English dropdown-ico

Manual Husqvarna Rider 320 AWD

32 pages 4.74 mb
Download

Go to site of 32

Summary
  • Husqvarna Rider 320 AWD - page 1

    E E E E n n n n g g g g l l l l i i i i s s s s h h h h Rider 318 Rider 320 A WD Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine. ...

  • Husqvarna Rider 320 AWD - page 2

    2 – English CONTENTS Contents CONTENTS Contents ...................................................................... 2 Ser vice journal Pre-deliv er y ser vice ..................................................... 3 After the first 8 hours ................................................... 3 INTR ODUCTION Dear Customer , ..................... ...

  • Husqvarna Rider 320 AWD - page 3

    English – 3 Ser vice journal Pre-deliver y service 1 Charge the batter y f or 4 hours at max. 3 amp. 2 Fit steering wheel, seat and any optional equipment. 3 Check and adjust tyre pressure . (60 kP a, 0.6 bar , 9 psi). 4 Adjust cutting unit: Adjust lift springs (effectiv e weight of cutting unit should be 12-15kg / 26.5-33 lb). Adjust cutting uni ...

  • Husqvarna Rider 320 AWD - page 4

    4 – English INTR ODUCTION Dear Customer , Thank y ou f or choosing a Husqvarna Rider . Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented ar ticulated steering. Riders are designed f or maximum efficiency e ven in small or confined areas . The closely grouped controls and pedal-operated h ydrostatic t ...

  • Husqvarna Rider 320 AWD - page 5

    English – 5 KEY T O SYMBOLS Symbols These symbols are on the machine and in the instr uctions. W ARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • Approv ed he ...

  • Husqvarna Rider 320 AWD - page 6

    6 – English KEY T O SYMBOLS Star ting instructions Switch off the engine and take off the ignition cab le bef ore repairs or maintenance Check the engine’ s oil le vel Check tr ansmission oil lev el Lift up the cutting unit Apply the parking brake . If the engine is cold, use the choke Release the parking brake bef ore dr iving ...

  • Husqvarna Rider 320 AWD - page 7

    English – 7 WHA T IS WHA T? Location of the contr ols 12 3 4 6 8 7 9 12 14 13 15 10 11 5 1 Speed limiter f or driving forward 2 Speed limiter f or rev ersing 3 Lifting le ver f or the cutting unit 4 Cutting height adjustment le ver 5 Ignition lock 6 Throttle control/choke control 7 Counter 8 Cov er lock 9 P arking brake 10 Lock b utton f or parki ...

  • Husqvarna Rider 320 AWD - page 8

    8 – English SAFETY INSTR UCTIONS Saf ety instructions These instr uctions are f or your saf ety . Read them carefully . Insure y our Rider • Check the insur ance cov erage f or your ne w Rider. • Contact your insur ance company . • Y ou should hav e fully comprehensive insurance including: third par ty , fire, damage, theft and liability G ...

  • Husqvarna Rider 320 AWD - page 9

    English – 9 SAFETY INSTR UCTIONS • Ne ver allo w children or other persons not trained in the use of the machine to use or ser vice it. Local laws ma y regulate the age of the user . • Use hearing protection to minimise the r isk of hearing impairment. • Ne ver w ear loose-fitting clothing, jewellery or similar that can get caught in movin ...

  • Husqvarna Rider 320 AWD - page 10

    10 – English SAFETY INSTR UCTIONS • Do not tr y to stabilize the machine b y putting your f oot on the ground. • When cleaning the chassis, the machine ma y nev er be driven near v erges or ditches. • When mowing, k eep aw a y from bushes and other objects . • F ollow the manuf acturer’ s recommendations regarding wheel weights or count ...

  • Husqvarna Rider 320 AWD - page 11

    English – 11 SAFETY INSTR UCTIONS • T ake care with battery maintenance. Explosive gases f or m in the batter y . Nev er perform maintenance on the batter y while smoking or in the vicinity of open flames or sparks. This can cause the battery to explode and cause serious injur ies. • Make sure all n uts and bolts are tightened correctly and ...

  • Husqvarna Rider 320 AWD - page 12

    12 – English PRESENT A TION Presentation Cong ratulations on y our choice of an e xcellent quality product that will give y ou great pleasure for man y years . This operator’ s manual describes Rider 318 and Rider 320 A WD . Rider 320 A WD is equipped with all wheel dr ive . The power tr ansmission from the engine is handled by a h ydrostatic t ...

