English dropdown-ico

Manual Roland RD-700NX

106 pages 21.98 mb
Download

Go to site of 106

Summary
  • Roland RD-700NX - page 1

    * 5 1 0 0 0 1 6 9 8 3 - 0 2 * ...

  • Roland RD-700NX - page 2

    202 + 3a Copyright © 2010 ROLAND C ORPORA TION All rights reserved. No part of this publication may be reproduced in an y form without the written permission of ROLAND CORPORA TION. Roland, GS, and SuperNA TURAL are either reg istered trademarks or trademarks of Roland Corporation in the Unit ed States and/or other countries. 201b Before using thi ...

  • Roland RD-700NX - page 3

    4 USING THE UNIT SAFEL Y Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly . * Material damage refers t o damage or other adverse eects caused with respect to the home and all its furnishings, as well to domestic animals or pets. Used for instructions intended to alert th ...

  • Roland RD-700NX - page 4

    5 USING THE UNIT SAFEL Y 012a Immediately turn the power o , remove the power cor d from the outlet, and request servicing by your retailer , the nearest Roland Service Center , or an authorized Roland distributor , as listed on the “Information ” page when: • The power-supply cord or the plug has been damaged; or • I f smoke or unusual ...

  • Roland RD-700NX - page 5

    6 IMPORT ANT NO TES P ow er Supply 301 • Do not connect this unit to same electrical outlet that is being used by an electrical appliance that is controlled by an in verter (such as a refrigerator , washing machine, micro wave ov en, or air conditioner), or that contains a motor . Depending on the way in which the electrical appliance is used, po ...

  • Roland RD-700NX - page 6

    7 IMPORT ANT NOTES Using USB Memories 704 • Carefully insert the USB memories all the way in; until it is rmly in place. 705 • Never touch the terminals of the USB memories . Also, av oid getting the terminals dirty. 708 • USB memories are constructed using precision componen ts; handle the USB memories carefully , paying par ticular note ...

  • Roland RD-700NX - page 7

    8 U S I N G T H E U N I T S A F E L Y ............................. 4 I M P O R T A N T N O T E S ................................. 6 P a n e l D e s c r i p t i o n s ................................. 10 F r o n t P a n e l ...................................................... 10 R e a r P a n e l ................................................. ...

  • Roland RD-700NX - page 8

    9 Cont ents M a k i n g S y s t e m S e t t i n g s ......................................... 66 T uning to O ther Instruments’ Pitches (Master Tune) . . . . . . . . . 67 Adjusting the Volume (Master Volume) . . . . . . . . . . . . . . . . . . . . . 67 Prev enting Equalizer Settings from Being Switched (EQ M o d e ) .............................. ...

  • Roland RD-700NX - page 9

    10 P anel Descriptions 1. [ VOLUME] slider Adjusts the over all volume that is output from the r ear panel OUTPUT jacks, PHONES jack, and BALANCED OUT jacks (p. 18). 2. [ V-LINK] Button Switching this on lets you con trol external V-LINK compatible video equipment connected to the RD-700NX (p. 83). 3. EQU ALIZER [L OW ] Knob Adjusts the sound’ s ...

  • Roland RD-700NX - page 10

    11 Panel Descriptions 6. DISPLA Y This shows the Live Set names and the values of v arious settings, etc. [LA YER EDIT ] Button This allows you t o change the Layer settings (p . 56). Y ou can also use this to assign functions in some screens. [TONE EDIT ] Button This allows you t o change the tone settings (p. 54). Y ou can also use this to assign ...

  • Roland RD-700NX - page 11

    12 Panel Descriptions Rear P anel 12 13 14 15 16 17 18 19 20 21 12. [POWER ON] Swit ch This switch turns the power on/o (p. 17). 13. A C IN Connector Connect the included power cord t o this connector (p. 14). 14. USB MEMORY C onnec tor Connect separately sold USB memory or a CD-ROM dr ive here (p . 18). Use USB memory or a CD -ROM drive made by ...

  • Roland RD-700NX - page 12

    13 Getting Ready Placing the RD -700NX on a Stand If you place the RD-700NX on a stand, you must use the KS-G8 (sold separately). When placing the RD -700NX on the KS-G8, place it in the position shown below . NO TE Using the RD-700NX with any other stand may produce an unstable situa tion, possibly causing the instrument to fall or overturn, and r ...

  • Roland RD-700NX - page 13

    14 Getting Ready Connecting the P ow er Cor d Rear Panel 1. Before y ou begin making connections, con rm the following. Is the volume level of the RD-700NX or connected amp turned all the way down? Is the power to the RD-700NX or connected amp turned o ? 2. Connect supplied power c ord to the A C IN connector of the RD-700NX, and plug the oth ...

  • Roland RD-700NX - page 14

    15 Getting Ready Connecting the Ex ternal E quipment to RD-700NX The RD-700NX is not equipped with an ampli er or speakers. In order to pr oduce sound, you need to hook up audio equipmen t such as a monitor speaker or a stereo set, or use headphones. * Audio cables, USB cables, MIDI cables, headphones , expression pedals, and USB memory are not ...

