English dropdown-ico

Manual Edelbrock 3562

16 pages 0.92 mb
Download

Go to site of 16

Summary
  • Edelbrock 3562 - page 1

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 1 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 PERFORMER MUL TI-POINT EFI SYSTEMS for TBI-Equipped Chevrolet/GMC T rucks & Suburbans Catalog #s 3562, 3563, 3564, and 3565 INST ALLA TION INSTRUCTIONS ® STOP! BEFORE BEGINNING INST ALLA TION , READ THESE IMPORT ANT NOTES… ❑ Y ou must pur ...

  • Edelbrock 3562 - page 2

    MANIFOLD ASSEMBL Y CONTENTS Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 2 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 Qty . Description ❑ 1 Manifold assembly (see detail below) ❑ 1 Installation instructions ❑ 1 EPROM adapter circuit board (#3562 only) ❑ 1 Fuel injector wiring harness ❑ 1 Fuel filter adapter fitting (filter to ...

  • Edelbrock 3562 - page 3

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 3 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 IMPOR T ANT INSTRUCTIONS For ordering your FREE Edelbrock computer chip. Y ou must use an Edelbrock chip with the Performer Multi-Point EFI conversion ® Y ou must change the computer chip in your stock computer (ECU) for proper functioning and ma ...

  • Edelbrock 3562 - page 4

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 4 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 ® INST ALLA TION INSTRUCTIONS for Performer Multi-Point EFI System for 7.4L TBI-Equipped Chevrolet/GMC Vehicles Catalog #3562 and #3564 for 1987-1990 Model Y ears Catalog #3563 and #3565 for 1991-1995 Model Y ears • APPLICA TION INFORMA TION: P ...

  • Edelbrock 3562 - page 5

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 5 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 INST ALLA TION PROCEDURE 1. Disconnect negative batter y cable. 2. Drain coolant. 3. Remove air cleaner assembly . 4. Label all lines, wires, and connections with masking tape before disassembly to aid in re-assembly . Disconnect all throttle cabl ...

  • Edelbrock 3562 - page 6

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 6 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 10. DISTRIBUTOR REMOV AL Remove plug wires from top of distributor cap. Make note of location of each wire. Remove distributor ca p. Before removal of distributor , note the location of the distributor body and the ignition rotor by marking distri ...

  • Edelbrock 3562 - page 7

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 7 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 13. INT AKE PREPARA TIONS With fuel lines out of the way , scrape remaining intake gaskets off of cylinder heads and scrape both end seals c lean. With surfaces clean, install intake gaskets to cylinder heads. Use GM gaskets #10181398. Apply gaske ...

  • Edelbrock 3562 - page 8

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 8 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 Tighten the manifold bolts following the tightening sequence shown below. T orque to 25 ft. lbs. Install the distributor in the engine. Using your marks as a reference, snug down distributor clamp. NOTE: Final timing will be adjusted after engine ...

  • Edelbrock 3562 - page 9

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 9 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 16. HEA TER HOSE SUPPL Y LINE For all years, the heater core supply will come from the right front water port on intake manifold. Y ou will need to install the 1/2" NPT -to-3/4" hose fitting into manifold using T eflon sealant on threads ...

  • Edelbrock 3562 - page 10

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 10 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 19. FUEL RETURN LINE INST ALLA TION Install the 90° #6 pushlock fitting into the 10-foot length of hose using the pushlock fitting installation procedures described previously . T ape off the open end of fuel line to prevent debris from entering ...

  • Edelbrock 3562 - page 11

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 11 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 Pull rubber grommet off of wires. Force silicone (oxygen sensor - safe) through these four holes, filling them with silicone. Install the grommet on air valve in groove to prevent dirt from entering the system. 23. ELECTRICAL CONNECTION Separate ...

  • Edelbrock 3562 - page 12

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 12 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 installed in manifold). Route hose and cut as necessary to prevent interference with linkage. Tighten both clamps and secure with tie wrap as shown. Tie Wrap Brake Vacuum Hose From Booster to Supply Port 26. THROTTLE BOD Y CONVERSION Remove the f ...

  • Edelbrock 3562 - page 13

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 13 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 Fuel T ank Disconnect two fuel lines, two hoses, and an electrical connection with a ground wire. There is a center fuel pump sending unit assembly lock ring holding assembly into tank. Using a hammer and brass punch, gently strike open edge of l ...

  • Edelbrock 3562 - page 14

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 14 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 Note: The fuel line will be a very tight fit over the 3/8" tubing. It may be necessary to lube the tubing with some spray lubricant to ease hose installation. Slip the 5/16" clamp over the rubber hose, then insert fuel pump barb into ho ...

  • Edelbrock 3562 - page 15

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 15 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 This installation uses a piggyback chip ada pter . Push your new computer chip into the adapter , then install these two parts into ECM. There is an alignment lug so that they only fit one way . Be careful not to bend any pins. Put plate back on ...

  • Edelbrock 3562 - page 16

    Catalog #3562, 3563, 3564, 3565 Rev . 3/06 Page 16 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 Edelbrock Corporation • 2700 California St. • T orrance, CA 90503 EFI T ech-Line: (800) 416-8628, Option 3 • E-Mail: EFIT ech@Edelbrock.com ® BASIC TROUBLESHOOTING 1. Engine Combinations a. If you assemble a combination of parts other than ...

Manufacturer Edelbrock Category Automobile Parts

Documents that we receive from a manufacturer of a Edelbrock 3562 can be divided into several groups. They are, among others:
- Edelbrock technical drawings
- 3562 manuals
- Edelbrock product data sheets
- information booklets
- or energy labels Edelbrock 3562
All of them are important, but the most important information from the point of view of use of the device are in the user manual Edelbrock 3562.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Edelbrock 3562, service manual, brief instructions and user manuals Edelbrock 3562. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Edelbrock 3562.

Similar manuals

A complete manual for the device Edelbrock 3562, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Edelbrock 3562 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Edelbrock 3562.

A complete Edelbrock manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Edelbrock 3562 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Edelbrock 3562, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Edelbrock 3562, that we can find in the current document
3. Tips how to use the basic functions of the device Edelbrock 3562 - which should help us in our first steps of using Edelbrock 3562
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Edelbrock 3562
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Edelbrock 3562 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Edelbrock 3562?

Use the form below

If you did not solve your problem by using a manual Edelbrock 3562, ask a question using the form below. If a user had a similar problem with Edelbrock 3562 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)