English dropdown-ico

Manual Carrier 48HJ015-025

32 pages 0.66 mb
Download

Go to site of 32

Summary
  • Carrier 48HJ015-025 - page 1

    Installation Instructions CONTENTS Page SAFETY CONSIDERA TIONS ...................1 INST ALLA TION ............................. 1-12 Step 1 — Provide Unit Support ...............1 • ROOF CURB • AL TERNA TE UNIT SUPPOR T Step 2 — Rig and Place Unit ..................3 • POSITIONING • ROOF MOUNT Step 3 — Field Fabricate Ductwork ...... ...

  • Carrier 48HJ015-025 - page 2

    ACCESSOR Y P ACKAGE NO. CURB HEIGHT DESCRIPTION ‘ ‘A ’’ ‘ ‘B’ ’ ‘ ‘C’’ 50PQ900221 1 8 -2 9 (305) Standard Curb — 14 9 High —— — 50PQ900141 2 8 -0 9 (610) Standard Curb for Units Requiring High Installation —— — 50PQ900151 2 8 -0 9 (610) Horizontal Supply and Return Curb 5 8 -6 9 (1676) 0 8 -2 1 ⁄ 2 9 (64) 1 8 ...

  • Carrier 48HJ015-025 - page 3

    AL TERNA TE UNIT SUPPOR T — When the curb cannot be used, install unit on a noncombustible surface. Support unit with sleepers, using unit curb support area. If sleepers cannot be used, support long sides of unit with a minimum of 3 equally spaced 4-in. x 4-in. pads on each side. Step 2 — Rig and Place Unit — Inspect unit for trans- portation ...

  • Carrier 48HJ015-025 - page 4

    T able 1 — Physical Data UNIT SIZE 48 HJD015/HJE015 HJE017 HJD025 208/230, 460 V 575 V OPERA TING WT (lb) Al/Al* 1640/1660 2010 2235 Unit Al/Cu* 1770/1790 2160 2385 Cu/Cu* 1840/1860 2250 2515 Economizer 11 0 11 0 11 0 Roof Curb† 200 200 200 COMPRESSOR 06D Semi-Hermetic Number 12 2 Cylinders 64 6 REFRIGERANT TYPE R-22 Charge (lb) System 1 22.50 ...

  • Carrier 48HJ015-025 - page 5

    UNIT 48HJ MAXIMUM SHIPPING WEIGHT Lb Kg D015 1920 871 E015 1940 880 E017 2310 1048 UNIT 48HJ DIMENSIONS XY Ft-in. mm Ft-in. mm D015 3-2 965 4-0 1219 E015 3-2 965 4-0 1219 E017 3-7 3 ⁄ 8 1 102 3-6 5 ⁄ 8 1083 UNIT 48HJ WEIGHT OF CORNER* ABCD Lb Kg Lb Kg Lb Kg Lb Kg D015 365 166 360 163 373 169 540 245 E015 372 169 363 165 377 171 547 248 E017 509 ...

  • Carrier 48HJ015-025 - page 6

    MAXIMUM SHIPPING WEIGHT Lb Kg 2535 1 150 NOTES: 1. Dimensions in ( ) are in millimeters. 2. Center of gravity . 3. Direction of airflow . 4. Ductwork to be attached to accessory roof curb only . 5. Minimum clearance: a. Rear: 7 8 0 9 (2134) for coil removal. This dimen- sion can be reduced to 4 8 0 9 (1219) if conditions permit coil removal from t ...

  • Carrier 48HJ015-025 - page 7

    Step 3 — Field Fabricate Ductwork — Secure all ducts to building structure. Use flexible duct connectors be- tween unit and ducts as required. Insulate and weatherproof all external ductwork, joints, and roof openings with counter flashing and mastic in accordance with applicable codes. Ducts passing through an unconditioned space must be ins ...

  • Carrier 48HJ015-025 - page 8

    S t e p6—T r a p Condensate Drain — See Fig. 1 1 for drain location. One 3 ⁄ 4 -in. half coupling is provided inside unit evaporator section for condensate drain connec- tion. An 8 1 ⁄ 2 in. x 3 ⁄ 4 -in. diameter and 2-in. x 3 ⁄ 4 -in. diameter pipe nipple, coupled to standard 3 ⁄ 4 -in. diameter elbows, pro- vides a straight path dow ...

  • Carrier 48HJ015-025 - page 9

    Step 8 — Make Electrical Connections FIELD POWER SUPPL Y — Unit is factory wired for volt- age shown on unit nameplate. When installing units, provide a disconnect per NEC (National Electrical Code) of adequate size (T able 2). All field wiring must comply with NEC and local requirements. Route power and ground lines through control box end pa ...

