English dropdown-ico

Manual Hobart H0210G1

20 pages 1.27 mb
Download

Go to site of 20

Summary
  • Hobart H0210G1 - page 1

    701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 34622 Rev. B (Sep. 2003) HO210 SERIES RA CK O VENS WITH ELECTR ONIC O VEN CONTR OL MODEL HO210E1 (ELECTRIC) ML-132180 HO210E2 (ELECTRIC) ML-132181 HO210G1 (GAS) ML-132182 HO210G2 (GAS) ML-132183 ...

  • Hobart H0210G1 - page 2

    IMPORT ANT FOR Y OUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FR ...

  • Hobart H0210G1 - page 3

    – 3 – MODEL HO210G1 ...

  • Hobart H0210G1 - page 4

    – 4 – TABLE OF CONTENTS GENERAL ............................................................................................................................................. 5 INSTALLATION .................................................................................................................................... 5 OPERATION ............ ...

  • Hobart H0210G1 - page 5

    – 5 – OPERA TION AND CARE OF MODELS HO210G1/HO210G2 GAS RA CK O VENS and HO210E1/HO210E2 ELECTRIC RA CK O VENS KEEP THIS MANU AL FOR FUTURE USE GENERAL Models HO210G1/HO210G2 (gas) and HO210E1/HO210E2 (electric) Rack Ovens accommodate roll-in racks. They are equipped with an electronic oven control for baking and/or steaming applications. A mec ...

  • Hobart H0210G1 - page 6

    – 6 – OPERA TION WARNING: THE RACK OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, SERVICING OR CLEANING THE OVEN. CONTROLS PL-53621 SET TEMP. OVEN TEMP. Actual Temperature In Oven Max.Temp. 525 F / 274 C HEAT ON O O TIMER STEAM DELAY (AIRFLOW) ON Seconds ON Minutes Minutes Set Remaining Heat is disabled during this delay ON QUICK SET Numb ...

  • Hobart H0210G1 - page 7

    – 7 – CONTROL GUIDE Y E K N O I T C A Y A L P S I D . P M E T . e r u t a r e p m e t d e r i s e d e h t t e s o t s s e r P . d a p y e k r e b m u n e h t g n i s u e u l a v e h t r e t n E t e s e h t s y a l p s i d w o d n i w . P M E T T E S e b l l i w t h g i l N O T A E H e h T . e r u t a r e p m e t . g n i t a e h e r p s i n e v ...

  • Hobart H0210G1 - page 8

    – 8 – PL-53621 SET TEMP. OVEN TEMP. Actual Temperature In Oven Max.Temp. 525 F / 274 C HEAT ON O O TIMER STEAM DELAY (AIRFLOW) ON Seconds ON Minutes Minutes Set Remaining Heat is disabled during this delay ON QUICK SET Number 0-84 TEMP. CLEAR or SET TIMER CLEAR or SET STEAM CLEAR or SET DELAY CLEAR or SET QUICK SET START STOP RESUME CLEAR or SE ...

  • Hobart H0210G1 - page 9

    – 9 – BASIC OPERATION WARNING: THE OVEN AND ITS PARTS ARE HOT. TO PREVENT BURNS, USE HOT PADS OR PROTECTIVE MITTS WHEN LOADING OR UNLOADING THE OVEN. 1 . Preheat the oven. 2 . Confirm that the door is closed. This enables the rack carrier to lift and rotate. 3 . Manually select baking settings: • Press TIMER and enter the desired value on the ...

  • Hobart H0210G1 - page 10

    – 10 – PROGRAMMING THE QUICK SET MENU QUICK SET stores up to 84 programs that can be stored in memory and recalled by number when needed. A program is a set of baking instructions - TEMP., TIMER, STEAM and DELAY settings - that the operator defines for any baking operation. 1 . Press TEMP. and enter 99 on the number keypad. Repeat this step for ...

  • Hobart H0210G1 - page 11

    – 11 – Changing Quick Set Programs 1 . When the power is turned on, the oven defaults to QUICK SET-1. 2 . Press TEMP. and enter 99 on the number keypad. Repeat this step for TIMER, STEAM and DELAY. 3 . Wait for displays to change to 0. 4 . Press TEMP. and enter the new temperature value on the number keypad. Repeat this step for TIMER, STEAM an ...

