English dropdown-ico

Manual JVC RX-DP20VBK

90 pages 2.59 mb
Download

Go to site of 90

Summary
  • JVC RX-DP20VBK - page 1

    INSTR UCTIONS AUDIO/VIDEO CONTROL RECEIVER RX-DP20V STANDBY/ON STANDBY PHONES DIMMER CC CONVERTER ZONE 1 ON/OFF ZONE 2 ON/OFF DOOR UP DOOR DOWN MASTER VOLUME S-VIDEO DIGITAL VIDEO L—AUDIO—R VIDEO CHANNEL TV/VIDEO MUTING DVD ON/OFF ON/OFF STANDBY/ON STANDBY/ON STANDBY TV/CATV/DBS VCR 1 ON DVD MULTI CD CDR PHONO TAPE/MD EXT 7.1CH ANALOG/DIGITAL C ...

  • JVC RX-DP20VBK - page 2

    G-1 W arnings, Cautions and Others CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, covers or cabinet. 2. Do not expose this appliance to rain or moisture. Caution –– (STANDBY/ON) switch! Disconnect the mains plug to shut the power off completely. The (STANDBY/ON) switch in any position does not discon- nect ...

  • JVC RX-DP20VBK - page 3

    G-2 Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Fo ...

  • JVC RX-DP20VBK - page 4

    1 Intr oduction W e would like to thank you for purchasing one of our JVC products. Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit, and retain this manual for future reference. Featur es THX Ultra2 cer tified The newly intr oduced THX Ultra2 standard ensures the highest s ...

  • JVC RX-DP20VBK - page 5

    2 T able of Contents Parts Identification ...................................... 3 Getting Started ........................................... 7 Before Installation ...................................................................... 7 Checking the Supplied Accessories ........................................... 7 Connecting the FM and AM Antenna ...

  • JVC RX-DP20VBK - page 6

    3 o a ; d g f s j l k z STANDBY/ ON STANDBY SPEAKERS 1 PHONES AUDIO/VIDEO CONTROL RECEIVER SURROUND THX RIGHT / PRESET 5 EXIT / FM MODE LEFT / PRESET ∞ UP / TUNING 5 SET / MEMORY DOWN / TUNING ∞ SURR/DSP OFF SPEAKER 2 / ZONE 2 INPUT MODE / INPUT ATT ZONE 2 CONTROL EX/ES/7.1 DSP ANALOG DIRECT ADJUST MENU SETUP MENU DIMMER CC CONVERTER ZONE 1 ON/ ...

  • JVC RX-DP20VBK - page 7

    4 Display W indow 1 DU AL indicator (24) • Lights up when Dual Mono signals are detected. 2 ANALOG indicator (26) • Lights up when an analog input (source) is selected. 3 DGTL A UTO indicator (26) • Lights up when auto digital input (DIGIT AL A UTO) is selected. 4 96/24 indicator (52) • Lights up when DTS 96/24 signals are detected. 5 Surro ...

  • JVC RX-DP20VBK - page 8

    5 Rear Panel 9 COMPU LINK-4 (SYNCHR O) ter minals (61, 63) p A V COMPU LINK-III terminals (68) q TEXT COMPU LINK terminals (63) w IR OUT terminal (18, 68) e CTRL OUT +12V terminal • This terminal is only for service use. r IR IN terminal • This terminal is only for service use. t A C IN socket (18) y DIGIT AL OUT terminal (16) u PREOUT jacks (1 ...

  • JVC RX-DP20VBK - page 9

    6 Remote Contr ol 7 SOUND button (39, 50, 56, 59, 71) 8 TEST button (39, 71) 9 CC CONVER TER button (27, 71) p THX button (57, 71) q SURROUND b utton (56, 57, 71) w EX/ES/7.1 button (55, 71) e SLEEP button (28) r Operating buttons f or audio/video components (72–76, 79, 80) t On-screen operation b uttons (36, 46, 64) • SETUP MENU, ADJUST MENU, ...

  • JVC RX-DP20VBK - page 10

    7 Getting Star ted This section explains how to connect audio/video components and speakers to the receiver , and how to connect the power supply . Before Installation General • Be sure your hands are dry . • T ur n the po wer off on all components. • Read the manuals supplied with the components you are going to connect. Location • Install ...

  • JVC RX-DP20VBK - page 11

    8 AM Antenna Connections Connecting the Speakers For full enjoyment of the THX modes (see page 51), it is recommended to use THX-certif ied speakers. Y ou can connect the follo wing speakers: • T wo pairs of front speakers to produce normal stereo sound. • One pair of surround speakers to produce a three-dimensional sound mov ement and en viron ...

