-
Toshiba KV-7168A - page 1
INTRODUCTION 4 PREPARATION 11 RECORDING OPERATION 23 PLAYBACK OPERATION 39 NOTICE 44 Instruction Manual VIRTUAL REAL-TIME & TIME LAPSE VCR KV-7168A POWER TAPE REMAIN TIME LAPSE VCR 4Head 168Hour DISPLAY PLAY STOP REV FWD TIME MODE SET SHIFT TRACKING LOCATION SELECT COUNTER ALARM RESET MEMORY + – PAUSE/STILL ...
-
Toshiba KV-7168A - page 2
Only cassettes marked can be used with this VCR. This VCR is not compatible with ordinary VCRs. PLEASE READ The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magni- tude to constitu ...
-
Toshiba KV-7168A - page 3
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE 2 CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE. This set has been designed and manufactured to assure personal safety. Improper use can result in electric shoc ...
-
Toshiba KV-7168A - page 4
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION 3 10. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, AN ...
-
Toshiba KV-7168A - page 5
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE I NTRODUCTION FEA TURES Restart record function. This function enables the VCR to automatically restart the record- ing process in the event of a power failure. After power is restored, the VCR will restart the recording process. (See page 24.) Shuttle function. With the shuttle ...
-
Toshiba KV-7168A - page 6
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION INSTRUCTIONS IN BRIEF Front Panel 5 + ...
-
Toshiba KV-7168A - page 7
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE 6 TAPE REMAIN button The approximate time remaining on the tape is displayed on the counter (in a 2 hour scale using a T-120 tape) while this button is being pressed. CASSETTE COMPARTMENT Insert a cassette into this compartment to load the tape. DISPLAY button Press to display t ...
-
Toshiba KV-7168A - page 8
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION VIDEO OUT connector (BNC) Output connector for video signal. Connect with a monitor TV. AUDIO IN jack (RCA type) Input jack for audio signal. Connect with an external audio source. AUDIO OUT jack (RCA type) Output jack for audio signal. Connect with an external audio equipment. ...
-
Toshiba KV-7168A - page 9
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE A Word on the Exclusive 3N-100AAS Battery Pack The nickel-cadmium battery pack (3N-100AAS) is used for power source of the built-in clock and memory circuit. Charging the Battery Pack 1. Turn on the power of the VCR. 2. The battery pack in the VCR is charged. Battery Installatio ...
-
Toshiba KV-7168A - page 10
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION PLAY R E C ALARM COUNT. M ALARM M PW.FAIL DEW TIMER H SP EP VCR DISPLA Y 10 Cassette indicator Lights when a tape is inserted. Counter memory indicator Lights when the counter memory is selected. Alarm Memory indicator Lights when the alarm memory is selected. Alarm indicator Li ...
-
Toshiba KV-7168A - page 11
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE PLAY (–) PLAY TIME (+) STOP REW FF STILL PAUSE/ PICTURE SEARCH WIRED REMOTE CONTROL (Option) 10 PAUSE/STILL button • Press during recording to pause the recording. • Press during playback to play back a still picture. REW button • Press to rewind the tape. • Press duri ...
-
Toshiba KV-7168A - page 12
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION CONNECTIONS Connection with a Video Camera P REPARATION 11 ALL CLEAR REMOTE IN MIC IN IN GND RESET OUT GND OUT GND TAPE END ALARM REC TRIGG. IN OUT VIDEO IN OUT AUDIO SEE MANUAL SEE MANUAL Monitor TV To AC OUTLET (120V) To AC OUTLET (120V) QUAD ONLY SWITCHED OFF LOOP THROUGH IN ...
-
Toshiba KV-7168A - page 13
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE VIDEO IN VIDEO OUT 12345 CAMERA ALARM IN REMOTE 678 12345 678 ALARM OUT MONITOR VCR REC VCR PLAY Monitor TV. AC120V To AC outlet To ALARM IN To VCR playback Frame Sequential Switcher To VCR REC To ALARM OUTPUT To VIDEO OUT To GND To REC TRIGGER INPUT To REC TRIGG. OUT To VIDEO I ...
-
Toshiba KV-7168A - page 14
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION The normal MENU screen provides six menus after the initial screen for clock setting. Each MENU screen is shown below. Press the DISPLAY button for a MENU screen. The menu is selected by pressing the SHIFT button. Then press the SET button to proceed to the next screen. Use the ...
