English dropdown-ico

Manual Heatiator ADI60S

41 pages 1.84 mb
Download

Go to site of 41

Summary
  • Heatiator ADI60S - page 1

    1 Heatilator • ADI60S • 345-900 Rev . G • 9/08 Model: ADI60S • Do not store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - Do not try to light any appliance - Do not touch any electrical switch. Do not use any phone in your building. - Immediately c ...

  • Heatiator ADI60S - page 2

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 2 Congratulations Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on appliance: ____________________ Dealership purchased from: ________________ ...

  • Heatiator ADI60S - page 3

    3 Heatilator • ADI60S • 345-900 Rev . G • 9/08 T able of Contents 1 Listing and Code Approvals A. Appliance Certi fi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. BTU Speci fi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . ...

  • Heatiator ADI60S - page 4

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 4 Note : T o assure top performance, safety and ef fi ciency , inserts must be installed with an approved fl ue liner as per CAN/CGA B-149 or National Fuel Gas Code ANSI Z223 and these instructions. Not e: This installation must c onform wi th local c odes. In the absenc e of local c odes you mus ...

  • Heatiator ADI60S - page 5

    5 Heatilator • ADI60S • 345-900 Rev . G • 9/08 Heatilator gas inserts are designed for recessed installa- tions into solid fuel masonry or factory built non-combustible fi replaces that have been installed in accordance with the National, Provincial, State and local building codes. Prior to installing the gas insert: • Have the chimney and ...

  • Heatiator ADI60S - page 6

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 6 T OP VIEW A C B 3 3 F ireplace Si ze R equirement s Figure 3.1 Fireplace Opening NOTE: For actual appliance dimensions refer to Sec tion 15. Minimum Appliance Size Location ADI60 Inches Millimeters A Front Width 29-1/4 743 B Rear Width 20-1/4 515 C Depth 13-5/8 346 * Height 20-1/4 515 * NOTE: If ...

  • Heatiator ADI60S - page 7

    7 Heatilator • ADI60S • 345-900 Rev . G • 9/08 B. Clearances Figure 3.2 Clearances to Mantels or other Combustibles above Appliance Fire Risk. • Locate and install appliance to all clearance speci fi cations in manual. Fire Risk. Odor Risk. • Clearance to combustible material under the insert is 1/4 inch (0.6 cm). • Use leveling legs t ...

  • Heatiator ADI60S - page 8

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 8 Fire Risk. Asphyxiation Risk. • T erminations MUST meet minimum clearances. • Exhaust gases are hot. • Nearby vents may draw fumes into house. A. V ent T ermination Minimum Clearances Figure 4.1 speci fi es minimum vent heights for various pitched roofs. Roof Pitch H (Min.) Ft. Flat to 6/1 ...

  • Heatiator ADI60S - page 9

    9 Heatilator • ADI60S • 345-900 Rev . G • 9/08 CAUTION ALL vent speci fi cations MUST be followed. • This product is tested and listed to these speci fi cations. • Appliance performance will suffer if speci fi cations are not followed. EXHAUST VENT PIPE TERMINA TION CAP ADAPTOR INSULA TION SEAL INLET VENT AIR PIPE Figure 5.1 C. Measuri ...

  • Heatiator ADI60S - page 10

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 10 6 6 Installation Preparation Fire Risk. A hearth or hearth extension (if present) must comply with either of the following: • The solid fuel burning fi replace manufacturer’s speci fi cation. • Local building codes required by authority having jurisdiction. • NFPA 211 Prepare the exist ...

  • Heatiator ADI60S - page 11

    11 Heatilator • ADI60S • 345-900 Rev . G • 9/08 A. V enting Components 7 7 Installing V ent Pipe and Appliance The vertical vent termination system installed on this model includes: • One length of 3-inch fl exible vent pipe for combustion air (included with vent kit). Pipe will be either a 4-foot or 30-foot section depending on which kit ...

  • Heatiator ADI60S - page 12

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 12 Figure 7.2 CUT AND BEND FLASHING AS NEEDED TO FIT CHIMNEY SEALANT ADHESIVE • T rim chimney top plate to minimize excess overhang or bend over fl ue tile (see Figure 7.2). • Place 3/8 inch bead of 300º F silicone on fl ue tile top. C. Placing, Securing and Leveling the Appliance • Instal ...

  • Heatiator ADI60S - page 13

    13 Heatilator • ADI60S • 345-900 Rev . G • 9/08 D. Installing Adaptor and T ermination Cap For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 7.2) . T o install adaptor see Figure 7.3. Roof Pitch H (Min.) Ft. Flat to 6/12.................... 1.0* Over 6/12 to 7/12 ........1.25* Over 7/12 to 8/12 ...

  • Heatiator ADI60S - page 14

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 14 • Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes. • Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve. • Check all fi ttings and connections of appliance which m ...

