English dropdown-ico

Manual JAI CV-M30

21 pages 0.99 mb
Download

Go to site of 21

Summary
  • JAI CV-M30 - page 1

    Monochrome Double Speed Camera CV-M30 Operation Manual Camera: Revision D Manual: Version 1.0 CV-M30manDMay12.doc JPT 12 -05- 03 ...

  • JAI CV-M30 - page 2

    CV-M30 Table of Contents 1. General ........................................................................................................ 2 2. Standard Co mposition ...................................................................................... 2 3. Main Features ............................................................................ ...

  • JAI CV-M30 - page 3

    CV-M30 1. General The CV-M30 camera revision D is an updated version with a new CCD sensor I CX-418ALL-6 with improved specifications. The revisio n D ca mera can only operate in dou ble speed. CV-M30 is a monochrome CCD video camera designed for in dustrial video sensing applications. The camera operates with double speed scanning, where the horiz ...

  • JAI CV-M30 - page 4

    CV-M30 4. Locations and Functions Fig. 1. Locations 1. 1/2” interline-transfer type CCD sensor 2. Lens mount for C-mount lenses. *1) 3. BNC connector for video output 4. Switch block SW1 for shutter speed and function mode setting 5. 6-Pin connector for Input/output of control signals 6. 12-Pin connector for 12V DC p ower and external sync signal ...

  • JAI CV-M30 - page 5

    CV-M30 5. Pin Assignment 5.1. 12-pin Multi-connector (DC- IN/VIDEO OUT, EXT.HD/VD IN) Type: HR10A-10R-12PB-01 (Hirose) male Seen from rear. Fig. 2. 12 pin connector 5.2. 6-pin Multi-connector (TRIGGER) Type: HR10A-7R-6PB (Hirose) male Pin no Signal Remarks 1 GND 2 +12 V DC input 3 GND 4 Video output Parallel with the BNC connector. *1) 5 GND 6 HD i ...

  • JAI CV-M30 - page 6

    CV-M30 5.3. Input and Output Diagram Fig. 4. WEN and EEN output Fig. 5. HD and VD/Trigg er input - 5 - ...

  • JAI CV-M30 - page 7

    CV-M30 6. Functions and Operations 6.1. Input of External HD/VD Signals As factory setting the camera can be synchron ized by external HD/VD signals. The external supplied HD/VD signal should follow the same standa rd as the camera setting for spe ed, scanning and interlace. The signal level must be 4.0 Vp-p ± 2.0V with 75 Ohm termination on. The ...

  • JAI CV-M30 - page 8

    CV-M30 6.3.1. Edge Pre-select Mode The edge pre-select mode will work in non-interlaced and f ield accumulation mode with partial scanning and double speed. The CV-M30 starts th e exposure (= accumulation of photoelectric charge) at the first HD pulse after the falling edge of the ext. trigger pulse. The exposure ends after the time set by the 3 sh ...

  • JAI CV-M30 - page 9

    CV-M30 6.3.2. Pulse Width Co ntrol Mode The pulse width control mode will only work in non-interlaced field accumulation mode. The exposure is controlled by the low period of the ext. trigger pulse. The CV-M30 starts the exposure at the first HD pulse after the falling edge of the ext. trigger pulse. The exposure ends at the first HD pulse after th ...

  • JAI CV-M30 - page 10

    CV-M30 6.4. Other Functions 6.4.1. Double Speed Mode The CV-M30 camera revision D operates only with double speed scannin g. Double speed is 120 fields per second. (V= 119.88Hz. H=31.468 kHz). To use this mode. Set: 6.4.2. Partial Scanning Mode To obtain a higher frame rate, the partial scanning can be used. In this mode only the vertical center pa ...

  • JAI CV-M30 - page 11

    CV-M30 6.5.2. External Sync Mode H = 31.778 µ s Fig. 10. Vertical timing with external sync 6.5.3. External Sync Mode. Partial Scan H = 31.778 µ s H = 31.778 µ s Fig. 11. Partial scanning vertical timing with external sync - 10 - ...

  • JAI CV-M30 - page 12

    CV-M30 6.5.4. Edge Pre-select H = 31.778 µ s Fig. 12. Vertical timing for Edge pre -select 6.5.5. Edge Pre -select. Partial Scan H = 31.778 µ s Fig. 13. Vertical timing for Edge pre-select 1/2 partial scanning H = 31.778 µ s Fig. 14. Vertical timing for Edge pre-select 1/3 partial scanning - 11 - ...

