English dropdown-ico

Manual Harbor Freight Tools 93380

35 pages 4.69 mb
Download

Go to site of 35

Summary
  • Harbor Freight Tools 93380 - page 1

    10” TIL TING ARBOR, CABINET T ABLE SA W Model 93380 ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camar illo , CA 93011 Visit our W eb site at: http://www .harborfreight.com T O PREVENT SERIOUS INJUR Y , READ AND UNDERST AND ALL W ARNINGS AND INSTRUCTIONS BEFORE USE. Copyright © 2005 by Harbor F reight T ools ® . All r ights r ...

  • Harbor Freight Tools 93380 - page 2

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 2 GENERAL SAFETY RULES W ARNING! READ AND UNDERST AND ALL INSTR UCTIONS F ailure to foll o w all instructions listed below ma y result in electric shoc k, fire, and/or serious injury . SA VE THESE INSTR UCTIONS SA VE THIS MANU AL Y ou will need this manual f or the safety warnings ...

  • Harbor Freight Tools 93380 - page 3

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 3 3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. ELECTRICAL SAFETY 4. Grounded tools must be plugg ...

  • Harbor Freight Tools 93380 - page 4

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 4 12. Remo ve adjusting keys or wrenches bef ore turning the power tool on. A wrench or a key that is left attached to a rotating part of the pow er tool ma y result in personal injury . 13. Do not o verreach. K eep proper footing and balance at all times. Proper f ooting and balan ...

  • Harbor Freight Tools 93380 - page 5

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 5 22. Use only accessories that are recommended by the manufacturer for your model. Accessories that ma y be suitable f or one tool ma y become hazardous when used on another tool. SER VICE 23. T ool service must be perf ormed only by qualified repair per sonnel. Ser vice or mainte ...

  • Harbor Freight Tools 93380 - page 6

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 6 7. Alwa ys use Sa w Blades (not included) with a 10” diameter , 5/8” r ound arbor hole , and rated at 4150 RPM or greater . Saw Blades that do not match the mounting hardw are of the T ab le Saw or that are r ated less than the required minimum RPM will run eccentr ically cau ...

  • Harbor Freight Tools 93380 - page 7

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 7 25. Alwa ys unplug the T able Sa w fr om its electrical outlet before perf orm- ing inspection, maintenance, c leaning procedures, or changing accesso- ries. 26. Bef ore trying ne w or complicated techniques, stud y the pr ocedure , and practice with scrap w ood. 27. Make sure th ...

  • Harbor Freight Tools 93380 - page 8

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 8 bac k as the T a ble Sa w is restar ted. * Suppor t lar ge panels with roller stands (not included) to minimiz e the risk of Sa w Blade pinc hing and kic kbac k. Large panels tend to sag under their own w eight. Suppor t s must be placed under the panel and near the outer edge of ...

  • Harbor Freight Tools 93380 - page 9

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 9 36. W ARNING! Some dust created b y po wer sanding, sawing, g r inding, drilling, and other construction activities , contain chemicals kno wn (to the State of Cali- f or nia) to cause cancer , bir th def ects or other reproductive harm. Some e x- amples of these chemicals are: l ...

  • Harbor Freight Tools 93380 - page 10

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 10 resistance path to carry electr icity a way from the user , reducing the risk of elec- tric shock . (See Figure A.) 2. The g rounding prong in the plug is connected through the green wire inside the cord to the g rounding system in the tool. The g reen wire in the cord m ust be ...

  • Harbor Freight Tools 93380 - page 11

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 11 5. If you are using an e xtension cord outdoors , make sure it is mark ed with the suffix “W -A” (“W” in Canada) to indicate it is acceptable f or outdoor use. 6. Make sure y our e xtension cord is properly wired and in good electrical condition. Alw ays replace a damage ...

  • Harbor Freight Tools 93380 - page 12

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 12 UNP A CKING When unpac king both box es, check to mak e sure all the par ts shown on the P ar ts Lists on pages 31, 33, and 34 are included. If any par ts are missing or brok en, please call Harbor F reight T ools at the number sho wn on the cov er of this manual as soon as pos- ...

  • Harbor Freight Tools 93380 - page 13

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 13 2. Open the Motor Cov er (2), and remove the f our Scre ws at the bottom of the Cabinet (1). Then, remo ve the large steel plate from the bottom of the Cabinet. (See Figures D and E.) 3. After removing the large steel plate, y ou will find tw o Cap Bolts were screwed through the ...