-
Toshiba KV-7168A - page 15
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE PROGRAM Screen Setting of timer recording. ALARM RECALL Screen TIME DATE SEARCH Screen Alarm recall display Set the day and time to be searched and searching direction. 14 M E N U CLOCK ADJUST SETUP SETUP DISPLAY MODE END=[DISPLAY] PROGRAM ALARM RECALL TIME DATE SEARCH TH2 ON -- ...
-
Toshiba KV-7168A - page 16
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION DISPLAY TIME MODE SET SHIFT TRACKING LOCATION SELECT + – DISPLAY TIME MODE SET SHIFT TRACKING LOCATION SELECT + – An internal clock generates time and date for superimposing on the monitor screen. Adjust the time from the MENU screen (initial screen). After the clock is set, ...
-
Toshiba KV-7168A - page 17
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE ON-SCREEN FUNCTIONS When the power is turned ON, the time and date modes are displayed on the monitor screen (live picture). On-screen displays are not available in the event of no video input signal. Date-Time Display VCR display Monitor screen Date : Displayed with the month-d ...
-
Toshiba KV-7168A - page 18
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION 17:30:02 A 2 8/28/96 WED 17:30:02 A 2 8/28/96 WED 17:30:02 A 2 8/28/96 WED 17:30:02 A 2 8/28/96 WED DISPLAY TIME MODE SET SHIFT TRACKING LOCATION SELECT + – DISPLAY TIME MODE SET SHIFT TRACKING LOCATION SELECT + – DISPLA Y SCREEN Set the MENU screen to DISPLAY screen, and se ...
-
Toshiba KV-7168A - page 19
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE DISPLAY TIME MODE SET SHIFT TRACKING LOCATION SELECT + – Note: Press the DISPLAY button twice to return from the display screen to the monitor screen. Changes as shown below each time the SET button is pressed. OFF → V01 → V02 → V03 → V04 → V05 → V06 → V07 → V0 ...
-
Toshiba KV-7168A - page 20
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION 2 Press the RESET button at the location you want to see. COUNTER DISPLA YS Counter Memory When the counter is set to “0000” at a location that you want to see again during recording and playback, the tape will stop in the vicinity of “0000” during rewind and fast forwar ...
-
Toshiba KV-7168A - page 21
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE 20 Notes: In the cases shown below, Alarm Memory search may be not carried out. If the alarm recording is not carried out for more than those listed in the following chart then, the alarm may be skipped. If the alarm recording interval is not left for more than those listed in t ...
-
Toshiba KV-7168A - page 22
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION SP A 2 2 H 2 H 40 M 1/60s 60.0 fields/s Possible Continuous EP A 6 6 H 8 H 1/60s 60.0 fields/s Possible Continuous SP A12 14 H 18 H 40 M 0.12s 8.57 fields/s Possible Continuous EP A18 18 H 24 H 1/20s 20.0 fields/s Possible Continuous (Virtual Real Time mode) SP A24 26 H 34 H 40 ...
-
Toshiba KV-7168A - page 23
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE TIMER POWER EJECT VIDEO MODE TAPE REMAIN TIME LAPSE VCR 4Head 168Hour DISPLAY PLAY TIME MODE SET SHIFT TRACKING LOCATION SELECT COUNTER ALARM RESET MEMORY AUTO B/W COLOR REMOTE OFF REMOTE OPTION BUZZER ON OFF REC REC CHECK + – P EJECT LO ADING AND UNLO ADING A VIDEO CASSETTE L ...
-
Toshiba KV-7168A - page 24
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION RECORDING 1 Turn on the power for this VCR as well as associated devices of the surveillance system including the video camera and monitor TV. 5 Insert a video cassette to this VCR. • Check that the safety tab on the video cassette has not been removed. 2 Adjust the monitor TV ...
-
Toshiba KV-7168A - page 25
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE REST AR T RECORDING Setting the Restart Recording On the SETUP screen set RESTART REC to ON. 24 Note: When a power failure occurs (10 days or less in duration) during recording or timer recording, the VCR resumes automatically to the same mode when the power is restored regardle ...
-
Toshiba KV-7168A - page 26
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION TIMER RECORDING There are two kinds of timer recording. One is daily timer recording, and the other is weekly timer recording. Once the timer programs are set, the VCR can retain all programmed information in the event of a power failure (10 day maximum memory storage). Before s ...
