English dropdown-ico

Manual Pelco DX8000-MUX16

24 pages 8.99 mb
Download

Go to site of 24

Summary
  • Pelco DX8000-MUX16 - page 1

    DX8000-MUX16 Installation Manual C1601M (6/04) Digital Video Recorder DX8000 ...

  • Pelco DX8000-MUX16 - page 2

    Protecting people and property in a million locations worldwide. ...

  • Pelco DX8000-MUX16 - page 3

    C1601M (6/04) 1 Introduction The following instructions serve as a guide for the installation of the DX8000-MUX16 analog output adapter . PARTS LIST Qty Description 1 DX8000-MUX16 multiplexing analog output card 1 Adhesive-backed part label Figure 1. DX8000-MUX16 Analog Output Card TOOLS NEEDED 1 Phillips-head screwdriver #1 (nonmagnetic) 1 Properl ...

  • Pelco DX8000-MUX16 - page 4

    2 C1601M (6/04) Getting Ready 1. Familiarize yourself with the instructions throughout this manual. 2. Check that you have all the necessary parts and tools. Refer to the Parts List and T ools Needed sections. 3. Shut down the DX8000 Series DVR unit. Refer to DX8000 Installation Manual or Operations and Programming Manual for instructions on shutti ...

  • Pelco DX8000-MUX16 - page 5

    C1601M (6/04) 3 Figure 3. Removing Power Cord from Unit ...

  • Pelco DX8000-MUX16 - page 6

    4 C1601M (6/04) Figure 4. ESD Protection 5. Ensure that the DX8000 Series DVR and all of its components are protected against electro static discharge (ESD). Before handling any electronic components, you should take steps to properly ground yourself so that any built-up static electric charges are dissipated away from the unit. The most effective ...

  • Pelco DX8000-MUX16 - page 7

    C1601M (6/04) 5 Prepare the Unit OPEN THE UNIT CHASSIS WARNING: The chassis assembly includes parts with sharp edges. T o avoid injury , use caution when working in and around the DX8000’ s chassis and components. 1. If the DX8000 is mounted in a rack, remove it and transport it to an area that will provide full access to the unit chassis: a. Dis ...

  • Pelco DX8000-MUX16 - page 8

    6 C1601M (6/04) 3. Using a Phillips-head screwdriver , remove the chassis cover: WARNING: Make sure unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the DX8000 chassis cover . Refer to the Getting Ready section. a. Remove the two top-most screws on the left and right side panels of the DX8000. Ref ...

  • Pelco DX8000-MUX16 - page 9

    C1601M (6/04) 7 COMPONENT LA YOUT Figure 6 shows the location of your DX8000 Series DVR’ s major components. Certain cables and components have been omitted from the illustrations in this manual for the purpose of clarity . Figure 6. DX8000 Interior POWER SUPPLY DIMM SOCKETS (RAM) CPU VGA CARD PCI SLOT 1 2 3 4 5 6 REAR CROSS-BRACE FRONT CROSS-BRA ...

  • Pelco DX8000-MUX16 - page 10

    8 C1601M (6/04) REMOVE THE REAR CROSS-BRACE 1. Using a Phillips-head screwdriver , remove the two flat-head screws that secure the rear cross-brace. Refer to Figure 7. Figure 7. Removing Rear Cross-Brace ...

  • Pelco DX8000-MUX16 - page 11

    C1601M (6/04) 9 2. Move the rear cross-brace aside and keep the screws for later use. Figure 8. Moving Rear Cross-Brace to Rear of Unit ...

  • Pelco DX8000-MUX16 - page 12

    10 C1601M (6/04) Install the DX8000-MUX16 Card 1. Locate PCI Slot 2 on the system motherboard. Refer to Figure 9. Figure 9. Location of PCI Slot 2 PCI SLOT2 ...

  • Pelco DX8000-MUX16 - page 13

    C1601M (6/04) 11 2. Remove the slot cover covering PCI Slot 2: a. Using a Phillips-head screwdriver , remove the screw that fastens the slot cover to the chassis. Refer to Figure 10. Retain this screw for use in step 4d. b. Remove the slot cover from PCI Slot 2. Figure 10. Slot Cover for PCI Slot 2 ...