  • JVC RX-DP20VBK - page 12

    9 IMPORT ANT: After connecting the speakers, set the speaker setting infor mation properly: • T o obtain the best possible Surround/THX/DSP ef fect in Zone 1, see “Basic Settings” on pages 35 to 44. • T o connect the speakers to the FR ONT 2/ZONE 2 SPEAKERS terminals, set the speaker usage correctly . (See “ w Setting the Zone 2/Speakers ...

  • JVC RX-DP20VBK - page 13

    10 Enhance your audio system Y ou can use this recei ver as the pre-amplif ier (control amplifier) when you connect power amplif iers to the PREOUT jacks on the rear panel, using cables with RCA pin plugs (not supplied). • Connect the white plug to the audio left jack, and the red plug to the audio right jack. Rear view About the FRONT 2/ZONE 2 S ...

  • JVC RX-DP20VBK - page 14

    11 RIGHT MM LEFT PHONO CD CDR T APE MD OUT (REC) IN (PLA Y) OUT (REC) AUDIO MC IN IN R L Connecting Audio/V ideo Components When connecting individual components, refer also to the manuals supplied with them. Analog Connections A udio component connections Use the cables with RCA pin plugs (not supplied). • Connect the white plug to the audio lef ...

  • JVC RX-DP20VBK - page 15

    12 External 7.1-channel output component IMPORT ANT: This receiver is equipped with the following video jacks—composite video, S-video and component video jacks. Y ou can use any of the three to connect a video component However , observe the following points when make connections: • Composite video signals and S-video signals can be con ver te ...

  • JVC RX-DP20VBK - page 16

    13 Notes: • If the VCR has component video output jacks, y ou can connect it to either the COMPONENT 1 IN (D VD), 2 IN, or 3 IN jacks. When connecting the VCR to either one of the component input jacks, make the video input terminal setting correctly . For details, see “ p Setting the Video Input T erminals—VIDEO INPUT ” on page 43. • T o ...

  • JVC RX-DP20VBK - page 17

    14 TV and/or DBS tuner Å To audio output ı To component video input Ç To S-video input Î To composite video input Rear view TV When connecting the TV to the AUDIO jacks (TV SOUND/DBS IN), DO NOT connect the TV’s video output to these video input jacks. DVD IN L R P R 3 IN Y P B P R MONITOR OUT PREOUT SURR BACK SUB WOOFER SURR FRONT ZONE 2 CEN ...

  • JVC RX-DP20VBK - page 18

    15 • When you connect the D VD play er with its analog discrete output (5.1-channel reproduction) jacks: Å To left/right front channel audio output ı To subwoofer (LFE) output Ç To left/right surround channel audio output Î To center channel audio output ‰ To composite video output Ï To S-video output Ì To component video output VIDEO S-V ...

  • JVC RX-DP20VBK - page 19

    16 Digital Connections This receiv er is equipped with six DIGIT AL IN terminals—three digital coaxial terminals and three digital optical terminals—and one DIGIT AL OUT (optical) terminal on the rear . • Another digital optical input terminal is located on the front panel (see page 12). IMPORT ANT: • When connecting the DVD player , digita ...

  • JVC RX-DP20VBK - page 20

    17 Notes: • The signal-reachable distance ma y differ depending on the operating conditions and circumstances. T o improv e transmitting conditions, change the distance to the receiv er and the direction to transmit while operating the remote control. • T o avoid a f ailure in the reception from the remote control, keep the connecting cables an ...

  • JVC RX-DP20VBK - page 21

    18 3. Connect the plug of the transmitter to the IR OUT jack of the recei ver and attach the transmitter . Horizontally: 60˚ V ertically: 60˚ Signal-emitting angle of the transmitter Putting Batteries in the Remote Control Before using the remote control, insert the two supplied batteries first. 1. On the back of the remote contr ol, remov e the ...

  • JVC RX-DP20VBK - page 22

    19 Multi-Room Operations Before operating this receiver any further , be familiar with this multi-room function. This function enables you to listen to different sources in two different places (we call these two places “Zone 1 (main room)” and “Zone 2 (sub-room)”) by using this receiver . This section explains only the required speaker con ...

  • JVC RX-DP20VBK - page 23

    20 Basic Operating Procedur e for Zone 1 On the unit: 1. Press (ST ANDBY/ON). The ST ANDBY lamp goes of f, and the ZONE 1 ON/OFF lamp lights up. The front door mov es down so that the source selecting buttons appear , and the buttons and controls on the unit work for the Zone 1 operations. • For more details, see “T urning the Power On and Of f ...