  • Roland RD-700NX - page 15

    16 Getting Ready 1. Before y ou begin making connections, con rm the following. Is the volume level of the RD-700NX or connected amp turned all the way down? Is the power to the RD-700NX or connected amp turned o ? 2. Connect supplied power c ord to the A C IN connector of the RD-700NX, and plug the other end into an AC outlet . 3. Connect th ...

  • Roland RD-700NX - page 16

    17 Getting Ready T urning the Po wer On and O  NO TE Once the connections have been completed (p . 15), turn on power to your various devices in the order speci ed. By turning on devices in the wrong order , you risk causing malfunction and/or damage to speakers and other devices. T urning On the Po wer 1. Before y ou turn on the power , use ...

  • Roland RD-700NX - page 17

    18 Getting Ready Adjusting the V olume 1. Adjust the volume using the [VOLUME] slider . Move the slider up to increase the v olume, or down to lo wer it. Also adjust the volume of the connected device to an appr opriate level. Adjusting the Display C ontrast The characters in the display may be di cult to view immediately after turning on the po ...

  • Roland RD-700NX - page 18

    19 Getting Ready Connecting the CD D riv e If you’ re using a stand (KS-G8), you can use the screw holes on the bottom of the RD-700NX to attach a CD drive (sold separa tely). MEMO For inf or mation on turning on/o your CD drive and how to insert or remove a CD , refer to the owner’ s manual that came with your CD drive. 1. Connect the USB c ...

  • Roland RD-700NX - page 19

    20 RD-700NX Rewritable memory USB memory SONG Live Set Non-rewritable memory Preset memory Live Set 300 sets Rewritable memory User memory Live Set 100 sets Syst em memory T emporary memor y (T emporar y area) Live Set T emporar y memor y T emporar y area Data for the patch y ou select via the front panel buttons is called up to this area. When you ...

  • Roland RD-700NX - page 20

    21 Overview of the RD -700NX About Liv e Sets The RD-700NX lets you store the sounds that y ou create. A sound you create is called a “Live Set”; you can use the buttons to recall a Live Set and then play it. Live Sets are organized in to a “ preset bank” and a “ user bank. ” Live Set Contr oller Sec tion Sound Generator Section Layer ( ...

  • Roland RD-700NX - page 21

    22 Overview of the RD -700NX Main Screens The explanations in this manual include illustrations that depict what should typically be shown by the display . Note, however , that your unit may incorporate a new er , enhanced version of the system (e.g ., includes newer sounds), so what you actually see in the display may not always match wha t appear ...

  • Roland RD-700NX - page 22

    23 Overview of the RD -700NX Special Indications Indication Explanation When in the Live Set screen, this symbol will be shown in the upper-right part of the screen whenever you select a Live Set that has “ TW-Organ 1–10” assigned to any of its layers. Pressing the C ursor [ ] button while this mark is displayed brings up the T one Wheel scre ...

  • Roland RD-700NX - page 23

    24 Overview of the RD -700NX E diting a V alue When changing settings values, y ou can use the [DEC] and [INC ] buttons, V ALUE dial, or the LIVE SET buttons (numeric keys). [DEC ] Button, [INC] Button Pressing the [INC] button increases the value , and the [DEC ] button decreases it. Purpose Panel opera tion T o continuously change the value Hold ...

  • Roland RD-700NX - page 24

    25 Here ’ s how to listen to these demo songs . The RD-700NX features the internal demo songs that e xhibit the special capabilities of the instrument. Demo song “ T one Preview ” makes e ective use of the internal tones. There are sevent een demo songs, and each of the One T ouch buttons and LIVE SET buttons corresponds to one of the song ...

  • Roland RD-700NX - page 25

    26 P er f ormance Piano P er formanc es Now , tr y per forming with the piano . The RD-700NX lets you call up the ideal settings for piano performance at any time simply by pr essing a button. Y ou can also select your preferred tones and settings and store them to the RD-700NX’ s buttons. 1 2 1. Press the ONE TOUCH PIANO butt on or the ONE TOUCH ...

  • Roland RD-700NX - page 26

    27 P er formance P er forming with a V ariety of Live Sets The RD-700NX comes with a many built-in Sounds. Each one of these individual sounds is called a “Live Set. ” Live Sets are assigned to the LIVE SET buttons accor ding to the tone category selected. Each category has several variations. T r y selecting and per forming with a number of di ...

  • Roland RD-700NX - page 27

    28 P er formance Playing Multiple T ones with the Keyboar d The RD-700NX features f our Internal layers (UPPER 1, UPPER 2, L OWER 1, and L OWER 2), and one tone can be assigned to each of these lay ers. Y ou can perform using combinations of tones by turning each layer on or o . Y ou can have multiple tones la yered together at the same time , a ...

  • Roland RD-700NX - page 28

    29 P er formance Playing Di eren t T ones in T wo Di erent Sec tions of the K eyboard Such a division of the keyboard into right- and left-hand sections is called a “ Split, ” and the key where the division takes place is called the “Split P oint. ” While in Split mode, a sound play ed in the right side is called an “UPPER part, ” ...

