English dropdown-ico

Manual GE Monogram ZIR36N LH

40 pages 0.59 mb
Download

Go to site of 40

Summary
  • GE Monogram ZIR36N LH - page 1

    GE Monogram ® 36" Refrigerators and 36" Freezers Custom Options Guide and Installation Instructions With Custom Pas ifimenstions ...

  • GE Monogram ZIR36N LH - page 2

    CAUTION Before you begin – Read these instructions completely and carefully . IMPORT ANT – Save these instructions for local inspector’ s use. IMPORT ANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer – Be sure to leave these instructions with the Consumer . Note to Consumer – Keep these instructions with your Owner’ ...

  • GE Monogram ZIR36N LH - page 3

    3 Design Information 36" Refrigerators, Freezers Flush or Semi-Flush Enclosure Installations Side Panel Requirements: • Side panels are not required whenever the refrigerator is installed into an enclosure or between pantry and oven cabinets. • Side panels are required whenever the sides of the refrigerator are exposed. • Side panel size ...

  • GE Monogram ZIR36N LH - page 4

    4 For a complete food storage center , install a Monogram Freezer and Refrigerator side by side. Order ZUG75 Unified Grille Panel Kit for one continuous 3/4" panel. • Electrical and water locations must be located as shown for either type of installation. A separate 115V , 60Hz. 20 amp power supply is recommended for each product. NOTE: Addi ...

  • GE Monogram ZIR36N LH - page 5

    5 Installation At End-of-Run Frameless Cabinets NOTE: 1/2" thick side panels shown. Side panels can be any thickness. Add side panel thickness to outside trim width, (36 ” or 72" for two models) to calculate the rough-in dimension. The leading (front) edge must be finished to match surrounding cabinetry . Side panels, 1/2" minimum ...

  • GE Monogram ZIR36N LH - page 6

    6 T rim kit descriptions ZGC2 – Provides 1/4" grille panel frame side pieces for 83-1/2" and 84-1/2" installation heights. The supplied grille panel frame is factory set for 84". ZKHR1 – Provides the necessary framework to install a custom handle, of your choice , onto a 1/4" thick panel. (Handle not included.) ZKHRSSI ...

  • GE Monogram ZIR36N LH - page 7

    7 ZIR36N Refrigerator ZIF36N Freezer Design Information Designed to be installed flush or semi-flush with surrounding cabinetry . Cutout dimensions, clearances and side panel sizes are determined by the many installation options available. Side panels must be used whenever the sides of the refrigerator will be exposed. Side panels are not required ...

  • GE Monogram ZIR36N LH - page 8

    8 Custom Door Panel Dimensions Using Standard T rim 1/4" thick panels or Panels secured to 1/4" thick backing ZIR36N Refrigerator ZIF36N Freezer • 1/4" Panel: Cut panels to size. • Custom handle with 1/4" door panel requires T rim kits ZKHR1 or ZKHRSS1 for tubular stainless steel handles. Standard T rim with Panels secured t ...

  • GE Monogram ZIR36N LH - page 9

    9 ZIR36N Refrigerator ZIF36N Freezer • The ZKTR36LH (or ZKTR36RH) trim kit provides for the installation of 3/4" thick custom door and grille panels, using the supplied handle. Cut panel to size and install. Custom Door Panel Dimensions Using T rim Kits ZKTR36LH or ZKTR36RH 3/4" thick panel with kit supplied handle Installation Height D ...

  • GE Monogram ZIR36N LH - page 10

    10 ZIR36N Refrigerator ZIF36N Freezer • The ZKTR36LH (or ZKTR36RH) trim kit installed together with a ZKHTR1 custom handle kit provides for the installation of 3/4" thick custom door and grille panels with a custom handle of your choice. Order ZKHTRSS1 for a tubular stainless steel handle. Cut panels to size, rout the handle side of the pane ...