  • JVC RX-DP20VBK - page 24

    21 Down Up Basic Operating Procedur e for Zone 2 On the unit: 1. Press (ST ANDBY/ON). The ST ANDBY lamp goes of f, and the ZONE 1 ON/OFF lamp lights up. The front door mov es down so that the source selecting buttons appear , and the buttons and controls on the unit work for the Zone 1 operations. • For more details, see “T urning the Power On ...

  • JVC RX-DP20VBK - page 25

    22 Zone 1 (Main Room) Operations This section explains only the operations commonly used when you play any sound source in Zone 1 (main room). See pages 29 to 32 for the Zone 2 (sub-room) operations. • Before performing Zone 1 operations, it is recommended to finish the basic settings on pages 35 to 44. IMPORT ANT: Check the following before or w ...

  • JVC RX-DP20VBK - page 26

    23 Canceling the Zone 1 Operations T o stop Zone 1 operations and sounds from the Zone 1 speakers, press ZONE 1 ON/OFF so that the ZONE 1 ON/OFF lamp goes off. The currently selected front speakers indicator(s) also go(es) of f from the display (no sound will be heard in Zone 1). T o use this recei ver f or Zone 1 operations again, press ZONE 1 ON/ ...

  • JVC RX-DP20VBK - page 27

    24 Selecting different sour ces for picture and sound While watching pictures from a video source (D VD player, VCR, or DBS tuner), you can listen to sound of an audio source. • Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source. Press one of the audio sour ce selecting ...

  • JVC RX-DP20VBK - page 28

    25 Activating the Zone 1 Front Speakers When shipped from the factory , both pairs of the front speakers hav e been set to be used in Zone 1. • T o connect the speakers to the FR ONT 2/ZONE 2 SPEAKERS terminals, set the speaker usage correctly . (See “ w Setting the Zone 2/Speakers 2 Usage—ZONE 2/SPEAKER 2” on page 43.) On the unit ONLY: Wh ...

  • JVC RX-DP20VBK - page 29

    26 Attenuating the Input Signal When the input le vel of the playing source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal lev el to prevent sound distortion. • Y ou have to mak e this setting for analog each source. On the unit ONL Y : Press and hold INPUT A TT (inside the front door) so that t ...

  • JVC RX-DP20VBK - page 30

    27 Changing the Display Brightness Y ou can dim the display . Press DIMMER. • Each time you press the button, the brightness le vel of the display changes as follows: T urning Analog Dir ect On and Off Y ou can enjoy the sound quality closer to the original source by skipping the sound adjustments such as Parametric Equalizer (see page 48) and Mi ...

  • JVC RX-DP20VBK - page 31

    28 T o change the source name to “T APE” or “TV , ” repea t the same procedure above—press and hold T APE/MD to select “T APE, ” or press and hold TV/DBS to select “TV” in step 2. • While selecting “DBS” as the Zone 2 source, you cannot change the source name to “TV . ” Notes: • Once you change the source name , it is ...

  • JVC RX-DP20VBK - page 32

    29 Zone 2 (Sub-r oom) Operations This section explains only the operations used when you play a sound source in Zone 2. See pages 22 to 28 for the Zone 1 operations. • Before performing the Zone 2 operations, it is recommended to finish the basic settings on pages 35 to 44. IMPORT ANT: Check the following before or while using the buttons and con ...

  • JVC RX-DP20VBK - page 33

    30 T o turn off the power (into standb y mode), press (ST ANDBY/ON) again. The ST ANDBY lamp lights up, and the front door automatically closes. (The ZONE 1 ON/ OFF and/or ZONE 2 ON/OFF lamp goes of f.) • A small amount of power is consumed in standby mode. T o turn the po wer off completely , unplug the AC po wer cord. Fr om the remote control: ...

  • JVC RX-DP20VBK - page 34

    31 Selecting the Zone 2 Source to Play Press one of the sour ce selecting buttons. DVD : Selects the D VD player . VCR 1 : Selects the video component connected to the VCR 1 IN jacks. VCR 2 : Selects the video component connected to the VCR 2 IN jacks. TV/DBS : Selects the DBS tuner. • Does not work for selecting TV . VIDEO : Selects the video co ...

  • JVC RX-DP20VBK - page 35

    32 Activating the Zone 2 Front Speakers This section is NO T applicable to those who connect the Zone 2 front speak er s thr ough the ZONE 2 PREOUT jacks through another amplifier (see pag e 19). Bef ore y ou start, remember ... • When shipped from the factory , both pairs of the front speakers hav e been set to be used in Zone 1. T o use the spe ...

