English dropdown-ico

Manual Harman PP38+

38 pages 2.41 mb
Download

Go to site of 38

Summary
  • Harman PP38+ - page 1

    3-90-08422R27_09/12 SA VE THESE INSTRUCTIONS. Installation & Operating Manual “Ce manuel est disponible en Français sur demande” SAFETY NOTICE PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INST ALL AND USE YOUR NEW ROOM HEA TER. F AILURE TO FOLLOW INSTRUCTIONS MA Y RESUL T IN PROPERTY DAMAGE, BODIL Y INJUR Y , OR EVEN DEA TH. FOR USE IN THE U. ...

  • Harman PP38+ - page 2

    3-90-08422R27_09/12 2 PP38+ Pellet Stove "PREVENT HOUSE FIRES" Install and Use Only in Accordance With Manufacturer's Installation and Operation Instructions. Contact Local Building or Fire Ofcials About Restrictions and Installation Inspection in Y our Area. WARNING : THE STRUCTURAL INTEGRITY OF THE MANUF ACTURED HOME FLOOR, W AL ...

  • Harman PP38+ - page 3

    3 PP38+ Pellet Stove 3-90-08422R27_09/12 Safety Information 5 Installation 6 V enting 8 ESP Control 15 Operation 16 Draft T est Procedure 19 Maintenance 20 T roubleshooting 25 Specications    26 Options 27 Corn/Pellet Mixture 28 FuelSpecicationDetails   29 Wiring Diagram 30 W arranty 31 Service Parts 33 T able of Co ...

  • Harman PP38+ - page 4

    4 PP38+ Pellet Stove 3-90-08422R27_09/12 DO NOT INST ALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT . DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. MOBILE HOME INST ALLA TION SHOULD BE DONE IN ACCORDANCE WITH THE MANUF ACTURED HOME AND SAFETY ST ANDARD (HUD), CFR 3280, P ART 24. CAUTION THE STRUCTURAL INTEGRITY ...

  • Harman PP38+ - page 5

    5 PP38+ Pellet Stove 3-90-08422R27_09/12 Assembly and Installation The optional Room Sensor cable attaches to two bare terminals on the rear of the circuit board. These connections are not polarity specic. Unpacking The P38 is bolted (1/4 x 1" hex head bolts) to the skid to prevent movement during shipping. T o free the stove from the skid ...

  • Harman PP38+ - page 6

    6 PP38+ Pellet Stove 3-90-08422R27_09/12 Installing Place thestove on anoncombustible type oor oroor protector that extends a minimum of 6 inches (152mm) to the front of the load door opening, 6 inches (152mm) to the sides of the door opening, and 6 inches to the rear . Floor protection must also extend 2 inch ...

  • Harman PP38+ - page 7

    7 PP38+ Pellet Stove 3-90-08422R27_09/12 V enting Requirements for T erminating the V enting W ARNING: V enting terminals must not be recessed into a wall or siding. NOTE: Only approved pellet vent pipe, wall pass- throughs,andrestops shouldbeusedwhenventing through combustible materials. NOTE: Always take into conside ...

  • Harman PP38+ - page 8

    8 PP38+ Pellet Stove 3-90-08422R27_09/12 V enting V enting A combustion blower is used to extract the combustion gases from the rebox. This causes a  negative pressure in the rebox and a positive pressure in the venting system as shown in Fig. 7. The longer the vent pipe and more elbows used ...

  • Harman PP38+ - page 9

    9 PP38+ Pellet Stove 3-90-08422R27_09/12 Per national building codes, consideration must be given to combustion air supply to all combustion appliances. Failure to supply adequate combustion air for all appliance demands, may lead to back-drafting of those and other appliances. When the appliance is side-wall vented: The air intake is best located ...

  • Harman PP38+ - page 10

    10 PP38+ Pellet Stove 3-90-08422R27_09/12 #2 Preferred method This method also provides excellent venting for normal operation but requires the stove to be installed farther from the wall. The vertical portion of the vent should be three to ve feet high and at least three inches from a combustible wall. This vert ...

  • Harman PP38+ - page 11

    11 PP38+ Pellet Stove 3-90-08422R27_09/12 #4 Installing into an existing chimney This method provides excellent venting for normal operation. This method also provides natural draft in the event of a power failure. If the chimney condition is questionable* you may want to install a liner as in method #7. In some places in the US and Canada it is re ...

  • Harman PP38+ - page 12

    12 PP38+ Pellet Stove 3-90-08422R27_09/12 #6 Installing into an existing replace chimney This method provides excellent venting for normal operation. This method also provides natural draft in the event of a power failure. In some places in the US and Canada it is required that the vent pipe extend all the way to the top of the chimney . The pip ...

  • Harman PP38+ - page 13

    13 PP38+ Pellet Stove 3-90-08422R27_09/12 #8 Installing through the ceiling Through the ceiling vent, follow PL vent manufacturers recommendations when using wall and ceiling pass through. Note: Do not place joints within wall pass- throughs. Fig. 14 PL vent manufacturer's restop spacer and support (See Page 7 for corner installation cleara ...