  • GE Monogram ZIR36N LH - page 11

    23 5/16" 84" 2 5/16" 24 3/4" 84" 3 3/4" 23 9/16" 84" 2 9/16" T rim 11 1/4" Side Panels Insert end of side panel into trim. Use stick-on hook and loop fastener strips to secure the panel to the refrigerator . Standard 4" high toekick or trim to fit. Height may vary depending on application. 1/2& ...

  • GE Monogram ZIR36N LH - page 12

    12 T ools Required • T insnips to cut banding • Stepladder • 1-1/4" open-end wrench • Bucket • Level • Appliance Hand T ruck • T ubing cutter • 7/16" open-end wrench • #2 Phillips screwdriver • Stubby Phillips screwdriver • Drill and appropriate bits • 7/16" socket with 3" extension for ratchet • Safety ...

  • GE Monogram ZIR36N LH - page 13

    13 • Remove outer carton. – Carefully cut banding at the top and bottom. • Slide out back corner posts (2). • Slide carton off top of cabinet. NOTE: IT IS NOT NECESSARY TO LA Y CABINET DOWN IN ORDER TO REMOVE SKID! • The unit is secured to the skid with 4 slotted tie-down straps. First remove the 5/16" bolts from the base channels in ...

  • GE Monogram ZIR36N LH - page 14

    14 Step 2 Install Water Line • Install optional water filter in the water line near the refrigerator . A water filter is recommended in areas where water supply contains sand or particles. Installation instructions are packed with the filter . • A cold water supply is required for automatic icemaker operation. The water pressure must be between ...

  • GE Monogram ZIR36N LH - page 15

    15 Step 3 Install Side Panels • Side panels are not required when the refrigerator or freezer is installed into an enclosure. Skip this step if you are installing into an enclosure. • Side panels are required whenever the sides of the ...

  • GE Monogram ZIR36N LH - page 16

    16 Step 5 Level Refrigerator or Freezer All models have 4-point leveling. The front is supported by leveling legs, the rear is supported by wheels. • Adjust rear wheels beneath the product to just barely touch the 2x4 block. • T urn the 7/16" hex nut located above the front wheels. T urn to raise or lower the refrigerator . • For front l ...

  • GE Monogram ZIR36N LH - page 17

    17 Step 9 Check Power • Check to make sure power is on by opening the door to see if interior lights are on. If you are using a 3/4" thick custom panel, SKIP THIS STEP . See Dimensions and Specifications for grille panel sizes. Order ZKTR36LH or ZKTR36RH and follow the installation instructions packed with the kit. The grille panel frame is ...

  • GE Monogram ZIR36N LH - page 18

    18 Step 13 Start Icemaker • A standard toekick is supplied. Install with 2 screws provided, adjust to desired height and tighten screws. IMPORT ANT : The vented toekick must remain unobstructed for proper air circulation and operation. Step 14 Install T oekick Step 12 Arrange Interior and Set T emperature Controls • Remove internal packing mate ...

  • GE Monogram ZIR36N LH - page 19

    19 This kit provides optional side trim pieces for the original grille panel frame to fit 83-1/2" and 84-1/2" installation heights. T o change grille panel size: • Determine the installation height by measuring the enclosure from the floor to the underside of soffit. When there is no soffit, measure to the top of the adjacent cabinets. ...

  • GE Monogram ZIR36N LH - page 20

    20 T ools and materials required: • #2 Phillips screwdriver • Drill and appropriate bits • Custom door panel • Custom Handle • Safety glasses Parts List: A. Handle side door extrusion (for left hand models) B. Handle side door extrusion (for right hand models) This kit provides the necessary framework to install a custom handle, of your c ...

  • GE Monogram ZIR36N LH - page 21

    21 Step 2 Locate handle position • Determine the desired location of the custom handle and mark centerlines of the screw holes. • Drill 1/16" pilot hole through the panel until it starts into the aluminum extrusion. This will mark the matching location for drilling the clearance hole when assembling the handle, panel and extrusion. • Sli ...

  • GE Monogram ZIR36N LH - page 22

    22 Right hand door swing models are illustrated in these instructions. Follow these instructions for left hand models. T ools and materials required: • #2 Phillips screwdriver • Drill and appropriate bits • Custom door panels • Putty knife • Safety glasses • 7/16" wrench Parts List A. T op trim B. Handle side trim C. Hinge side tri ...