-
Toshiba KV-7168A - page 27
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE 7 Press the SHIFT button to blink end time. Set end time to 17:00 with the SET button and the SHIFT button in the same manner as 6. 9 Press the DISPLAY button twice to erase the MENU screen. 10 Press the TIMER button. 8 Press the SHIFT button and the + SET button to set recordin ...
-
Toshiba KV-7168A - page 28
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION Weekly Timer Recording To record every week for certain period on a certain day of the week, set the weekly timer recording. With the weekly timer recording, 2 programs are possible for each day of the week. In case of setting A18 from 8:00 to 19:00 on all weekdays, and A18 from ...
-
Toshiba KV-7168A - page 29
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE 9 Press the + SET button to set to A18. 11 Set to WE1 and TH1 following the steps from 4 to 10. 10 Press the SHIFT button twice to blink the TU1 start time. Repeat steps from 5 to 9. Overlapping Programs 12 When TH2 ending minute blinks, press the SHIFT button. The screen change ...
-
Toshiba KV-7168A - page 30
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION If an alarm condition arises, the alarm function operates with an alarm input signal. ALARM RECORDING 29 Operation at Alarm Input When there is an alarm during recording, recording pause or stop modes, the VCR automatically goes into alarm recording mode. The VCR can be programm ...
-
Toshiba KV-7168A - page 31
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE Connecting the Alarm Terminals Connecting the ALARM IN/OUT terminals • When the alarm switch is ON, alarm recording starts. It is possible to confirm the warning from outside by connecting the switching input of external interface devices such as alarm lamp or alarm buzzer to ...
-
Toshiba KV-7168A - page 32
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION Each time the + SET button is pressed, the display changes as follows. → STOP → CONT. STOP ... Stops at tape end when any alarm condition has occurred. CONT .. Performs an operation selected by TAPE END MODE on MENU SCREEN when tape end is detected. Setting the Alarm Recordi ...
-
Toshiba KV-7168A - page 33
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE 32 ONE-SHOT RECORDING It is possible with this VCR to carry out one-shot recording to record only when there is a trigger input from outside or for use as a data file. If a trigger is input to the one-shot input on the back, there will be recording for the field numbers set at t ...
-
Toshiba KV-7168A - page 34
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION 33 DISPLAY TIME MODE SET SHIFT TRACKING LOCATION SELECT + – DISPLAY TIME MODE SET SHIFT TRACKING LOCATION SELECT + – 5 Press the SHIFT button to make INTERVAL blink. Press the + SET button to set the time interval be- tween the individual recording fields. 6 Press the DISPLA ...
-
Toshiba KV-7168A - page 35
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE OPERA TION AFTER T APE END DETECTION The VCR can be programmed to respond differently when the tape reaches its end. The following describes how to set the different modes of operation. 34 How to Set to Stop at End of Tape 1 Press the DISPLAY button. 2 Press the or SHIFT button ...
-
Toshiba KV-7168A - page 36
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION The VCR can be programmed to automatically rewind the tape when the tape reaches its end. How to Set to Auto Rewind at End of Tape 35 1 Press the DISPLAY button. Note: Alarm recording does not operate during auto-rewind. 2 Press the or SHIFT button to blink SETUP and press the + ...
-
Toshiba KV-7168A - page 37
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE The VCR can be programmed to automatically restart recording when the tape reaches its end. With this function, the VCR will automatically rewind the tape and begin recording. 36 How to Set to Repeat Record at End of Tape 1 Press the DISPLAY button. 2 Press the or SHIFT button t ...
-
Toshiba KV-7168A - page 38
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION RECORDING WITH THE SEQUENTIAL SWITCHER This VCR can work with a sequential switcher connected for recording. Connection with the Sequential Switcher For detailed operations and connections of the switcher, consult the Instruction Manual of the sequential switcher. Timing for Cam ...
-
Toshiba KV-7168A - page 39
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE REC Trigger Output Selection in the Alarm Recording REC Trigger output can be selected during the alarm recording. 1 Press the DISPLAY button. 2 Press the SHIFT button to blink SETUP. 3 Press the + SET button. 4 Press the SHIFT button. And press the + SET button to set the REC t ...