  • JVC RX-DP20VBK - page 36

    33 Indicates the functions YOU CAN ALSO USE when the receiv er is ready for Zone 2 operations. Receiving Radio Br oadcasts Y ou can browse through all the stations or use the preset function to go immediately to a par ticular station. T uning in to Stations Manually 1. Press FM/AM. The last receiv ed station of the last selected band is tuned in. ? ...

  • JVC RX-DP20VBK - page 37

    34 2. Press PRESET 5 / ∞ (inside the front door) until y ou find the channel y ou want. Fr om the remote control: 1. Press FM/AM. The last receiv ed station of the last selected band is tuned in. • Each time you press the button, the band alternates between FM and AM. 2. Press the 10 k eys to select a preset channel number . • For channel num ...

  • JVC RX-DP20VBK - page 38

    35 Basic Settings Some of the following settings are required after connecting and positioning your speakers, while others will make operations easier . Basic setting operations are only possible while the receiver is ready for Zone 1 operations. Setup Menu Configuration SETUP MENU (1) SETUP MENU (2) 1 SPEAKER SETTING (See page 38.) 4 SUBWOOFER (Se ...

  • JVC RX-DP20VBK - page 39

    36 Operation through On-Scr een Display Menus T o do the basic settings for this receiver , you can utilize the on- screen display menus in order to finish impor tant settings easily while viewing these menus. Menu operation buttons • When no operation is done for about 1 minute, the on-screen menu (as well as the indications in the unit’ s mai ...

  • JVC RX-DP20VBK - page 40

    37 Menu Operating Procedur e Ex. When setting the speaker distance On the TV scr een 1. Press SETUP MENU . 2. Press fi or % (DO WN or UP) repeatedly to select the desir ed submen u. • In this example, select “SPEAKER DIST ANCE” submenu. 3. Press SET . 4. Set a desired item on the submen u. 1 Press fi or % (DO WN or UP) re peatedly to select ...

  • JVC RX-DP20VBK - page 41

    38 1 Setting the Speakers—SPEAKER SETTING T o obtain the best possible surround sound of the Surround/ THX/DSP modes in Zone 1, you hav e to register the information about the speaker arrangement after all connections are completed. 7 SUBWOOFER Register whether you ha ve connected a subwoofer . YES : Select when a subwoofer is connected. NO : Sel ...

  • JVC RX-DP20VBK - page 42

    39 7 TEST TONE Y ou can emit the test tone to adjust the speaker output le vel. CA UTION: The test tone is automatically fixed to 0 dB, but this level will be louder than you would expect. Select one of the follo wing. • The test tone will be heard for about three seconds after you select “ A UTO” or “MANU AL. ” AU T O : When this is sele ...

  • JVC RX-DP20VBK - page 43

    40 4 Setting the Bass Sounds—SUBWOOFER On this submenu, you can adjust subwoofer and bass sounds precisely according to your preference. 7 SUBWFR OUT Y ou can select the type of the signal which can be transmitted through the subwoofer . In other words, you can determine whether or not the bass elements of the front speaker channels are transmitt ...

  • JVC RX-DP20VBK - page 44

    41 5 Setting the THX Audio—THX AUDIO SETUP These settings are required to obtain the optimum effect from the THX modes. Note: When “SUBWOOFER” is set to “NO” on the SPEAKER SETTING submenu (see page 38), this submenu is not a vailable in the f ollowing cases: – If and “SURR BACK SP” is also set to “NONE, ” or – If “SURR BACK ...

  • JVC RX-DP20VBK - page 45

    42 7 DUAL MONO Select the playback sounds (channel). MAIN : Select to play back the main channel (Ch1).* 1 Signal indicator “L” lights up while playing back this channel. SUB : Select to play back the sub-channel (Ch2).* 1 Signal indicator “R” lights up while playing back this channel. ALL : Select to play back both the main and sub-channel ...

  • JVC RX-DP20VBK - page 46

    43 q T urning On and Off the V ideo Output —VIDEO POWER On this submenu screen, you can turn on or off the po wer supply to the video output circuit built in this unit. 7 VIDEO POWER T urn on or off the po wer suppl y to the video output circuit. ON : Normally select this. Power is supplied to the b uilt-in video output circuit. OFF : Select to c ...

  • JVC RX-DP20VBK - page 47

    44 r Showing the T ext Information on the Display—FL DISPLA Y When you hav e connected an MD recorder or CD player equipped with the TEXT COMPU LINK remote control system (see page 63), you can show te xt information, such as disc title or track title, on the display of this receiv er. 7 FL DISPLA Y T urn on or off the text information display . ...

