English dropdown-ico

Manual BEA LO-21P

13 pages 0.9 mb
Download

Go to site of 13

Summary
  • BEA LO-21P - page 1

    75.5079.08 20061129 Page 1 of 13 PRODUCT DESCRIPTION TECHNICAL SPECIFICATIONS USERS GUIDE LO-21P LOCK OUT RELAY COMPONENT ID SA FET Y PRECAUTIONS The microprocessed LO-21P (PN: 10L O21P) Lock Out Relay is designed to provide a lockout function for the BEA Bodyguard presence sensor, when used with the c omplete Parallax System. The L O-21P uses the ...

  • BEA LO-21P - page 2

    75.5079.08 20061129 Page 2 of 13 ELECTRICAL INSTALLATION – OPTION 1 – STANDARD WIRING STANDARD WIRING WIRE CONNECTIONS Black Motor Input - Red Motor Input + Purple Bodyguard COM. Pin 3 White Bodyguard Data (-) Pin 6 Black / White Activation Sensor COM. Orange Power input / 12-24 VAC/VDC ( - ) Gray Bodyguard N.O. Pin 4 Red / White Bodyguard Data ...

  • BEA LO-21P - page 3

    75.5079.08 20061129 Page 3 of 13 ELECTRICAL INSTALLATION OPTION 2 – Operator Mounte d Switch Wiring diagram below shows how to wire when using an operator-mounted switch to control the flow of voltage from the motor to the lockout module. Switch should be set to close a se t of dry contacts when door is within 2 to 3 degrees of the full open posi ...

  • BEA LO-21P - page 4

    75.5079.08 20061129 Page 4 of 13 ELECTRICAL INSTALLATION Option 3 – Double Pole Double Throw Switch The wiring diagram below shows how to wire a DPDT switch to control the On-Off-Hold function, as well as dat a between the motor and the LO21 P. brown red/white white gray purple orange LO-21P 24 V TRANSFORMER DATA + 7 DATA - 6 N.C. 5 N.O. 4 COM 3 ...

  • BEA LO-21P - page 5

    75.5079.08 20061129 Page 5 of 13 SET-UP INSTRUCTIONS Upon completion of all wiring, proceed with the set-up as follows: 1. Insure that the On-Off-Hold Open switch is in the ON position, and insure that the door control is powered and operating normally. 2. Power the Bodyguar d sensor and, using a BEA Remote Co ntrol, unlock the sens or and change t ...

  • BEA LO-21P - page 6

    75.5079.08 20061129 Page 6 of 13 SETUP INSTRUCTION Cont. DIPSWITCH 6, 7 and 8 OPERATION 7. Adjustment is necessary to configure the dipswitche s to obtain the correct lock out time dela y . To set the dipswitches( 1 through 5) for lock out time, perform the following:  Activate the door to the open position.  Time the overall door closing cyc ...

  • BEA LO-21P - page 7

    75.5079.08 20061129 Page 7 of 13 COMPANY CONTACT TROUBLE- SHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Door will not open – all LED’s are OFF at the LO21P 1. Faulty door control 2. Faulty LO21P 3. Faulty On-Off-Hold Open switch 4. Faulty Eagle 5. Faulty wiring 1. Insure input power is good at LO21P – orange and brown wires. Should be 12 ...

  • BEA LO-21P - page 8

    75.5079.08 20061129 Page 8 of 13 BODYGUARD DK-12 DATA + 7 DATA - 6 N.C. 5 N.O. 4 COM 3 POWER 2 POWER 1 5 N/C 4 N/O 3 COM 2 PWR 1 PWR 24 V TRANSFORMER 1 1 5 V A C SIZE: SHEET: SCALE: A PH: (412) 249-4100 FAX: (412) 249-4101 B.E.A., Inc. 100 Enterprise Drive Pittsburgh, PA 15275 DATE: www.beasensors.c om CAGE CODE: DWG NO: FILE OF: DRAWN BY: REV: 1 O ...

