English dropdown-ico

Manual Allstar Products Group 6000

24 pages 1.27 mb
Download

Go to site of 24

Summary
  • Allstar Products Group 6000 - page 1

    1 INST ALLA TION AND OWNER’S MANUAL As of date of manufacture, meets all AN SI/UL 325 Safety Requ irements for Vehicular Garage Door Operators 6000 SERIES Residential V ehicular Garage Door Operator MODELS: 6000, 6500, 650 0-P & J6500 READ THIS MANUAL CAREFULLY BEFORE INSTALLATION OR USE 107063 Serial #: Date Installed: Your Dealer: INSTALLER ...

  • Allstar Products Group 6000 - page 2

    2 Product Fea tures ................................................................................... 2 Component Identif ication/T ools Required ........................................... 4 Section A : A ssembly Instruct ions ....................................................... 5 Section B: Installation Notes ................................ ...

  • Allstar Products Group 6000 - page 3

    3 PRODUCT FE A TURES The purpose of this booklet is to provide ass embly, inst allation and operati on inform ation concerning the 6000 Series Residential Garage Door Openers and related A ccessory Pr oducts. NOTICE IT IS IMPORTANT TH AT THIS INSTRUCTION MANUAL BE READ AN D UNDERSTOOD COMPLETELY BEFORE INSTALLATION OR OPERATIO N IS ATTEMPTED. NOTIC ...

  • Allstar Products Group 6000 - page 4

    4 DOOR ARMS DOOR MOUNTING BRAC KETS SECTIONAL DOORS ONE-PIECE DOORS FRONT IDLER TRO LLEY OUTER HALF CHAIN GUARD WA L L MOUNTING BRAC KET RELE ASE RO PE AND HANDLE OPEN ER HARDW ARE BAG DRIVE CHAIN MAST ER LINKS STEPL ADDER TAPE M EASURE WO O D BLOCK HAMMER TEE RAI L HACKSAW 1/2” OPEN END W RENCH SOCKET W RENCH 3/8” SOC KET 7/16” SOCKET LEVEL ...

  • Allstar Products Group 6000 - page 5

    5 NOTE: The T ee Rail/Chain Assembly is packaged sep arately from the Power Unit. The Inner Trolley half, Front Idler Sprocket, C hain, Restraining Device an d Limit Cams are assembled on the Tee Rail at the factory. Follow the steps outlined belo w to complete assembl y prior to insta llation. Refer to th e component identification illustrations o ...

  • Allstar Products Group 6000 - page 6

    6 WARNING! T O REDUCE THE RISK OF SEVERE INJUR Y OR DEA TH: R EA D A ND FOLL OW ALL INST ALLA TI ON INSTRUCTI ONS! WARNING : AN U N B AL AN C E D D O O R O R ONE TH A T ST ICKS OR BINDS M AY PREVENT THE SEN SING SYST EM FROM WORKING PRO PERLY, CAUSING INJ URY OR DEATH. ENSURE D OOR IS PROPERLY BALANCED AND ELIM INA T E ANY STICKING OR BINDING PRIOR ...

  • Allstar Products Group 6000 - page 7

    7 WARNING SPRINGS, PULLEYS, CA BLES AND MOUNTING HA RDW A RE USED TO BALA NCE YOUR GARAGE DOOR ARE UNDER EXTREME TEN SION AT AL L TIMES AND CAN CAUSE S EVERE INJURY OR DEATH IF DISTURBED. DO NOT ATTEMPT ADJUSTMENT. FRONT MOUNTING BRACKET MUST BE INSTALLED TO A STRUCTURAL SUPPORT (STUD) ON THE HEADER W ALL. FA ILURE TO DO SO COULD CAUSE SENSING SYS ...

  • Allstar Products Group 6000 - page 8

    8 HIGH ARC RISE HIGH ARC RISE HORIZONT AL LINE 4 INCHES 6 INCHES 4 TO 8 INCHE S 11 INCHES 8 TO 12 INCH ES 16 INCHES STEP 1A: M ountin g the Fron t Brack et — One Piece Doors Without Tr ack: Mark a vertical centerline on the header above th e door. Manual ly raise the door to it s high arc posit ion and temporarily clamp in that position. With th ...

  • Allstar Products Group 6000 - page 9

    9 C: INST ALLING THE OPER A TO R STEP 2: Raise the Tee Rail so that the Front Idler Brack et and Front Mounting Bracket align. Insert bolt and tighten nut loosel y f or now. Later in the installation, this nut must be tightened sec urely. STEP 3 — Sectional Doors and One Piece Doors wit h Trac k: Raise the Opener an d rest the Power Unit on a lad ...