  • Pelco DX8000-MUX16 - page 14

    12 C1601M (6/04) 3. Carefully remove the DX8000-MUX16 card from its static-safe packaging. Handle the adapter card by its edges and slot cover , and avoid contact with the card’ s components, connectors, and conductive leads. 4. Insert the DX8000-MUX16 card in PCI Slot 2: a. Carefully move aside any cables blocking access to PCI Slot 2. b. Insert ...

  • Pelco DX8000-MUX16 - page 15

    C1601M (6/04) 13 d. Using the screw you removed in step 2a, secure the DX8000-MUX16 card to the chassis. Refer to Figure 12. Figure 12. Securing the DX8000-MUX16 Card 4d ...

  • Pelco DX8000-MUX16 - page 16

    14 C1601M (6/04) 5. Connect video data cables: a. Connect the rear video input ribbon cable from the primary capture card to the DX8000-MUX16 card. Refer to Figure 13. Figure 13. Primary Capture Card Video Input Cable 5a ...

  • Pelco DX8000-MUX16 - page 17

    C1601M (6/04) 15 b. Connect the front video input ribbon cable from the secondary capture card to the connector on the daughter board of the DX8000-MUX16. Refer to Figure 14. Figure 14. Secondary Capture Card Video Input Cable 5b ...

  • Pelco DX8000-MUX16 - page 18

    16 C1601M (6/04) c. Connect the video output ribbon cable from the DX8000-MUX16 card to the VGA card. Refer to Figure 15. Figure 15. Video Data Cable Connections 5c ...

  • Pelco DX8000-MUX16 - page 19

    C1601M (6/04) 17 Reassemble the Unit 1. Replace the rear cross-brace and secure it with the flat-head screws you set aside earlier . Refer to Figure 16. Figure 16. Replacing Front Cross-Brace ...

  • Pelco DX8000-MUX16 - page 20

    18 C1601M (6/04) 2. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 17. Figure 17. Replacing Chassis Cover ...

  • Pelco DX8000-MUX16 - page 21

    C1601M (6/04) 19 3. Attach the silver part label that came in your upgrade kit to the inside of your DVR’ s front door . a. Remove the paper backing from the part label. b. Carefully place the label, adhesive-side down, on a free section of the inside of the door . c. Press down firmly to ensure that the label properly adheres to the inside of th ...

  • Pelco DX8000-MUX16 - page 22

    20 C1601M (6/04) ON/OFF 4. Reinstall the unit in a rack enclosure if necessary , and reconnect all cables and peripheral equipment that you removed earlier . 5. Plug the power cord back into the power supply and then into the wall. 6. T urn on the power switch and allow the unit to start up and find the new hardware. This may take several minutes. ...

  • Pelco DX8000-MUX16 - page 23

    PRODUCT W ARRANTY AND RETURN INFORMA TION PRODUCT W ARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on the following fixed camera mode ...

  • Pelco DX8000-MUX16 - page 24

    C1601M (6/04) ® Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 2004, Pelco. All rights reserved. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | ...

Manufacturer Pelco Category Camcorder

Documents that we receive from a manufacturer of a Pelco DX8000-MUX16 can be divided into several groups. They are, among others:
- Pelco technical drawings
- DX8000-MUX16 manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco DX8000-MUX16
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco DX8000-MUX16.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco DX8000-MUX16, service manual, brief instructions and user manuals Pelco DX8000-MUX16. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco DX8000-MUX16.

Similar manuals

A complete manual for the device Pelco DX8000-MUX16, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco DX8000-MUX16 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco DX8000-MUX16.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco DX8000-MUX16 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco DX8000-MUX16, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco DX8000-MUX16, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco DX8000-MUX16 - which should help us in our first steps of using Pelco DX8000-MUX16
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco DX8000-MUX16
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco DX8000-MUX16 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco DX8000-MUX16?

Use the form below

If you did not solve your problem by using a manual Pelco DX8000-MUX16, ask a question using the form below. If a user had a similar problem with Pelco DX8000-MUX16 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)