  • JVC RX-DP20VBK - page 48

    45 Sound Adjustments Sound adjustment operations are only possible while the receiver is ready for Zone 1 operations. Adjustment Menu Configuration ADJUST MENU 1 P ARAMETRIC EQ (See page 48.) 2 MIDNIGHT MODE (See page 49.) 3 EFFECT ADJUST (See page 49.) (When DSP is activated) (When Pro Logic II Music is activated) (When one of the other modes is a ...

  • JVC RX-DP20VBK - page 49

    46 IMPORT ANT: Check the following before or while using the buttons and controls. For Zone 1 operations: The ZONE 1 ON/OFF lamp on the unit is lit. • When using the unit: – “ZONE 2” is not shown in the main display . – Press DOOR DOWN to use the buttons inside the front door . T o close the front door , press DOOR UP . • When using the ...

  • JVC RX-DP20VBK - page 50

    47 Menu Operating Procedur e Ex. When adjusting the DSP effects On the TV scr een 1. Press ADJUST MENU . • Make sure one of the DSP modes except “ ALL CH STEREO” is selected. 2. Press fi or % (DO WN or UP) repeatedly to select the desir ed submen u. • In this example, select “EFFECT ADJUST” submenu. 3. Press SET . 4. Set a desired item ...

  • JVC RX-DP20VBK - page 51

    48 7 Submenu items On this submenu, you can adjust the following items for each channel: BASS FREQ * : Select the center frequency to adjust bass sounds from—63 Hz, 80 Hz, 100 Hz (initial), 125 Hz, 160 Hz, 200 Hz, 250 Hz, 320 Hz, 400 Hz, 500 Hz, 630 Hz, 800 Hz, 1.0 kHz. LEVEL : Adjust the enhancement level f or bass sounds (within the range of +6 ...

  • JVC RX-DP20VBK - page 52

    49 2 Setting the Midnight Mode—MIDNIGHT MODE Using the Midnight mode, you can enjoy a po werful sound at night e ven at a lo w volume lev el. 7 MIDNIGHT MODE Select one of the follo wing: 1: Select when you want to reduce the dynamic range a little. The MIDNIGHT MODE indicator lights up on the display . 2: Select when you want to apply the compre ...

  • JVC RX-DP20VBK - page 53

    50 • When Dolby Pr o Logic II Music is activated: Select and adjust the following items: CENTER EQ: In mo vie theater s, the screen works as the high- frequency cut f ilter of the center channel since the center speakers are located behind the screen and the center channel sounds hav e to pass through the screen. • Select “ ON ” to cut off ...

  • JVC RX-DP20VBK - page 54

    51 Using the Sur r ound and THX Modes This unit activates a variety of Surround and THX modes automatically . The stored basic settings and adjustments performed on the Setup and Adjustment Menus (see pages 35 to 50) are applied. • The following operations are only possible when the receiver is ready for Zone 1 operations, and are used only for Z ...

  • JVC RX-DP20VBK - page 55

    52 Dolby Digital EX Dolby Digital EX (DOLBY D EX) is a ne w digital surround encoding format that adds the third surround channels, called “surround back. ” Compared to the con ventional Dolby Digital 5.1CH, the ne wly added surround back channel can reproduce more detailed mov ements behind you while vie wing the video software. In addition, s ...

  • JVC RX-DP20VBK - page 56

    53 Surr ound and THX Modes Applicable to the V arious Software A v aila ble Surround modes and THX modes vary depending on the speaker settings and the incoming signals. The tables from this page to the next pag e show the relation of the Surround/THX modes and the incoming signals (with the Zone 2 speakers, surround back speakers, and 7.1-channel ...

  • JVC RX-DP20VBK - page 57

    54 Incoming Signal T ype Zone 2 Surround Back Ch ES/EX/7.1 Available Available (multi-channel) Speakers (NONE/1SPK/2SPK) (AUTO/ON/OFF) Surround Mode THX Mode DTS-ES Discrete 6.1ch ON Not av ailable Not av ailable DTS SURR OUND THX CINEMA OFF 2SPK/1SPK AUTO DTS-ES DSCR T THX ES DSCR T ON DTS-ES DSCR T THX ES DSCR T OFF DTS SURR OUND THX CINEMA NONE ...

  • JVC RX-DP20VBK - page 58

    55 Activating the Surr ound and THX Modes Perform the basic settings and adjustments using the Setup and Adjustment Menus first (see pages 35 to 50). Activa ting the Surround mode and the THX mode for a source automatically recalls the memorized settings and adjustments. IMPORT ANT: Check the following before or while using the buttons and controls ...

