER DOWN TUNING UP THX /DTS SU ...

  • Integra DTR-7 - page 33

    33 1 3 Pla ying a m ultichannel input sour ce • Using the on-screen display 1. Press the OSD MENU button. 2. Select “Input Selector” and press the right edge of the EN- TER/Cursor button. 3. Press the right or left edge of the ENTER/Cursor button to select “MULTI CH.” Then, press the center of the ENTER/ Cursor button. The “Multi Ch Inp ...

  • Integra DTR-7 - page 34

    34 Using the Listening Modes Listening Modes The DTR-7/DTR-6’s surround sound enables you to enjoy the pres- ence of a movie theater or concert hall in your room. Before using a listening mode, make sure the Speaker Setup param- eters have been set (refer to page 18 ~ 23). Once the parameters have been set, it is not necessary to set them again. ...

  • Integra DTR-7 - page 35

    35 Using the listening modes 1 . Press one of the INPUT SELECTOR buttons to select the desired sound source. MASTER VOLUME STANDBY/ON PHONES VIDEO AUDIO LR S VIDEO POWER OFF ON A SPEAKERS B FM AM PHONO C D TAPE VIDEO-1 DVD VIDEO-4 VIDEO-3 VIDEO-2 D O W N U P FM MUTE/ MODE CHARACTER/ MEMORY SP/SYS SETUP SMART SCAN CONTROLLER MODE AUDIO ADJUSTMENT BA ...

  • Integra DTR-7 - page 36

    36 Using the listening modes Pressing the DSP button and then rotating the SMART SCAN CONTROLLER lets you view all the listening modes. You can se- lect directly from four listening modes. The mode you can select may vary depending on where the unit is purchased. DIRECT : Press this button if you wish to enjoy pure direct sound. STEREO : Press this ...

  • Integra DTR-7 - page 37

    37 Input sources and listening modes The available listening modes vary depending on the input source. The following table shows each input source and the available listening modes. *Available for DTR-6. Using the listening modes • For Dolby Digital only typical input signals are shown here. 3/2ch, for example, means that the source outputs signa ...

  • Integra DTR-7 - page 38

    38 Parameter Re-EQ* LateNight* LFE level* Front Effect* Reflect Level* Reverb Level Room Size Listening mode Stereo(3 Stereo) * Dolby Pro Logic * O THX Cinema O Action/Musical OO O O O Mono Movie OO O O O Orchestra/Unplugged/ * OO O O O Studio-Mix/TV Logic 5ch Stereo * Direct * Dolby Digital * OO O THX Cinema OO O Action/Musical O OOO O O O Mono Mo ...

  • Integra DTR-7 - page 39

    39 Setting the listening mode parameters Listening mode parameters • Re-EQ (Cinema Re-Equalization) Select “ON” or “OFF.” The Re-EQ function is effective except for “5CH STEREO” and “DIRECT.” Re-Equalization takes the edginess or “brightness” out of your home cinema sound, compensating for the fact that sound mixed for theater ...

  • Integra DTR-7 - page 40

    40 Assigning a video sour ce to eac h audio input sour ce Assigning a video source to each audio input source (video Assign Setup) You can assign a video source to audio input sources such as CD. By doing so, you can play a CD or other audio source while showing the assigned video images on the TV. 1. Select the desired audio input source by pressi ...

  • Integra DTR-7 - page 41

    41 Giving a name to each input source You can give a desired name to each input source (DVD, CD, VIDEO 1-4, TAPE). Characters available for name entry A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z ( ) < > [ ] & + - * / = ? ! : ; ’ ” . , 0 1 2 3 4 5 6 7 8 9 _ ( _ space) 1. Selec ...

  • Integra DTR-7 - page 42

    42 Adjusting the output le vel of eac h speaker while listening to it Fine-tuning the output level of each speaker You can fine-tune the output level of each speaker according to your taste. The output levels you set as below will be lost once the unit is in stand-by mode. (The speaker levels you set using the test tone will be restored.) 1. Press ...

  • Integra DTR-7 - page 43

    43 Other setup operations • Using the on-screen display 1. Press the OSD MENU button. 2. Select "Input Selector" and then press the right edge of the ENTER/Cursor button. 3. Select "IntelliVolume Setup" and then press the right edge of the ENTER/Cursor button. The IntelliVolume Setup screen appears. When the cursor is on " ...

