English dropdown-ico

Manual Axis Communications Q6042

32 pages 3.11 mb
Download

Go to site of 32

Summary
  • Axis Communications Q6042 - page 1

    AXIS Q604 Series AXIS Q6042 PTZ Dome Network Camera AXIS Q6044 PTZ Dome Network Camera AXIS Q6045 PTZ Dome Network Camera E N G L I SH Installation Guide ...

  • Axis Communications Q6042 - page 2

    Legal Considerations Video and audio surveillance can be regulated by laws that vary from country to country . Check the laws in your local region before using this product for surveillance purposes. This product includes one (1) H.264 decoder license and one (1) AAC decoder license. To purchase further licenses, contact your reseller . Liability E ...

  • Axis Communications Q6042 - page 3

    Australia/New Zealand This digital equipment fullls the requirements for RF emission according to the Class A limit of AS/NZS CISPR 22. The product shall be connected using a shielded network cable (STP) that is properly grounded. Notice! This is a Class A product. In a domestic environment this product may cause RF interference, in which case t ...

  • Axis Communications Q6042 - page 4

    ...

  • Axis Communications Q6042 - page 5

    AXIS Q604 Series Safety Infor mation Read through this Installation Guide carefully before installing the product. Keep the Installation Guide for future reference. Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury . WARNING Indicates a hazardous situation which, if not avoided, could ...

  • Axis Communications Q6042 - page 6

    AXIS Q604 Series Safety Instructions WARNING • The Axis product shall be installed by a trained professional. NO NO NO TICE TICE TICE • The Axis product shall be used in compliance with local laws and regulations. • To use the Axis product outdoors, or in similar environments, it shall be installed in an approved outdoor housing. • Store th ...

  • Axis Communications Q6042 - page 7

    AXIS Q604 Series WARNING • Risk of explosion if the battery is incorrectly replaced. • Replace only with an identical battery or a battery which is recommended by Axis. • Dispose of used batteries according to local regulations or the battery manufacturer's instructions. Dome Cover NO NO NO TICE TICE TICE • Be careful not to scratch, d ...

  • Axis Communications Q6042 - page 8

    8 ...

  • Axis Communications Q6042 - page 9

    AXIS Q604 Series Installation Guide This Installation Guide provides instructions for installing AXIS Q6042/Q6044/Q6045 Mk II PTZ Dome Network Camera on your network. For other aspects of using the product, see the User Manual available at www .axis.com Installation Steps 1. Make sure the package contents, tools and other materials necessary for th ...

  • Axis Communications Q6042 - page 10

    AXIS Q604 Series Hardware Overview 1 2 4 5 6 7 8 9 10 3 1 Unit holder (3x) 2 Camera base lid 3 Camera base lid screw T20 (3x) 4 Hook for safety wire 5 P art number (P/N) & Serial number (S/N) 6 Cable track (2x) 7 Foam gasket 8 Network connector (P oE+) 9 Multi-connector 1 0 Top cover 1 0 ...

  • Axis Communications Q6042 - page 11

    AXIS Q604 Series Camera Unit 1 2 3 4 1 SD card slot (SDHC) 2 Status LED indicator 3 Control button 4 P ower button Dome Cover 1 2 3 4 5 1 Dome bracket screw T20 (4x) 2 Dome bracket 3 Dome cover 4 Dome ring screw T20 (4x) 5 Dome ring 1 1 E N G L I SH ...

  • Axis Communications Q6042 - page 12

    AXIS Q604 Series Hard Ceiling Mount 1 2 1 Mounting plate 2 Safety wire Drop Ceiling Mount 1 2 3 4 5 6 7 1 Mounting plate 2 Mounting plate screw T20 (3x) 3 Bracket arm 4 Bracket arm screw T20 (3x) and washer (3x) 5 Bracket ring 6 Trim ring 7 Safety wire 12 ...

  • Axis Communications Q6042 - page 13

    AXIS Q604 Series LED Indicators LED Color Indication Unlit Connection and normal operation Amber Steady during startup. Flashes during rmware upgrade. Amber/red Flashes amber/red if network connection is unavailable or lost. Red Flashes red for rmware upgrade failure. Status Green Shows steady green for 1 0 seconds for normal operation after ...

  • Axis Communications Q6042 - page 14

    AXIS Q604 Series NO NO NO TICE TICE TICE The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network shall be intended for their specic use. Make sure that the network devices are installed in accordance with the manufacturer’s instructions. For information about regulatory requirements ...

  • Axis Communications Q6042 - page 15

    AXIS Q604 Series Multi-Connector Cable (sold separately) When connecting external equipment to the Axis product, a multi-connector cable (available from Axis) is required in order to maintain the product’s IP rating. The multi-connector cable can be purchased from your Axis reseller . Connect the multi-connector cable to the product’s multi-con ...

  • Axis Communications Q6042 - page 16

    AXIS Q604 Series Digital input – Connect to pin 1 to activate, or leave oating (unconnected) to deactivate. 0 to max 40 V DC Congurable (Input or Output) 3–6 Digital output – Connected to pin 1 when activated, oating (unconnected) when deactivated. If used with an inductive load, e.g. a relay , a diode must be connected in parallel w ...

  • Axis Communications Q6042 - page 17

    AXIS Q604 Series I/O connector 1 2 3 4 5 6 DC power input AC power input Specications Operating Conditions The Axis product is intended for indoor use. Product Classication Temperature Humidity AXIS Q6042 AXIS Q6044 AXIS Q6045 IEC 60 721-4-3 Class 3K3, 3M3 IEC 60529 IP52 0 °C to 50 °C (32 °F to 122 °F) 1 0–85% RH (non-condensing) P ower ...