  • Harbor Freight Tools 93380 - page 14

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 14 ASSEMBL Y INSTR UCTIONS NO TE: F or additional inf or mation regarding the par ts listed in the f ollo wing pages, r ef er to the Assembl y Di a grams on pag es 32, 33, and 34 . 1. CA UTI ON ! Alw ays make sure the P ower Switch (137) of the T a b le Sa w is in its “OFF” pos ...

  • Harbor Freight Tools 93380 - page 15

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 15 T o Install The Clean Out Door And Dust Hood: 1. Mount the Clean Out Door (12) into the square hole located on the lower left side of the Cabinet (1). (See Figure H.) 2. Attach the Dust Hood (14) to the Clean Out Door (12), using four Self-T apping Screws (13). (See Figure H.) 3 ...

  • Harbor Freight Tools 93380 - page 16

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 16 T o Attac h The Hand Wheels: 1. Line up the K e y (67) on the Shaft (69) with the keyw ay slot in the Hand Wheel (28), and slide the Hand Wheel onto the Shaft. (See Figure J. ) 2. Tighten the Set Screw (29) on the Hand Wheel’ s hub to hold the Hand Wheel securely in place. (Se ...

  • Harbor Freight Tools 93380 - page 17

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 17 top of the Main T able . (See Figure L.) 4. Chec k to make sure the Sa w Blade will not come into contact with the T a b le Inser t (116A or 116B). P osition the Sa w Blade at 90. Then, raise and low er th e Saw Blade through its full r ange of motion. Also, rotate the Saw Blade ...

  • Harbor Freight Tools 93380 - page 18

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 18 ST AND ARD T ABLE INSER T (116A) SET SCREW (117A) SET SCREW (117B) SET SCREW (117A) SET SCREW (117B) FIGURE L T o Install The Blade Guar d Assemb l y: 1. Thread the blade guard Shaft (74) into the hole in the Bac k T r unnion (75) located at the rear of the T a b le Sa w , and f ...

  • Harbor Freight Tools 93380 - page 19

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 19 4. T empor ar ily remov e the T a b le Inser t (116A, 116B). (See Figure N.) 5. Inser t the front tab of the Splitter (315) through the tab le inser t opening in the Main T a b le (115). Loosen the He x Cap Scre w in the inser t opening in the Main T a b l e . Inser t the front ...

  • Harbor Freight Tools 93380 - page 20

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 20 SCREW (135) POWER SWITCH (137) ON OFF FIGURE O ADJUSTMENTS T o Adjust The Splitter And Blade Guar d Assemb l y: 1. Set a machinist’ s square against the f ace of the Splitter (315). Slightly rotate the rear brack et to adjust the f ace of the Splitter per pendicular to the Mai ...

  • Harbor Freight Tools 93380 - page 21

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 21 4. If the Splitter (315) is to the right of the Saw Blade, add washers between the Splitter and the front mounting brack et. Then, adjust the rear Splitter suppor t. (See Figure R.) FIGURE R 5. Recheck the Splitter (315) alignment to the Saw Blade and to the Main T ab le (115) t ...

  • Harbor Freight Tools 93380 - page 22

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 22 V -BELTS (40) SET SCREW (39) MO T OR PULLEY (38) MO T OR (34) SHAFT FIGURE T 10. Recheck the Blade Guard Assembly alignment to the Saw Blade and the Main T a b le (115) top . If the Blade Guard Assembly is properly aligned reattach the Main T a b l e , Left Wing (113), and Right ...

  • Harbor Freight Tools 93380 - page 23

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 23 5. If the Saw Blade is not at 90 degrees, open the Motor Cover (2) to expose the Geared T r unnion (52). Loosen the Nut (51) on the Geared T runnion, and tur n the adjusting stop Bolt (50) in or out. The adjusting stop Bolt should stop against the Geared T runnion when the Saw B ...

  • Harbor Freight Tools 93380 - page 24

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 24 side of the Sa w Blade to the r ight T -Slot edge in the Main T able (115) using a combination square. Make sure to measure between the teeth, not on the tooth. (See Figure V . ) 4. Rotate the Saw Blade toward the front so that the marked tooth is just above the T a b le Inser t ...

  • Harbor Freight Tools 93380 - page 25

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 25 2. W ARNING! When using the Rip Fence assembly (1B thr u 27B), alw ays keep hands and fingers well away from the Saw Blade and cutting area. 3. Set the Rip F ence assembly (1B thr u 27B) on the Right Wing (114) of the T ab l e Saw . (See Figure X.) 4. Adjust the Rip Fence assemb ...