  • Integra DTR-7 - page 44

    44 MASTER VOLUME STANDBY/ON PHONES VIDEO AUDIO LR S VIDEO POWER OFF ON A SPEAKERS B FM AM PHONO C D TAPE VIDEO-1 DVD VIDEO-4 VIDEO-3 VIDEO-2 D O W N U P FM MUTE/ MODE CHARACTER/ MEMORY SP/SYS SETUP SMART SCAN CONTROLLER MODE AUDIO ADJUSTMENT BASS/ TREBLE DISPLAY DSP PRESET/MODE ADJ PUSH TO ENTER DOWN TUNING UP THX /DTS SURROUND MODE LISTENING MODE ...

  • Integra DTR-7 - page 45

    45 Adding sound to a video tape You can add CD or MD sound to your video recordings. The following is an example of adding sound to a video recording using the video cassette recorder connected to the VIDEO-1 jacks of the receiver. Let's assume that you will record the images from a video camera connected to the VIDEO-4 VIDEO jack and the soun ...

  • Integra DTR-7 - page 46

    46 Using Multi-Room Remote System Outline of Multi-room Remote System If you connect Onkyo Multi-room Remote System components as shown in the figure below, you can control the components from a sub- room as well as from the room where the DTR-7/DTR-6 is located. The Multi-Room Remote System allows remote operation when the A/V system is mounted in ...

  • Integra DTR-7 - page 47

    47 Enjoying Music and Movies in the Sub-room To control the system in the sub-room 1. Press the POWER ON button on the remote controller. The MULTI SOURCE indicator located below the STNDBY/ ON button on the receiver will light to indicate that the system enters the Multi-Source mode. Note: If you operate the system in the sub-room while a recordin ...

  • Integra DTR-7 - page 48

    48 The initial settings Config Setup All Ch For THX Yes When set to “No” Subwoofer Yes Front Small Center Small Surround Small Distance Setup Left 3.6m/12ft Center 3.6m/12ft Right 3.6m/12ft R-Sur 2.1m/7ft L-Sur 2.1m/7ft Subwoofer 3.6m/12ft Speaker Level (Test tone) Left 0dB Center 0dB Right 0dB R-Sur 0dB L-Sur 0dB Subwoofer 0dB Listening mode L ...

  • Integra DTR-7 - page 49

    49 Using the remote contr oller Overview When you use a remote controller, typically you press one of the MODE buttons that corresponds to the device you wish to control, then press the operation buttons. For example, if you wish to control the receiver from a remote controller, first press the MODE AUDIO button, then press an appropriate operation ...

  • Integra DTR-7 - page 50

    50 Using the remote controller Controlling an Onkyo/Integra CD player Note: First connect an Onkyo/Integra CD player using the z connection. (See page 7.) 1. Press the MODE CD button. 2. Press the desired CD operation button. TRACK : Selecting a track DISC : Selecting a disc in the CD changer : Down :U p : Playback : Stop : Rewind : Fast forward : ...

  • Integra DTR-7 - page 51

    51 Using the remote controller Controlling an Onkyo/Integra MD recorder Note: Make sure that you point the transmission part on the remote con- troller toward the sensor area on the MD recorder. 1. Press the MODE MD/AUX button. 2. Press the desired MD operation button. Turning the power on and off to the MD recorder POWER ON/STNBY : Turning on or s ...

  • Integra DTR-7 - page 52

    52 Pr ogramming the remote contr oller codes of other de vices into the RC-392M The RC-392M has two learning functions. One is a normal learning function that enables the RC-392M to learn other remote controllers’ codes. The other is a macro learning function, which enables the RC-392M to learn a series of codes already memorized in the remote co ...

  • Integra DTR-7 - page 53

    53 Programming the remote controller codes of other devices into the RC-392M See page 57 for information on how to erase the learned codes from all buttons. Erasing a learned code You can erase a learned code. You cannot erase preset codes. • Erasing a code programmed in a button 1. Press and hold down the corresponding MODE button and press the ...

  • Integra DTR-7 - page 54

    54 Using a Macr o function What is a Macro function? A Macro function enables you to program a series of button operations into a single button on the remote controller. For example, you need to follow the steps below to play a CD player connected to the receiver without using the Macro function: 1: Press the MODE AUDIO button. → 2: Press the POW ...

  • Integra DTR-7 - page 55

    55 Using a Macro function Macro Direct Learning function A series of remote controller button operations can be memorized into the MACRO DIRECT button for one-touch control. Note: You can program only one series of button operations into the MACRO DIRECT button. 1. Press and hold down any one of the eight MODE buttons and press the MACRO DIRECT but ...

