English dropdown-ico

Manual Interfire Audio A1100.2

17 pages 3.67 mb
Download

Go to site of 17

Summary
  • Interfire Audio A1100.2 - page 1

    2 CHANNEL / 4 CHANNEL / 5 CHANNEL AUTOMOTIVE AMPLIFIER INSTRUCTION MANUAL A300.2 / A500.2 / A700.2 A1000.2 / A1100.2 / A2200.2 A500.4 / A700.4 / A900.4 / A800.5 ...

  • Interfire Audio A1100.2 - page 2

    1 free installation. • Four Class ''AB'' High-Current Dual Discrete Drive Stages. • Class ''AB'' T echnology MOSFET PWM Power Supply . • Bridgeable & TRI-Mode Operation. • Continuously V ariable 12dB/Octave High Pass & 12dB /Octave Low Pass Crossover. • Subwoofer V ariable Crossover for Deep ...

  • Interfire Audio A1100.2 - page 3

    • NEVER operate the amplifier without the proper power and ground wire, 10 gauge minimum. • NEVER operate the amplifier without proper fusing. Fuse holder must be located with in 0.5 meters from the battery . This fuse is to protect the car not the electronics. In case of a short, the fuse will blow instead of the wire burning up. Using other t ...

  • Interfire Audio A1100.2 - page 4

    1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier as a template for drilling. It is very easy to damage the amplifier surface ...

  • Interfire Audio A1100.2 - page 5

    It is important to have good quality power and ground connections. Remember , to complete an electrical circuit, the ground connection is just as important as the positive power connection. Before any power connections are made, disconnect the ground cable at the When the power supply lead, memory backup lead or ground lead are extended use a 5mm² ...

  • Interfire Audio A1100.2 - page 6

    5 FIG.2 +12V REM GND AUTO - ANTENNA LEAD CH1 CH2 CAR STEREO HEAD UNIT LINE INPUT GAIN BASS L.P.F L.P.F H.P.F H.P.F 6V 0.2V 0dB 12dB 50Hz 250Hz FLAT 80Hz 1.2KHz CROSSOVER CH1 CH2 ...

  • Interfire Audio A1100.2 - page 7

    6 CH3 CH4 CH2 CH1 +12V REM GND AUTO - ANTENNA LEAD CAR STEREO HEAD UNIT FIG.2 LINE INPUT LINE INPUT GAIN GAIN BASS BASS CROSSOVER CROSSOVER 6V 0.2V 0dB 12dB 50Hz 500Hz FLAT L.P.F H.P.F FLAT L.P.F H.P.F CH1 CH2 CH3 CH4 50Hz 500Hz 0dB 12dB 6V 0.2V CH 1/2 CH 3/4 ...

  • Interfire Audio A1100.2 - page 8

    7 CH3 CH4 CH2 CH1 CH5 CH6 +12V REM GND AUTO - ANTENNA LEAD CAR STEREO HEAD UNIT FIG.2 6V 0.2V FLAT L.P.F 250Hz 50Hz 1.2kHz 80Hz 1.2kHz 80Hz 250Hz 50Hz H.P.F GAIN CH 1/2 LINE INPUT GAIN L.P.F L.P.F H.P.F H.P.F FLAT LINE INPUT CH1 CH2 CH3 CH4 CROSSOVER CROSSOVER 6V 0.2V FLAT 250Hz 50Hz 1.2kHz 80Hz 6V 0.2V CH5 CH6 CH 5 CH 3/4 ...

  • Interfire Audio A1100.2 - page 9

    POWER B+ GND REM FUSE SPEAKER CH1 (+) (+) ON PROTECT BRIDGED CH2 POWER B+ GND REM FUSE SPEAKER CH1 (+) (+) ON PROTECT BRIDGED CH2 POWER B+ GND REM FUSE SPEAKER CH1 (+) (+) ON PROTECT BRIDGED CH2 This amplifier can operate in one, two or three channel mode. The minimum impedance for single channel (bridged/mono) operation is 4 or 8 ohms. Tri channel ...