  • Axis Communications Q6042 - page 18

    AXIS Q604 Series Connectors SD Card Slot Supports SD cards with up to 64 GB of storage. For best recording performance, use an SDHC or SDXC card with speed class 1 0. Install the Hardware NO NO NO TICE TICE TICE • The AXIS product shall be connected using a shielded network cable (STP). All cables connecting the product to the midspan shall be sh ...

  • Axis Communications Q6042 - page 19

    AXIS Q604 Series 2. Remove the dome bracket screws and remove the dome bracket and the dome cover from the dome ring. 3. Attach the dome bracket and the dome cover to the dome ring and tighten the screws (torque 1.2 Nm). 4. To install an SD card (not included), see Install an SD Card on page 19 . 5. Attach the dome cover to the top cover and tighte ...

  • Axis Communications Q6042 - page 20

    AXIS Q604 Series 5. Route and connect the network cable and the multi-connector cable (sold separately), if applicable, to the camera. NO NO NO TICE TICE TICE • Be careful not to damage the cables when connecting them. • Make sure that the foam gasket holes are aligned with the cable tracks and, if applicable, remove the cut-out piece for the m ...

  • Axis Communications Q6042 - page 21

    AXIS Q604 Series 1 2 1 Ceiling tile 2 Hole diameter 225 mm (8.9 in.) 3. Assemble the ceiling bracket and attach it to the ceiling tile. Make sure the arrows on the mounting plate and the ceiling bracket are pointing in the same direction for the logotypes on the camera and the trim ring to align. 4. Tighten the bracket arm screws. 5. Loosen the cam ...

  • Axis Communications Q6042 - page 22

    AXIS Q604 Series 2 1 3 4 5 1 Mounting plate 2 Ceiling bracket 3 Ceiling tile 4 Safety wire 5 Hook for safety wire 1 0. Slide the unit holders on the network camera into the slots in the mounting plate and rotate the camera unit. 1 1. Install the supplied midspan. See page 25 . 12. Install the ceiling tile with the camera mounted on it. 13. Put the ...

  • Axis Communications Q6042 - page 23

    AXIS Q604 Series 1 2 1 Trim ring 2 Trim ring screw T20 (4x) Bracket Mount (sold separately) 1. Install the selected bracket according to the instructions supplied with the bracket. If drilling is required, make sure to use drill bits, screws and plugs that are appropriate for the material. 2. Loosen the camera base lid screws and remove the camera ...

  • Axis Communications Q6042 - page 24

    AXIS Q604 Series 1 2 3 4 1 Screw T30 (3x) 2 Slot for unit holder (3x) 3 Safety wire 4 Wall bracket (mounting example) 5. Connect the network cable and the multi-connector cable (sold separately), if applicable, to the camera. NO NO NO TICE TICE TICE • Be careful not to damage the cables when connecting them. • Make sure that the foam gasket hol ...

  • Axis Communications Q6042 - page 25

    AXIS Q604 Series 6. Turn the cable holders to keep the cables in place. 7. Put the camera base lid back in its original position and tighten the screws (torque 1.5 Nm). 8. Slide the unit holders on the network camera into the slots in the mounting bracket and rotate the camera unit. 9. Secure the network camera to the mounting bracket by tightening ...

  • Axis Communications Q6042 - page 26

    AXIS Q604 Series Access the Product Use the tools provided on the Installation and Management Software CD to assign an IP address, set the password and access the video stream. This information is also available from the support pages on www .axis.com/techsup/ Reset to Factory Default Settings Important Reset to factory default should be used with ...

  • Axis Communications Q6042 - page 27

    AXIS Q604 Series Warranty Information For information about Axis’ product warranty and thereto related information, see www .axis.com/warranty/ 27 E N G L I SH ...

  • Axis Communications Q6042 - page 28

    ...

  • Axis Communications Q6042 - page 29

    Regulatory I nformation USA This equipment has been tested using an unshielded network cable (UTP) and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. This equipment has also been tested using a shielded network cable (STP) and found to comply with the limits for a Class A digital device, pursuant ...

  • Axis Communications Q6042 - page 30

    ...

  • Axis Communications Q6042 - page 31

    ...

  • Axis Communications Q6042 - page 32

    Installation Guide V er . M2.8 AXIS Q604 Series Date: August 20 14 © Axis Communications AB, 2014 P art No. 59 146 ...

Manufacturer Axis Communications Category Security Camera

Documents that we receive from a manufacturer of a Axis Communications Q6042 can be divided into several groups. They are, among others:
- Axis Communications technical drawings
- Q6042 manuals
- Axis Communications product data sheets
- information booklets
- or energy labels Axis Communications Q6042
All of them are important, but the most important information from the point of view of use of the device are in the user manual Axis Communications Q6042.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Axis Communications Q6042, service manual, brief instructions and user manuals Axis Communications Q6042. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Axis Communications Q6042.

Similar manuals

A complete manual for the device Axis Communications Q6042, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Axis Communications Q6042 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Axis Communications Q6042.

A complete Axis Communications manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Axis Communications Q6042 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Axis Communications Q6042, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Axis Communications Q6042, that we can find in the current document
3. Tips how to use the basic functions of the device Axis Communications Q6042 - which should help us in our first steps of using Axis Communications Q6042
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Axis Communications Q6042
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Axis Communications Q6042 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Axis Communications Q6042?

Use the form below

If you did not solve your problem by using a manual Axis Communications Q6042, ask a question using the form below. If a user had a similar problem with Axis Communications Q6042 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)