  • JVC RX-DP20VBK - page 59

    56 Activating the Surr ound Modes For the Surround modes, Parametric Equaliz er adjustments done on the Adjustment menu also take ef fect for the activated speak er channels. • A vailable Surround modes v ary depending on the received signal and the current speaker settings. F or details, see “Sur round and THX Modes Applicable to the V arious ...

  • JVC RX-DP20VBK - page 60

    57 Activating the THX Modes When one of the THX modes is acti vated, P arametric Equalizer and CC Con verter are temporarily canceled. • A vailable THX modes vary depending on the recei ved signal and the current speaker settings. F or details, see “Sur round and THX Modes Applicable to the V arious Software” on pages 53 and 54. 1. Select and ...

  • JVC RX-DP20VBK - page 61

    58 Using the DSP Modes This unit provides a variety of DSP (Digital Signal Processor) modes. The stored basic settings and adjustments performed on the Setup and Adjustment Menus (see pages 35 to 50) are applied. • The following operations are only possible when the receiver is ready for Zone 1 operations, and are used only for the Zone 1 sources ...

  • JVC RX-DP20VBK - page 62

    59 dB L DGTL AUT O DSP DIGITAL SPEAKERS PARAMETRIC EQ MIDNIGHT VOLUME MODE 1 SUBWFR C R LFE RS LS All Channel Stereo mode This mode can reproduce a larger stereo sound f ield using all the connected (and activ ated) speakers. This mode cannot be used without activa ting the surround speakers. • If headphones are connected or if the fr ont speaker ...

  • JVC RX-DP20VBK - page 63

    60 Using the Analog Multi-channel Playback Mode This receiver provides the DVD MUL TI and EXT 7.1CH playback modes for reproducing the analog discrete output mode of the DVD player or another component such as a digital decoder . Before using these playback modes, refer also to the manual supplied for those components. • The following operations ...

  • JVC RX-DP20VBK - page 64

    61 COMPU LINK Remote Contr ol System The COMPU LINK remote control system allows you to operate JVC audio components through this receiver . T o use this remote control system, you need to connect JVC audio components through the COMPU LINK (SYNCHR O) jacks (see below) in addition to the connections using cab les with RCA pin plugs (see page 11). ? ...

  • JVC RX-DP20VBK - page 65

    62 Automatic Power On/Off (Standby): only possible with the COMPU LINK-3 and COMPU LINK-4 connection A utomatic Power On: • When you turn on the r eceiver by pressing (ST ANDBY/ ON) on the unit, or A UDIO (ON) on the remote control with ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector set to “ZONE 1”: OR When you tur n on the Zone 1 sound by pressing ...

  • JVC RX-DP20VBK - page 66

    63 TEXT COMPU LINK Remote Contr ol System The TEXT COMPU LINK remote control system has been developed to deal with the disc information recorded in the CD T ext * and MDs. Using this information in the discs, you can operate the CD player or MD recorder with the TEXT COMPU LINK remote control system through the receiver . FUNCTIONS This remote con ...

  • JVC RX-DP20VBK - page 67

    64 OPERATIONS T o use this remote control system, y ou need to connect the Zone 1 TV to the MONITOR OUT jack (see page 14) and the Zone 2 TV to the ZONE 2 MONITOR OUT jack (see page 19), and set the TV’ s input mode to the proper position to which the receiv er is connected. Make sure y ou have connected the CD player or MD r ecorder equipped wit ...

  • JVC RX-DP20VBK - page 68

    65 Search for a disc by its disc title: 1. Press TEXT DISPLA Y while “CD” is selected as the source. The Disc Information screen appears on the TV . 2. Press % / fi to mo ve to “SEARCH, ” then press SET . The DISC SEARCH screen appears. 3. Press % / fi to mo ve to “DISC TITLE, ” then press SET . The DISC TITLE SEARCH screen appears. 4 ...

  • JVC RX-DP20VBK - page 69

    66 Search for a disc by its genre: 1. Press TEXT DISPLA Y while “CD” is selected as the sour ce. The Disc Information screen appears on the TV . 2. Press % / fi to move to “SEARCH,” then press SET . The DISC SEARCH screen appears. 3. Press % / fi to move to “GENRE, ” then press SET . The GENRE SEARCH screen appears. 4. Press % / fi t ...

  • JVC RX-DP20VBK - page 70

    67 For the MD recorder: Y ou can write the disc information (disc title and song titles) into the disc. Y ou can only write the song title for the song currently selected. • If you have the CD-MD combination deck, you can also enter the disc information (its performer , disc title, and its music genre) of normal audio CDs into the memory built in ...