  • Roland RD-700NX - page 29

    30 P er formance Changing the T one for a Lay er 1 2 3 3 1. Press the [La yer EDIT ] button to acc ess the layer edit scr een. 2. Use the Cursor [ ] [ ] buttons to select the layer whose tone you wan t to change. Layers that hav e their Layer switch turned o are dimmed in the screen. 3. Use the LIVE SET buttons to select the tone category , and ...

  • Roland RD-700NX - page 30

    31 P er formance Adjusting the V olume Lev el for Individual Lay ers With the RD-700NX, each of the parts that is per formed using the internal sound generator is r eferred to as a Lay er. For each la yer (UPPER 1, UPPER 2, L OWER 1, LOWER 2), you can use the La yer switch and Lay er LEVEL slider to turn the sound on/o and adjust its volume. Lay ...

  • Roland RD-700NX - page 31

    32 P er formance T ransposing the Key of the Ke yboard (TRANSPOSE) Y ou can transpose performances without changing the keys you are pla ying, as well as change the pitch b y an octave. This feature is called “ T ranspose. ” This is a conv enient feature t o use when you want to mat ch the pitch of the keyboard performance to a vocalist’ s pi ...

  • Roland RD-700NX - page 32

    33 P er formance Adding Rev erberation t o the Sound (RE VERB) The RD-700NX can apply a reverb e ect to the notes you play on the keyboard. Applying reverb adds pleasing rev erberation to what you pla y , so it sounds almost as if you wer e playing in a concert hall. 1 2 1. Press the [REVERB] button. The reverb type switches each time you pr ess ...

  • Roland RD-700NX - page 33

    34 P er formance Changing the Sound ’ s Pitch in Real Time While playing the keyboard , move the lever to the left to lo wer the pitch, or to the right to raise the pit ch. This is known as P itch Bend. Y ou can also apply vibrato by manipulating the lev er away fr om you. This is known as Modulation. If you move the lever a way from you and a t ...

  • Roland RD-700NX - page 34

    35 P er formance Adjusting the L ev els of Each Frequency R ange (EQUALIZER) The RD-700NX is equipped with a four-band equalizer. Y ou can use the EQU ALIZER [L OW ] knob, [L OW MID] k nob, [HIGH MID ] knob, and [HIGH] knob to adjust the level of each frequency range. By holding down the [EXIT/SHIFT ] button and turning the corresponding knob, you ...

  • Roland RD-700NX - page 35

    36 P er formance Disabling the Button By engaging the P anel Lock function, you can disable panel func tions. This prevents settings from being changed inadv er tently on stage or in other such situations. However , you ’ll still be able to operate the f ollowing buttons and knobs even while P anel Lock is in for ce. • [ VOL UME] slider • [DI ...

  • Roland RD-700NX - page 36

    37 Using the C onv enient F unc tions in P er formances Playing Rh ythm The RD-700NX features internal drum patt erns complementing Jazz, Rock, and other various musical genres. These drum patterns are referred t o as “ Rhythms. ” 1 3 2 1. Press the [SELECT ] button to make the button indicat or light. The SONG/RHYTHM screen will appear . 2. Pr ...

  • Roland RD-700NX - page 37

    38 Using the C onv enient Functions in P er formances Playing the Songs Here ’ s how to play back SMF music  les, audio data, or songs from a CD . MEMO Y ou can play songs that are sa ved on USB memory (sold separately). For details , refer t o “C onnecting the USB Memor y ” (p. 18). If you want to connect a separately sold CD drive and pl ...

  • Roland RD-700NX - page 38

    39 Using the C onv enient Functions in P er formances Changing Song T empos 1. In the SONG screen, press the C ursor [ ] button or [ ] button to mov e the cursor to the tempo indication in the top line of the screen. If an audio  le is selected, the value will be indicated as a percentage . 2. Use the [DEC] [INC] buttons or the V AL UE dial to c ...

  • Roland RD-700NX - page 39

    40 Using the C onv enient Functions in P er formances Recording Audio The RD-700NX lets you easily record y our performance as an audio  le. Y ou can then play back the recor ding to evaluate y our per formance . 3 7 8 6 4 5 9 10 Getting ready t o recor d NO TE Y ou must not disconnect the USB memory. 1. Connect your USB memory to the external m ...

  • Roland RD-700NX - page 40

    41 Using the C onv enient Functions in P er formances Applying E ects to the Sound (MFX) In addition to chorus (p. 33) and rev erb (p. 33), the RD-700NX also allows y ou to apply “ multi-e ects” to sounds. Multi-e ects provides a collection of 84 di erent e ec ts, such as distortion and rotary, fr om which you can choose. Y ou ca ...

  • Roland RD-700NX - page 41

    42 Using the C onv enient Functions in P er formances Simulating the Crea tion of O rgan T ones When any of the “ T W-Organ 1–10” T ones is selec ted for an y of the layer , you can perform in “ T one Wheel mode, ” in which the creation of organ sounds is simulated. An organ featur es nine “harmonic bars” that can be drawn in and out, ...

