Manual Transition Networks S4TEF10xx-11x

15 pages 0.52 mb
Download

Go to site of 15

Summary
  • Transition Networks S4TEF10xx-11x - page 1

    User’ s Guide S4TEF10xx-11x Stand-Alone Media Converter • Twisted-Pair Copper to Fiber • 10/100Base-TX to 100Base-FX • RS-232 to Fiber • (4) T1/E1 to Fiber The S4TEF10xx-11x media converter is designed to extend signals from a 10Base-T Ethernet/100Base-TX Fast Ethernet port, an RS-232 data port, and up to four (4) T1/E1 network ports over ...

  • Transition Networks S4TEF10xx-11x - page 2

    2 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 PWR LKF 100Base-FX 10/100Base-TX TX RX RS-232 4 3 2 1 LNK LNK LNK LNK AIS AIS AIS AIS fiber port Ethernet port RS-232 port T1/E1 ports Part Number Fiber-Optic - Single Fiber, Single Mode, 100Base-FX S4TEF1029-110 SC, 1310 mn TX/1550 nm RX, 20 km (12.4 miles)* ...

  • Transition Networks S4TEF10xx-11x - page 3

    4 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Installation -- C ontinued Switch set #1 - T1/E1 options 5, 6, 7, 8 - Loop-Back settings The loop-back setting is used for installation and network debugging procedures. Each of the T1/E1 ports can be individually set for loop-back mode: • Switch 5 controls ...

  • Transition Networks S4TEF10xx-11x - page 4

    6 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Installation — C ontinued Switch set #2 - serial and ethernet options 6 - Twisted-pair Auto-Negotiation Up (Enabled) - The media converter “advertises” ALL rate and mode capabilities to the network: • 100 Mb/s full- or half-duplex • 10 Mb/s full- or ...

  • Transition Networks S4TEF10xx-11x - page 5

    8 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Installation — C ontinued Hardw are/softwar e jumper The jumper is located on the circuit board, inside the media converter housing. Hardware: The media converter mode is determined by the switch setting (see pages 3 - 7) . Software: The media converter mod ...

  • Transition Networks S4TEF10xx-11x - page 6

    10 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Installation -- C ontinued Install the RS-232 data cable (included) 1. Use the enclosed RS-232 data cable with a male, DIN 6-pin connector on one end and a DB-9 connector installed on the other end. 2. Connect the DIN 6-pin connector to the RS-232 port on th ...

  • Transition Networks S4TEF10xx-11x - page 7

    13 techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. Oper ation -- C ontinued Accessing the local RS232 factor y maintenance interface 1. Make sure that this Device is configured for accessing the maintenance interface via the RS232 port (Switch #10, on Bank #1, down. See page 4). 2. Attach RS232 cable from the ...

  • Transition Networks S4TEF10xx-11x - page 8

    14 SBFTF10xx-10x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Oper ation -- C ontinued Setting the password: 1. At the prompt, press the letter “P” key. 2. At the prompt, type any alphanumeric combination (8 characters maximum) 3. Press the ENTER key: the password is set. Important: After setting up or changing com ...

  • Transition Networks S4TEF10xx-11x - page 9

    16 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Oper ation -- C ontinued To show the configuration menu for the remote device: 1. At the prompt, type the letter “C,” press the spacebar, then type the letter “R.” 2. Press the ENTER key and the remote device configuration menu will appear: Note: In ...

  • Transition Networks S4TEF10xx-11x - page 10

    18 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Oper ation -- continued To Reset the local device: Caution: This command will interrupt T1/E1 and Ethernet traffic. It will take several seconds to restore the data path. Failure to observe this caution might cause data loss. 1. At the prompt, type the lette ...

  • Transition Networks S4TEF10xx-11x - page 11

    20 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 C able Specifications -- C ontinued The fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-825/CDRH standards and complies with 21 CFR1040.10 and 21 CFR1040.11. Ethernet cable Category 3: (minimum requirement for 10 Mb/s o ...

  • Transition Networks S4TEF10xx-11x - page 12

    22 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 C able Specifications —C ontinued RS-232 cable (included with the media converter) Connectors Gauge: 6-pin DIN and DB-9 / 24-22 AWG Attenuation: 20 dB/1000 ft. @ 10 MHz Differential characteristic impedance: 100 ohm +/- 10% @ 10 MHz Maximum cable distance: ...

  • Transition Networks S4TEF10xx-11x - page 13

    24 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 T r oubleshooting If the media converter fails, isolate and correct the failure by determining the answers to the following questions and then taking the indicated action: 1. Is the “PWR” LED illuminated? NO • Ensure that the power adapter is the prope ...

  • Transition Networks S4TEF10xx-11x - page 14

    26 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Contact Us Technical support Technical support is available 24 hours a day. US and Canada: 1-800-260-1312 International: 00-1-952-941-7600 Transition now Chat live via the Web with Transition Networks Technical Support. Log onto www.transition.com and click ...

  • Transition Networks S4TEF10xx-11x - page 15

    28 Trademark notice All trademarks and registered trademarks are the property of their respective owners. Copyright restrictions © 2005 Transition Networks. All rights reserved. No part of this work may be reproduced or used in any form or by any means - graphic, electronic, or mechanical - without written permission from Transition Networks. S4TE ...

Manufacturer Transition Networks Category Network Card

Documents that we receive from a manufacturer of a Transition Networks S4TEF10xx-11x can be divided into several groups. They are, among others:
- Transition Networks technical drawings
- S4TEF10xx-11x manuals
- Transition Networks product data sheets
- information booklets
- or energy labels Transition Networks S4TEF10xx-11x
All of them are important, but the most important information from the point of view of use of the device are in the user manual Transition Networks S4TEF10xx-11x.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Transition Networks S4TEF10xx-11x, service manual, brief instructions and user manuals Transition Networks S4TEF10xx-11x. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Transition Networks S4TEF10xx-11x.

A complete manual for the device Transition Networks S4TEF10xx-11x, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Transition Networks S4TEF10xx-11x by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Transition Networks S4TEF10xx-11x.

A complete Transition Networks manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Transition Networks S4TEF10xx-11x - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Transition Networks S4TEF10xx-11x, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Transition Networks S4TEF10xx-11x, that we can find in the current document
3. Tips how to use the basic functions of the device Transition Networks S4TEF10xx-11x - which should help us in our first steps of using Transition Networks S4TEF10xx-11x
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Transition Networks S4TEF10xx-11x
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Transition Networks S4TEF10xx-11x in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Transition Networks S4TEF10xx-11x?

Use the form below

If you did not solve your problem by using a manual Transition Networks S4TEF10xx-11x, ask a question using the form below. If a user had a similar problem with Transition Networks S4TEF10xx-11x it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)