  • Husqvarna Rider 320 AWD - page 13

    English – 13 PRESENT A TION Seat The seat has a jointed attachment on the front edge and can be tipped f orward. The seat can also be adjusted lengthwa ys. Loosen the handles under the seat and adjust it f orwards or backw ards to the desired position. Fueling The engine runs on unleaded petrol with a minimum octane rating of 85 (not mix ed with ...

  • Husqvarna Rider 320 AWD - page 14

    14 – English Driving Bef ore star ting • Read the saf ety instructions and information concer ning the placement of controls and functions bef ore star ting. • P erform daily maintenance before starting as set out in the Maintenance schedule. • Localise and mark stones and other fixed objects to a void collision. • A v oid mowing a wet l ...

  • Husqvarna Rider 320 AWD - page 15

    English – 15 Driving Starting the engine with a weak battery If the batter y is too weak to star t the engine, it should be recharged. When jump leads are used f or emergency star ting, follo w the procedure below: Connecting the jump leads • Connect each end of the red cable to the POSITIVE pole (+) on each batter y , e xercise care not to sho ...

  • Husqvarna Rider 320 AWD - page 16

    16 – English Maintenance Maintenance sc hedule The f ollowing is a list of the maintenance which should be conducted on the machine. For those points not described in this manual, visit an authorised ser vice workshop. 1) First change after 8 hours. When oper ating with a heavy load or at high ambient temperatures , replace e very 50 hours. 2) Ma ...

  • Husqvarna Rider 320 AWD - page 17

    English – 17 Maintenance Cleaning Clean the machine directly after use. It is much easier to wash off grass cuttings bef ore they dr y . Oily dir t can be remov ed using a cold degreasing agent. Spra y on a thin la yer . Rinse at normal water pressure. Do not direct the jet tow ards electrical components or bearings. Do not rinse hot surfaces suc ...

  • Husqvarna Rider 320 AWD - page 18

    18 – English Maintenance 3 If necessar y , the wires can be adjusted by tightening the adjuster nuts on each side of the steering collar . Do not ov er tighten the cables; they should only be drawn in tow ards the steering collar . 4 Unscrew the belt shields and the side protectors . The protectors are fitted on both sides of the machine. 5 Hold ...

  • Husqvarna Rider 320 AWD - page 19

    English – 19 Maintenance 3 Pull back the throttle to the full throttle position and chec k that the choke is no longer actuated. Replacement of fuel filter Replace the fuel filter e very 100 running hours (once per season) or more frequently if it is clogged. Replace the filter as f ollows: 1 Open the engine cov er . 2 Mov e the hose clips aw ...

  • Husqvarna Rider 320 AWD - page 20

    20 – English Maintenance Ignition system The engine is equipped with an electronic ignition system. Only the spark plug requires maintenance. F or recommended spark plug, see T echnical data. Replacing the spark plug 1 Remov e the ignition cable shoe and clean around the spark plug. 2 Remov e the spark plug with a 3/4” (19 mm) spark plug sock e ...

  • Husqvarna Rider 320 AWD - page 21

    English – 21 Maintenance Fitting the cutting head 1 Place the Rider on a flat surf ace and apply the parking brak e. 2 Check that the le ver f or setting the cutting height is in the lowest position and that the lifting le ver f or the cutting unit is in mowing position. 3 Push the equipment frame down and place the catch against the frame. 4 En ...

  • Husqvarna Rider 320 AWD - page 22

    22 – English Maintenance Remo ving the cutting unit 1 Carr y out points 1-6 to put the cutting unit in the ser vice position, see Ser vice position f or the cutting unit. 2 Lower the cutting unit. 3 Open the unit catch. 4 Pull out the cutting unit. Chec king and adjustment of the cutting unit’ s ground pressure T o achiev e the best cutting res ...

  • Husqvarna Rider 320 AWD - page 23

    English – 23 Maintenance 5 Tighten the nuts after adjustment. 6 On completion of the adjustment the unit’ s parallelism should be re-check ed. 7 Screw on the belt shield. 8 Fit the right-hand fender and the front hood. Replacing the cutting unit belts On these cutting units with collision-proof blades , the blades are driven b y one V -belt. Do ...