  • Roland RD-700NX - page 42

    43 Using the C onv enient Functions in P er formances Changing the Undulation of the Or gan T one (Rotar y Eect) While the T one Wheel screen is displa yed, you can change the undulation r ate of the Rotary eect with the Pitch Bend lever . The Rotary eect is an eect that recreates the sound of the rotating speakers used t o augment the ...

  • Roland RD-700NX - page 43

    44 Using the C onv enient Functions in P er formances S elec ting Stor ed Settings (Live Set ) The RD-700NX’ s Layer (p . 56) and EXTERNAL Layer (p . 59) tone settings, e ect settings, and other such settings are collectively referr ed to as a “ Live Set. ” Once you ’ve stor ed your pref erred settings, and settings for the songs t o be ...

  • Roland RD-700NX - page 44

    45 Using the C onv enient Functions in P er formances Storing Settings to Liv e S ets If you want to use the changed conten t as a new Live Set, use the following pr ocedure to sav e the settings to user bank. Y ou can store 100 Live Sets on the RD-700NX. Y ou can also change the name of a Live Set. 1. Press the [ WRITE] button, getting the indicat ...

  • Roland RD-700NX - page 45

    46 Making Detailed Settings for the Piano T ones Y ou can make detailed settings to adjust the piano sound that’ s used when you press the ONE TOUCH PIANO button (p . 26). These detailed settings can be saved f or each variation. NO TE When you press one of the ONE TOUCH PIANO buttons , all settings other than the tone settings will be set to the ...

  • Roland RD-700NX - page 46

    47 Making Detailed Settings for the ONE T OUCH T ones Piano P arameters Paramet er Value Description (T one Name) – Selects the tone. Stereo Width CENTER, L01-01R–L63-63R The higher the value set, the wider the sound is spread out. Nuance TYPE1, 2, 3 This changes the T one’ s subtle nuances by altering the phase of the left and right sounds. ...

  • Roland RD-700NX - page 47

    48 Making Detailed Settings for the ONE T OUCH T ones Changing the Key T ouch Y ou can make advanced settings for the t ouch used for the keys. Changing this setting also changes the Key T ouch setting in Edit Mode (p. 71). Paramet er Value Description Key T ouch SPR LIGHT An even lighter setting than LIGHT . LIGHT This sets the keyboard to a light ...

  • Roland RD-700NX - page 48

    49 Making Detailed Settings for the ONE T OUCH T ones Paramet er Value Description Peaking Gain -15–+15 dB Amount of boost/cut produced by the lter at the specied frequency region of the input sound Peaking Q 0.5, 1.0, 2.0, 4.0, 8.0 Width of the frequency region boosted/cut by the P eaking Gain parameter (larger values make the region narro ...

  • Roland RD-700NX - page 49

    50 Making Detailed Settings for the ONE T OUCH T ones Making Detailed Settings for the E. Piano T ones The RD-700NX contains a SuperNA TURAL E. Piano sound genera tor . The SuperNA TURAL E. Piano sound gener ator is Roland’ s completely new sound generator , which faithfully models the varieties and characteristics of the vintage electric pianos ...

  • Roland RD-700NX - page 50

    51 Making Detailed Settings for the ONE T OUCH T ones E. Piano P arameters Paramet er Value Description T one TINE EP This is an E. Piano that widely used in the ‘70s. It is a standard sound that was loved by jazz and fusion players, and con tinues to have numerous fans t o this day . This sound is characterized by a bell-like attack and a mild t ...

  • Roland RD-700NX - page 51

    52 Making Detailed Settings for the ONE T OUCH T ones Selec ting an Eect Y ou can apply a multi-eect you’v e selected from 84 dierent e ec t types. F or details on the available eect types, ref er to the Eect List (p. 96). Selec ting the T ype of Amp This switches the amp of the E. P iano. By changing the combina tion of E. pian ...

  • Roland RD-700NX - page 52

    53 Making Detailed Settings for the ONE T OUCH T ones WURL Y This combines REED EP with a variation of it, repr oducing a typical E. piano sound of the ‘60s. Paramet er Value Description T reble -50–+50 Amount of boost/cut for the high-frequency range Bass -50–+50 Amount of boost/cut for the low-frequency range Vibra to Sw OFF , ON T urns tre ...

  • Roland RD-700NX - page 53

    54 Mak ing D etailed Settings for T ones Y ou can make more detailed settings to the tones assig ned to each of the layer . In certain selec ted T ones, there may be parameters that cannot be changed. 1. In the Live Set screen, press the [TONE EDIT ] button. The [ TONE EDIT ] button lit, and the TONE EDIT screen appears . 2. Press the C ursor [ ] [ ...

  • Roland RD-700NX - page 54

    55 Making Detailed Settings for T ones Paramet er Value Description Mono/Poly Species whether the tone will play polyphonically (POL Y ) or monophonically (MONO). The MONO setting is eective when playing a solo instrument tone such as sax or ut e. Additionally , when this is set to “MONO LEGA TO, ” you can have monophonic performances ...