  • Carrier 48HJ015-025 - page 10

    Use the following formula to determine the percent volt- age imbalance. % V oltage Imbalance: = 100 x max voltage deviation from average voltage average voltage EXAMPLE: Supply voltage is 460-3-60. AB =452 v BC =464 v AC =455 v A verage V oltage = 452 +464 +455 3 = 1371 3 = 457 Determine maximum deviation from average voltage: (AB) 457 −452 =5 v ...

  • Carrier 48HJ015-025 - page 11

    5. Loosen sheet metal screws for top cover of base unit located above outdoor-air inlet opening. 6. Match notches in hood top cover with unit top cover screws. Insert hood flange between top cover flange and unit. T ighten screws. 7. Insert outdoor-air inlet screens and spacer in channel created by lower filter retainer and filter support brack ...

  • Carrier 48HJ015-025 - page 12

    ST ART -UP Use the following information and Start-Up Checklist on page CL-1 to check out unit PRIOR to start-up. Unit Preparation — Check that unit has been installed in accordance with these installation instructions and appli- cable codes. Compressor Mounting — Loosen the compressor hold- down bolts until sidewise movement of the washer unde ...

  • Carrier 48HJ015-025 - page 13

    T able 3A — Fan Performance Data, 48HJ015, 208/230, 460-V Units AIRFLOW (CFM) EXTERNAL ST A TIC PRESSURE (in. wg) 0.2 0.4 0.6 0.8 1.0 Rpm W atts Bhp Rpm Watts Bhp Rpm W atts Bhp Rpm W atts Bhp Rpm Watts Bhp 3750 741 510 0.58 854 715 0.82 952 921 1.05 1041 1 130 1.29 1 124 1344 1.53 4000 773 647 0.74 882 859 0.98 978 1071 1.22 1064 1285 1.46 1 145 ...

  • Carrier 48HJ015-025 - page 14

    T able 3B — Fan Performance Data, 48HJ015, 575-V Units AIRFLOW (CFM) EXTERNAL ST A TIC PRESSURE (in. wg) 0.2 0.4 0.6 0.8 1.0 Rpm W atts Bhp Rpm Watts Bhp Rpm W atts Bhp Rpm W atts Bhp Rpm Watts Bhp 3750 741 510 0.58 854 715 0.82 952 921 1.05 1041 1030 1.29 1 124 1344 1.53 4000 773 647 0.74 882 859 0.98 978 1071 1.22 1064 1285 1.46 1 145 1502 1.71 ...

  • Carrier 48HJ015-025 - page 15

    T able 4 — Fan Performance Data, 48HJ017 Units AIRFLOW (CFM) EXTERNAL ST A TIC PRESSURE (in. wg) 0.2 0.4 0.6 0.8 1.0 Rpm W atts Bhp Rpm Watts Bhp Rpm W atts Bhp Rpm W atts Bhp Rpm Watts Bhp 4500 630 805 0.9 741 1059 1.2 846 1341 1.5 945 1653 1.9 1039 1993 2.2 4800 659 943 1.1 765 1208 1.4 865 1497 1.7 961 1816 2.0 1052 2163 2.4 5100 688 1094 1.2 ...

  • Carrier 48HJ015-025 - page 16

    T able 5 — Fan Performance Data, 48HJ025 Units AIRFLOW (CFM) EXTERNAL ST A TIC PRESSURE (in. wg) 0.2 0.4 0.6 0.8 1.0 Rpm W atts Bhp Rpm Watts Bhp Rpm W atts Bhp Rpm W atts Bhp Rpm Watts Bhp 6000 800 1732 1.88 891 2047 2.22 975 2376 2.58 1055 2728 2.96 1 133 3104 3.37 6500 853 2134 2.32 939 2471 2.68 1018 2819 3.06 1094 3185 3.46 1 167 3573 3.88 7 ...

  • Carrier 48HJ015-025 - page 17

    T able 7 — Accessory/FIOP Economizer Static Pressure (in. wg) UNIT 480HJ UNIT VOL T AGE CFM ECONOMIZER PRESSURE DROP 015, 017 All 3,750 .03 4,000 .03 5,000 .05 6,000 .07 7,500 .10 025 All 6,000 .07 7,200 .09 9,000 .1 1 10,000 .12 LEGEND BHP — Brake Horsepower FIOP — Factory-Installed Option NOTES: 1. The factory-assembled horizontal adapter s ...

  • Carrier 48HJ015-025 - page 18

    SERVICE Before performing service or maintenance operations on unit, turn of f main power switch to unit. Electrical shock could cause personal injury. Cleaning — Inspect unit interior at beginning of each heat- ing and cooling season and as operating conditions require. Remove unit top panel and/or side panels for access to unit interior . MAIN ...

  • Carrier 48HJ015-025 - page 19

    F AN SHAFT BEARINGS — For 015 units, the bearings are permanently lubricated. No field lubrication is required. For 017 and 025 units, the bearings are of the pillow block type and have grease fittings. The bearing opposite the motor end has an extended tube line so it can be lubricated from the motor side. Lubricate the bearings twice annually ...