  • JAI CV-M30 - page 13

    CV-M30 6.5.6. Pulse Width Co ntrol H = 31.778 µ s Fig. 15. Vertical timing for pulse width control 6.5.7. Pulse Width. Partial Scan H = 31.778 µ s Fig. 16. Vertical timing for puls e width control 1/2 partial scanning H = 31.778 µ s Fig. 17. Vertical timing for puls e width control 1/3 partial scanning - 12 - ...

  • JAI CV-M30 - page 14

    CV-M30 7. Mode Setting 7.1. Switch SW1 on Rear Panel 7.1.1. SW1 Lay-out < < < < < > < > < < > > > < < > < > > > < > > > Off 1/200 1/500 1/1000 1/2000 1/4000 1/10,000 1/20,000 OFF ON GAIN SCAN mode 1 SHUTTER < > < > < > < > < < > > AGC MAN 2:1 ...

  • JAI CV-M30 - page 15

    CV-M30 7.1.4. Scan Mode Settings With SW1-4 and SW1-6 the scanning mode can be selected. The table sh ows the modes. SW1-4 SW1-6 Function Mode Remarks OFF OFF 2:1 Interlaced mode In Normal trigger mode only. (Continuous). ON OFF 1/2 partial scan Non-interlaced only OFF ON Non-interlaced mode ON ON 1/3 partial scan Non-interlaced only For detail, pl ...

  • JAI CV-M30 - page 16

    CV-M30 7.2. Internal Switch and Jumper Settings Inside the camera there are switches for 75 termination of external trigger/VD and HD and for trigger mode select. There are also jumpers for gamma select. 7.2.1. Trigger/VD and HD Termination On the PK8212 board switch SW1 for 75 Ohm terminat ion of external trigger/VD and HD is found. SW1-1 is for e ...

  • JAI CV-M30 - page 17

    CV-M30 8. Internal Adjustme nts of Video Si gnal For adjustment of the video output signal there are internal potentiome ters on th PK 7987A board. Adjustment should only be done in a setup with a standard test chart and controlled illumination Do not touch these potentiometers unless you are familiar with camera adjustments. VR 1 is for AGC level ...

  • JAI CV-M30 - page 18

    CV-M30 9. External Appearance and Dimensions Fig. 22. Outline - 17 - ...

  • JAI CV-M30 - page 19

    CV-M30 10. Specifications 10.1. Specification table Model CV-M30 CCD Sensor 1/2”Monochrome IT CCD. Sony ICX -418ALL-6 Image Area 6.45mm (H) x 4.84mm (V) Effective Pixels 768(H) x 494(V) Cell Size 8.4 µ m(H) x 9.8 µ m(V) Pixels in video output Double Speed 2:1 interlaced Non-interlaced 1/2 partial 1/3 partial 756(h) x 485(v) 60 frames/sec 756(h) ...

  • JAI CV-M30 - page 20

    CV-M30 11. Appendix 11.1. Precautions Personnel not trained in dealing with similar elec tronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostatic sensitive components. Do not attempt to disassemble this camera. Do ...

  • JAI CV-M30 - page 21

    CV-M30 12. Users Record Camera type: CV-M30 Revision: (Revision D) Serial No. …………….. For camera revision history, please contact your local JAI distributor. Users Mode Settings. Users Modifications. DECLARATION OF CONFORMITY AS DEFINED BY THE COUNCIL DIRECTIVE 89/336/EEC EMC (ELECTROMAGNETIC COMPABILITY) WE HEREWITH DE CLARE THAT THIS PR ...

Manufacturer JAI Category Security Camera

Documents that we receive from a manufacturer of a JAI CV-M30 can be divided into several groups. They are, among others:
- JAI technical drawings
- CV-M30 manuals
- JAI product data sheets
- information booklets
- or energy labels JAI CV-M30
All of them are important, but the most important information from the point of view of use of the device are in the user manual JAI CV-M30.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals JAI CV-M30, service manual, brief instructions and user manuals JAI CV-M30. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product JAI CV-M30.

Similar manuals

A complete manual for the device JAI CV-M30, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use JAI CV-M30 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of JAI CV-M30.

A complete JAI manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual JAI CV-M30 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the JAI CV-M30, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the JAI CV-M30, that we can find in the current document
3. Tips how to use the basic functions of the device JAI CV-M30 - which should help us in our first steps of using JAI CV-M30
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with JAI CV-M30
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of JAI CV-M30 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning JAI CV-M30?

Use the form below

If you did not solve your problem by using a manual JAI CV-M30, ask a question using the form below. If a user had a similar problem with JAI CV-M30 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)