  • GE Monogram ZIR36N LH - page 23

    23 Step 2 Install 3/4" trim Step 3 Apply panel support brackets • Attach the new 3/4" trim pieces on the top, hinge side and bottom using original screws. • Position support bracket on the back side of the custom panel, 14-5/16" from the hinge side. Secure support bracket to panel with screws provided. Step 4 Install panels • P ...

  • GE Monogram ZIR36N LH - page 24

    24 Step 5 Install handles Step 6 Adjust grille panel height • Install new door handle using original screws. • Secure the grille panel support to the back side of the 3/4" custom panel with #6 screws. • Be sure the lip of the support is over the top of the wood panel. Step 7 Secure 3/4" panel to grille panel support • For shipping ...

  • GE Monogram ZIR36N LH - page 25

    25 Step 8 Install grille panel • Install four of the six larger undercut screw so that the top of the screws are 1/16" from the surface of the support. • Attach the assembled panel to the grille opening by inserting the four protruding screws into the brackets on each side. Back View Grille Panel Support 1/16" ZKTR36LH/ZKTR36RH T rim ...

  • GE Monogram ZIR36N LH - page 26

    26 3/4" custom door panel must be routed to accommodate these door handle extrusions. Rout the panel as illustrated, 1/4" deep, and 1-13/16" wide on the handle side. Refer to installation instructions for ZKTR36LH or ZKTR36RH trim kit for 3/4" custom panels: • Follow Step 1 to remove the standard aluminum trim. • Follow Step ...

  • GE Monogram ZIR36N LH - page 27

    27 • Place the prepared 3/4" custom door panel on the bottom trim with support bracket tabs inserted into trim slots. • Push the panel back against the steel door , making sure the panel is flush with the hinge side trim. • Secure the panel to the trim temporarily by driving 2 screws through the backside of the trim at the top. • Slide ...

  • GE Monogram ZIR36N LH - page 28

    28 Step 4 Mount assembled panel • Place assembled panel onto the bottom trim with support bracket tabs inserted into slots. • Push the panel back against the steel door with handle extrusion flush to handle side of the door . • Open door fully to stop. • Install original screws at the top, hinge side and handle side. ZKHTR1 T rim Kit (For 3 ...

  • GE Monogram ZIR36N LH - page 29

    29 Step 1 Remove handle Right hand door swing models are illustrated in these instructions. Follow these instructions for left hand models. NOTE: It is best that 2 people install this kit. T ools and materials required: • #2 Phillips screwdriver • Drill and appropriate bits • Custom door panel • Safety glasses • Center punch • Masking t ...

  • GE Monogram ZIR36N LH - page 30

    30 Step 2 Match handle extrusions to handle FOR CUSTOM WOOD PA N E L S See Step 2A for Stainless Steel panels • Cut a piece of corrugated to use as a pad to protect the panel finish. Use 1/2" thick section of plywood to protect flooring when drilling. • Place custom panel on the pad, appearance side down. • On the back side of the panel ...

  • GE Monogram ZIR36N LH - page 31

    31 Step 3 Install standoffs onto handles • Place a handle standoff onto each attachment post along the handle. Position the set screw hole on the standoff to point to the floor . • Install set screws into the bottom of each standoff, using the Allen wrench provided. The standoff should be tight against the handle. Step 4 Install handles and pan ...

  • GE Monogram ZIR36N LH - page 32

    32 Raised Panel on 1/4" Thick Backing: A raised panel design secured to a 1/4" thick backing (screwed or glued) can be used with this handle kit. • Cut the 1/4" thick panels to size. • Fabricate the raised panel to allow 1-1/4" clearance from the hinge side of the panel to avoid striking adjacent cabinetry . • Allow 5/16&q ...

  • GE Monogram ZIR36N LH - page 33

    33 Before you begin: Right hand door swing models are illustrated in these instructions. Follow these instructions for left hand models. This kit provides for the installation of a T ubular Stainless Steel handle on a 3/4" thick decorator door panel. The door extrusions allows the custom handle to be secured to the door structure, rather than ...