  • BEA LO-21P - page 9

    75.5079.08 20061129 Page 9 of 13 BODYGUARD DK-12 DATA + 7 DATA - 6 N.C. 5 N.O. 4 COM 3 POWER 2 POWER 1 5 N/C 4 N/O 3 COM 2 PWR 1 PWR 24 V TRANSFORMER 1 1 5 V A C HOLD OPEN OFF SIZE: SHEET: SCALE: A PH: (412) 249-4100 FAX: (412) 249-4101 B.E.A., Inc. 100 Enterprise Drive Pittsburgh, PA 15275 DATE: www.beasensors.com CAGE CODE: DWG NO: FILE OF: DRAWN ...

  • BEA LO-21P - page 10

    75.5079.08 20061129 Page 10 of 13 BODYGUARD DK-12 DATA + 7 DATA - 6 N.C. 5 N.O. 4 COM 3 POWER 2 POWER 1 5 N/C 4 N/O 3 COM 2 PWR 1 PWR 24 V TRANSFORMER 1 1 5 V A C SIZE: SHEET: SCALE: A PH: (412) 249-4100 FAX: ( 412) 249-4101 B.E.A., Inc. 100 Enterprise Driv e Pittsburgh, PA 15275 DATE: www.beasensors.com CAGE CODE: DWG NO: FILE OF: DRAWN BY: REV: 1 ...

  • BEA LO-21P - page 11

    75.5079.08 20061129 Page 11 of 13 BODYGUARD DK-12 DATA + 7 DATA - 6 N.C. 5 N.O. 4 COM 3 POWER 2 POWER 1 5 N/C 4 N/O 3 COM 2 PWR 1 PWR 24 V TRANSFORMER 1 1 5 V A C SIZE: SHEET: SCALE: A PH: (412) 249-4100 FAX: (412) 249-4101 B.E.A., Inc. 100 Enterprise Drive Pittsburgh, PA 15275 DATE: www.beasensors.com CAGE CODE: DWG NO: FILE OF: DRAWN BY: REV: 1 O ...

  • BEA LO-21P - page 12

    75.5079.08 20061129 Page 12 of 13 B O D Y G U A R D D K - 1 2 DATA + 7 DATA - 6 N.C. 5 N.O. 4 COM 3 POWER 2 POWER 1 5 N/C 4 N/O 3 COM 2 PWR 1 PWR SIZE: S H E E T : S C A L E : A P H : ( 4 1 2 ) 2 4 9 - 4 1 0 0 F A X : ( 4 1 2 ) 2 4 9 - 4 1 0 1 B . E . A . , I n c . 1 0 0 E n t e r p r i s e D r i v e P i t t s b u r g h , P A 1 5 2 7 5 D A T E : w ...

  • BEA LO-21P - page 13

    75.5079.08 20061129 Page 13 of 13 BODYGUARD DK-12 DATA + 7 DATA - 6 N.C. 5 N.O. 4 COM 3 POWER 2 POWER 1 5 N/C 4 N/O 3 COM 2 PWR 1 PWR SIZE: SHEET: SCALE: A PH: (412) 249-4100 FAX: (412) 249-4101 B.E.A., Inc. 100 Enterprise Drive Pittsburgh, PA 15275 DATE: www.beasensors.com CAGE CODE: DWG NO: FILE OF: DRAWN BY: REV: 1 OF 1 NTS TITLE: BESAM CUP VER. ...

Manufacturer BEA Category Work Light

Documents that we receive from a manufacturer of a BEA LO-21P can be divided into several groups. They are, among others:
- BEA technical drawings
- LO-21P manuals
- BEA product data sheets
- information booklets
- or energy labels BEA LO-21P
All of them are important, but the most important information from the point of view of use of the device are in the user manual BEA LO-21P.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals BEA LO-21P, service manual, brief instructions and user manuals BEA LO-21P. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product BEA LO-21P.

Similar manuals

A complete manual for the device BEA LO-21P, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use BEA LO-21P by users. Manuals are usually written by a technical writer, but in a language understandable to all users of BEA LO-21P.

A complete BEA manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual BEA LO-21P - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the BEA LO-21P, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the BEA LO-21P, that we can find in the current document
3. Tips how to use the basic functions of the device BEA LO-21P - which should help us in our first steps of using BEA LO-21P
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with BEA LO-21P
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of BEA LO-21P in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning BEA LO-21P?

Use the form below

If you did not solve your problem by using a manual BEA LO-21P, ask a question using the form below. If a user had a similar problem with BEA LO-21P it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)