  • Roland RD-700NX - page 55

    56 Making Detailed Settings for T ones Making La y er Settings The RD-700NX features f our Parts (UPPER 1, UPPER 2, L OWER 1, and L OWER 2) that you can use for freely controlling the int ernal parts with the RD-700NX’ s buttons and keyboard. These four parts that are used for con trolling the internal parts are collectively known as the “Layer ...

  • Roland RD-700NX - page 56

    57 Making Detailed Settings for T ones Paramet er Value Description VRL ( V elocit y Range Lower) 1–127 This species the lower limit (VRL) and upper limit ( VRU) of the range in which the tone is played according to the v elocity. Make this setting when you want the tone to change depending on the key velocity . This setting is disregarded wit ...

  • Roland RD-700NX - page 57

    58 U sing the RD -700NX As a Master Keyboar d By connecting an external MIDI device to the MIDI OUT connectors on the RD-700NX’ s rear panel, you can then control the external MIDI device fr om the RD-700NX. Normally , the RD-700NX will transmit note messages from the MIDI OUT connector , but if you press the [MIDI] button so the “MIDI” indic ...

  • Roland RD-700NX - page 58

    59 Using the RD-700NX As a Master Keyboard Adjusting the V olume of Each Lay er Layer Switch Layer LEVEL Slider Layer Layer Layer Layer [MIDI] Button When the [MIDI] button is lit, you can use the La yer switch and Layer LEVEL sliders to c ontrol the EXTERNAL Layer in the same wa y as with the Layer (p . 21). Lay er Switch This speci es whether ...

  • Roland RD-700NX - page 59

    60 Using the RD-700NX As a Master Keyboard Setting the MIDI T ransmit Channel When you hav e  nished connecting the external MIDI device, match the keyboar d’ s T ransmit channel and the Receive channel for each of the external MIDI sound generator’ s Parts. Sounds is produced when the MIDI channels for the sending device (the RD-700NX) and ...

  • Roland RD-700NX - page 60

    61 Using the RD-700NX As a Master Keyboard S elec ting Sounds on an Ex ternal MIDI Device T o switch the tones of an external MIDI device, the prog ram number and the MSB/LSB of the Bank Select message are entered as numerical values on the RD-700NX. 1 2 1. Press the [MIDI] button so the “MIDI” indicat or is lit. The MIDI screen appears. If “ ...

  • Roland RD-700NX - page 61

    62 Using the RD-700NX As a Master Keyboard Adjusting the V olume and P an ( V olume/Pan) Sets the volume and the panning (localizes sound image) for each of the T ones. The Volume setting is mainly used when multiple tones are playing t o obtain the desired balance in volume between each la yer . The P an setting positions the sound image of each l ...

  • Roland RD-700NX - page 62

    63 Using the RD-700NX As a Master Keyboard Changing the Range Tha t Plays in Response to the V elocit y ( V elocity Range) This species the lower limit (L WR) and upper limit (UPR) of the range in which the tone is played acc ording to how str ongly the keys are played (velocity). Make this setting when you want the t one to change depending on ...

  • Roland RD-700NX - page 63

    64 Using the RD-700NX As a Master Keyboard Setting the R ange for the Change in P itch with the Pit ch Bend Lev er (B end Range) This sets the amount of pitch change that will occur when y ou move the Pitch Bend lever (4 octav es). Paramet er RPN V alue B.R (Bend Range) 00H/00H - - - (OFF), 0–48 (semitone) Setting the Amount of Modulation A pplie ...

  • Roland RD-700NX - page 64

    65 Detailed Settings for Each F unc tion The MENU button can be used to make a variety of settings. Setting Par ameters T o setting screen Leaving setting screen Change the value Y ou can input the value using the LIVE SET buttons, and press the [ENTER] button to set the value. (The number of Edit screen pages may vary according to the menu selecte ...

  • Roland RD-700NX - page 65

    66 Detailed Settings for Each Function Menu Parameter Page 4. Compressor T ype p. 76 Split Fr equency L p . 76 Split Fr equency H p. 76 Depth p. 76 Level p. 76 Attack Time p. 76 Release Time p . 76 Threshold p. 76 Ratio p. 76 5. File Live Set Save p . 77 Live Set Load p. 78 Live Set Delete p. 78 Live Set Copy p. 79 SONG Delete p. 80 SONG Copy p. 80 ...

  • Roland RD-700NX - page 66

    67 Detailed Settings for Each Function T uning to Other Instruments ’ Pit ches (Master T une) For a cleaner ensemble sound while performing with one or more other instruments, ensure that each instrumen t’ s basic pitch is in tune with that of the other instruments. In general, the tuning of an instrument is indicated by the pitch in Hertz (Hz) ...

  • Roland RD-700NX - page 67

    68 Detailed Settings for Each Function Paramet er Value F unction/Parameter Setting Changed FC1 FC2 145: Live Set UP Switches the Live Sets in ascending order . 146: Live Set DOWN Switches the Live Sets in descending order . Retaining the C urr ent T one Ev en When T ones ar e Swit ched (T one Remain) This setting species whether the currently h ...