  • Harbor Freight Tools 93380 - page 26

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 26 9. Ne v er attempt to remov e material stuck in the moving par ts of the T able Sa w while it is plugged in and running. 10. T ur n off the T a b le Saw if the wo r kpiece is to be back ed out of an uncompleted cut. 11. When the cut is complete, depress the red “OFF” Button ...

  • Harbor Freight Tools 93380 - page 27

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 27 4. Set the Miter Gauge assembly (200 thru 214) on the Left Wing (113) of the T ab l e Saw . (See Figure Y . ) 5. Operate the Miter Gauge assembly (200 thru 214) by loosening the Knob (200), and turning the Miter Gauge Body (202) to the desired angle of cut. (See Figure Y . ) 6. ...

  • Harbor Freight Tools 93380 - page 28

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 28 3. Before each use, inspect the Saw Blade. Using a dull Saw Blade will cause excessiv e w ear on the Motor of the T able S a w and will not produce a satisf actor y cut. Replace with a new Saw Blade when needed. 4. Before each use, open the Clean Out Door (12) and check for clea ...

  • Harbor Freight Tools 93380 - page 29

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 29 10. CA UTION! All maintenance , service, or repair s not mentioned in this manual must only be performed by a qualified service technician. 1/2” BOL T (35) MOT OR (34) V -BEL T (40) MO T OR PULLEY (38) FIGURE Z PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF ACTURER AND/OR DIS ...

  • Harbor Freight Tools 93380 - page 30

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 30 TR OUBLESHOO TING TROUBLE POSSIBLE REASON SOLUTION 1. Allow Motor to cool and reset by turning P ower Switch to “ON” ...

  • Harbor Freight Tools 93380 - page 31

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 31 P AR TS LIST t r a Pn o i t p i r c s e D. y t Qt r a Pn o i t p i r c s e D. y t Qt r a Pn o i t p i r c s e D. y t Q 1t e n i b a C1 0 5t l o B1 6 9g n i R p a n S1 2r e v o C r o t o M1 1 5t u N1 7 9g n i r a e B d e l a e S2 3b o n K1 2 5n o i n n u r T d e r a e G1 8 9r a l ...

  • Harbor Freight Tools 93380 - page 32

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 32 ASSEMBL Y DIAGRAM NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not a vailab le individually as replacement par t s. ...

  • Harbor Freight Tools 93380 - page 33

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 33 P ARTS LIST AND ASSEMBL Y DIA GRAM (CONT .) NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not a vailab le individually as replacement par t s. P a r t # D e scr i p tio n P a r t # D e sc r i pt io n 200 Kn ob 301 Pi vo t Pi n 201 Flat Washer ...

  • Harbor Freight Tools 93380 - page 34

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 34 P ARTS LIST AND ASSEMBL Y DIA GRAM (CONT .) 1B 2B 3B 4B 5B 6B 7B 8B 9B 10B 11B 12B 13B 14B 15B 16B 17B 27B 26B 25B 24B 23B 22B 21B 20B 19B 18B NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not a vailab le individually as replacement par t s. ...

  • Harbor Freight Tools 93380 - page 35

    SKU 93380 For technical questions, please call 1-800-444-3353. Page 35 PO WER SWITCH SCHEMA TI C ...

Manufacturer Harbor Freight Tools Category Saw

Documents that we receive from a manufacturer of a Harbor Freight Tools 93380 can be divided into several groups. They are, among others:
- Harbor Freight Tools technical drawings
- 93380 manuals
- Harbor Freight Tools product data sheets
- information booklets
- or energy labels Harbor Freight Tools 93380
All of them are important, but the most important information from the point of view of use of the device are in the user manual Harbor Freight Tools 93380.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Harbor Freight Tools 93380, service manual, brief instructions and user manuals Harbor Freight Tools 93380. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Harbor Freight Tools 93380.

Similar manuals

A complete manual for the device Harbor Freight Tools 93380, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Harbor Freight Tools 93380 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Harbor Freight Tools 93380.

A complete Harbor Freight Tools manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Harbor Freight Tools 93380 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Harbor Freight Tools 93380, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Harbor Freight Tools 93380, that we can find in the current document
3. Tips how to use the basic functions of the device Harbor Freight Tools 93380 - which should help us in our first steps of using Harbor Freight Tools 93380
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Harbor Freight Tools 93380
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Harbor Freight Tools 93380 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Harbor Freight Tools 93380?

Use the form below

If you did not solve your problem by using a manual Harbor Freight Tools 93380, ask a question using the form below. If a user had a similar problem with Harbor Freight Tools 93380 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)