  • Allstar Products Group 6000 - page 10

    10 FIBERGLASS, ALUMINUM OR LIGHTWEIGHT STEEL GARAGE DOORS WILL REQUIRE REINF ORCEM ENT B EFORE INSTALLATION OF DOOR MOUNT ING BRACKET. CONTACT YOUR DOOR MANUFACTURER FOR A REINFORCEMENT KI T CA UTION! STEP 6: DOOR ARM CONNECTION AND INSTALLATION NOTE: If the door is of lig ht construction it may be necessary to reinforce the center s tile with stee ...

  • Allstar Products Group 6000 - page 11

    11 WARNING IMPROPER DOOR OPERATION COULD CAUSE INJURY OR DEATH. CAUTION LABEL M UST BE MOUNTED ON WAL L NEAR THE PUSHBUTTON. ALL W ARNINGS AND INSTRUCTIONS ON TH E LABEL SHOULD BE STRICTLY ADHERED TO. STEP 7: T ie a double overhand kno t in one end of the Emerge nc y Relea se Rop e an d slip the o ther e nd thr ough t he red Release Handle, the Rel ...

  • Allstar Products Group 6000 - page 12

    12 DISCONNECT POWER A T FUSE BOX A ND OPENER BEFORE WIRING PERMANENTLY TO PREVENT ELECTROCUTION. WARNING IMPROPER WIRING COULD CA USE ELECTROCUTION OR DAMA GE TO CIRCUITRY. FOLLOW LOCAL BUILDING AND WARNING STEP 9: Consult the label on the rear panel of the Opener to determine its proper working voltage. Nor mally it will be marked for 115V, 60 cy ...

  • Allstar Products Group 6000 - page 13

    13 INSTA L LATION OF 2 WIR E A LL -CLEA R P HOT OSYST EM: STEP 1: Mark the pos ition of the A LL-CL EAR™ Photosys tem as follows: Mark a l ine on the l eft and righ t door jamb (c lo se to the door track ) FOUR (4) inc he s AND SIX (6) inches above the fl oor. The top mark is the maximum h eight and the botto m line is the minimum hei ght that t ...

  • Allstar Products Group 6000 - page 14

    14 A. Attach the"U" brackets to the "L" brackets with a 1/4- 20 carriage bolt, w asher and h ex nut (provided). In sert t he bolt from th e inside of the "U" bracket and hand tighten only at this time. B. Place the transmitter and receiver units into their respective " U" brackets. See Illus tration, at right ...

  • Allstar Products Group 6000 - page 15

    15 WARNING TO PREVENT THE RI SK OF PERSONA L INJUR Y, DAMA GE TO DOOR OR PROPERTY, ON LY OPERA TE DOOR CONTROLS WHEN DOOR IS IN CLEAR VIEW. KEEP REMOTE CONTROL A W AY FROM CHILDREN IN SECURE A RE A . 104386 D: A UXILI A R Y EQUIPMENT Setting The Cod ing Sw itches: When se tting the Coding Sw it ches THE FAC TORY PRE-SET CODES MUST BE CHANGED TO P R ...

  • Allstar Products Group 6000 - page 16

    16 D: A UXILI A R Y EQUIPMENT STEP 3: Push the wire jacket into on e of the tw o notches provided at the ends of the housing, allowing a m aximum of 1/8” inch of the jacket inside the case (too m uch will make mounting difficult). C arefully tuck the loose wires into the case and mount the un it usin g the sc rews p rovid ed. STEP 4: Run the wire ...

  • Allstar Products Group 6000 - page 17

    17 IF LIM ITS ARE N OT ADJ USTE D PROPERLY, THE EMERG ENCY RELEASE MECH AN ISM M AY NOT WORK PROPERLY A ND DOOR OPERA TION CO ULD RES ULT IN D OOR DA MAGE, SERIOUS PERSO NA L INJURY OR DEA TH! WARNING T O REDUCE THE RISK OF SEVERE INJUR Y OR DE A TH, RE AD A ND FOLLOW ALL INSTR UCTIONS ! W ARNING IMPORT ANT S AFETY INSTRUCTIONS • NEVER let childr ...