  • Roland RD-700NX - page 68

    69 Detailed Settings for Each Function Using P rogr am Change Messages to Swit ch Live Sets (Liv e S et C ontr ol Channel) Y ou can switch the RD-700NX’ s Live Sets with MIDI messages from an external MIDI device. Paramet er Value Description Live Set Ctrl Ch (Live Set Contr ol Channel) 1–16 Set the MIDI Receive channel for receiving the MIDI m ...

  • Roland RD-700NX - page 69

    70 Detailed Settings for Each Function Setting the T uning Method (T emperament/K ey) This sets the tuning and keynote (tonic). Most modern songs are composed and played with the assumption that equal temperament will be used, but when classical music w as composed, there w ere a wide variety of other tuning systems in existence. P laying a composi ...

  • Roland RD-700NX - page 70

    71 Detailed Settings for Each Function Changing the Key T ouch (Key T ouch) The setting below allows y ou to adjust the response you get fr om the keyboard when you nger the keys . Paramet er Value Description Key T ouch SPR LIGHT An even lighter setting than LIGHT . LIGHT This sets the keyboard to a light touch. Y ou can achieve fortissimo ( ...

  • Roland RD-700NX - page 71

    72 Detailed Settings for Each Function P edal/[S1] [S2] Buttons Assignments Here ’ s how to change the functions that are assigned to the pedals , the [S1] [S2] buttons, and the sliders. 1. Press the [MENU] button, getting the indica tor to light. The Menu screen appears. 2. Press the C ursor [ ] [ ] buttons to selec t “2.Control. ” 3. Press ...

  • Roland RD-700NX - page 72

    73 Detailed Settings for Each Function Assigning Functions to the [S1] [S2] Buttons (S1/S2 Assign) This setting determines the function of the [S1] and [S2] buttons. Paramet er Value Function/ Paramet er Setting Changed S1/S2 00: OFF No control 01: COUPLE +1OCT Playing a key will also sound an additional note one octave higher . 02: COUPLE -1OCT Pl ...

  • Roland RD-700NX - page 73

    74 Detailed Settings for Each Function Rev erb/Chorus S ettings Here you can edit the rev erb and chorus settings. NO TE Making abrupt changes in the settings values may cause the sound to become distorted or overly loud. Car efully monitor volume levels while making the settings. 1. Press the [MENU] button, getting the indica tor to light. The Men ...

  • Roland RD-700NX - page 74

    75 Detailed Settings for Each Function Setting Chorus and Delay Chorus adds depth and spaciousness to the sound. Y ou can select whether to use this as a chorus eect or a delay eect. Y ou can set the amount of Chorus applied separately f or each individual tone (p. 56). Chorus T ype Y ou can select the chorus type. When you change the Chorus ...

  • Roland RD-700NX - page 75

    76 Detailed Settings for Each Function Making the Compr essor S ettings This is a stereo compr essor (limiter) that is applied to the nal output. With separate settings f or the high-frequenc y range, midrange , and low-frequency range, this reduc es inconsistencies in volume lev els by compressing the sound when the volume ex ceeds a preset vol ...

  • Roland RD-700NX - page 76

    77 Detailed Settings for Each Function File Management Saving a Liv e Set File (LIVE SET Sav e) A single, individual le containing a collection of 100 Live Sets register ed to the RD-700NX is called a “Live Set le. ” This Live Set le can be saved in the RD-700NX’ s internal memory or on USB memory (sold separately) connected to the U ...

  • Roland RD-700NX - page 77

    78 Detailed Settings for Each Function Calling Up Liv e S et Files (LIVE SET L oad) Here ’ s how to load a previously sav ed Live Set le. NO TE The current settings are er ased when a Live Set le is called up. Be sure to sav e you would like to keep rst bef ore calling up (p . 77). 1. Press the [MENU] button, getting the indica tor to li ...

  • Roland RD-700NX - page 78

    79 Detailed Settings for Each Function 4. Press the [LA YER EDIT ] (MEDIA) button t o select the memor y containing the Live Set le y ou want to delete . 5. Use the Cursor [ ] [ ] buttons or the V AL UE dial to select the Live Set le that you w ant to delete , and press the [ENTER] button. The conrmation message appears. If you do not want ...

  • Roland RD-700NX - page 79

    80 Detailed Settings for Each Function Deleting a S ong (SONG Delete) This operation deletes a sav ed song. 1. Press the [MENU] button, getting the indica tor to light. The Menu screen appears. 2. Press the C ursor [ ] [ ] buttons to selec t “5.File, ” then press the [ENTER] button. The Edit screen appears . 3. Press the C ursor [ ] [ ] buttons ...

  • Roland RD-700NX - page 80

    81 Detailed Settings for Each Function F ormatting Memor y (Forma t) “Formatting ” is an operation that returns the internal memory to the factor y-set condition, or prepar es USB memory for use with RD-700NX. USB memory cannot be used with the RD -700NX unless it is formatted suitably for the RD-700NX. If you’ re using newly purchased USB me ...

