-
Pelco C2445M-D - page 1
ADDENDUM Addendum No. C2499M-A Date November 17, 2005 Manuals Affected Spectra III ™ SE Series Dome Drive Manuals: C2443M-C, C2444M-C, and C2445M-D Manual Update The following are manual changes for Spectra III SE software V ersion 1.28 and greater and instructions for accessing a Spectra III EVS dome system. Presets Spectra III SE system presets ...
-
Pelco C2445M-D - page 2
Worldwide Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www .pelco.com USA & Canada • T el: 800/289-9100 • Fax: 800/289-9150 International • T el: 1-559/292-1981 • Fax: 1-559/348-1120 Pelco and the Pelco logo are registered trademarks of Pelco. ©Copyright 2005, Pelco. All rights reserved. Spectra III and Endura a ...
-
Pelco C2445M-D - page 3
Spectra III ™ SE Series C2443M-C (1/04) OPERA TION/PROGRAMMING ® Models DD53M22 & DD53M22-X ...
-
Pelco C2445M-D - page 4
OPERA TION/PROGRAMMING MANUAL MODELS DD53M22 & DD53M22-X 22X LowLight ™ MONOCHROME TECHNOLOGY ...
-
Pelco C2445M-D - page 5
2 C2443M-C (1/04) CONTENTS WELCOME ................................................................................................................................................................................................ 5 GETTING ST ARTED ....................................................................................................... ...
-
Pelco C2445M-D - page 6
C2443M-C (1/04) 3 <WINDOW BLANKING> .............................................................................................................. ................................................... 32 REVERSE ...................................................................................................................................... ...
-
Pelco C2445M-D - page 7
4 C2443M-C (1/04) ...
-
Pelco C2445M-D - page 8
C2443M-C (1/04) 5 WELCOME Thank you for purchasing Pelco’ s premier integrated dome system, Spectra III SE. Y our new system features a high resolution, monochrome camera with programmable dome drive software. This manual is designed to be a reference tool for the operation and programming of your system. Inside you will find information about Sp ...
-
Pelco C2445M-D - page 9
6 C2443M-C (1/04) HOW TO OPERA TE YOUR DOME SYSTEM Operation How to Control Pan and T ilt Move joystick or press the direction keys left/right and up/down. Zoom Far To zoom far , do the following: 1. Press the Zoom T ele button or turn the joystick clockwise until zoom stops at the 32X zoom limit . 2. Release the button or joystick for one second. ...
-
Pelco C2445M-D - page 10
C2443M-C (1/04) 7 Accessing Main Menu (Preset 95) Y ou can call up the main menu on your monitor by programming (setting or creating) preset 95 (preset 28 if in AD32-preset mode). Programming preset 95 for Pelco’ s controllers varies according to the type of controller you are using. Instructions for programming preset 95 are given below for vari ...
-
Pelco C2445M-D - page 11
8 C2443M-C (1/04) KBD4000/KBD4002 (GENEX ® MUL TIPLEXER) 1. Press the SPOT MONITOR key . 2. Enter 95, then hold the PRESET key (approximately five seconds) until the main menu appears on the screen. MPT9500 Standard Coaxitron Mode 1. Enter 95 and press the PRESET SET key . 2. Position the asterisk in the YES row and press the F1 key . The main men ...
-
Pelco C2445M-D - page 12
C2443M-C (1/04) 9 QUICK ST ART GUIDE – SYSTEM SETUP Presets The following presets are reserved for special functions. Preset Function 33 Flip command 90-91 Manual limit stops 92-93 Scan limit stops 95 Select main programming menu 96 Stop a scan 97 Random scanning 98 Frame scanning 99 Start auto scanning NOTE: For American Dynamics controllers wit ...
-
Pelco C2445M-D - page 13
C2443M-C (1/04) 11 LANGUAGE The language for the on-screen menus is selectable. Available languages include English, Spanish, French, German, Italian, and Portuguese. The factory default language is English. To change the display language: 1. Use the joystick to position the cursor beside LANGUAGE. 2. Press Iris Open. The cursor moves to the right, ...
-
Pelco C2445M-D - page 14
12 C2443M-C (1/04) SYSTEM INFORMA TION The system Information screen displays dome drive model, software version, available memory , and other diagnostic information. System settings cannot be changed using this screen. This screen is for reference only . Use the following steps to display the System Information screen: 1. Use the joystick to posit ...
