-
Chicago Electric 93213 - page 1
ELECTRIC CHAINSA W SHARPENER Model 93213 SET UP AND OPERA TING INSTRUCTIONS Visit our website at: http://www .harborfreight.com Read this material before using this product. Failure to do so can result in serious injury . SA VE THIS MANUAL. Copyright © 2005 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork ...
-
Chicago Electric 93213 - page 2
Page 2 For technical questions, please call 1-800-444-3353. SKU 93213 SA VE THIS MANUAL Keep this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures. Write the product’ s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product ha ...
-
Chicago Electric 93213 - page 3
Page 3 For technical questions, please call 1-800-444-3353. SKU 93213 attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this tool and do not use this tool for a purpose for which it was ...
-
Chicago Electric 93213 - page 4
Page 4 For technical questions, please call 1-800-444-3353. SKU 93213 processes) can result in eye, skin and breathing irritation. Always use a NIOSH (National Institute for Occupational Safety and Health) approved respirator and safety goggles. Avoid skin exposure. People with pacemakers should 24. consult their physician(s) before use. Electromag ...
-
Chicago Electric 93213 - page 5
Page 5 For technical questions, please call 1-800-444-3353. SKU 93213 GROUNDING TO PREVENT ELECTRIC SHOCK AND DEA TH FROM INCORRECT GROUNDING WIRE CONNECTION: Check with a qualied electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding pro ...
-
Chicago Electric 93213 - page 6
Page 6 For technical questions, please call 1-800-444-3353. SKU 93213 Extension Cords Grounded 1. tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. As the distance from the supply outlet 2. increases, you must use a heavier gauge extension cord. Using extension cords with inadequate ...
-
Chicago Electric 93213 - page 7
Page 7 For technical questions, please call 1-800-444-3353. SKU 93213 SPECIFICA TIONS Motor 120 V~, 0.75 A (Load), Direct Drive RPM 4200 Vise Capacity 0.80” to 0.50” T able / Vise Angles 35° Right to Left Arbor Diameter 7/8” Wheel Dimensions 4-1/4” Dia. x 1/8” Thick Working time S3:10S ON / 15S OFF Note: Performance of this tool (if powe ...
-
Chicago Electric 93213 - page 8
Page 8 For technical questions, please call 1-800-444-3353. SKU 93213 ASSEMBL Y W ARNING! Unplug the tool before changing grinding wheels, or before making any adjustments to the tool. Installation Install the Sharpener to a workbench 1. before use. FIGURE 1 1/4” Hole with Bolt Lock Wheel (18) 1. When installing the sharpener on a workbench, make ...
-
Chicago Electric 93213 - page 9
Page 9 For technical questions, please call 1-800-444-3353. SKU 93213 Mounting a Grinding Wheel Refer to the Assembly Drawing on page 10. FIGURE 3 Lock Stop (6) T op Housing (4B) Grinding Wheel Cover (1 1B) 1. Raise the T op Housing (4B) and lock it in the up position by tightening the Lock Stop (6). Remove the four screws holding the 2. Grinding W ...
-
Chicago Electric 93213 - page 10
Page 10 For technical questions, please call 1-800-444-3353. SKU 93213 OPERA TION W ARNING! Unplug the unit before adjusting chain to be sharpened. Refer to the Assembly Drawing on page 10 and the various photographs. Note: Raise the T op Housing (4B) while adjusting the chain. Clean the chain before sharpening. 1. W ash it with a nonammable sol ...
-
Chicago Electric 93213 - page 11
Page 1 1 For technical questions, please call 1-800-444-3353. SKU 93213 FIGURE 7 Lock Stop (6) 6. Hold it at that position while you tighten the Lock Stop (6) so that the wheel will only go down to that point. See FIGURE 7 . Depending on the amount of material 7. you wish to remove, tighten or loosen the Lower Knob (26) and set the Lock Nut. See FI ...
-
Chicago Electric 93213 - page 12
Page 12 For technical questions, please call 1-800-444-3353. SKU 93213 FIGURE 10 3. Slowly lower the grinding wheel as shown in FIGURE 10 . If you notice slight errors in your settings, turn off the unit and unplug it before you make your adjustments. Note: A good grind occurs when the contact between the wheel and the teeth are gradual and smooth. ...
-
Chicago Electric 93213 - page 13
Page 13 For technical questions, please call 1-800-444-3353. SKU 93213 MAINTENANCE Keep the Sharpener clean and free of 1. dust, metal debris and dirt. Check the Grinding Wheel before each 2. use to make sure it isn’t damaged. Do not use a grinding wheel if it is chipped, cracked, or worn. Y ou can check if the wheel has cracks not visible to the ...
-
Chicago Electric 93213 - page 14
Page 14 For technical questions, please call 1-800-444-3353. SKU 93213 P ARTS LIST Part Description Q’ty 1 Screw 3 2 Motor Cover 1 3 Power Cord 1 4B T op Housing 1 5B Rocker Switch 1 6 Lock Stop 1 7 Grinding Wheel Base 1 8 Grinding Wheel 1 9 Grinder Lock Cap 1 10 Screw 2 1 1B Grinding Wheel Cover 1 12 O-ring 2 13 Punching Axis 1 14 T orsion Sprin ...
-
Chicago Electric 93213 - page 15
Page 15 For technical questions, please call 1-800-444-3353. SKU 93213 ASSEMBL Y DRA WING Chain Mounting Assembly Set 39 ...
-
Chicago Electric 93213 - page 16
Page 16 For technical questions, please call 1-800-444-3353. SKU 93213 LIMITED 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days fro ...
Do you have a question concerning Chicago Electric 93213?
Use the form below
If you did not solve your problem by using a manual Chicago Electric 93213, ask a question using the form below. If a user had a similar problem with Chicago Electric 93213 it is likely that he will want to share the way to solve it.