  • Harman PP38+ - page 14

    14 PP38+ Pellet Stove 3-90-08422R27_09/12 ESP CONTROL Status Light Error Messages 3-Blinks: Indicates that the ESP has gone out of range too many times. Could be an indicator of build up of ash,etc. in theue pipe orheat exchange. Performa Manual Reset. 4-Blinks: Indicates that the room sensor circuit is not compl ...

  • Harman PP38+ - page 15

    15 PP38+ Pellet Stove 3-90-08422R27_09/12 OPERA TION The PP38+ features two operating modes; Stove T emperature Mode and Room T emperature Mode . In Stove T emperature Mode, you select a burn rate and the stove will remain at the same burn rate regardless of the room temperature. In the Room T emperature Mode, with the optional room sensor attached ...

  • Harman PP38+ - page 16

    16 PP38+ Pellet Stove 3-90-08422R27_09/12 OPERA TION The setting above will produce continuous maximum heat output with the distribution blower at full speed. Stove T emperature Mode The setting above will produce continuous medium heat output with the distribution blower at low speed. CAUTION HOT WHILE IN OPERA TION. KEEP CHILDREN, CLOTHING, AND F ...

  • Harman PP38+ - page 17

    17 PP38+ Pellet Stove 3-90-08422R27_09/12 Make sure the unit is plugged into a 120 V AC, 60 HZ electrical source. The power light should be the only light lit. 1. T urn FEED ADJUSTER to desired feed rate . No. 4 is good for most pellets. 4 2. T urn the MODE SELECT OR to “OFF” and then to the desired mode. This will reset control and start the c ...

  • Harman PP38+ - page 18

    18 PP38+ Pellet Stove 3-90-08422R27_09/12 A simple draft test should be performed before andaftercompletingtheuepipeinstallation. T o compare and to record the results for future reference: 1. Plug the unit into a 120 V AC, 60 HZ outlet. 2. Close the hopper lid, front view door , and the ashpan.Neitherpelletsor? ...

  • Harman PP38+ - page 19

    19 PP38+ Pellet Stove 3-90-08422R27_09/12 Maintenance Minimizing Creosote: Whenever wood is burned slowly , the potential exists for creosote to form in the venting. The chimney or venting system should be inspected periodically throughout the heating season to determine if a creosote buildup has occurred. If a signicantlayerofcreosote? ...

  • Harman PP38+ - page 20

    20 PP38+ Pellet Stove 3-90-08422R27_09/12 Maintenance Fig 27 Scraper Blower Cover Latch Blower Wheel Flue Outlet Heat Exchanger Fins Combustion Blower Cover Blower Cover Latch Fig 26 Scraping the burn pot: Whenever adding fuel to the hopper , take the time and scrape the grate surface of the burnpot, using the scrapertool provided.Thisc ...

  • Harman PP38+ - page 21

    21 PP38+ Pellet Stove 3-90-08422R27_09/12 Maintenance Exposed blower wheel and ue opening, NOTE: ESP probe is visible. ESP Probe Fig. 30 Fig. 31 Fig. 33 Burn pot Clean-out plate Latch "open "with blower cover partly removed. Burn pot clean-out is open. Latch "closed "with blower cover in place. Burn pot clean-out is closed. B ...

  • Harman PP38+ - page 22

    22 PP38+ Pellet Stove 3-90-08422R27_09/12 Burn Pot Cleaning and Maintenance 1. Scrape the top holed surface and sides of the burn pot. (Fig 33) It is not necessary to completely remove all material from the burn pot. The excess will be pushed out during the next use. 2. Loosen the (2) wing thumb screws on the lower front angle of the burn pot. (Fig ...

  • Harman PP38+ - page 23

    23 PP38+ Pellet Stove 3-90-08422R27_09/12 Maintenance - Cleaning the Feeder Body Pellet nes may accumulate in the feeder body over a period of time; therefore, a yearly inspection and cleaning of this area must be performed. T ocleanoutnes: 1. Remove the rear cover panels. 2. Remove wing nut and feeder cove ...

  • Harman PP38+ - page 24

    24 PP38+ Pellet Stove 3-90-08422R27_09/12 SMOKE IS VISIBLE COMING OUT OF VENT 1. Air-fuel ratio is too rich. A. Feed rate too high. B. Draft too low caused by a gasket leak. LOW HEA T OUTPUT 1. Feed rate too low 2. Draft too low because of gasket leak. 3. Poor quality or damp pellets 4. Combination of 1 and 2. T rouble-Shooting Cleaning Burn Pot Wh ...

  • Harman PP38+ - page 25

    25 PP38+ Pellet Stove 3-90-08422R27_09/12 25 Weight 212 lbs. Blower 135 cfm Feed Rate approximate .75lb. to 5.5 lbs per hr Hopper Capacity 50 lbs Fuel Wood Pellets Flue Size 3 inch Outside Air Size 2 3/8" I.D. inch Fuse Rating 6 amp Specications 32.375" 10" 28.5" 13.625" 5.25" 22" ...