  • JVC RX-DP20VBK - page 71

    68 A V COMPU LINK Remote Contr ol System This receiver is equipped with the A V COMPU LINK-III. The A V COMPU LINK remote control system allows you to operate JVC video components (TV , VCR, and DVD player) through the receiver . T o use this remote control system, you need to connect the video components you want to operate, following the procedur ...

  • JVC RX-DP20VBK - page 72

    69 The A V COMPU LINK remote control system allows you to use the fi ve basic functions listed below . Remote Control of the TV , DVD player , and VCR Using This Remote Control IMPORT ANT: T o operate the video components using the IR signal transmitter (supplied), place it so that it is aimed at the remote sensor(s) on the target video component(s ...

  • JVC RX-DP20VBK - page 73

    70 One-T ouch DVD Play Simply by starting playback on the D VD player, you can enjoy the D VD playback without setting other switches manually . When you press PLA Y on the remote control supplied for this receiv er for operating the DVD player , the receiver automa tically turns on and changes the Zone 1 sour ce or Zone 2 sour ce , depending on th ...

  • JVC RX-DP20VBK - page 74

    71 Operating JVC’ s Audio/V ideo Components Y ou can operate JVC’s audio and video components with this receiver’ s remote control, since control signals for JVC components are preset in the remote control. Operating Audio Components T uner Y ou can alw ays perfor m the follo wing operations: FM/AM : Tunes in to the last sta tion of the last ...

  • JVC RX-DP20VBK - page 75

    72 CD player After pressing CD, you can perform the following operations on the CD player: PLA Y : Starts playing. 4 : Returns to the beginning of the current (or previous) trac k. ¢ : Skips to the beginning of the next track. STOP : Stops playing. P AUSE : Pauses playing. T o release, press PLA Y . 1 – 10, +10 : Selects a track number directly ...

  • JVC RX-DP20VBK - page 76

    73 Operating V ideo Components IMPORT ANT : T o operate JVC’ s video components using this remote control: • Y ou need to connect JVC’s video components through the A V COMPU LINK jacks (see page 68) in addition to the connections using cables with RCA pin plugs (see pages 13 to 15). • Some JVC VCRs can accept two types of control signals? ...

  • JVC RX-DP20VBK - page 77

    74 Operating Other Manufactur ers’ Equipment Y ou can use this remote contr ol supplied for operating other manufactur ers’ components, either by changing the preset signal codes or by using the learning function (see page 78). Changing the Preset Signal Codes By changing the transmittable signals from preset ones to the other manufacturers’, ...

  • JVC RX-DP20VBK - page 78

    75 T o change the transmittable signals for operating another manufacturer’s CA TV converter and DBS tuner 1. Set the TV operation mode selector to “CA TV/DBS. ” 2. Press and hold TV/CA TV/DBS (ST ANDBY/ON). 3. Press TV/DBS. 4. Enter a manufactur er’ s code using buttons 1–9, and 0. See page 77 to f ind the code. 5. Release TV/CA TV/DBS ( ...

  • JVC RX-DP20VBK - page 79

    76 After pressing D VD MENU, these buttons can be used for the D VD menu operations. Note: Ref er also to the manual supplied for your D VD play er (and the instructions supplied for the discs). 5. T ry to operate y our D VD player by pressing one of the above b uttons. • DO NOT for get to turn on the D VD player before pressing one of the above ...

  • JVC RX-DP20VBK - page 80

    77 Manufactures’ codes for DBS tuner Manufacturer Codes JVC 56, 57 * , 67 Amstrad 43, 44, 45, 46, 47, 48, 49 Blaupunkt 30 Echostar 50, 51, 67 General Instrument 68 Goldstar 31 Grundig 32, 33 Hirshmann 48, 52, 53, 54, 55 ITT/Nokia 34 Kathrein 52, 58, 59, 60, 61, 62, 63 NEC 35, 36 Orbitech 48 Philips 37, 38 RCA 65 Samsung 39, 40 Schwaiger 61, 64 Si ...

  • JVC RX-DP20VBK - page 81

    78 Storing the Remote Signals Manually Y ou can store the signals into the learning buttons by sending the signals you want to store from another remote control. This function is called “Learning Function. ” The learning buttons The highlighted buttons in the illustr ation below are the learning buttons you can store signals into. T o store the ...

  • JVC RX-DP20VBK - page 82

    79 4. Press one of the lear ning buttons, to which y ou want to assign a signal from the target r emote control. The LEARN indicator starts flashing. • If you have pressed DVD or DVD MUL TI in step 3, you can store the signals into the following b uttons: • If you have pressed PHONO in step 3, you can store the signals into the follo wing butto ...