  • Carrier 48HJ015-025 - page 20

    SER VICE AND REPLACEMENT (See Fig. 30) — The 48HJ017,025 units use a fan motor mounting system that features a slide-out motor mounting plate. T o replace or serv- ice the motor , slide out the bracket. 1. Remove the evaporator-fan access panel and the heat- ing control access panel. 2. Remove the center post (located between the evaporator fan a ...

  • Carrier 48HJ015-025 - page 21

    5. Set the outdoor -air thermostat (OA T), located in the econo- mizer section of the unit to 75 F . 6. If the outdoor temperature is below 75 F , the econo- mizer will control the mixed air with the mixed-air sen- sor . If the outdoor air is above 75 F , place a jumper around the contacts of the OA T . 7. Jumper terminal T to terminal T1 on the mo ...

  • Carrier 48HJ015-025 - page 22

    Pilot Adjustment 1. Set system selector switch at OFF position to shut of f unit. T urn of f power to unit. 2. Remove screw cap cover on pilot gas valve to expose adjusting screw (See Fig. 36). 3. T urn valve knobs to pilot position. 4. T urn on power to unit. Set system selector switch to HEA T position and set thermostat to a setting that will ca ...

  • Carrier 48HJ015-025 - page 23

    Main Burners — For most applications, main burners are factory set and should require no adjustment. However , if burner adjustment is necessary: 1. Perform pilot adjustment. 2. T urn gas valve to ON position. Allow unit to operate at least 15 minutes with burner access panel in place. 3. Remove access panel. 4. Loosen primary air shutter (Fig. 3 ...

  • Carrier 48HJ015-025 - page 24

    Fig. 38 — T ypical Wiring Schematic (48HJ025 Shown) 24 ...

  • Carrier 48HJ015-025 - page 25

    Fig. 38 — T ypical Wiring Schematic (48HJ025 Shown) (cont) 25 ...

  • Carrier 48HJ015-025 - page 26

    Fig. 39 — T ypical Component Arrangement (48HJ025 Shown) 26 ...

  • Carrier 48HJ015-025 - page 27

    LEGEND FOR FIG. 38 and 39 AHA — Adjustable Heat Anticipator BKR W/A T — Breaks with Amp T urns C— Contactor , Compressor CB — Circuit Breaker CC — Cooling Compensator CH — Crankcase Heater CLO — Compressor Lockout CLS — Compressor Lockout Switch COMP — Compressor Motor CR — Control Relay CT — Current T ransformer DM — Damper ...

  • Carrier 48HJ015-025 - page 28

    ...

  • Carrier 48HJ015-025 - page 29

    ...

  • Carrier 48HJ015-025 - page 30

    P ACKAGED SERVICE TRAINING Our packaged service training programs provide an excellent way to increase your knowledge of the equipment discussed in this manual. Product programs cover: • Unit Familiarization • Installation Overview • Maintenance • Operating Sequence A large selection of product, theory , and skills programs is available. Al ...

  • Carrier 48HJ015-025 - page 31

    ...

  • Carrier 48HJ015-025 - page 32

    ST ART -UP CHECKLIST MODEL NO.: DA TE: SERIAL NO.: TECHNICIAN: PRE-ST ART -UP: M VERIFY THA T ALL P ACKING MA TERIALS HA VE BEEN REMOVED FROM UNIT M REMOVE ALL SHIPPING HOLDDOWN BOL TS AND BRACKETS PER INSTRUCTIONS M VERIFY INST ALLA TION OF ECONOMIZER HOOD M VERIFY INST ALLA TION OF EXHAUST HOOD M VERIFY THA T CONDENSA TE CONNECTION IS INST ALLED ...

Manufacturer Carrier Category Heating System

Documents that we receive from a manufacturer of a Carrier 48HJ015-025 can be divided into several groups. They are, among others:
- Carrier technical drawings
- 48HJ015-025 manuals
- Carrier product data sheets
- information booklets
- or energy labels Carrier 48HJ015-025
All of them are important, but the most important information from the point of view of use of the device are in the user manual Carrier 48HJ015-025.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Carrier 48HJ015-025, service manual, brief instructions and user manuals Carrier 48HJ015-025. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Carrier 48HJ015-025.

Similar manuals

A complete manual for the device Carrier 48HJ015-025, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Carrier 48HJ015-025 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Carrier 48HJ015-025.

A complete Carrier manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Carrier 48HJ015-025 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Carrier 48HJ015-025, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Carrier 48HJ015-025, that we can find in the current document
3. Tips how to use the basic functions of the device Carrier 48HJ015-025 - which should help us in our first steps of using Carrier 48HJ015-025
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Carrier 48HJ015-025
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Carrier 48HJ015-025 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Carrier 48HJ015-025?

Use the form below

If you did not solve your problem by using a manual Carrier 48HJ015-025, ask a question using the form below. If a user had a similar problem with Carrier 48HJ015-025 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)