-
Pelco C2445M-D - page 15
C2443M-C (1/04) 13 DISPLA Y SETUP Display setup allows you to program how labels are displayed on the monitor . The following labels are available: PRESET LABEL - Identifies preset. ZONE LABEL - Identifies zone. ZOOM RA TIO - Identifies the amount of magnification. AZIMUTH 1 /ELEV A TION 2 - Amount of pan from 0 ° and the amount of tilt from 0 ° ...
-
Pelco C2445M-D - page 16
14 C2443M-C (1/04) <Label Position> Labels can be placed anywhere on the monitor . This feature allows you to customize the appearance of your monitor screen. The following labels are not set at fixed positions: PRESET LABEL ZONE LABEL ALARM 1 ZOOM RA TIO - XXX.XX AZIMUTH 1 /ELEV A TION 2 - XXX ° /-XX ° DIRECTION-NE ALERT MESSAGE 3 * To set ...
-
Pelco C2445M-D - page 17
C2443M-C (1/04) 15 BACK EXIT TYPE OF LIGHTING OUTDOOR AUTO FOCUS ON ZOOM LIMIT X176 ZOOM SPEED MEDIUM LOW LIGHT LIMIT 2 <ADVANCED SETTINGS> CAMERA BACK EXIT <CAMERA> <MOTION> <POWER UP> <LINE SYNC> <PRESETS> <P A TTERNS> <ZONES> <WINDOW BLANKING> <ALARMS> <AUX> <ALERT>* <CLE ...
-
Pelco C2445M-D - page 18
16 C2443M-C (1/04) ZOOM LIMIT Zoom limit allows the user to define a limitation on the amount of telephoto zoom. The default setting is 176X. Cameras with 264X zoom (22X optical zoom and 12X electronic zoom) can be set for 22X, 32X, 88X, 176X, 220X, or 264X. ZOOM SPEED Zoom Speed allows the user to define how fast the dome will go from full wide zo ...
-
Pelco C2445M-D - page 19
C2443M-C (1/04) 17 BACK EXIT ADVANCED SETTINGS SHUTTER SPEED AUTO AGC LIMIT 27 AUTO IRIS AUTO AUTO IRIS LEVEL 66 AUTO IRIS PEAK 8 AUTO SHARPNESS ON SHARPNESS LEVEL 26 BACKLIGHT COMP OFF VIDEO LEVEL HIGH BACK EXIT TYPE OF LIGHTING OUTDOOR AUTO FOCUS ON ZOOM LIMIT X176 ZOOM SPEED MEDIUM LOW LIGHT LIMIT 2 <ADVANCED SETTINGS> CAMERA <Advanced ...
-
Pelco C2445M-D - page 20
18 C2443M-C (1/04) AUTO IRIS Auto iris is the lens function that automatically opens and closes the iris in response to changing light conditions. Program the auto iris to operate automatically or at a user -defined level. OFF - Auto iris is disabled, and control is always manual. AUTO (default) - The iris is adjusted automatically to produce a con ...
-
Pelco C2445M-D - page 21
C2443M-C (1/04) 19 AUTO SHARPNESS Auto sharpness enhances picture detail by increasing the aperture gain of the camera and sharpening the edges in the picture. There are two settings: ON (default) - The camera automatically maintains a normal sharpness mode. OFF - The sharpness of the picture is set manually by programming the SHARPNESS LEVEL. Shar ...
-
Pelco C2445M-D - page 22
20 C2443M-C (1/04) BACKLIGHT COMPENSA TION (BLC) If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette. Backlight compensation enhances objects in the center of the picture. The dome uses the center of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out ...
-
Pelco C2445M-D - page 23
C2443M-C (1/04) 21 <Motion Settings> AUTO FLIP When the camera tilts downward and goes just beyond the vertical position, the dome rotates 180 degrees. When the dome rotates (flips), the camera starts moving upward as long as you continue to hold the joystick in the down position. Once you let go of the joystick after the dome rotates, joysti ...
-
Pelco C2445M-D - page 24
22 C2443M-C (1/04) PARK TIME This feature allows the dome to begin a specified operation (scan, preset, or pattern) after a programmed time of inactivity . Park time can be programmed from 1 minute to 720 minutes (12 hours), or set to zero, which disables this feature. The default setting is zero. Park Action This feature will define the activity w ...
-
Pelco C2445M-D - page 25
C2443M-C (1/04) 23 SCAN SPEED Scan speed is the degrees per second that the dome will pan when in a scan mode. Scan speed is adjustable from 1 to 40 degrees per second through the programming menu. The default setting is 25 degrees per second. PRESET FREEZE FRAME This feature freezes the scene on the monitor when going to a preset. This allows for ...