  • Allstar Products Group 6000 - page 18

    18 STEP 2: Adjusting the Se nsitivity Force — Sensitivity System force adjustment s crews are located on the side rails of th e Po w er Unit and can easily be adjusted with a screwdriver. Turn the screws CLOCKW ISE f or more f orce and COUNTERCLOCKWI SE for l ess fo rce . STEP 3: Testing the Sensitivity Force — To test the Sensi tivi ty S ystem ...

  • Allstar Products Group 6000 - page 19

    19 A D AMAGED OR MALFUNCTIONING PHOTOELECTRIC A CCESS ORY SYSTEM COULD ENA BLE A GARAGE DOOR TO CLOSE ON PEOPLE OR PROPERTY, CA USING SERIOUS INJURY OR DE A TH. PERFORM THIS TEST MONTHLY TO ENSURE YOUR ALL-CLE AR IS WORKING PROPERLY . STEP 6 : Operating the Super Sta tion (Deluxe Wall Pushb utton Sta tion) Co ntrols — The Super Station replaces s ...

  • Allstar Products Group 6000 - page 20

    20 For Opener Models: 6000 , 6500, 65 00-P and J6500 108389 OPERA TOR WIRING DI AGRA M ...

  • Allstar Products Group 6000 - page 21

    21 Your 6000 Seri es Residential G arage Door Opener is furnishe d with an enhanced 2 Wire Al l-Clear™ Pho tos yst em. Ne w fea tur es incl ude : Time- Saving Elec trica l Connect ion s. No screw terminals! Just strip the ends of th e wires back 5/16 inch and use the suppl ied wire nut connectors for a quick hook-u p to pre-wired garages or to th ...

  • Allstar Products Group 6000 - page 22

    22 BEFORE PLACING D OOR OPERATOR IN REGULAR SERVICE , MAKE SURE TH AT: 1. T HE FRONT AND REAR MOUNTS FOR THE OPENER ARE SOUND AND SECURE AND TH E RAIL IS POSITIONED CORRECT LY ABOVE T HE HIGH ARC OF THE DOOR, AND THAT THE OPENER IS POSITIONED OV ER THE DOOR ACTION CENTER LINE. 2. FOR S ECTIONAL DOORS AND ONE- PIECE DOORS WITH TRACKS, THE POSIT ION ...

  • Allstar Products Group 6000 - page 23

    23 USE EXTREME CAUTIO N AT ALL T IMES WHEN ATTEMPTING TO DIAGNOSE A ND R ECTIFY PROB LEMS WIT H Y OUR GARA G E DOOR OPE NER . BEFOR E AT TEMPT ING A NY SERVIC E ON U N IT, DIS C ONNE CT OPENE R FR OM POWE R SUP PLY . YOUR GA RA GE D OOR IS TH E LA RGE ST MOVIN G OB JEC T IN YOU R HOUSE, A ND THE SPRING S, PULLEYS, CABLES AND MOUNTING HARDW ARE UTIL ...

  • Allstar Products Group 6000 - page 24

    24 c.p. A llstar Corporation Downingtown, P A 19335 This garage d oor operator is built in t he USA and complies with all requir ements of Underwriters Laboratories S tandard UL-325. P/N 108391 Rev . C, 2/99 Manufacturer ’s Limi ted Warranty Allstar war rants its 6000 S eries re sident ial v ehicula r garag e door operato rs as follow s: A. The d ...

Manufacturer Allstar Products Group Category Garage Door Opener

Documents that we receive from a manufacturer of a Allstar Products Group 6000 can be divided into several groups. They are, among others:
- Allstar Products Group technical drawings
- 6000 manuals
- Allstar Products Group product data sheets
- information booklets
- or energy labels Allstar Products Group 6000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Allstar Products Group 6000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Allstar Products Group 6000, service manual, brief instructions and user manuals Allstar Products Group 6000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Allstar Products Group 6000.

Similar manuals

A complete manual for the device Allstar Products Group 6000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Allstar Products Group 6000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Allstar Products Group 6000.

A complete Allstar Products Group manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Allstar Products Group 6000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Allstar Products Group 6000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Allstar Products Group 6000, that we can find in the current document
3. Tips how to use the basic functions of the device Allstar Products Group 6000 - which should help us in our first steps of using Allstar Products Group 6000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Allstar Products Group 6000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Allstar Products Group 6000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Allstar Products Group 6000?

Use the form below

If you did not solve your problem by using a manual Allstar Products Group 6000, ask a question using the form below. If a user had a similar problem with Allstar Products Group 6000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)