  • Harman PP38+ - page 26

    26 PP38+ Pellet Stove 3-90-08422R27_09/12 Options Side Heat Shields - Part #1-00-773863 Side heat shields are available to reduce the clearance to combustible materials. Hopper Extension - Part #1-00-08536 The hopper extension allows you to put more pellet fuel in the hopper which extends the burn time on one load of pellets. The hopper extension a ...

  • Harman PP38+ - page 27

    3-90-08422R27_09/12 Harman pellet burning, free-standing stoves and inserts have been tested t o ASTM E1509 for burning shelled corn in a mixture with wood pellets. The listing approves up t o a 50% corn and 50% pellet mixture. Dier ent mixtures of corn will have distinctively di erent burn characteristics depending upon moisture con tent and ...

  • Harman PP38+ - page 28

    28 PP38+ Pellet Stove 3-90-08422R27_09/12 28 PP38+ Pellet Stove Fuel Specications Fuel and Fuel Storage Pelletfuelqualitycanuctuatefrommanufacturerto manufacturer , and even from bag to bag. Hearth & Home T echnologies recommends using only fuelthatiscertiedbythePelletFuelsInstitute(PF ...

  • Harman PP38+ - page 29

    29 PP38+ Pellet Stove 3-90-08422R27_09/12 29 PP38+ Pellet Stove Wiring Diagram -- -- SP ARE NUMBER -- -- -- -- -- 11-12-2008 -- 1:1 773869 B ---- WEIGHT or LENGTH REV REVISIONS P ART NUMBER BY DA TE TITLE DRAWN BY USED ON MATERIAL FINISH MATL PN .015 R MAX BREAK SHARP EDGES (EXCEPT AS NOTED) DO NOT SCALE DRAWING SCALE DATE ±30' ANGULAR FRACTI ...

  • Harman PP38+ - page 30

    3-90-08422R27_09/12 30 PP38+ Pellet Stove 4021-645C 12-29-10 Page 1 of 2 Hearth & Home T echnologies Inc. LIMITED LIFETIME W ARRANTY Hearth & Home T echnologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT author ...

  • Harman PP38+ - page 31

    4021-645C 12-29-10 Page 2 of 2 W ARRANTY CONDITIONS: • This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor . A list of HHT authorized dealers is available on the HHT branded websites. • This warranty is only valid while the HHT appliance remains at the site of original installation. • Co ...

  • Harman PP38+ - page 32

    3-90-08422R27_09/12 Service Parts P38 Pellet Beginning Manufacturing Date: N/A Ending Manufacturing Date: Active IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked ...

  • Harman PP38+ - page 33

    3-90-08422R27_09/12 Service Parts P38 Pellet Beginning Manufacturing Date: N/A Ending Manufacturing Date: Active IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked ...

  • Harman PP38+ - page 34

    3-90-08422R27_09/12 Service Parts P38 Pellet Beginning Manufacturing Date: N/A Ending Manufacturing Date: Active 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.1 1 2.12 2.1 2.2 #2 Pre Serial Number 00808066 Feeder Assembly IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and s ...

  • Harman PP38+ - page 35

    3-90-08422R27_09/12 Service Parts P38 Pellet Beginning Manufacturing Date: N/A Ending Manufacturing Date: Active IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked ...

  • Harman PP38+ - page 36

    3-90-08422R27_09/12 Service Parts P38 Pellet Beginning Manufacturing Date: N/A Ending Manufacturing Date: Active IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked ...

  • Harman PP38+ - page 37

    37 PP38+ Pellet Stove 3-90-08422R27_09/12 Service & Maintenance Log Date Of Service Performed By Description Of Service ...

  • Harman PP38+ - page 38

    At Harman, we build each pr oduct to a standard, not a price . This pow erful heating appliance boasts uncompr omising attention to detail and helps pr eser ve our planet b y using envir onmentall y responsible fuels. (Signatur e of Box er) Y our premium quality hearth pr oduct designed and assembled by the experienced and skilled members at Harman ...

Manufacturer Harman Category Electric Heater

Documents that we receive from a manufacturer of a Harman PP38+ can be divided into several groups. They are, among others:
- Harman technical drawings
- PP38+ manuals
- Harman product data sheets
- information booklets
- or energy labels Harman PP38+
All of them are important, but the most important information from the point of view of use of the device are in the user manual Harman PP38+.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Harman PP38+, service manual, brief instructions and user manuals Harman PP38+. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Harman PP38+.

Similar manuals

A complete manual for the device Harman PP38+, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Harman PP38+ by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Harman PP38+.

A complete Harman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Harman PP38+ - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Harman PP38+, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Harman PP38+, that we can find in the current document
3. Tips how to use the basic functions of the device Harman PP38+ - which should help us in our first steps of using Harman PP38+
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Harman PP38+
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Harman PP38+ in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Harman PP38+?

Use the form below

If you did not solve your problem by using a manual Harman PP38+, ask a question using the form below. If a user had a similar problem with Harman PP38+ it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)