  • Integra DTR-7 - page 56

    56 Erasing a learned remote controller button operation from the MACRO MODE buttons 1. Press and hold down the corresponding MODE button and press the MACRO MODE button, then release the buttons. When you press the MODE button, the SEND/LEARN indica- tor lights up. When you press the MACRO MODE button, the indicator turns off. When you release the ...

  • Integra DTR-7 - page 57

    57 Erasing all codes and operations programmed in the buttons This procedure will erase all remote controller codes for the other devices and all macro operations that have been programmed in the RC-392M (see pages 52, 54 and 55). 1. Open the battery cover and remove the batteries. 2. While pressing and holding down the POWER ON button and the POWE ...

  • Integra DTR-7 - page 58

    58 T r oubleshooting guide If a problem occurs while you are using the remote controller, first try to operate the front panel controls on the main unit to make sure that it is not due to a malfunction (or worn out batteries) in the remote controller. Trouble POWER Power shut off immedi- ately after power on. No power. Power on but no sound. The so ...

  • Integra DTR-7 - page 59

    59 Also refer to the respective instruction manuals of the video disc player, video cassette recorder, TV monitor, etc., that compose your entertainment system. Because the unit contains a microcomputer to provide advanced functions, it may malfunction due to external noise or static electricity. If this happens, press the POWER switch on the unit ...

  • Integra DTR-7 - page 60

    60 Specifications DTR-7 AMPLIFIER SECTION Continuous Average Power output (FTC) All channels: 105 watts per channel min. RMS at 8 ohms, 2 channels driven from 20 Hz to 20 kHz with no more than 0.08% total harmonic distortion. 135 watts min. RMS at 6 ohms, 2 channels driven from 1 kHz with no more than 0.1% total harmonic dis- tortion. Total Harmoni ...

  • Integra DTR-7 - page 61

    61 Specifications DTR-7 TUNER SECTION FM Tuning Range: 87.5 - 108.0 MHz (50 kHz steps) Usable Sensitivity Mono: 11.2 dBf, 1.0 µ V (75 ohms IHF) Stereo: 17.2 dBf, 2.0 µ V (75 ohms IHF) 50 dB Quieting Sensitivity Mono: 17.2 dBf, 2.0 µ V (75 ohms) Stereo: 37.2 dBf, 20 µ V (75 ohms) Capture Ratio: 2.0 dB Image Rejection Ratio 40 dB IF Rejection Rat ...

  • Integra DTR-7 - page 62

    62 Front panel For more information about buttons or knobs, refer to the pages listed in the brackets ( [ ] ) below. 1. STANDBY indicator [5, 13] 2. STANDBY/ON button[13] 3. POWER switch [13] 4. SPEAKERS A/B button [26, 30] 5. DISPLAY button [23, 30, 47] 6. DIMMER button [26] 7. Display (Refer to the “Display” illustration.) 8. LISTENING MODE b ...

  • Integra DTR-7 - page 63

    63 Control positions and names 5 7 11 12 10 9 8 13 6 21 19 20 16 15 14 17 18 2 3 1 4 22 Remote controller Using the remote controller, you can control a CD player or cas- sette tape deck connected to the connector of the DTR-7/6. (See page 7 for more information.) 1. SEND/LEARN indicator [49, 52, 53] 2. POWER ON/STNBY button [13, 49, 50, 54, 57] Po ...

  • Integra DTR-7 - page 64

    E SN 29342732 Printed in Japan D9907-1 ONKYO U.S.A. CORPORATION 200 Williams Drive, Ramesy, N.J. 07446, U.S.A. Tel: 201-825-7950 Fax: 201-825-8150 E-mail: integra@onkyousa.com ...

Manufacturer Integra Category Stereo Receiver

Documents that we receive from a manufacturer of a Integra DTR-7 can be divided into several groups. They are, among others:
- Integra technical drawings
- DTR-7 manuals
- Integra product data sheets
- information booklets
- or energy labels Integra DTR-7
All of them are important, but the most important information from the point of view of use of the device are in the user manual Integra DTR-7.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Integra DTR-7, service manual, brief instructions and user manuals Integra DTR-7. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Integra DTR-7.

Similar manuals

A complete manual for the device Integra DTR-7, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Integra DTR-7 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Integra DTR-7.

A complete Integra manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Integra DTR-7 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Integra DTR-7, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Integra DTR-7, that we can find in the current document
3. Tips how to use the basic functions of the device Integra DTR-7 - which should help us in our first steps of using Integra DTR-7
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Integra DTR-7
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Integra DTR-7 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Integra DTR-7?

Use the form below

If you did not solve your problem by using a manual Integra DTR-7, ask a question using the form below. If a user had a similar problem with Integra DTR-7 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)