  • GE Monogram ZIR36N LH - page 34

    34 Step 1 Match Handle Extrusion to Panel • Cut a piece of corrugated to use as a pad to protect the panel finish. Additional material may be required to protect flooring when drilling. • Place custom panel on the pad, appearance side down. • Select handle extrusion for your model, left or right side extrusion. • Place extrusion against the ...

  • GE Monogram ZIR36N LH - page 35

    35 This kit provides for the installation of a 3/4" thick custom grille panel to span the combined width of a side by side installation. Use this kit in combination with 3/4" custom panel kits, ZKTR36LH and ZKTR36RH. T ools and materials Required: • #1 and #2 Phillips screwdrivers or sockets • 1/4" angled wrench and 1/2" ope ...

  • GE Monogram ZIR36N LH - page 36

    36 • Cut a 2"x4" block, 71" long. Secure the 2"x4" to the 4 mounting brackets provided using #12 or #14 wood screws. • Secure the brackets with wood block to the back wall so that it is 84" (or your installation height) from the finished floor . Use #12 or #14 wood screws. See illustration. • Screws must penetrat ...

  • GE Monogram ZIR36N LH - page 37

    Stud Spacer Block Refrigerator Cabinet Door 37 Step 5 Install Center T rim Strip • Open doors fully . • Starting at the top, press trim strip over inside case trims of both products. • Continue pressing trim until you reach the bottom of the case trims. The trim will align with the top and bottom of the case trim. Case Trim U-Shape Trim Step ...

  • GE Monogram ZIR36N LH - page 38

    38 Step 7 Install Grille Base Cover • Open doors fully . • Install the double width grille base cover by slipping the notched ends over the hinges. • Place wire fence over the grill base cover (textured side out). Drive original wire fence screws through the fence, the grille base cover and into the frame. Step 8 Remove Grille Frame • Back ...

  • GE Monogram ZIR36N LH - page 39

    39 Step 9 Install Soffit Ve n t T o p • Separate the top and hinge side trim pieces by removing side screws. Discard top piece, retain screws. • Install one end piece to unified top piece with 2 original screws. • Slip end of rubber dust gasket into end of top unified piece and slide trim towards the center . Engage the second piece of gasket ...

  • GE Monogram ZIR36N LH - page 40

    Pub. No. 49-60055-3 Dwg. No. 197D2785P001 12-03 JR 65160-01 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local ser vice in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specificatio ...

Manufacturer GE Monogram Category Refrigerator

Documents that we receive from a manufacturer of a GE Monogram ZIR36N LH can be divided into several groups. They are, among others:
- GE Monogram technical drawings
- ZIR36N LH manuals
- GE Monogram product data sheets
- information booklets
- or energy labels GE Monogram ZIR36N LH
All of them are important, but the most important information from the point of view of use of the device are in the user manual GE Monogram ZIR36N LH.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals GE Monogram ZIR36N LH, service manual, brief instructions and user manuals GE Monogram ZIR36N LH. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product GE Monogram ZIR36N LH.

Similar manuals

A complete manual for the device GE Monogram ZIR36N LH, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use GE Monogram ZIR36N LH by users. Manuals are usually written by a technical writer, but in a language understandable to all users of GE Monogram ZIR36N LH.

A complete GE Monogram manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual GE Monogram ZIR36N LH - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the GE Monogram ZIR36N LH, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the GE Monogram ZIR36N LH, that we can find in the current document
3. Tips how to use the basic functions of the device GE Monogram ZIR36N LH - which should help us in our first steps of using GE Monogram ZIR36N LH
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with GE Monogram ZIR36N LH
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of GE Monogram ZIR36N LH in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning GE Monogram ZIR36N LH?

Use the form below

If you did not solve your problem by using a manual GE Monogram ZIR36N LH, ask a question using the form below. If a user had a similar problem with GE Monogram ZIR36N LH it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)