  • Hobart H0210G1 - page 12

    – 12 – TEMPERATURE AND TIMER CONTROL SETTINGS The temperature and timer controls are factory set to degrees Fahrenheit with minutes set and minutes remaining. If desired, the controls can be changed to degrees Celsius and/or hours and minutes remaining as follows: 1 . Press TEMP. and enter 99 on the number keypad. Do the same for TIMER, STEAM a ...

  • Hobart H0210G1 - page 13

    – 13 – SHUTDOWN 1 . Remove all remaining product. 2 . Press TEMP. to shut off heat. 3 . Allow the oven to cool and then turn the power switch to the OFF position. 4 . Clean the baking chamber. (See CLEANING.) 5 . For lengthy shutdowns, shut off main power, gas and water supplies. CLEANING WARNING: THE RACK OVEN AND ITS PARTS ARE HOT. USE CARE W ...

  • Hobart H0210G1 - page 14

    – 14 – MAINTENANCE WARNING : THE RACK OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, SERVICING OR CLEANING THE OVEN. WARNING : DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. GENERAL As Needed • Inspect the area around the oven. The area must be free and clear from combustibles. There must be no ob ...

  • Hobart H0210G1 - page 15

    – 15 – O WNER PREVENTIVE MAINTENANCE PR OCEDURE INTRODUCTION This customer preventive maintenance (PM) section includes procedures to inspect for proper operation and cleaning of components. Owner Preventive Maintenance Procedures are written for gas ovens. They can also be used for electric ovens by omitting the steps that refer to components ...

  • Hobart H0210G1 - page 16

    – 16 – Clean and Vacuum Components and Control/Burner Compartment Areas 1 . Clean the control/burner compartment area (Fig. 3) of dust and/or lint accumulation. 2 . Vacuum the control/burner compartment floor of dust and/or lint accumulation. 3 . Gain access to the top of oven and clean dust that may have accumulated on top of circulation blowe ...

  • Hobart H0210G1 - page 17

    – 17 – Inspect Door Components 1 . Check loading door latch. A. Check door gasket for good condition. If door gasket needs replacement, contact your local Hobart office for service. B. Check loading door latch (Fig. 5), latch must fully extend when door is closed and contacting door gasket. Leave about 1 / 8 " gap between latch and striker ...

  • Hobart H0210G1 - page 18

    – 18 – Inspect Air Louvers 1 . Check air louvers (shutters) (Fig. 9) inside oven and tighten any loose screws. 2 . Check oven interior, tighten or replace loose or missing panel screws. Also check floor anchors. Fig. 9 Inspect Cavity Vent 1 . Check vent for proper operation. A. Push vent button (Fig. 10) on control panel to open vent and then p ...

  • Hobart H0210G1 - page 19

    – 19 – Verify Ignition Module Safety Lockout Functions (Gas Ovens) 1 . Verify ignition module safety lockout functions. A. Turn the oven ON and close the door. B. Set the oven control to call for heat, make sure convection fan is running and the burner has established a flame. 1 # t h g i Ld e s o l c t i m i l h g i H 2 # t h g i L e r u s s e ...

  • Hobart H0210G1 - page 20

    – 20 – D E D E E N S A Y P O C S R E B M U N L A I R E S / L E D O M R E N W O D E D N E M M O C E R T S I L K C E H C E C N A N E T N I A M E V I T N E V E R P S A G - S N E V O K C A R Y R E K A B L L A C N. A E L C R O N O I T A R E P O R E P O R P R O F K C E H C Y R A S S E C E N S A E C I V R E S R O F s p m a l n e v o t c e p s n I s a ...

Manufacturer Hobart Category Convection Oven

Documents that we receive from a manufacturer of a Hobart H0210G1 can be divided into several groups. They are, among others:
- Hobart technical drawings
- H0210G1 manuals
- Hobart product data sheets
- information booklets
- or energy labels Hobart H0210G1
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hobart H0210G1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hobart H0210G1, service manual, brief instructions and user manuals Hobart H0210G1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hobart H0210G1.

Similar manuals

A complete manual for the device Hobart H0210G1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hobart H0210G1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hobart H0210G1.

A complete Hobart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hobart H0210G1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hobart H0210G1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hobart H0210G1, that we can find in the current document
3. Tips how to use the basic functions of the device Hobart H0210G1 - which should help us in our first steps of using Hobart H0210G1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hobart H0210G1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hobart H0210G1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hobart H0210G1?

Use the form below

If you did not solve your problem by using a manual Hobart H0210G1, ask a question using the form below. If a user had a similar problem with Hobart H0210G1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)