-
Pelco C2445M-D - page 26
24 C2443M-C (1/04) LIMIT STOPS Limit stops are programmable stops that limit the pan range of the dome. There must be two limits, a left and a right, to define an area. There are two types of limit stops: MANUAL - A manual (joystick) pan operation stops when a limit stop is reached. SCAN - The dome reverses direction during random, frame, or auto s ...
-
Pelco C2445M-D - page 27
C2443M-C (1/04) 25 AZIMUTH ZERO Azimuth is the pan angle from 0 ° to 359 ° . Azimuth zero is the pan position you specify to be the 0 ° point. Azimuth zero is normally set to magnetic north. Once set, azimuth and compass readings are based on the set Azimuth Zero point. To program azimuth zero: 1. Use the joystick to position the cursor beside S ...
-
Pelco C2445M-D - page 28
26 C2443M-C (1/04) <Power Up> POWER UP ACTION This setting defines a specific activity (scan, preset, pattern) to be performed in the event the power to the dome is cycled. The following settings are available: NONE - No action. AUTO (default) - The dome resumes its prior activity or direction before the power outage. AUTO SCAN - Dome starts ...
-
Pelco C2445M-D - page 29
C2443M-C (1/04) 27 <Line Sync> Line sync refers to a programmable function that allows you to synchronize all cameras within a matrix system. NOTE: Spectra III SE automatically senses V-sync input. No line sync setup is required for Pelco control systems that provide a V-sync signal. For matrix systems that do not output V-sync, there are two ...
-
Pelco C2445M-D - page 30
28 C2443M-C (1/04) <Presets> The Spectra III SE dome system has 80 programmable preset positions. Each preset can be programmed to use pan, tilt, and all programmable camera settings. The presets are numbered 1-32 and 35-82. Presets 33 and 34 are fixed commands that cannot be programmed. Preset 33 is the “flip” command, which will pan the ...
-
Pelco C2445M-D - page 31
C2443M-C (1/04) 29 (See page 9) Quick Programming Guide 3. Edit the preset scene: a. Use the joystick to position the cursor beside EDIT PRESET SCENE. b. Press Iris Open. c. Follow the directions displayed on the monitor . 4. Edit preset camera settings: a. Use the joystick to position the cursor beside EDIT CAMERA SETTINGS. b. Press Iris Open. The ...
-
Pelco C2445M-D - page 32
30 C2443M-C (1/04) <Patterns> A pattern is a memorized, repeating, series of pan, tilt, zoom and preset functions that can be recalled with a command from a controller or automatically by a programmed function (alarm, park or power -up). The Spectra III SE can handle up to four user -defined patterns. Pattern length is based upon memory usage ...
-
Pelco C2445M-D - page 33
C2443M-C (1/04) 31 3. Use the joystick to position the cursor beside a character . Press Iris Open to enter selection. T o clear a character , position the cursor beside BACKSP ACE, and then press Iris Open. 4. When the label is completed, move the cursor the OK. Press Iris Open to return to the Zones menu. To disable a zone (a zone is enabled auto ...
-
Pelco C2445M-D - page 34
32 C2443M-C (1/04) <Window Blanking> W indow blanking allows a user to program up to eight, four -sided, user-defined areas that cannot be viewed by the operator of the dome system. A blanked area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide. Spectra III SE has two style modes for ...
-
Pelco C2445M-D - page 35
C2443M-C (1/04) 33 Window Blanking Disabled Window Blanking Enabled IMPORT ANT : Increase the size of the window if any part of the blanked area is revealed during pan, tilt, and zoom operations. (See page 9) Quick Programming Guide 6. The blanked area can be programmed to turn on or off at a specified zoom point. T o set the zoom point: a. Use the ...
-
Pelco C2445M-D - page 36
34 C2443M-C (1/04) REVERSE A blanked out area can be reversed to make it visible and the areas on both sides of it not visible. The areas above and below the blanking area remain visible. Reversing the window a second time will return it to its original condition. CLEAR WINDOW All areas that have been set for window blanking are cleared. BLANK ALL ...
-
Pelco C2445M-D - page 37
C2443M-C (1/04) 35 <Alarms> The Spectra III SE dome has seven alarm inputs, which can be programmed as high, medium or low priority . When an alarm is received, an input signal to the dome triggers the user -defined action (go to preset, run pattern, etc.) programmed for the alarm. There are three global alarm settings: RESUME - This mode let ...