-
Toshiba KV-7168A - page 40
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION 39 1 Turn the power ON for the monitor TV. PLA YB A CK 2 Insert a tape which has been recorded on. 3 Press the PLAY button. 4 Select the playback time mode. Tracking Adjustment Use the , TRACKING button to adjust when noise appears on the playback screen. 123 The picture may be ...
-
Toshiba KV-7168A - page 41
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE 40 If you release the dial, it turns to the center position. Notes: • As the SHUTTLE dial is turned in the stop mode, the VCR is set to the FF or REW mode and it does not go back to stop mode until you press the STOP button. Turning the dial back to initial position does not r ...
-
Toshiba KV-7168A - page 42
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION PLA YB A CK IN V ARIOUS MODES The following operations are possible during playback. Picture Search It is possible to carry out fast forward and rewind while viewing picture and thus quickly locate the section you wish to view (image played back at speed of 5 times faster than A ...
-
Toshiba KV-7168A - page 43
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE TIME D A TE SEARCH Searching a picture at a desired day and time is possible by specifying the day and hour on the MENU screen. The VCR automatically records the current date and time (day/hour/minute). Accordingly, make sure before recording that the date and time is exactly ad ...
-
Toshiba KV-7168A - page 44
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION ALARM SEARCH With the alarm search function, it is possible to search for alarm that has been recorded on the tape. Search Operation 1 Press the STOP button. 2 Press the COUNTER MEMORY button twice to make “ALARM M” to light. 3 Turn the SHUTTLE dial to set rewind or fast for ...
-
Toshiba KV-7168A - page 45
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE Additional remarks Input/Output Terminal Signal level SIGNAL LEVELS OF INPUT/OUTPUT TERMINALS N OTICE 44 ALARM IN ALARM RESET ALARM OUT REC TRIGG. OUT TAPE END OUT ONE SHOT IN ...
-
Toshiba KV-7168A - page 46
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION Order of Daily Checks 1 Turn the power ON for this VCR and for the connected devices in the surveillance system including the video camera and monitor TV. 6 Press the PLAY button. 2 Does the correct picture appear in the monitor TV? 3 Is the date-time display correct on the moni ...
-
Toshiba KV-7168A - page 47
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE Steps to Take after Daily Checks If an abnormality is found, turn the power switch to OFF and remove the power plug from the household AC outlet. Then consult with your dealer. Tape Usage Frequency Replace tapes using the table below as a guide. A Request for Periodic Checks Thi ...
-
Toshiba KV-7168A - page 48
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION Dew Condensation CAUTIONS DURING USE This VCR includes a safety function to prevent operation when dew condensation occurs and thus protects against damage to tapes, the video heads and other parts. What is condensation? If you pour cold beer in a glass, water droplets gather on ...
-
Toshiba KV-7168A - page 49
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE Installation Power does not go ON. There is no camera picture. The camera picture is indistinct. Function/Operation The VCR does not operate even when the control buttons are pressed. The clock does not run after restoration of power following a power failure. The buzzer does no ...
-
Toshiba KV-7168A - page 50
NOTICE PREPARATION INTRODUCTION RECORDING OPERATION PLAYBACK OPERATION Playback Adjust with the TRACKING button. The video head may be clogged or worn out. Consult with your dealer. Press the TRACKING button in a still playback mode and adjust. Are you using an external synchronous or gen-lock synchronous video camera? Consult with your dealer. Is ...
-
Toshiba KV-7168A - page 51
RECORDING OPERATION PREPARATION INTRODUCTION PLAYBACK OPERATION NOTICE SPECIFICA TIONS Power supply 120V AC, 60 Hz Power consumption 18W External dimensions 17 × 3-5/8 × 12-1/2 inch (W × H × D), 430 × 92 × 318 mm (W × H × D) Weight 11 lbs (5.0 kg) Signal system Standard NTSC color television system Recording System Rotary 2-head azimuth Cas ...
-
Toshiba KV-7168A - page 52
CCTV GROUP VIDEO COMMUNICATION & INFORMATION SYSTEM DIVISION 1010 Johnson Drive Buffalo Grove, Illinois 60089-6900 (708)541-9400 Printed in Japan 70971646 TOSHIBA AMERICA C.P.INC. ...
Do you have a question concerning Toshiba KV-7168A?
Use the form below
If you did not solve your problem by using a manual Toshiba KV-7168A, ask a question using the form below. If a user had a similar problem with Toshiba KV-7168A it is likely that he will want to share the way to solve it.