English dropdown-ico

Manual GE ZBD5700

24 pages 0.78 mb
Download

Go to site of 24

Summary
  • GE ZBD5700 - page 1

    GE Monogram ® Installation Instr uctions with Optional T rim Kit Installation Instr uctions Built-In Dishwashers Models ZBD5600 ZBD5700 ZBD5900 ...

  • GE ZBD5700 - page 2

    2 Before you begin - Read these instructions completely and carefully. IMPORTANT - Save these instructions for local inspector’s use. IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer - Be sure to leave these instructions with the Consumer. Note to Consumer - Keep these instructions with your Use and Care Book for future r ...

  • GE ZBD5700 - page 3

    3 Design Information Stainless Steel Interior Dishwashers Models Available ZBD5600 WW , ZBD5700 WW White Dishwashers ZBD5600 BB, ZBD5700 BB Black Dishwashers ZBD5900 SS Stainless Steel Dishwasher These dishwashers ar e designed for versatility , adaptable to virtually any installation. These models have a full length trimless door without the tradi ...

  • GE ZBD5700 - page 4

    4 Design Information Stainless Steel Interior Dishwashers Standard installation in 24” deep cabinets • Install in standard 24” deep cabinets: – The dishwasher door will be flush with the fr ont face of adjacent cabinetr y . • With a 3/4” thick custom door panel in place, the exterior is trimless and fits flush to adjacent cabinetr y . ? ...

  • GE ZBD5700 - page 5

    5 Installation Infor mation Stainless Steel Interior Dishwashers Par ts Supplied Remove the hardware accessor y bag and other parts from inside or taped to the outside of the dishwasher . Check contents against drawings to insure that all par ts ar e included. ■ ■ 2 toekick slides ■ ■ 2 toekick support brackets ■ ■ 2 side trim pieces ? ...

  • GE ZBD5700 - page 6

    6 Installation Preparation Stainless Steel Interior Dishwasher Materials Y ou W ill Need: (not supplied) ■ ■ 90 ° elbow (3/8" NPT external thread on one end and opposite end to fit hot water supply line) ■ ■ Thread seal tape ■ ■ UL listed wire nuts (3) For new installations only: ■ ■ Air gap for drain hose, if required ■ ■ ...

  • GE ZBD5700 - page 7

    7 Installation Preparation Stainless Steel Interior Dishwasher • The rough cabinet opening must be 24” min. deep, 23-5/8” min. to 24” max. wide. The opening height should be 34” min. and 35” max. • The opening should be fr ee of extraneous pipes and wires. Pr epare the Opening W ater Supply • Hot water line may enter from either sid ...

  • GE ZBD5700 - page 8

    8 Installation Preparation Stainless Steel Interior Dishwashers Electrical Requir ements: These dishwashers must be supplied with a 120 volt, 60 Hz power supply with an indi- vidual, properly gr ounded branch circuit, protected by a 15 or 20 amp fuse or cir cuit breaker or time delay fuse. • Wiring must be 2 wire with ground. • If electrical su ...

  • GE ZBD5700 - page 9

    9 Installation Preparation Stainless Steel Interior Dishwasher Prepare drain plumbing • Follow local codes and ordinances. • Dishwasher drain hose must not exceed 10 feet in length for proper drainage. – The dishwasher is supplied with a 3/4” I.D. drain hose, 78” long. Add up to 42” length to the factor y supplied hose if necessar y . ? ...

  • GE ZBD5700 - page 10

    10 Installation Stainless Steel Interior Dishwasher Install Custom Door Panel • If you intend to install custom door panels, refer to installation instr uctions provided in this booklet. The panels should be in place before installing the dishwasher . Step 1 Remove wood base Step 2 Install leveling legs & toekick brackets • Un-wrap the drai ...

  • GE ZBD5700 - page 11

    11 Installation Stainless Steel Interior Dishwasher Step 3 Install W ater Inlet Fittings Step 4 Install power cord (If used) Skip this step If dishwasher will be wired direct. • Install the 90 ° elbow onto the water inlet. Use thread sealing tape or pipe thread compound. • The 90 ° elbow should face the left or right side, depending on water ...

  • GE ZBD5700 - page 12

    12 Installation Stainless Steel Interior Dishwasher Step 5 Level the Dishwasher Step 6 Slide Dishwasher Into Opening • Carefully upright the dishwasher , taking care not to bend the leveling legs. Make sure the leveling leg locking nuts are secure. • Check to be sure the dishwasher is level and at the cutout height. • Inser t drain hose into ...

  • GE ZBD5700 - page 13

    13 Installation Stainless Steel Interior Dishwasher • Follow all local codes and ordinances. Drain Line Pr eparation • The dishwasher is supplied with a 78” long corr ugated drain hose. • If the location requir es a longer drain hose, add up to 42” length to the supplied hose. Use 3/4” inside diameter hose and thin wall copper coupler t ...

