Manual MTD E2B5

32 pages 6.48 mb
Download

Go to site of 32

Summary
  • MTD E2B5 - page 1

    PRINTED IN U .S.A. Oper ator’ s Man ual FORM NO . 770-10540D (5/2004) IMPORT ANT : Read saf ety r ules and instructions carefully before op er ating equipment. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest- covered, brush-covered or grass-covered l and unless the engine? ...

  • MTD E2B5 - page 2

    2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Manu al is an important part of your new snow throw er. It will help you to assemble, prepare and maintain the unit for best performance. Plea se read and understand wh at it says. Before you st art assembling your ne w equipment , please locate the model pla te on the equipment and copy th ...

  • MTD E2B5 - page 3

    3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out importan t safety instruct ion s which, if not followed, could endanger the personal safety and/or property of y ourself and others. Read and follow all instructions in this manual be fore attempting to operate this machine . Fail ure to comply with thes e in structions ...

  • MTD E2B5 - page 4

    4 odorless and deadly gas. 6. Do not ope rate machine while u nder the infl uence of alcohol or drugs. 7. Muffler and engine become hot an d can cause a burn. Do not touch. 8. Exercise extreme caution wh en operating on or crossing gravel surfaces. Stay alert for hidden hazards or traffic. 9. Exercise caution when changing direction and while opera ...

  • MTD E2B5 - page 5

    5 SECTION 2: ASSEMBLING YOUR SNOW THROWER NOTE: This Operator’s Manual covers several models. Snow thrower feat ures vary by model . Not all features di scussed in this m anual are ap plicable to a ll snow throwe r models. Unpacking From Carton • Cut along corners of the carto n and lay it down flat. Remove packing material. • Remove any loos ...

  • MTD E2B5 - page 6

    6 SECTION 3: KNOW YOUR SNOW THROWER Figure 3 Auger Control Handle Located on the upper handle, the auger control hand le is used to engage and diseng age the auger. The snow thrower is designed to propel by the rotation of the auger. Pull th e auger control handle back against the upper handle to engage the auger; release to disengage . Discharge C ...

  • MTD E2B5 - page 7

    7 SECTION 4: OPERATING YOUR SNOW THROWER Before Starting • The spark plug wire was disconnected for safety . Attach spark plu g wire to spark plug before starting. Gas and Oil Fill-Up • Check oil and gasoline level and ad d if necessary. Follow related instructions in the separate en gine manual packed with your snow thr ower. T o Start Engine ...

  • MTD E2B5 - page 8

    8 T o Stop Engine • To stop e ngine, turn ignit ion key counter-clockwise. Disconnect the spark plug wire fr om the spark plug to prevent accidental st arting while equipment is unattended . To help pr event possible f reeze-up of starter, proceed as follows: • Run engine for a few minutes before stopping to help dry off any moisture on the eng ...

  • MTD E2B5 - page 9

    9 SECTION 5: MAKING ADJUSTMENTS Shave Plate • To check the adjustmen t of the shave plate, place the unit on a level surfac e. See Fi gure 6. The wheels, shave plate and aug ers should all contact level surface. Note that if the shave plate is adjusted too high, sn ow may blow under the housing. If the sh ave plate wears out ex cessively, or the ...

  • MTD E2B5 - page 10

    10 SECTION 6: MAINTAINING YOUR SNOW THROWER Replacing Belt • Remove the belt cover by remo ving five hex screws. See Figure 8. Figure 8 • Pull up on the idler pulley and slip the belt of f the engine and auger pulley. See Figure 9. Figure 9 • Reassemb le new belt. Reinstall th e belt cover. Replacing Shave Plate The shave plate is att ached t ...

  • MTD E2B5 - page 11

    11 SECTION 8: TROUBLESHOOTING GUIDE For repairs b eyond the m inor adjustm ents listed above, cont act your ne arest author ized service representa tive or call for the Customer Support Center. Refer to th e engine manual for more engine re lated information. For US Cust omers: 1- (330) 2 20-4MTD (4683) or 1- (800)- 800-7310 For Canadian Cus tomers ...

  • MTD E2B5 - page 12

    12 10 SECTION 9: PARTS LIST/PARTS LISTS/LISTE DE PIÈCES DETACHÉES 41 39 44 35 35 44 35 44 33 43 42 18 3 14 21 8 20 10 28 22 3 1 13 13 18 2 16 7 29 12 17 25 22 28 19 15 30 6 9 9 13 31 23 27 CABLE T O BE ABO VE WHEEL AXEL 32 38 45 40 12 12 17 17 46 37 36 24 49 26 52 50 48 47 51 34 3 53 14 4 ...