  • Heatiator ADI60S - page 15

    15 Heatilator • ADI60S • 345-900 Rev . G • 9/08 Fire hazard. Do NOT change the valve settings. • This valve has been preset at the factory . • Changing valve settings may result in fi re hazard or bodily injury . HIGH AL TITUDE INST ALLA TIONS U.L. Listed gas appliances are tested and approved without requiring changes for elevations fro ...

  • Heatiator ADI60S - page 16

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 16 A. Wiring the Appliance 9 9 Elect rical Infor mation Note : This appliance must be electrically wired and grounded in accordance with local codes or , in the absence of local codes, with National Electric Code ANSI/NFP A 70-latest edition or the Canadian Electric Code, CSA C221.1. ON/OFF Switch ...

  • Heatiator ADI60S - page 17

    17 Heatilator • ADI60S • 345-900 Rev . G • 9/08 B. Junction Box Installation Figure 9.2 Junction box installation JUNCTION BOX SIDEW ALL JUNCTION BOX ACCESS SCREW PROVIDED Optional Accessories Connecting the electrical junction box is required if using a blower or remote. • Plug the cord into a convenient outlet. • An electrician may inst ...

  • Heatiator ADI60S - page 18

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 18 Figure 9.4 Fan/Rheostat Wire Diagram NOTE: IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE APPLIANCE MUST BE REPLACED, IT MUST BE REPLACED WITH TYPE 105 0 C RA TED WIRE. JUNCTION BOX V ARIABLE SPEED CONTROL TEMPERA TURE SENSOR SWITCH WHT GRN BLK BLK 1 10-120 V AC BLOWER BLOWER RECEPT ACLE BLK B ...

  • Heatiator ADI60S - page 19

    19 Heatilator • ADI60S • 345-900 Rev . G • 9/08 A. Mantel Projections Figure 10.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance, not the surround. 1 0 10 Fin ishing Figure 10 .1 Clearances to Mantels or other Combustibl ...

  • Heatiator ADI60S - page 20

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 20 Figure 1 1.1 Placement of Embers 1 1 11 Appliance Setup A. Remove Shipping Materials Remove shipping materials from inside or underneath the fi rebox. B. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity . C. Accessor ...

  • Heatiator ADI60S - page 21

    21 Heatilator • ADI60S • 345-900 Rev . G • 9/08 Step 3: Install the left side refractory in the same manner (see Figure 1 1.4). Step 2: While holding the back wall in place, install the right side refractory . Bend down the small tab located on the top front edge of the fi rebox (see Figure 1 1.3). Step 1: Place the back wall refractory agai ...

  • Heatiator ADI60S - page 22

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 22 Log Set Assembly: LOGS-ADI60 F . Positioning the Logs CAUTION: Logs are fragile! Carefully remove the logs from the packaging. If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately , refer to the following instructions. 1 1 2 ...

  • Heatiator ADI60S - page 23

    23 Heatilator • ADI60S • 345-900 Rev . G • 9/08 LOG #3 (SR V340-703): Position log #3 by locating its slot over the tab on the front right of the burner . Push the right side forward against the right grate tine. LOG #4 (SR V340-704): Place log #4 across log #1 and log #2 in the grooved out areas as shown. LOG #5 (SR V340-706): Place log #5 a ...

  • Heatiator ADI60S - page 24

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 24 LOG #6 (SR V340-705): Place log #6 across log #1 and log #5. The notch in the bottom of log #6 rests in the carved out section on top of log #5 and the left end of the log sits in the horizontal carved out section of log #1. LOG #7 (SR V740-707): Small log #7 rests on the “ramp” on the backs ...

  • Heatiator ADI60S - page 25

    25 Heatilator • ADI60S • 345-900 Rev . G • 9/08 Figure 1 1.5 Glass Assembly G. Glass Assembly H. Air Shutter Setting Optimal fl ame appearance is dependent on the air shutter setting. Adjustments should be made by a qualified technician. Handle glass doors with care. • Inspect the gasket to ensure it is undamaged. • Inspect the glass for ...

  • Heatiator ADI60S - page 26

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 26 Fire Risk. Explosion Risk. Gas may build up while lighting pilot. • Remove glass assembly before lighting pilot. • Replace glass assembly after lighting pilot. A. Before Lighting Appliance This appliance has a Standing Pilot Ignition. Before operating this appliance have a qualified technici ...

  • Heatiator ADI60S - page 27

    27 Heatilator • ADI60S • 345-900 Rev . G • 9/08 B. Lighting Appliance Standing Pilot Ignition 1. T urn off all electric power to the appliance if service is to be performed. 2. Open control access panel. 3. Move switch to “OFF” position. 4. Push in gas control knob slightly and turn clock- wise to OFF”. Do not force. 5. Close control ac ...

  • Heatiator ADI60S - page 28

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 28 C. Check Pilot Flame Appearance Pilot fl ame must contact the thermocouple and thermopile for reliable appliance operation. • Pilot fl ame should be as shown in Figure 12.1. D. After Appliance is Lit Initial Break-in Procedure When you light the appliance, you may notice that it pro- duces h ...