  • GE ZBD5700 - page 14

    14 Installation Stainless Steel Interior Dishwasher Step 10 Secure Dishwasher to Counter top or Cabinetr y T o maintain position and alignment the dishwasher must be secur ed to the counter top or to adjacent cabinetr y . If countertop is of stone or other hard material, secure the dishwasher to adjacent cabinets. • Check to be sure that dishwash ...

  • GE ZBD5700 - page 15

    15 Installation Stainless Steel Interior Dishwasher • Install toekick slides to toekick support brackets. Use slide stamped “L” on left and “R” on right side. • Align front and inner toekicks, matching screw holes. • Align toekick to second screw hole in toekick slide as illustrated. • Install color matched screws “E” through th ...

  • GE ZBD5700 - page 16

    16 ZPF25 Custom Door Panel Kit 1/4" Thick Custom Door Panel • Cut door panel to the dimensions shown. • The bottom left and right corners should be cut at 1/4” radius. See illustration. Note: The trim will conceal the cut edges of the panels. T o prevent electrical shock, disconnect electrical power supply to dishwasher before changing p ...

  • GE ZBD5700 - page 17

    17 ZPF25 Custom Door Panel Kit 1/4" Thick Custom Door Panel • Place the supplied metal door on a flat sur face. • Place the custom panel on top of the metal door . • Place supplied trim over the custom panel. • Press trim to panel and install the color matched screws provided. Install 3 screws on each side and 2 scr ews on the bottom. ...

  • GE ZBD5700 - page 18

    18 ZPF25 Custom Door Panel Kit 1/4" Thick Custom Door Panel The additional weight of the custom panel may require that the heavy door springs be installed. T est Door Balance • With one hand under the door , slowly open the door fully . • Open and close the door to check for proper balance. Correct door balance should prevent the door from ...

  • GE ZBD5700 - page 19

    19 ZPF75 Custom Panel Kit 3/4" Thick Custom Door Panel ZPF75B, Black ZPF75W , White Tools and Materials required • Phillips screwdriver • Gloves to protect against sharp edges • Nut driver Step 1: Deter mine Custom Panel Sizes The custom panel should be constr ucted in the same manner as cabinet doors. All edges can be seen and must be f ...

  • GE ZBD5700 - page 20

    20 ZPF75 Custom Panel Kit 3/4" Thick Custom Door Panel Step 2 Remove Existing Metal Door • Open the door fully . Caution: One person should hold the door while the other backs out screws to prevent the metal door from falling. • Remove 6 screws on the inside of the frame. Retain screws. • Remove the 2 screws with o-rings located in the b ...

  • GE ZBD5700 - page 21

    21 ZPF75 Custom Panel Kit 3/4" Thick Custom Door Panel Step 5 Install Assembled Door onto Dishwasher Note: One person should hold the door while the other installs screws to prevent the door assembly from falling. • Check to be sure that foam inserts are in place. • Hold the assembled door to dishwasher inner door and slide up against cont ...

  • GE ZBD5700 - page 22

    22 ZPF75 Custom Panel Kit 3/4" Thick Custom Door Panel Step 7 Install Custom T oekick • Slip toekick slides into guides by pulling out the metal tabs. • Hold custom panel against toekick slides and mark screw hole locations. • Remove toekick and drill 1/8" pilot holes. • Remove toekick slides and secure panel to slides with 2 scre ...

  • GE ZBD5700 - page 23

    23 Notes Stainless Steel Interior Dishwasher ...

  • GE ZBD5700 - page 24

    Pub. No. 49-5860-1 Printed in USA  1999 GE Appliances (N.D. 458) 9/99 Part Number: C82 0017x Issue A NOTE: While performing installations described in this book, safety glasses or goggles should be worn. T o obtain specific information concer ning any Monogram pr oduct or ser vice, call GE Answer Center ® consumer information ser vice at 800.62 ...

Manufacturer GE Category Dishwasher

Documents that we receive from a manufacturer of a GE ZBD5700 can be divided into several groups. They are, among others:
- GE technical drawings
- ZBD5700 manuals
- GE product data sheets
- information booklets
- or energy labels GE ZBD5700
All of them are important, but the most important information from the point of view of use of the device are in the user manual GE ZBD5700.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals GE ZBD5700, service manual, brief instructions and user manuals GE ZBD5700. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product GE ZBD5700.

Similar manuals

A complete manual for the device GE ZBD5700, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use GE ZBD5700 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of GE ZBD5700.

A complete GE manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual GE ZBD5700 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the GE ZBD5700, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the GE ZBD5700, that we can find in the current document
3. Tips how to use the basic functions of the device GE ZBD5700 - which should help us in our first steps of using GE ZBD5700
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with GE ZBD5700
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of GE ZBD5700 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning GE ZBD5700?

Use the form below

If you did not solve your problem by using a manual GE ZBD5700, ask a question using the form below. If a user had a similar problem with GE ZBD5700 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)