  • Roland RD-700NX - page 81

    82 Detailed Settings for Each Function Making the Rhythm Settings The RD-700NX features internal drum patt erns complementing Jazz, Rock, and other various musical genres. This k ind of drum pattern is called a “Rhythm. ” 1. Press the [MENU] button, getting the indica tor to light. The Menu screen appears. 2. Press the C ursor [ ] [ ] buttons t ...

  • Roland RD-700NX - page 82

    83 Detailed Settings for Each Function About V-LINK V-LINK ( ) is a func tion that provides f or the play of music and visual material. By using V-LINK-compatible video equipment, visual e ects can be easily linked to, and made part of the expressive elements of a performance. For e xample, if you use the RD-700NX in conjunction with the P-10, y ...

  • Roland RD-700NX - page 83

    84 Detailed Settings for Each Function Changing Settings Related t o Song Playback Y ou can change a variety of settings related to song playback. 1. Press the [MENU] button, getting the indica tor to light. The Menu screen appears. 2. Press the C ursor [ ] [ ] buttons to selec t “8.Utilit y , ” and press the [ENTER] button to displa y the Edit ...

  • Roland RD-700NX - page 84

    85 Detailed Settings for Each Function Restoring the Settings to the F actor y Condition The settings stored in the RD-700NX can be returned to their factory settings. NO TE • Executing “Factory Reset All” results in deletion of the Live Sets (p . 44). If you want to keep the recor ded content, save the Live Set le to your USB memory (p. 7 ...

  • Roland RD-700NX - page 85

    86 C onnec ting Ex ternal MIDI Devices Recording RD-700NX P er formances to an External MIDI Sequencer Now , tr y using an external sequencer to record your music on to multiple tracks, and then play back the r ecorded performance. C onnecting to an Ex ternal Sequencer NO TE T o prevent malfunction and/or damage to speakers or other devices, alway ...

  • Roland RD-700NX - page 86

    87 Connecting External MIDI Devices 3. Set the Rec Setting and Local Control . Use the procedur e described in the previous section “Settings for Recording ” to make the follo wing settings. Paramet er Value Rec Mode ON Local Switch OFF 4. Begin recording with the e xternal sequencer . 5. Perform on the RD-700NX. 6. When the performance is  ...

  • Roland RD-700NX - page 87

    88 Connecting External MIDI Devices Playing the RD-700NX’ s Internal Sound Genera tor fr om an External MIDI Device T r y Playing the RD-700NX from an external MIDI Device. Making C onnec tions NO TE T o prevent malfunction and/or damage to speakers or other devices, alway s turn down the volume, and turn o the power on all devices before maki ...

  • Roland RD-700NX - page 88

    89 Connec ting to a C omputer via the USB MIDI Connector If you use a USB cable (commercially available) t o connect the USB MIDI connector located on the RD-700NX’ s rear panel to the USB connector of your computer , you ’ll be able to do the following things . • Use the RD-700NX to play SMF music  les played back by MIDI- compatible soft ...

  • Roland RD-700NX - page 89

    90 Connecting to Y our Comput er Swit ching USB Drivers The USB driver to be used when a computer is c onnected to the USB connector is determined as follows: 1. Press the [MENU] button. 2. Press the C ursor [ ] [ ] buttons to selec t “0.SYSTEM, ” and then press the [ENTER] button. 3. Press the C ursor [ ] [ ] buttons to switch screens, and pre ...

  • Roland RD-700NX - page 90

    91 Material T roubleshooting If the RD-700NX does not func tion in the way you expect, rst check the f ollowing points. If this does not resolve the pr oblem, consult your dealer or a nearby Roland Ser vice Station. * If cer tain messages appear in the display during operation, please r efer to “Error Messages/O ther Messages” (p . 94). Prob ...

  • Roland RD-700NX - page 91

    92 Material Problem Check/Solution Page Tones Are Altered Did you call up a Live Set? When a Live Set is called up, the current Tone, eect, and other settings are disabled, and the selected Live Set goes into eect. Resave required settings to a Live Set. p. 44 Did you press the ONE TOUCH PIANO button or the ONE TOUCH E. PIANO button? When the ...

  • Roland RD-700NX - page 92

    93 Material Problem Check/Solution Page Pitch is Odd Depending on the Tone selected, pitches played in certain registers will be changed and played at other pitches. – Is Coarse Tune or Fine Tune set for any specic Part? Check the following settings. • TONE EDIT Course Tune, Fine Tune • C.T and F.T setting in MIDI screen p. 54 p. 63 Has th ...

  • Roland RD-700NX - page 93

    94 Material Problem Check/Solution Page The sound of the higher notes suddenly changes from a certain key On an acoustic piano, the approximately one and a half octaves of notes at the top of the keyboard will continue sounding regardless of the damper pedal. These notes also have a somewhat dierent tonal character. RD-700NX faithfully simulate ...