  • Heatiator ADI60S - page 29

    29 Heatilator • ADI60S • 345-900 Rev . G • 9/08 E. Frequently Asked Questions Fire Risk. High T emperatures. Keep combustible household items away from appliance. Do NOT obstruct combustion and ventilation air . • Do NOT place combustible items on top of or in front of appliance. • Keep furniture, draperies away from appliance. Smoke and ...

  • Heatiator ADI60S - page 30

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 30 A. Standing Pilot Ignition System 1 3 13 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed service person in the diagnosis of a ...

  • Heatiator ADI60S - page 31

    31 Heatilator • ADI60S • 345-900 Rev . G • 9/08 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. Continued c. Defective valve. T urn the valve knob to the ON position. Place the ON/OFF switch in the ON position. Check the millivolt meter a the thermopile terminals. The millivolt meter should read greater than 125mV . I ...

  • Heatiator ADI60S - page 32

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 32 1 4 14 Maintaining and Ser vicing Appliance Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a quali fi ed service technician should perform an appliance checkup at the beginning of each heating season. Annual inspection by quali fi ...

  • Heatiator ADI60S - page 33

    33 Heatilator • ADI60S • 345-900 Rev . G • 9/08 Inspect Maintenance T asks Doors, Surrounds and Fronts 1. Assess condition of screen and replace as necessary . Recommend addition of screen if one is not present. 2. Inspect for scratches, dents or other damage and repair as necessary . 3. V erify no obstructions to air fl ow through the louve ...

  • Heatiator ADI60S - page 34

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 34 Figure 15.1 Appliance Dimensions 1 5 15 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. Fo r framing dimensions and clearances refer to Section 3. A C B ELECTRICAL ACCESS GAS INLET D E F G H I L N K J M O P Q R S U T MODEL DI ...

  • Heatiator ADI60S - page 35

    35 Heatilator • ADI60S • 345-900 Rev . G • 9/08 B. V ent Kits Components Direct V ent Flex Liner Kits (see Figure 15.2) LINK-DV -30B or (LINK-DV -30) : Masonry 3 inch fl ex liner kit. Expands to 30 feet. Includes: two liners, termination cap, fl ashing, and link adapter . LINK-DV4-30B or (LINK-DV4-30) : Masonry 3 inch fl ex liner kit. Expa ...

  • Heatiator ADI60S - page 36

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 36 C. Service Parts Service Parts Diagram ADI60S Beginning Manufacturing Date: 8-07 Ending Manufacturing Date: ______ Part number list on following page. Log Set Assembly 1 2 3 4 5 6 7 8 9 14 13 12 11 10 19 18 17 16 15 20 21 ...

  • Heatiator ADI60S - page 37

    37 Heatilator • ADI60S • 345-900 Rev . G • 9/08 Service Parts Service Parts Diagram ADI60S IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DE ...

  • Heatiator ADI60S - page 38

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 38 Service Parts Service Parts Diagram ADI60S Beginning Manufacturing Date: July 2007 Ending Manufacturing Date: ______ IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this ...

  • Heatiator ADI60S - page 39

    39 Heatilator • ADI60S • 345-900 Rev . G • 9/08 D. Limited Lifetime W arranty Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the Unit ...

  • Heatiator ADI60S - page 40

    Heatilator • ADI60S • 345-900 Rev . G • 9/08 40 D. Limited Lifetime W arranty (continued) • This limited warranty does not extend to or include surface fi nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, fi rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosio ...

  • Heatiator ADI60S - page 41

    41 Heatilator • ADI60S • 345-900 Rev . G • 9/08 E. Contact Information - NOTES - ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ____________________ ...

Manufacturer Heatiator Category Indoor Fireplace

Documents that we receive from a manufacturer of a Heatiator ADI60S can be divided into several groups. They are, among others:
- Heatiator technical drawings
- ADI60S manuals
- Heatiator product data sheets
- information booklets
- or energy labels Heatiator ADI60S
All of them are important, but the most important information from the point of view of use of the device are in the user manual Heatiator ADI60S.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Heatiator ADI60S, service manual, brief instructions and user manuals Heatiator ADI60S. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Heatiator ADI60S.

Similar manuals

A complete manual for the device Heatiator ADI60S, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Heatiator ADI60S by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Heatiator ADI60S.

A complete Heatiator manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Heatiator ADI60S - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Heatiator ADI60S, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Heatiator ADI60S, that we can find in the current document
3. Tips how to use the basic functions of the device Heatiator ADI60S - which should help us in our first steps of using Heatiator ADI60S
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Heatiator ADI60S
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Heatiator ADI60S in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Heatiator ADI60S?

Use the form below

If you did not solve your problem by using a manual Heatiator ADI60S, ask a question using the form below. If a user had a similar problem with Heatiator ADI60S it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)