-
Pelco C2445M-D - page 38
36 C2443M-C (1/04) 3. Select the alarm priority: a. Use the joystick to position the cursor beside ALARM PRIORITY . b. Press Iris Open. The cursor moves to the right. c. Move the joystick up or down to view the available selections. Available settings include HIGH, MEDIUM, and LOW (default). If multiple alarms with different priorities are active a ...
-
Pelco C2445M-D - page 39
C2443M-C (1/04) 37 5. Set the auxiliary to activate: a. Use the joystick to position the cursor beside ACTIV A TE AUX. b. Press Iris Open. The cursor moves to the right. c. Move the joystick up or down to view the following available selections. NO (default) - Not activated. 1 - An alarm action will close AUX 1. 2 - An alarm action will close AUX 2 ...
-
Pelco C2445M-D - page 40
38 C2443M-C (1/04) <Aux> An auxiliary output is a programmable signal from the dome back box that can trigger another device to operate. An auxiliary output is programmable to trigger from an alarm or from a controller . An AUX 1 command from the controller will activate the relay in the dome and operate the device that is connected to the re ...
-
Pelco C2445M-D - page 41
C2443M-C (1/04) 39 (See page 9) Quick Programming Guide <Alert> NOTE: The Alert section only applies to Pressurized Spectra III SE dome systems with software version 1.25 or higher . Spectra III SE systems that are not pressurized or pressurized systems that do not have dome drive software version 1.25 or higher will not display this menu ite ...
-
Pelco C2445M-D - page 42
40 C2443M-C (1/04) ACK ACTION Acknowledge action programs the alert label behavior after the alert condition has been acknowledged. The following settings are available for ACK ACTION: ALW A YS ON - The alert label is displayed until alert conditions are cleared. OFF 8 HRS - The alert label is turned off for 8 hours. Label returns after 8 hours if ...
-
Pelco C2445M-D - page 43
C2443M-C (1/04) 41 <Clear> Use this setting to clear user -defined settings or r eturn the dome to factory default settings. The following are the available CLEAR settings: ALL ZONES - Clears all zones. T o clear a single zone, refer to the Zones section. ALL PRESETS - Clears all presets. T o clear a single preset, refer to the Presets sectio ...
-
Pelco C2445M-D - page 44
42 C2443M-C (1/04) <Password> Spectra III SE features password protection to prevent unauthorized changes to the dome settings. An operator can open the System Information and Display Setup Screens, but cannot access any of the Dome Settings menus. Controller/keyboard commands cannot override password-protected settings. If a keyboard is used ...
-
Pelco C2445M-D - page 45
C2443M-C (1/04) 43 RESET , CYCLE POWER, REBOOT RESET CAMERA Use this function to reset all camera settings to factory default parameters. CYCLE CAMERA POWER If the camera is not operating or if you lose camera control, cycle camera power . Cycling camera power resets the camera but does not change any saved camera settings. REBOOT SYSTEM Reboot the ...
-
Pelco C2445M-D - page 46
44 C2443M-C (1/04) SOFTWARE/LANGUAGE FILE UPLOAD The RJ-45 data port of the dome drive allows access for on-site setup, testing, and uploading of revised operating software and language files. A Pelco field service tool is required to perform these operations. Field service tools include Pelco’ s remote monitor kit (IPS-RMK), remote data port box ...
-
Pelco C2445M-D - page 47
C2443M-C (1/04) 45 SPECIFICA TIONS DD53M22 Signal Format NTSC Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective pixels 768 (H) X 494 (V) Horizontal Resolution >500 TV lines Lens F1.6 (f=4~88 mm optical, 22X optical zoom, 12X electronic zoom) Zoom Speed 3.9 seconds Horizontal Angle of view 47 ° at 4 mm wide zoom; 2.2 ° at 88 mm ...
-
Pelco C2445M-D - page 48
46 C2443M-C (1/04) ® Pelco, the Pelco logo, and Genex are registered trademarks of Pelco. © Copyright 2004, Pelco. ™ Spectra III, PelcoNet, and LowLight are trademarks of Pelco. All rights reserved. REVISION HISTORY Manual # Date Comments C2443M 2/02 Original version. C2443M-A 11/02 Revised Quick Start Guide. C2443M-B 2/03 Manual revised to inc ...
-
Pelco C2445M-D - page 49
W orld Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Orangeburg, New Y ork | Las V egas, Nevada | Eindhoven, The Netherlands | Wokingham, United Kingdom | Montreal, Canada | Singapore ...
Do you have a question concerning Pelco C2445M-D?
Use the form below
If you did not solve your problem by using a manual Pelco C2445M-D, ask a question using the form below. If a user had a similar problem with Pelco C2445M-D it is likely that he will want to share the way to solve it.