  • MTD E2B5 - page 13

    REF PA R T NO . NO . N° DE N° DE RÉF PIÈCE DE SCRIP TION DE SCRIP TION 1 684-04027A Auger Ass’y 21" comp. w/Solid Shaft Ensemble de la tarière complète avec arbre solide 2 684-04026 Auger Housing Ass’y 21" Logement de la tarière de 21 po 3 710-0134 Carriage Bolt 1/4-20 x .62 Boulon ordinaire 1/4-20 x 0,62 4 710-3008 Hex Hd. Cap ...

  • MTD E2B5 - page 14

    REF PA R T NO . NO . N° DE N° DE RÉF PIÈCE DE SCRIP TION DE SCRIP TION 1 710-04071 Carriage Screw 5/16-18 x 1.0 Vis ordinaire 5/16-18 x 1,0 2 710-0451 Carriage Bolt 5/16-18 x .75 Boulon ordinaire 5/16-18 x 0,75 3 712-4063 Hex Patch l-Nut 5/16-18 Écrou de blocage à six pans 5/16 - f il. 18 4 720-0284 Handle Knob Assembly Bouton 5 731-04127 Low ...

  • MTD E2B5 - page 15

    REF PA R T NO . NO . N° DE N° DE RÉF PIÈCE DE SCRIP TION DE SCRIP TION 1 629-0071 Extension Cord 10 Ft. Corde à ralonge de 10 pi de lg. 2 710-0627 Hex Hd. Cap Screw 5/16-24 x .75 Vis à tête hex. 5/16-24 x 0,75 3 710-0409 Hex Bolt 5/16-24 x 1.75 Boulon hex. 5/16-24 x 1,75 4 710-0654A Hex Wash HD T ap Scr 3/8-16 x .88 Vis autotaraudée 3/8-16 ...

  • MTD E2B5 - page 16

    MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth be low is given by MTD LLC with respect to new merchandise purchase d a nd used in the United States and/or its territories and possess ions, and by MTD Products Limited with respect to new merchandise pur chased and used in Canada and/ or its territories and possessions (e it ...

  • MTD E2B5 - page 17

    17 NOTES ...

  • MTD E2B5 - page 18

    15 NOTES ...

  • MTD E2B5 - page 19

    GARANTIE DU F ABRICANT POUR: La garantie limitée qui est énoncée ci-dessous e st offerte par MTD LLC pour toutes les marcha ndises neuves achetées et utilisées aux États-Unis, dans ses possessio ns et territoires, et par MTD Products Limited, po ur toutes les march andises achetées et utilisées au Canada et /ou ses te rritoires (l’une ou ...

  • MTD E2B5 - page 20

    13 CHAPITRE 8: DÉPANNAGE Addressez-vous à la station tech nique la plus proche ou appelez le service après-vente pour toute réparation autre que les ajustements mineurs mentionné s ci-dessus. Consultez la notice d’utilisation du mo teur pour tout renseignement supplém entaire concernant le moteur. Pour clients des États-Unis: 1 -330-220-4M ...

  • MTD E2B5 - page 21

    12 CHAPITRE 7: REMISAGE HORS SAISON AVERTISSEMENT: Ne remisez jamais un moteur contena nt encore du carburant à l’intérieur ou dans un e ndroit mal aéré si les vapeurs d’essence ri squent d’entrer en contact avec une flamme (veille us e d’un appareil de chauffage, d’un chau ffe- eau, d’un sèche- linge, etc.). • Nettoyez complète ...

  • MTD E2B5 - page 22

    11 CHAPITRE 6: ENTRETIEN DE LA SOUFFLEUSE AVERTISSEMENT: Débra yez la manette de commande et arrê tez le moteur avant de faire une répar ation, un ajustement quelconque ou d’exam iner la mac hine. Attendez que la tarière/turbine se soit complètement immobilisée. Débranchez le fil de la bougie et mettez- le à la terre contre le moteur pour ...

  • MTD E2B5 - page 23

    10 CHAPITRE 5: RÉGLAGES AVERTISSEMENT: N’essayez jamais de régler le moteur pendant qu’il tourne (â moins d’indications contraires de la part du fabricant). Réglage de la plaque de raclage • Pour vérif ier le réglag e, placez la souffleus e sur une surface plat e. La plaque doit être réglée de manière que les roues, la plaq ue et ...

  • MTD E2B5 - page 24

    9 REMARQUE: Couvrez toujours l’évent du bouton de l’amorceur en appuyant. Un amorça ge supplémentaire peut être nécessaire lors du premie r démarrage si la température est inférieur e à 15°F (-9°C). • Tirez lenteme nt sur la poignée du dé marreur jusqu’à ce que vous sentiez une lé gère résistance. Laissez la cor de s’enro ...