  • Husqvarna Rider 320 AWD - page 24

    24 – English Maintenance Service position for the cutting unit The cutting head can be placed in the service position to provide easy access f or cleaning, repairs and ser vicing. In the ser vice position the cutting unit is raised and loc ked in the vertical position. Placing in the service position 1 P osition the machine on flat ground. 2 App ...

  • Husqvarna Rider 320 AWD - page 25

    English – 25 Maintenance Chec king the blades T o achiev e the best mowing results it is important that the blades are undamaged and w ell-shar pened. Check that the b lades’ attachment screws are tight. The blades should be balanced after sharpening. Damaged blades should be replaced when hitting obstacles that result in a breakdown. Replacing ...

  • Husqvarna Rider 320 AWD - page 26

    26 – English Lubrication Chec king the engine’ s oil level. Check the oil le vel in the engine when the Rider stands horizontal with the engine s witched off. Do not check the oil with the engine running. Open the engine cov er . Loosen the dipstick, pull it up and wipe it off . Now insert the dipstick again. The dipstick should be completely s ...

  • Husqvarna Rider 320 AWD - page 27

    English – 27 Lubrication Chec king the transmission oil level 1 Remov e the transmission co ver . Undo the two screws (one on each side) and lift off the transmission cov er . 2 Check that there is oil in the tr ansmission’ s oil tank. Rider 318 Fill if necessary with engine oil SAE 10W/40 (class SF–CC). Rider 320 A WD Fill if necessary with ...

  • Husqvarna Rider 320 AWD - page 28

    28 – English T roub leshooting schedule Prob lem Cause Engine does not start There is no fuel in the fuel tank F aulty spar k plug. Def ective ignition cab le. Dir t in the carburettor or fuel line Star ter motor does not tur n ov er the engine Def ect safety s witch Starter motor does not turn over the engine Batter y flat Bad contact between t ...

  • Husqvarna Rider 320 AWD - page 29

    English – 29 Storage Winter stora ge At the end of the season, or if the machine is going to stand idle f or more than 30 days , it should immediately be made ready f or storage. Fuel which is left to stand for long periods (30 da ys or more) can leav e tacky deposits which can b lock the carburettor and interf ere with the engine. Fuel stabilise ...

  • Husqvarna Rider 320 AWD - page 30

    30 – English TECHNICAL D A T A Note 1: The power r ating of the engine indicated is the av erage net output (at specified rpm) of a typical production engine for the engine model measured to SAE standard J1349/ISO1585. Mass production engines may diff er from this value. Actual power output f or the engine installed on the final machine will de ...

  • Husqvarna Rider 320 AWD - page 31

    English – 31 TECHNICAL D A T A EC Dec laration of Conf ormity (Applies to Eur ope only) Husqvarna AB, SE-561 82 Huskv ar na, Sweden, tel.: +46-36-146500, hereby declares that Husqv ar na Rider 318 and Rider 320 A WD from 2014’ s serial numbers and onwards (the year is clearly stated in plain te xt on the rating plate with subsequent serial numb ...

  • Husqvarna Rider 320 AWD - page 32

    ´®z+X§T¶6X¨ 2014-06-16 ´®z+X§T¶6X¨ 1156985-26 Original instructions ...

Manufacturer Husqvarna Category Lawn Mower

Documents that we receive from a manufacturer of a Husqvarna Rider 320 AWD can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- Rider 320 AWD manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna Rider 320 AWD
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna Rider 320 AWD.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna Rider 320 AWD, service manual, brief instructions and user manuals Husqvarna Rider 320 AWD. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna Rider 320 AWD.

Similar manuals

A complete manual for the device Husqvarna Rider 320 AWD, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna Rider 320 AWD by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna Rider 320 AWD.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna Rider 320 AWD - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna Rider 320 AWD, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna Rider 320 AWD, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna Rider 320 AWD - which should help us in our first steps of using Husqvarna Rider 320 AWD
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna Rider 320 AWD
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna Rider 320 AWD in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna Rider 320 AWD?

Use the form below

If you did not solve your problem by using a manual Husqvarna Rider 320 AWD, ask a question using the form below. If a user had a similar problem with Husqvarna Rider 320 AWD it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)