  • Roland RD-700NX - page 94

    95 Material Indication Situation Action Error 30 The internal memory capacity of the RD-700NX is full. The internal memory capacity of the RD -700NX is full. – Error 40 The instrument can ’t deal with the excessiv e MIDI data. The RD-700NX cannot deal with the excessive MIDI data sent from the external MIDI device. Reduce the amount of MIDI dat ...

  • Roland RD-700NX - page 95

    96 Material Eect List MFX 00: THRU 01: EQUALIZER 02: SPEC TRUM 03: ISOLA TOR 04: LOW BOOST 05: SUPER FIL TR 06: STEP FIL TER 07: ENHANCER 08: AUT O W AH 09: HUMANIZER 10: SP .SIMULA TR 11: PHASER 12: STEP PHASER 13: MUL T PHASER 14: INF PHASER 15: RING MODL TR 16: STEP R.MOD 17: TREMOLO 18: AUT O P AN 19: STEP P AN 20: SLICER 21: ROT ARY 22: VK ...

  • Roland RD-700NX - page 96

    97 About the Ivor y F eel Keyboard F eatures of an I vor y F eel keyboar d T raditional piano keys are made from the best materials-ivory (for white keys) and ebon y (for black keys). The Ivor y F eel keyboard uses the latest in technology to repr oduce the touch and feel of these materials . An Ivory Feel keyboard o ers the following fea tures. ...

  • Roland RD-700NX - page 97

    98 Main Specications RD-700NX: Digital Piano (Conf orms to General MIDI 2 Syst em) [Keyboard Section] 88 keys (PHA III Ivory Feel Keyboard with Escapement) [Sound Generator Section] Maximum Polyphon y 128 v oices Parts Live Set (4 layers) +16 parts Sound Generator SuperNA TURAL Piano SuperNA TURAL E. Piano Virtual T one Wheel Organ PCM Sound Gen ...

  • Roland RD-700NX - page 98

    99 A A C I n l e t ........................................................ 12 A T K ............................................................ 63 A t t a c k T i m e ( O  s e t ) ............................................ 55 Audio Volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 B ...

  • Roland RD-700NX - page 99

    100 Index M M a s t e r T u n e ................................................... 67 M a s t e r V o l u m e ................................................. 67 M a x ( V e l o c i t y M a x ) ......................................... 57 , 63 M . D ( M o d u l a t i o n D e p t h ) ....................................... 64 [ M E N U ] B u t t o ...

  • Roland RD-700NX - page 100

    101 Index T T e m p e r a m e n t .................................................. 70 T e m p e r a m e n t K e y ............................................. 70 T e m p o .................................................. 37 , 39 , 82 T e m p o r a r y a r e a ................................................ 20 T o n e ......................... ...

  • Roland RD-700NX - page 101

    102 P ur pose - Oriented Index This index lists the main setting items relevan t to play of the RD-700NX’ s keyboard. V olume S etting Changing the Volume for the entire RD-700NX ............................................. [ V O L U M E ] s l i d e r ( p . 1 8 ) . . . . . . . . . . . . . . . . . [MENU] button 0.System M aster Volume (p . 67) Ch ...

  • Roland RD-700NX - page 102

    103 MEMO ...

  • Roland RD-700NX - page 103

    For the USA DECLARATION OF CONFORMITY Compliance Information Statement Model Name : Type of Equipment : Responsible Party : Address : Telephone : RD-700NX Digital Piano Roland Corporation U.S. 5100 S. Eastern Avenue, Los Angeles, CA 90040-2938 (323) 890-3700 Model Name : Type of Equipment : Responsible Party : Address : Telephone : UA-5 USB Audio I ...

  • Roland RD-700NX - page 104

    For EU Countries For China ...

  • Roland RD-700NX - page 105

    Information When y ou need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below . AFRICA EGYPT 9, EBN Hagar Al Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: (022)-417-1828 REUNION MARCEL FO- Y AM Sarl 25 Rue Jules Hermann, Chaudron - BP79 97 491 Ste Clotilde Cede ...

  • Roland RD-700NX - page 106

    * 5 1 0 0 0 1 6 9 8 3 - 0 2 * ...

Manufacturer Roland Category Electronic Keyboard

Documents that we receive from a manufacturer of a Roland RD-700NX can be divided into several groups. They are, among others:
- Roland technical drawings
- RD-700NX manuals
- Roland product data sheets
- information booklets
- or energy labels Roland RD-700NX
All of them are important, but the most important information from the point of view of use of the device are in the user manual Roland RD-700NX.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Roland RD-700NX, service manual, brief instructions and user manuals Roland RD-700NX. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Roland RD-700NX.

Similar manuals

A complete manual for the device Roland RD-700NX, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Roland RD-700NX by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Roland RD-700NX.

A complete Roland manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Roland RD-700NX - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Roland RD-700NX, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Roland RD-700NX, that we can find in the current document
3. Tips how to use the basic functions of the device Roland RD-700NX - which should help us in our first steps of using Roland RD-700NX
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Roland RD-700NX
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Roland RD-700NX in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Roland RD-700NX?

Use the form below

If you did not solve your problem by using a manual Roland RD-700NX, ask a question using the form below. If a user had a similar problem with Roland RD-700NX it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)