  • Interfire Audio A1100.2 - page 10

    CH2 POWER B+ GND REM FUSE SPEAKER (+) (+) (+) (+) CH4 CH3 ON PROTECT CH1 BRIDGED BRIDGED 2 S PEAKER BRIDGED 2 S PEAKER + 1 SUBWOOFER 4 S PEAKER STEREO 6 S PEAKER HEX MODE 9 2-4 Ohms 4 CH 5 CH 4-8 Ohms 6 CH 4-8 Ohms FIG.3 CH2 POWER B+ GND REM FUSE SPEAKER (+) (+) (+) (+) CH4 CH3 ON PROTECT CH1 BRIDGED BRIDGED 3 CH SUB WOOFER 4-8 Ohms 2 CH 1CH 2-4 Oh ...

  • Interfire Audio A1100.2 - page 11

    4-8 Ohms 1 CH 2 CH BRIDGED BRIDGED POWER B+ GND REM FUSE SPEAKER (+) CH4 (+) CH5 (+) CH3 ON PROTECT (+) CH1 (+) CH2 BRIDGED BRIDGED POWER B+ GND REM FUSE SPEAKER (+) CH4 (+) CH5 (+) CH3 ON PROTECT (+) CH1 (+) CH2 BRIDGED BRIDGED POWER B+ GND REM FUSE SPEAKER (+) CH4 (+) CH5 (+) CH3 ON PROTECT (+) CH1 (+) CH2 2-8 Ohms 3 C H 3 S PEAKER BRIDGED 10 5 S ...

  • Interfire Audio A1100.2 - page 12

    11 1.Set to the "H.P .F" position when the amplifier is used to drive a tweeter/midrange system. The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency 2.Set to the "L.P .F" position when the amplifier is used to dri ...

  • Interfire Audio A1100.2 - page 13

    12 ...

  • Interfire Audio A1100.2 - page 14

    13 ...

  • Interfire Audio A1100.2 - page 15

    14 This section provides you with a catalog of amplifier symptoms and their probable causes and solutions. Before you consult this listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e. g. headlights, windows, etc.) Still function correctly . No Audio Low or N.C Remote Tu rn-on conne ...

  • Interfire Audio A1100.2 - page 16

    AMPLIFIER 4 OHMS @ 0.05% THD 4 OHMS Bridged 0.5% THD LOW P ASS FILTE R HIGH PA SS FILT ER MAXIMUM OUTPUT POWER FUSE RAT ING FREQUENCY RESPONSE (-1dB) SIGNAL TO NOISE RAT IO (`A' WTD) INPUT SENSITIVITY INPUT IMPEDANCE OPERATIO N VOLTA GE (NEGAT IVE GROUND) SPEAKER IMPEDANCE @ STEREO DRIVEN DIMENSIONS (W mm x H mm x D mm ) A300.2 75W x 2 150W x ...

  • Interfire Audio A1100.2 - page 17

    AMPLIFIER 4 OHMS @ 0.05% THD 4 OHMS Bridged 0.5% THD LOW P ASS FILTE R HIGH PA SS FILT ER MAXIMUM OUTPUT POWER FUSE RAT ING FREQUENCY RESPONSE (-1dB) SIGNAL TO NOISE RAT IO (`A' WTD) INPUT SENSITIVITY INPUT IMPEDANCE OPERATIO N VOLTA GE (NEGATIV E GROUND) SPEAKER IMPEDANCE @ STEREO DRIVEN DIMENSIONS (W mm x H mm x D mm ) 250x59x280 250x59x320 ...

Manufacturer Interfire Audio Category Stereo Amplifier

Documents that we receive from a manufacturer of a Interfire Audio A1100.2 can be divided into several groups. They are, among others:
- Interfire Audio technical drawings
- A1100.2 manuals
- Interfire Audio product data sheets
- information booklets
- or energy labels Interfire Audio A1100.2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Interfire Audio A1100.2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Interfire Audio A1100.2, service manual, brief instructions and user manuals Interfire Audio A1100.2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Interfire Audio A1100.2.

Similar manuals

A complete manual for the device Interfire Audio A1100.2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Interfire Audio A1100.2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Interfire Audio A1100.2.

A complete Interfire Audio manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Interfire Audio A1100.2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Interfire Audio A1100.2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Interfire Audio A1100.2, that we can find in the current document
3. Tips how to use the basic functions of the device Interfire Audio A1100.2 - which should help us in our first steps of using Interfire Audio A1100.2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Interfire Audio A1100.2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Interfire Audio A1100.2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Interfire Audio A1100.2?

Use the form below

If you did not solve your problem by using a manual Interfire Audio A1100.2, ask a question using the form below. If a user had a similar problem with Interfire Audio A1100.2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)