  • MTD E2B5 - page 25

    8 CHAPITRE 4: UTILISATION DE LA SOUFFLEUSE Ava n t le d é m a rr a g e AVERTISSEMENT: Avant de commencer le moteur, lisez, comprenez et suivez t outes les instructi ons et les consignes sur la machin e et dans ce notic e avant le fonc tionnemen t. • Le fil de bougie d'alluma ge a été débranché pour la sûreté. Atta chez le fil de bougi ...

  • MTD E2B5 - page 26

    7 CHAPITRE 3: CONNAÎTRE VOTRE SOUFFLEUSE Figure 3 AVERTISSEMENT: Familiarisez-vous avec les commandes et la bonne utilisation de cette machine avant de vous en servir. Apprenez à arrêter la machine et à dé brayer rapidement les commandes. Manette de commande Elle se trouve sur le guidon supérieu r et sert à enclencher et à désenclencher la ...

  • MTD E2B5 - page 27

    6 CHAPITRE 2: MONTAGE REMARQUE: Cette notice d’utilisation couvre plusieurs modèles. Les trai ts du souffleuse va rient par le modèle . Pas toutes les traits discutées dans ce notice sont applicables à tous les modèles de souffleuse. Déballage du carton • Découpez le carton en su ivant les coins, puis étalez-le. Sort ez les garnitures. ...

  • MTD E2B5 - page 28

    5 sécurité, vérifiez souven t tous les composants et remplacez-les par des pièce s authentiques seulement. L’utilisation de pièces qui ne sont pas conformes aux spécifications de l’équipement d’origine peuvent donne r lieu à de mauvaises performanc es et com promettre la sécurité de l’utilisateur. 6. Vérifiez fréque mment que le ...

  • MTD E2B5 - page 29

    4 pour permet tre l’expansion du carburant. g. Resserrez bie n le capuchon d’esse nce. h. En cas de débor dement, essuyez toute éclaboussur e sur le moteur et la ma chine. Déplacez la machine et attende z 5 minutes avant de la remettre en marche . i. Ne remisez jamais la machine ou les bidons d’essence à l’intérieur s’il y a une flam ...

  • MTD E2B5 - page 30

    3 CHAPITRE 1: IMPORTANT CONSIGNES DE SÉCURITÉ AVERTISSEMENT: Ce symbole attire votre atte ntion sur des consignes de sécurité import antes qui, si elles ne sont pas r espectées, peuvent mett re en danger non seulement vot re personne et vos biens, mais aussi ceux d’autrui. Prière de lire toutes les instructions figurant dans cette no tice d ...

  • MTD E2B5 - page 31

    2 TABLE DES MATIÈRES POUR TROUVER LE NUMÉRO DE MODÈLE Cette notice d’utilisation est une pièce importante de votre nouvelle souffleuse. E lle vous fournit les renseignements nécessaires à l’assembla ge, à la préparation et à l’entreti en de votre machin e. Veuillez donc la lire attentivemen t et vous assurer de bien comprendre tout e ...

  • MTD E2B5 - page 32

    Notice d’utilisation FORM NO . 770-10540D (5/2004) Souffleuse à une phase IMPRIMÉ A UX ÉT A TS-UNIS. IMPORT ANT : Lisez attentivement les règle s de sécurité et les instructions avant de mettr e en marche la machine. Avertissement: Cet appareil est équipé d’un moteur à combustion interne. Pour cett e raison, il ne doit pas être utilis ...

Manufacturer MTD Category Snow Blower

Documents that we receive from a manufacturer of a MTD E2B5 can be divided into several groups. They are, among others:
- MTD technical drawings
- E2B5 manuals
- MTD product data sheets
- information booklets
- or energy labels MTD E2B5
All of them are important, but the most important information from the point of view of use of the device are in the user manual MTD E2B5.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals MTD E2B5, service manual, brief instructions and user manuals MTD E2B5. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product MTD E2B5.

Similar manuals

A complete manual for the device MTD E2B5, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use MTD E2B5 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of MTD E2B5.

A complete MTD manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual MTD E2B5 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the MTD E2B5, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the MTD E2B5, that we can find in the current document
3. Tips how to use the basic functions of the device MTD E2B5 - which should help us in our first steps of using MTD E2B5
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with MTD E2B5
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of MTD E2B5 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning MTD E2B5?

Use the form below

If you did not solve your problem by using a manual MTD E2B5, ask a question using the form below. If a user had a similar problem with MTD E2B5 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)