  • JVC RX-DP20VBK - page 83

    80 T o use the stored signals When you want to use the stored signals, follo w the procedure below . 1. Set the LEARN/TRANSMIT (ZONE 1/ZONE 2) selector to “TRANSMIT (ZONE 1/ZONE 2). ” 2. Press one of the sour ce selecting buttons (or CONTROL r epeatedly) to select the desired remote contr ol operation mode (source). 3. Press the desir ed button ...

  • JVC RX-DP20VBK - page 84

    81 T r oubleshooting Use this char t to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC ser vice center . POSSIBLE CAUSE The multi-room function is not set correctly. Speaker signal cables are not connected properly. The SPEAKERS 1 and SPEAKERS 2 buttons are not set correctly. Incorrect source i ...

  • JVC RX-DP20VBK - page 85

    82 SOLUTION Connect an outdoor FM antenna or contact your dealer. (See page 7.) Select a new station. Check with your dealer to be sure you have the correct antenna. Check connections. (See page 7.) Move the antenna farther from automobile traffic. Connect it to the screw marked ( H ). Move speakers away from the turntable. 1. Press (STANDBY/ON) on ...

  • JVC RX-DP20VBK - page 86

    83 Specifications Amplifier Output Po wer At Stereo operation (Analog Direct On): Front channels: 120 W per channel, min. RMS, dri ven into 8 Ω , 20 Hz to 20 kHz with no more than 0.02% total harmonic distortion. 120 W per c hannel, min. RMS, dri ven into 4 Ω , 20 Hz to 20 kHz with no more than 0.07% total harmonic distortion. At Surround opera ...

  • JVC RX-DP20VBK - page 87

    84 V ideo V ideo Input Sensiti vity/Impedance: Composite video: D VD IN, VCR 1 IN, VCR 2 IN, TV SOUND/DBS IN, VIDEO: 1 V(p-p)/75 Ω S-video: D VD IN, VCR 1 IN, VCR 2 IN, TV SOUND/DBS IN, VIDEO: (Y : luminance): 1 V(p-p)/75 Ω (C: chrominance, b urst): 0.286 V(p-p)/75 Ω Component: 1 IN (D VD), 2 IN, 3 IN: (Y : luminance): 1 V(p-p)/75 Ω (P B , ...

  • JVC RX-DP20VBK - page 88

    THIS LIMITED W ARRANTY IS V ALID ONL Y IN THE FIFTY (50) UNITED ST A TES, THE DISTRICT OF COLUMBIA AND IN COMMONWEAL TH OF PUERTO RICO. WHA T WE WILL DO: If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner . Such repair and replacement services shall be rendered by JVC during norma ...

  • JVC RX-DP20VBK - page 89

    BT -51002-5 (0301) QUALITY SER VICE HOW TO LOCA TE YOUR JVC SER VICE CENTER Dear Customer , In order to receive the most satisfaction from your purchase,please read the instruction booklet before operating the unit.In the event that repairs are necessary , please call 1 (800)537-5722 for your nearest authorized servicer or visit our website at www ...

  • JVC RX-DP20VBK - page 90

    VICTOR COMP ANY OF JAP AN , LIMITED 0103NHMMDWJEIN J V C EN © 2003 VICTOR COMPANY OF JAPAN, LIMITED RX-DP20VBK AUDIO/VIDEO CONTROL RECEIVER ...

Manufacturer JVC Category Stereo Receiver

Documents that we receive from a manufacturer of a JVC RX-DP20VBK can be divided into several groups. They are, among others:
- JVC technical drawings
- RX-DP20VBK manuals
- JVC product data sheets
- information booklets
- or energy labels JVC RX-DP20VBK
All of them are important, but the most important information from the point of view of use of the device are in the user manual JVC RX-DP20VBK.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals JVC RX-DP20VBK, service manual, brief instructions and user manuals JVC RX-DP20VBK. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product JVC RX-DP20VBK.

Similar manuals

A complete manual for the device JVC RX-DP20VBK, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use JVC RX-DP20VBK by users. Manuals are usually written by a technical writer, but in a language understandable to all users of JVC RX-DP20VBK.

A complete JVC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual JVC RX-DP20VBK - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the JVC RX-DP20VBK, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the JVC RX-DP20VBK, that we can find in the current document
3. Tips how to use the basic functions of the device JVC RX-DP20VBK - which should help us in our first steps of using JVC RX-DP20VBK
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with JVC RX-DP20VBK
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of JVC RX-DP20VBK in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning JVC RX-DP20VBK?

Use the form below

If you did not solve your problem by using a manual JVC RX-DP20VBK, ask a question using the form below. If a user had a similar problem with JVC RX-DP20VBK it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)